Search Documents

By Ihsan B. Tulu, David F. Gearhart, Gabriel S. Esterhuizen

"Ground deformation and support response was monitored in a longwall gateroad as part of a research project into gateroad stability under changing loading conditions. In this study, instrumentation was installed in a gateroad located between two active longwall panels. The first panel to pass was the second panel in the district, and the second panel to pass the instrumentation sites was the third panel in the district. All of the panels in the district were right-handed. All of the instrumentation was installed in the number one entry, the tailgate, the second panel to pass the instrumentation sites at a mid-pillar location, and at an outby intersection location under about 600 feet of cover. The instrumentation included roof extensometers, cable bolt load cells, hollow inclusion cells, borehole pressure cells, standing support load cells, and convergence sensors, and a multipoint borehole extensometer. The roof extensometers measured roof convergence and sag. The cable bolt load cells measured the roof load applied to the cable bolts in the secondary support array. Hollow inclusion cells measured the magnitude and direction of the principal and shear stresses. The borehole pressure cells measured the stress on a pillar in the entry nearest to the second panel to pass the instrument site. The instrumented wood cribs in the entry nearest the second panel recorded the closure and load on the cribs, and the multipoint borehole extensometer in a pillar closest to the second panel recorded the location and width of cracks that occurred and total expansion of the pillar. This paper describes the effects of the changing stress caused by the first panel as it approached and passed the locations of the instruments on the opposite side of the gateroad system and the later effect caused by the second panel as it approached and passed the mid-pillar instrument location. The first panel passing caused significant loading at the mid-pillar instrument location, but not at the intersection location, while the second panel had passed the mid-pillar location and just arrived at the intersection location when the dataloggers needed to be removed."

Jan 1, 2017

By Pinnaduwa H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior of the rockmass surrounding the underground mine excavation. The aim of this study was to investigate, at the threedimensional level, the geotechnical behavior around a tunnel excavated in a metal mine in China. A three-dimensional numerical model was built by using the 3DEC software package to simulate a tunnel excavation under a high in situ stress condition and by relying on the information available on lithology, geological structures, in situ stress measurements, physical and mechanical properties of intact rock, discontinuities, and interfaces between different rocks. The authors also investigated the effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or equivalent continuum material and rock support system on the deformation, and stability around the tunnel. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses with appropriate geomechanical property values.

Jan 1, 2013

By Tom Blevins, Roland Walker, Jinsheng Chen

"The Dywidag-Systems International DSI Tandem Anchor bolt, with an improved expansion shell-washer design, can substantially reduce potential entry roof falls caused by twisted or deformed expansion shells of the traditional mechanical anchor bolts during installation. In addition, the improved anchorage system can also ensure that a consistent and high installed load is achieved, which is critical for effective beam building under thinly laminated or layered roof conditions. This paper discusses the genesis and anchorage performance of the Tandem Anchor bolt, and analyzes the tension/torque relationship of different mechanical shell anchors using data obtained from both lab and field tests. It also discusses roof bolting mechanisms, roof bolting systems, and factors influencing effective beam building. Finally, numerical modeling was used to analyze the effect of bolt pretension magnitude on entry roof stability.INTRODUCTIONThroughout the history of underground mining, keeping the roof from uncontrollable collapse has been the greatest concern of the miner. Tremendous strides have been made in better understanding, predicting, and supporting the mine roof. This conference has spent the last twenty-eight years sharing information and distributing it to the mining community. A paraphrased statement from former Secretary of Defense Donald Rumsfeld adequately describes the challenges to the mining engineer as it pertains to roof control: it is a study of known knowns, known unknowns, and unknown unknowns. It is the hope of the authors to address some of these unknowns.The paper discusses the development of bolt anchorage systems from dry shells to shells with resin-assisted anchorage. It looks at some of the issues faced with the anchorage shells being used when introducing the insertion pressures caused by resin cartridges. The rationale behind the shell design changes was to compensate for this resin induced stresses.An improved expansion shell assembly (a slotted expansion shell base, a tapered cramming plug, and a novel support nut with tapered top) for mine roof bolts makes up the Tandem Anchor (U.S. Pat. No. 6742966); this minimizes the possibility of twisting seen with traditional mechanical shells and thus prevents springy bolts and shell leaves from breaking. A fully grouted Tandem Anchor bolting system has the advantages of both the pure mechanical point-anchor and the non-pretention fully grouted bolting systems. Once installed, the installed load or pretension will be locked in and never bleed off. Compared with the fully-grouted (2-speed resin) tension rebar bolting system, the fully-grouted Tandem Anchor bolting system can (a) reduce bolting cycle time (about 15 seconds per bolt), boosting coal production and productivity; (b) provide a greater installed load or pretention; and (c) achieve a consistent tension/torque ratio, which gives better bolting quality control. Therefore, a fully grouted Tandem Anchor bolting system is the most effective means to reinforce a weak rock mass intrinsically by the theory of beam building. For thinly laminated or layered roof conditions, a higher installed load or pretention (50% or more of the bolt's yield strength) can make a roof bolting system much stiffer, which results in less roof movement. Numerical modeling results show that the magnitude of the roof's tensile stress and relaxation zone can be substantially reduced under a higher installed load or pretention."

Jan 1, 2010

By James Pile

Since C.C. White introduced coalmine roof trusses in 1967. many different systems have evolved. Beginning in the mid 1990's, several types of bar/cable truss systems have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, this new truss increases operator safely. In order to fully benefit from the new truss system, a closer look at the individual components and their interaction was undertaken to understand critical implications on preload and overall support capabilities.

Jan 1, 2004

By Zbigniew Lubosik, Stanislaw Prusek

"The main elements of hard coal extraction systems in the Polish mining industry, including the characteristics of gateroads, are described, followed by several dozen underground measurements of gateroad roof sag performed in different geological and mining conditions in Upper Silesia Coal Basin.Based on the analysis of the roof sag measurements, an attempt to describe the gateroad roof sag process using a geometrical model was made. To build the model, it was assumed that the roof sag curve could be described by three straight lines. The first line describes the roof sag ahead of the longwall face; the second line, the sag at the longwall-gateroad junction zone; and the last line describes the zone behind the longwall face. Determining the intersection points and inclination angles is essential for the model. These model parameters depend on the geological and mining conditions in the gateroad.Using the statistical computations and analysis, the dependencies between the characteristic points of the gateroad roof sag model and the selected geological and mining parameters were defined. The STATISTICA computer program by StatSoft was used for computation.This paper presents a simple form of the geometrical description of roadway roof sag progression that is very useful during the gateroad support design process.INTRODUCTIONThe longwall system with caving is the dominant method in European mining in cases of hard coal seam extraction. For instance, in Poland, in 2009, 117 longwalls were driven, with total production of 77.5 million tonnes. In roughly 95% of the longwalls, mining operations were conducted using longwalls with roof caving; the remaining 5% used the hydraulic stowing system. The average mining depth was about 700 m (2,297 ft), and average daily output per face was approximately 2,600 tonnes per day. When using the longwall mining system, gateroads play an important role. These principal roadways transport materials, mine crews, and output. In addition, they impact ventilation of the extraction area, affecting, among other things, the climatic conditions or methane hazard. Unfortunately, difficulties often appear in maintaining an adequate size for the gateroads, due to the face line, which causes origination zones with stress concentration around the gateroad, resulting in rock mass movements in the form ofroofsag, floor heave, or horizontal convergence (Figure 1)."

Jan 1, 2010

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By Tom Barczak

Early in my career, while giving a presentation on shield design for longwall mining at one of the International Conferences on Ground Control in Mining, the late Jim Scott told me that I was finally getting it, because ?I was starting to think like a rock!? Although I didn?t realize it at the time, those few words changed my career forever. At the start of my career, I did a lot of laboratory testing, taking advantage of the unique capabilities of the Mine Roof Simulator to study the performance and design characteristics of longwall shields. I had a pretty good handle on what made shields work and what made them fail, but I was still struggling with how and why they develop their in-service loads and what they were actually controlling as opposed to being passive bystanders in a world beyond their control. It became clear to me that the simplistic models of dead weight loading could not explain the behavior I saw and measured underground. The problem did not go away when I started studying standing support systems. Again, I learned much about the strength, stiffness, and stability of these supports and helped the industry develop several new support products that attempted to provide more efficient support designs. But here, too, the simplistic models of dead weight loading did not seem to fit for me. That?s when I began to incorporate the ground reaction concept as a way of integrating the support response and the ground behavior into a cohesive design methodology. The concept has its limitations, no doubt, but I believe some form of it will be the future of not only designing supports but also, in the broader sense, enhancing the engineering aspects of ground control. The paper presented at the International Conference on Ground Control last year by Esterhuizen (2010) on pillar behavior is evidence of this. Think like a rock. Jim Scott was right. It takes two to dance. You can?t dance alone and you will never understand ground control by thinking like a support! ?Dumb as a box of rocks?? I don?t think so. The answer lies in the rocks!

Jan 1, 2011

By Nan Zhou, Jixiong Zhang, Qiang Zhang

"Mining activities under hard roof could easily induce rock burst. Based on the geological conditions of widespread hard roof in China, this paper discusses the type, mechanism of occurrence and prevention of rock burst caused by hard roof from energy evolution point of view. It analyzed the interaction between the solid backfilled body and roof under different backfilling ratios. And by establishing and applying the mechanical model, the deformation of hard roof and energy evolution of the panel under different backfilling ratios were determined, revealing the control effect of solid backfilling on disaster-causing energy. As a result, an innovative method using the solid backfilling method was proposed as a solution to the hard-roof-induced rock burst hazards. Moreover, mine trial was conducted in Panel 6304-1 of Jisan Mine. The result shows that the stress concentration factor of the front abutment stress was only 1.44; the coal dusts in drill holes didn’t exceed the limits and microseism of large energy didn’t occur during mining mining, indicating that solid backfilling mining could be applied as an effective method for preventing rock burst caused by hard roof.INTRODUCTIONSHard roof refers to the thick strata above the coal seam or thin immediate roof. It is strong with poor joint development. After mining, instead of immediate caving, it will overhang for a large area in the gob, resulting in high stress in front of the face and difficulty in gas dispersion. As a result, the face spalls, the roof exposes and the gas accumulates in the gob. With the continuing advance of the face and increase in area of overhang, the stress in the hard roof will eventually exceed its ultimate strength and cause a large area of caving, followed by quick release of energy concentrated in the roof and coal seam, which may cause rock bursts and other dynamic disasters in the mine as well as serious equipment damage and casualties. Therefore, the hard roof becomes one of the main factors causing rock bursts at the face.Hard roofs in China varies in conditions. It ranges from dozens of meters to hundreds of meters in thickness. However, coal reserve under hard roofs accounts for about 1/3 of the total reserve; moreover, nearly 40% of the fully-mechanized coal mining panels are those with hard roofs and more than 50% of the mining areas are associated with problems of hard roofs. Aiming at this problem, researchers at home and abroad have proposed many solutions, e.g. coal pillar support, strength weakening and forced caving, to prevent rock bursts caused by hard roof. These solutions have been employed in some cases with good results. However, due to the variability in geological conditions of mining and hard roofs, the application of the above solutions is limited."

Jan 1, 2015

By Michael Murphy, Khaled M. Mohamed, Berk Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in underground coal mines to reduce rib fall accidents and fatalities. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified.This paper presents a coal rib model to simulate the mechanism of coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff Mine in Australia. Fracturing of the coal rib was defined by critical VALUES (of plastic shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data.INTRODUCTIONCoal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face failure and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities (MSHA, 2015)."

Jan 1, 2016

By Zbigniew Lubosik, Andrzej Walentek, Stanislaw Prusek, Aleksander Wrana

"The Carboniferous coal measures, mined across Europe including the major European underground coal mining countries of Poland, UK, Germany, and Czech Republic, suffer from increasing extraction depth. This results in major geomechanics problems associated with ground control and support design.With production being concentrated into ever fewer high performance longwalls, located at greater and greater depth, pressure to ensure the roadways’ functionality (required dimensions) continues to increase. Mining in deeper and more highly stressed mining environments creates several problems. The high stress and deterioration in geological and mining conditions in many cases causes problems with gateroads maintenance (due to excess convergence). That leads to costly production gaps, longwall slowing, transport problems, an increase in the methane hazard and in the general health and safety of the workforce, and deterioration in climatic conditions with major economic risk associated with interruption of the revenue stream. Time—and thus production—delays due to maintenance often result from insufficient geological and geotechnical data acquisition and misinterpretation combined with inadequate support for the type of rock mass.longwall face on the gateroad stability (described by the gateroad convergence, support load, and shape and height of the fractured zone around the longwall gateroad) are presented. The investigations were carried out in the longwall panel with roof caving located at the great depth, in conditions of the Upper Silesian Coal Basin in Poland.The measurement results showed that the gateroad fractures in roof strata began to occur at the distance of about 1000 m ahead of the face. Additionally, the load on support and gateroad convergence increased as the longwall face got closer.It is very important for coal mining research institutes and mine operators to investigate and develop practical solutions and apply innovative support technologies at a great depth (particularly for reinforcement and stabilization of roadways and other openings).Underground measurements of stability conditions around the gateroad is of great importance to mining practice, especially in planning and designing supports for longwall gateroads.The influence of the front abutment pressure results in an increase of support load, gateroad convergence, and shape of fractured rock zone."

Jan 1, 2015

By Michael J. Peacock

The Powhatan No. 4 Mine is located in southeastern Ohio along the Ohio River in Monroe County. The mine produces approximately 3.2 million tons of steam coal annually from the Pittsburgh No. 8 seam. The Pittsburgh No. 8 seam in this area dips to the southeast in varying amounts from 10-feet to 40-feet per mile. The seam is made up of a main bench coal (4' to 5f' ) containing several thin and variable partings and a rider ("roof") coal (0" to 18") which is separated from the main bench by a parting (0" to 18") that is reasonably consistent in occurrence and position. Strata overlying the seam varies from a bedded to nonbedded calcareous mudstone-claystone (6' to 12') in the north and east regions of the mine to a sandstone (Pittsburgh Sandstone C10' to 40'1 in the south and west regions. The Redstone Limestone (10' to 18' ) overlying the mudstone-claystone in the north and east thins and rises toward the area of sandstone deposition in the south and west. From its opening in April of 1971 until late 1981, primary roof support in the long-1 ived entries at Quarto Mining Company's Powhatan No. 4 Mine had been achieved with 8-foot and 10-foot. 518-inch mechanical roof bolts using a Single expansion shell. These bolts were installed so that the expansion shell achieved a competent anchorage in the limestone. However, as the mine developed westward, the limestone began to trend upward becoming inaccessible as an anchorage medium at the 8-foot and 10-foot horizons. Anchorage achieved in the underlying mudstone-claystone strata was failure-prone due to weathering (after exposure to air and moisture) and inconsistencies in the anchorage horizon, leading to an increase in the incidence of reportable roof falls at the mine. Responding to the threat to safety and productivity posed by the increase in roof falls. Mine Management through its Safety and Engineering Departments, sought solutions to the problem. In seeking a solution to the problem, the safest and en engineering groups examined the reportable roof falls to determine the cause of those failures. Their examination pinpointed two items which were found to be a common link in the majority of those falls; namely, anchor integrity and geologic trends. Analysis of the roof falls indicated that due to effects of air and moisture on the anchoraae zones in the mudstones and clay- itones, the integrity of the anchorage over time could not be maintained. Geologic trends noted included the upward trend of the -main limestone as mining progressed westward, inconsistencies in the amount of roof coal and draw slate in the immediate mine roof and increasing evidence of heavily slickensided immediate mine roof. In the absence of the protective barrier provided by the roof coal, the immediate strata and particularly the draw slate, is susceptible to deterioration due to the weathering effects of air and moisture and thus is prone to "eat out" around the roof bolts and cause roof falls. The presence of heavily slickensided roof creates a need for increased contact surface such as that provided by plank and header blocks to aid in holding up the roof and tends to make the behavior of such roof very unpredictable. Having determined the causes of the roof falls. Mine Management began to identify the kind of roof support which would best solve these problems, while at the same time providing the mine with a safe, cost effective and efficient roof support system. This paper will provide an analysis of how this decision was reached, the background that was researched to aid in forming the decision, the considerations that played key roles in the formulation of the plan, the mechanics of following through and implementing the new roof support system, and an assessment of the resultant gains in safety, productivity and improved costs derived from the implementation of the new roof support system.

Jan 1, 1986

By Gamal Rashed

Coal bump is a sudden manifestation of the release of strain energy stored in a coal pillar (Peng, 2008). It is a very serious mining hazard that adversely affects the safety and productivity of the mines. Several case histories in mining have described coal pillars or faces of coal failing violently with an accompanying ejection of debris and broken material into the working areas of the mine (Campoli, 1987; Osterwald, 1962; Peperakis, 1958; Garvey and Ozbay, 2013). These failures resulted in large losses of life and total collapses of entire mine panels (Chase, Zipf, and Mark, 1994; Zingano, Koppe, and Costa, 2004). There are questions in the literature about whether or not the coal itself plays a significant role in bump. Rice (1935) mentioned that structurally strong coal is one of the key factors for bump; however, the strength of the Pocahontas #3 coal seam is low, and it bumped. Moreover, it is not obvious in the literature whether the strength of the tested coal samples is the inherent strength or if it is influenced by the shape or the size of the specimen. The main objective of this paper is to answer the following question: To what extent does the mechanical properties of the coal have an impact on the potential for violent failure? The best approach to answer this question is to compare the mechanical properties of two kinds of coals from bump-prone (Utah coal-Sunnyside seam) and non-bump-prone (WV coal-Sewickley seam). This comparison includes uniaxial compressive strength, modulus of elasticity, shear strength (cohesion and friction angle), and the burst index.

Jan 1, 2014

By Rajendra Singh

Considering the importance of a fully mechanized depillaring operation, the Indian coal mining industry has introduced a number of such depillaring operations at depths of cover ranging from 60 m to 377 m. The overlying strata of these depillaring faces vary widely from highly laminated, weak and easily caveable to massive, strong and difficult to cave. Most of these mechanized depillaring operations were carried out in difficult site conditions, however, performance monitoring in the field has showed good production, productivity and safety results. Field studies have shown that the use of roof bolts as breaker line support for this technology worked well for moderate strength overlying roof strata, but experienced difficulties for both extremely weak and strong/massive overlying roof strata. It is observed that the performance of a breaker line support along the goaf edge deteriorated with an increase in depth of cover of the depillaring face. Practice of a straight line of extraction (single row of pillars) during the mechanized depillaring below competent roof strata experienced a considerably large hanging area inside the goaf, which needs to be managed either by induced caving of the roof strata or through an increase in width of the excavation. Observations of good performance of a fully mechanized depillaring face under highly laminated and weak strata at a shallow cover is mainly due to a faster rate of extraction. However, the mechanized depillaring underneath laminated and weak roof strata for a deep-seated coal seam was forced to go for partial extraction mainly due to strata control problems. Discussing the implications of main technical and operational differences between the conventional (semi-mechanized) and fully mechanized depillaring, this paper presents results of different strata control studies conducted at different mechanized depillaring sites with varying geo-mining conditions.

Jan 1, 2014

By Timothy Batchler

"Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. Because different pumpable supports are visually similar and installed fundamentally in the same manner as other supports, there is a tendency to believe they all perform the same way. However, there are several design parameters that can affect their performance, including the cementitious material properties and the bag construction practices that influence the degree of confinement provided. A full understanding of the impact of these design parameters is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance.This paper evaluates the impact of various support design parameters by examining full-scale performance tests conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) as part of manufactures' developmental and quality control testing. These tests were analyzed to identify correlations between the support design parameters and the resulting performance. Based on more than 160 tests over 7 years, quantifiable patterns were examined to assess the correlation between the support dimensions, cementitious material type, wire pitch, and single-wall vs dual-walled bag designs to the support capacity, stiffuess, load shedding events, and yield characteristics.INTRODUCTIONDeveloped in the 1990s, the first major use of pumpable supports systems in U.S. longwall operations was in the support of bleeder entries (Barczak, Tadolini, 2008). Since then, they have been utilized as yieldable concrete supports to provide a safe working environment for longwall mining gateroads, bleeders, and emergency escapeways while also maintaining adequate ventilation pathways. The basic structure of pumpable roof supports has remained unchanged over the years. Formed in place with a twopart fast-setting grout, the support material can be pumped into a containment bag from several thousand feet away often through surface boreholes. The containment bag then acts as a form to fill the support and provides confinement to the grout during loading and after failure. Pumpable roof supports provide full contact with the mine roof and floor, which eliminates the need for secondary material to establish proper roof contact (see Figure 1). They provide a high peak load capacity and a sustained, confinement controlled yield behavior while maintaining stable ground conditions, which is essential to underground mining operations."

Jan 1, 2016

By Nikzad Oraee, Parham Khajehpour, Kazam Oraee, Arash Goodarzi

"Rock fall related accidents continue to occur in coal mines, although artificial support mechanisms have been used extensively [1]. Roof stability is primarily determined in many underground mines by a limited number of methods that often resort to subjective criteria. It is argued in this paper that stability conditions of mine roof strata, as a key factor in coal mines, must be determined by a survey which proactively investigates fundamental aspects.Failure of rock around the opening happens as a result of both high rock stress conditions and the presence of structural discontinuities. The properties of such discontinuities affect the engineering behavior of rock masses causing wedges or blocks to fall from the roof or slide out of the walls [2]. A practical rule based approach to assess the risk of a roof fall is proposed in the paper. The method is based on the analysis of structural data and the geometry and stability of wedges in underground coal mines. In this regard, an accident causing a huge collapse in a coal mine leading to four fatalities is illustrated by way of a case study. A comprehensive investigation of the hanging wall has been gathered through a systematic collection of evidence. The investigation results are then analyzed, and an interpretation of the evidence gathered is provided.For this purpose, horizontal and vertical profiles are prepared by geophysical methods to define the falling zone and its boundaries. The collapse is then modeled by the use of sophisticated computer programs in order to identify the causes of the accident and hence recommend corrective actions to prevent or minimize reoccurrence probability of similar accidents. The corrective measures are placed into a rule-based framework for the benefit of the mine operators.INTRODUCTIONRoof rock failure has generally been the most dangerous hazard for underground coal mining in the world. Failure of rock around shallow coal mine openings often results from loosening of blocks of rock on the weakened planes under the influence of gravity. This condition is not typically seen in large deep coal mines. There are a number of differences between large mechanized mines and small mines related to ground control [3]."

Jan 1, 2015

By Heather E. Lawson

Recent field data providing measured pillar loading from a deep western mine revealed that an increased load transfer distance existed compared to expected values (Larson et al., 2012). Additionally, recent work by Tulu and Heasley (2012) has shown that the abutment angle in deep longwall mines can be significantly reduced as the depth of mining increases. The load transfer distance and abutment angle are both used as parameters to estimate pillar loading in longwall design. To investigate the potential implications of these observations on pillar loading in deep longwall mines, a parametric study using ALPS loading estimation procedures was performed. A supplemental study was conducted using LaModel to further investigate pillar loading at the tailgate. The study found that the abutment angle is particularly important for panels with supercritical geometries. As panels reach a subcritical geometry with increasing depth, the primary influence of the abutment angle is reduced and matched by other factors, including load transfer distance for tailgate loading. An extended load transfer distance was shown to potentially reduce loading on pillars adjacent to the longwall as the loading is spread over a larger area. The results of these studies indicate a need for further field verification and research toward regional geologic influences on pillar loading and how these may impact ground stability.

Jan 1, 2013

By David Bigby

Rock Mechanics Technology has developed an intrinsically safe remote reading telltale system which allows up to 4 sets of 100 dual height, water diverting telltales in a mine roadway to be remotely monitored from a surface PC. The system has US MSHA approval and European ATEX approval for use in gassy mines. A successful full-scale application of the system employing 67 telltales was completed in a 1300m long maingate roadway during retreat of 183.0 longwall panel at West Mine in Germany between June 2001 and October 2002. During panel retreat a number of "teething" problems associated with the system were identified and resolved, the chief problem being associated with cable connection corrosion due to the unforeseen use of sprayed calcium chloride in the roadway. This paper describes the experience of employing the system at the colliery from the perspective of both the user and the manufacturer, and the improvements and developments which have resulted. The paper also presents examples of roof movement data recorded by the system, including data from behind the retreating longwall. The high resolution and data recording rate possible has resulted in particularly interesting information on roof behavior within the longwall front abutment area and behind the face. The paper also describes a series of new transducers and extensometers for the mining industry which employ the same physical principles and similar electronics to the remote reading telltale system. These have been applied in a variety of mining and tunneling environments worldwide over the last two years.

Jan 1, 2003

By Xinzhi (Thomas) Du

"In order to monitor the overburden strata deformation over a longwall mining area in the Pittsburgh Coal Seam, three boreholes were drilled across the longwall panel. Each borehole employed multiple-point borehole extensometers (MBE) to monitor overburden strata movement during and after the longwall face passed under the study area. The longwall face in the study area was 1,428 ft wide and 4,000 ft long. The average mining height was about 7 ft. The overburden depth ranged from 550 ft to 650 ft with an average of 600 ft. The final extensometer readings indicated that overburden strata initially showed sign of movement when the longwall face was 700 ft inby the MBE. The rate of strata movement accelerated when the face was 300 ft inby MBE. When the face was directly under MBE, a sudden anchor displacement occurred, indicating rapid strata movement once under-mined gob. The readings showed insignificant strata movement after the longwall face was 400–700 ft outby MBE.INTRODUCTIONThe longwall mining method is an efficient mining method of underground mining. Surface and subsurface strata are inevitably disturbed above the longwall mined out gob. Figure 1 shows the four zones of disturbance in the overburden strata in response to longwall mining.A longwall shear cuts the coal seam and allows the immediate roof strata to cave into irregular blocky material to fill the void. This is called the caved zone. The caved zone extends from the mining horizon to six or eight times the mining height, depending on the bulk factor of each caving strata layer. The fractured zone is located above the caved zone, in which the strata breaks into regular blocks by vertical or sub-vertical fractures caused by bending forces due to the weight of the underlying strata. The surface soil and rock crack zone extends to approximately 50 ft below the surface. The surface cracking is caused by downward movement of the surface. Between the fractured zone and surface crack zone is the continuous deformation zone. The strata in this zone deforms gently without causing any major cracks that extend long enough to cut through the thickness of the strata, as in the fractured zone (Peng, 2006).The objective of this project is to provide fundamental rock mechanics research about overburden strata movement response to longwall-related activity. The findings aid in better understanding pillar stability, gas well subsidence management, hydraulic impacts, and numerical modeling."

Jan 1, 2018

By Ted Klemetti, Gabriel Esterhuizen, John L. Ellenberger

"Advanced numerical models can be used to evaluate entry support systems in coal mines. However, these methods require specialized software and specialized skills to create the models and evaluate the results. Practicing support design engineers require a method to rapidly assess a proposed support system for a given geotechnical scenario. A prediction equation that can be used to assess roof support systems has been developed from the results of hundreds of FLAC3D analyses that were conducted during recent research. These models were validated against field cases and empirical design approaches and were found to adequately predict entry stability in coal mines. The understanding developed from the model outcomes was used to develop an equation to predict entry roof stability against large roof falls. Least-squares error analysis was conducted to find appropriate parameters for the nonlinear equation. The developed equation can be solved using spreadsheet software, allowing for rapid assessment of alternative support system performance in variable geological conditions. The performance of the prediction equation is evaluated against empirical design methods and against selected case histories of support practices at currently operating mines. Examples are presented that demonstrate the performance of the equation in variable geological settings. The stability factor (SF) prediction equation can be used as an assessment tool to assist in the design of coal mine roof support systems.IntroductionGround falls represent a significant proportion of injuries and fatalities in underground coal mines in the US. During 2013, ground falls were responsible for 4 of the 14 fatalities and 16.6 % of the 1,577 reportable lost-time injuries (MSHA, 2015). In addition, each year about 400 to 500 large roof falls are reported that can extend up to or above the bolted horizon. Large roof falls and associated ground fall hazards can be mitigated through improved support design.The research presented here particularly addresses the problem of large roof falls that extend more than 90 cm (3 ft) above the roof line of an entry and may extend above the bolted horizon. Smaller roof falls that fall out between supports or extend less than 90 cm (3 ft) above the roof line are excluded. These smaller roof falls can be controlled by appropriate surface support such as roof screen or other skin control methods. Also excluded are roof falls that are associated with an individual geological structure such as a slip of fault. Structure-related instabilities can be controlled by strategically locating individual roof bolts or other supports appropriate for the local situation."

Jan 1, 2015

By Dion Pastars

Resin based grouts are the main form of rock bolt anchorage in the underground coal industry in Australia and New Zealand. To be effective, the system requires the mixing of the catalyst and mastic components of the resin, as well as shredding of the laminate cartridge that contains the resin. An unknown measure is the load transfer characteristics of a bolt where the resin is well mixed but remains encased in the cartridge (gloved). Laboratory and in situ field investigations have been undertaken to quantify the performance loss due to mixed gloved bolts. This work showed repeatable results, indicating serious performance loss of the gloved and mixed system, with load transfer approximately 10- 15% of a non-gloved system (MacGregor, 2004). The in situ testing has demonstrated the relationship between the adhesion qualities of the resin and the mechanical interlock generated by radial confinement with progressively increasing tensile load. Effective load transfer is defined by the ability of the system to sustain shear stress on the bolt hole wall.

Jan 1, 2005