Search Documents

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem. Combined permeability and leaching tests were done in the laboratory on samples of clay bearing ores to evaluate a clay-stabilizing polymer's effectiveness in preventing the problem. Test results indicate that treating the ores with cationic polymers could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability leaching tests. To determine the reasons for the success of the clay stabilizing polymer, clay swelling tests and zeta potential measurements were made on untreated ore samples and on ore samples treated with the cationic polymer. Test results indicate the cationic polymer could reduce the degree of negative charge on fine particles and their tendency to disperse, as well as reduce clay swelling. Test results indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure during leaching, if clays and fines are kept stabilized. This may be done by treating the zone of high fluid velocity near injection wells with cationic polymers.

Jan 1, 1991

By B. R. Satio, P. G. West-Sells, D. B. Dreisinger, B. J. Y. Leong, G. A. Kordosky

Electrolytic techniques have historically been used to remove arsenic, antimony and bismuth from copper refining electrolytes. However, both solvent extraction and ion exchange techniques have been heavily researched and in a number of cases commercially introduced. In this study a large number of solvent extraction reagents and ion exchange resins were screened to determine the selectivity of the reagents for impurity removal. Solvating extractants were found to efficiently remove arsenic from electrolyte. The extent of arsenic extraction increased in the following order: TBP < DBBP < DPPP < Cyanex 925 < Cyanex 923. Antimony and bismuth extraction from electrolyte were demonstrated with the reagent 2EHAP04. The ion exchange resins UR-3300 and Duolite C-467 were found to strongly extract antimony and bismuth from electrolyte. C-467 appeared to be superior to UR-3300.

Jan 1, 1993

By M. Laliberte

"Gold-mine effluents are often characterized by high concentrations of copper, ammonia and cyanide derivatives (mostly cyanates and thiocyanates). While not acutely toxic to birds, this water can be acutely toxic to fishes and invertebrates. In many jurisdictions, the effluent requires further treatment in order to pass a mandatory requirement to be nonlethal to species like the rainbow trout (Oncorhynchus mykiss) or Daphnia magna. Using actual mine water, it has been demonstrated that aerated moving bed biofilm reactors will biodegrade the ammonia, cyanides, cyanates and thiocyanates, thereby removing the toxicity associated with these components. By removing copper by precipitation the water can be made to pass acute toxicity tests. Tests have demonstrated that the process is stable between 4 and 25°C, with no significant changes in the treated water composition. Once the biomass is acclimatized, the process is resistant to upsets and requires very little inputs except for phosphorus and air. Furthermore, it has been demonstrated that an anoxic reactor can be added downstream of the aerated reactors to remove nitrates if required.IntroductionThis paper will demonstrate that gold-mine effluents, which are toxic to fishes and invertebrates, can be made nontoxic by using a combination of chemical precipitation and biological oxidation.The typical composition of gold-mine effluents will first be described. The applicable legislation will then be introduced, with its requirement that the treated effluent be nontoxic. The toxicity of a typical untreated effluent will then be confirmed, and the sources of the toxicity identified. After that, a number of toxicity reduction treatment methods will be presented, and the selected method will be described.The lab tests that confirmed the efficiency of the treatment method will be presented, with three phases of testing as the understanding of the process gradually improved. Toxicity test results showing that the water is nontoxic after treatment through the temperature range will be presented."

Jan 1, 2015

By John W. White

Anthracite mine refuse, or culm dump material as it is sometimes called, is the waste material resulting from the sizing and cleaning of run-of-mine deep and strip-mined anthracite coal. It may also contain mine rock, carbonaceous shale, pyrite, and other debris from mining operations. This material is generally stored in piles or banks, some of which are over 100 years old. Many of the older banks contain a considerable amount of good coal, particularly in the finer size ranges, since these sizes did not have any particular economic value in the early days of anthracite mining. Today, the refuse material from a cleaning operation must be piled in an orderly fashion and in such a way as to minimize the tendency to ignite. There are well over 400 of these banks in the anthracite region containing over 1100 million tons of refuse located in the north-eastern part of Pennsylvania. The banks range in size from a few thousand tons of material up to as much as 13 million tons. Most of

Jan 1, 1972

By C. Rodriguez, T. BoBo

Comminution, being the energy intensive part of a mining operation receives much scrutiny by cost controllers, CEO’s, investors and others as the mining industry goes “back to basics” to reverse the decline in productivity which occurred during the mining super cycle. Blasting is the first and lowest cost per ton stage in the comminution value chain. The basic principle that effective blast design can optimize fragmentation from the Run of Mine (ROM) ore muck pile to improve productivity through digging, loading and crushing to grinding and increase mine site profits has been well documented. Benefits of controlling fragmentation in the blast include reduced wear on equipment, faster loading, increased truck loads while detecting oversize rocks at the muck pile can reduce the frequency of a blocked primary crusher. A second basic principle is a measure of particle size distribution (PSD) at each unit operation in the comminution cycle allows engineers to manage blast design to produce fragmentation in the ROM ore most suitable to optimize downstream unit processes to improve mine site productivity and profits. Split-Online® systems have measured PSD of rocks on conveyors from the primary crusher to the SAG mill for over 20 years. Split-Engineering partnered with various mining companies to develop Split-ShovelCam® to automatically measure fragmentation from shovels and excavators working the ROM muck pile. This paper takes the reader “Back to Basics” by discussing the use of real time fragmentation analysis at the muck pile as an important parameter to optimize energy factors required for each blast. Case studies are given. INTRODUCTION The basics of mining are: • Explore for and find economic resources of valuable minerals • Mine rocks containing valuable minerals using blasting • Crush and grind rocks to liberate valuable minerals (comminution) • Recover valuable minerals for sale Comminution is an energy intensive process which accounts for a major proportion of mine site costs. Effective blasting can improve comminution and deliver significant reductions to mine site unit costs, (CEEC, 2016). Engineers, scientists, builders and even philosophers have long promoted the phrase “measure to manage”; the premise being “you can’t improve what you don’t measure”. Blast Engineers measure fragmentation in ROM ore for feedback to manage energy input in the design of blast patterns to optimize the ROM product size for downstream operations, whether they be for ROM Leach or feed into the primary crusher.

Jan 1, 2019

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of screens were developed for the Coal Cleaning Simulator running under Aspen Plus during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for the size separation and a calculation for moisture content of the oversize product based on particle size and specific gravity distribution. This paper discusses the algorithm for predicting the moisture content of coal dewatered by screens.

Jan 1, 1997

By John A. Wolfe

The concepts of sea floor spreading and plate tectonics provide more logical explanations of some geologic processes than were possible a few years ago. I plan to premise my discussion of the regional features of Philippine porphyry copper deposits on this tectonic basis, recognizing that parts of the picture can be explained in other ways, but in the belief that this is the best explanation of the whole. The sequence of events which results in the formation of Porphyry deposits (Figure 1) can be summarized as the result of collision of crustal plates, subduction of the oceanic plate, emplacement of a serpentine ultrabasic diapir, formation of a dioritic magma at depths of 300 to 500 km, rise of the magma to a sub crustal or intra-crustal chamber, eruption of andesitic volcanoes, emplacement of diorite or differentiation of the magma into more acidic products, multiple intrusion of hypabyssal rocks and hydro-

Jan 1, 1973

By Nathaniel Arbiter

The increasing size of flotation cells as the use of flotation has increased is traced from the first United States application of the process in Montana in 1911 through the following eight decades, using data from the Taggart handbooks (1927) and (1945), from the SME Handbook (1984), and from recent manufacturers&apos; catalogues and other sources for the 1980s and 1990s. With the earliest mechanical cells less than 1 m3 (359) in volume and the largest now available at 200 m3 (7,000ft3), three requirements are necessary: 1) demonstration of advantages in replacing smaller volume by larger volume cells; 2) estimating power requirements, impeller dimensions, and operating rpm by correlation equations; 3) considering effects of using larger cells, in necessarily much shorter rows, on process kinetics. The resulting seven tables that address these problems are presented, and their implications discussed.

Jan 1, 1999

By L. P. Meade

The need to feed an established talc mill from a crude are source located closer to the mill prompted the drilling in 1986 of a previously mapped talc-carbonate deposit. This talc-bearing rock had never been considered as a potential source of crude talc are because of the high carbonate content and other deleterious minerals that were observed in outcrops. Selective mining, in-pit grade control and creative processing has allowed this deposit to be developed into an orebody. By definition, an orebody has to be a source of positive cash flow. With industrial minerals, this is determined as much by market acceptance as by are tenor.

Jan 1, 1992

By A. J. Lewis, P. J. Hutcheson, M. E. Robertson, P. A. Moir, K. M. Barfoot

With the content of gold and platinum in the vast majority of ore deposits typically averaging 6 parts per million and less, the accurate and precise measurement of these metals in samples of ore and mining process streams has proven very difficult to achieve by modem spectroscopic analytical techniques. Largely because no other technique has proven suitable, the basic fire assay process has become the accepted international standard for these metals. Fire assay, however, suffers a number of disadvan­tages in the modem, competitive, high technology, and increas­ingly environmentally aware world. It is a labour intensive technique that is difficult to automate, and requires high levels of skill to ensure accuracy and consistency of results. Potentially hazardous chemical reagents are employed, of which, lead, in particular, can be a serious source of contamination to both personnel and the environment if not effectively controlled. Other dangerous elements, such as mercury and arsenic, liberated in high energy furnace operations, are further sources of possible health and pollution hazards. n contrast, the energy dispersive K X-ray fluorescence (K­XRF) technique devised by K X Technology Ltd overcomes many of the technical constraints of conventional low energy X­ray analysis, and has the potential to revolutionise assay opera­tions in precious metal mining. The technology is simply automated, requires basic operator skills, uses no chemicals, consumes less than 20kW, and is capable of detecting gold and platinum to an accuracy of O .1 parts per million by mass. The new third generation design of AZTEC laboratory instrument, released in 1994, is the result of significant technical development. Capable of analysing over 1200 samples per day, and developed primarily for grade control sampling, its applica­tions have spread to gold ore accounting from on-line conveyor belt sampling; screening of exploration samples; measurement of gold in carbon granules for Carbon-in-Pulp process control; and for conducting rapid checks to support key managemen decisions. The economic, rapid, and non destructive analysis ofup to 80g of ore for large numbers of samples, reduces sampling and sub-sampling errors, and provides improved grade estimates for ore bodies. When interfaced to a LIMS, laboratory automation and cost-savings can be further enhanced. The AZTEC design is also being modified for the analysis of platinum. The GOLDSTREAM on-line analysis system is an important new application of K-XRF to the continuous monitoring of process streams in gold ( or platinum) plants and mills. Integrat­ing the technologies of K-XRF to measure total gold, and dissolved gold spectroscopy to measure gold in solution, the insoluble fraction of gold can be deduced, and the effectiveness of the extraction process determined. Slurries are sampled automatically from selected points of the plant and pumped to the system for analysis. The information produced forms the basis for plant control and optimisation.

Jan 1, 1995

By Dae S. Young, Steven F. Hoerger

The geostatistical method of indicator kriging (IK) was extended to analyze two-dimensional distributions of rock joint orientations. The IK method provides a non-parametric approach for spatial analysis of local probability distribu- tions. By taking into account the spatial correlation of rock joint outcomes and the relative geometry between estimation unit and samples, the IK method provides optimum, spatially conditioned estimates. The estimation method was tested by comparing distributions of actual mapped rock joint orientations with their corresponding kriged estimates. The comparisons show the unbiasedness and accuracy of the non-parametric approach for estimating local probability distributions.

Jan 1, 1986

By William Gleason

"During the past nine years the number of cellular phones connected to a network has increased from 34 percent of the world’s population in 2005 to 93 percent in 2014. These phones are powered by a combination of materials including elements such as gold, silver, copper and rare earths. And, as more parts of the world become connected to networks, the number of phones being produced, and the elements they will need, will continue to increase. The demand comes as prices for these commodities are slumping and access to the commodities is getting more difficult, technically and socially.These mobile devices have connected people around the world in ways that could not have been imagined two decades before, and, ironically, this communication has strengthened opposition to the development of the mines that produce the very materials they need to operate.In his keynote address to the 2014 SME Arizona Conference at the JW Starr Pass Resort in Tucson, AZ, on Dec. 8, 2014, John O. Marsden, SME President and president of Metallurgium, spoke to more than 500 attendees about the challenge to produce the materials that society needs while at the same time challenging the general public’s perception of mining that is often inaccurate and less than favorable.Marsden highlighted the amount of raw materials that will be needed not just for phones, but also for things such as automobiles, including electric cars, as a way to illustrate the importance of mining. Even so-called green products such as Tesla cars, which require about 317 kg (700 lbs) of aluminum, 13 kg (30 lbs) of copper and 36 kg (80 lbs) of cobalt for their eco-friendly batteries, will need materials mining provides.These are some of the numbers that the general public is often unaware of. They are part of the necessary things that mining provides for society but are rarely reported on. Instead, it is the accidents like the tailings spill at the Mount Polley Mine in British Columbia and at the Buena Vista Mine (Sonora, Mexico) that grab headlines and stick in the minds of the public, adding more challenges to an industry that already has its own complex technical challenges to deal with."

Jan 1, 2014

By C. Strachan

This paper presents an evaluation of tailings dam incidents from the 1994 USCOLD Tailings Dam Committee report. Comparisons are also made with water storage dam incidents from USCOLD reports and recent tailings dam incidents. The evaluation results show that tailings dam incidents are due to a number of factors including overtopping, static and seismic instability, seepage and internal erosion, and foundation conditions, and that no particular type of tailings dam or operational condition is more susceptible to incidents. In addition, the results confirm that tailings dams should be located, designed, operated, and reclaimed with a thorough knowledge of site conditions, mill operation, site monitoring, and tailings characteristics.

Jan 1, 1999

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) has been used by the mining industry for early fire detection in underground mines. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to integrate real-time AMS sensor data with NIOSH’s mine fire simulation program, MFIRE 3.0, to simulate and predict the spread of smoke that would provide assistance to mine fire emergency response personnel. Determining the heat release rate of a fire using the monitored sensor data was a critical component of the successful completion of this project. NIOSH researchers developed a direct method to calculate the heat release rate when a fire is within close range of sensors. However, this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire heat release rate for complicated scenarios where a fire is distant from sensors and airflow splits and merges are present. The method was validated using a fullscale diesel fuel fire test conducted in the Safety Research Coal Mine at the Pittsburgh Mining Research Division and can help mine operators and safety personnel make informed decisions during a fire emergency.

Jul 31, 2020

By P. K. Songfack

The transport of slurry within the ball mill depends on the peripheral velocity and porosity of the ball charge. Residence time distribution and mill hold up are of-ten used as indicators of the mode of transport. In this work, the transport problem is tackled via direct simulation of the three dimensional motion of the ball charge. In doing so, the following quantities are calculated: (i) ball size distribution as a function of the distance from the feed end of the mill (ii) mean peripheral and longitudinal velocity and longitudinal velocity of balls of different sizes, and (iii) the spatial distribution of porosity within the ball charge. Hence, the problem of transport is handled as a motion of part of the slurry with the ball charge and part as hydrodynamic flow through the porous structure.

Jan 1, 1993

By L. Zhou, D. Bahrami, Y. Xue

Underground mine fires are a threat to the safety and health of mine workers. The timely determination of the location and size of an underground fire is of great importance in developing firefighting strategies and reducing the risk of any injuries. Machine learning was used in this paper to develop a predictive model for fire location and fire size in an underground mine. The ventilation data were obtained by simulating different mine fire scenarios with MFire. The ventilation data of all airways were used as features to predict the fire location. Based on the feature importance, five airways were selected to monitor, and the airflow data of the selected airways were used to predict the fire location and fire size. An accuracy score of 0.920 was obtained for the prediction of fire location. In addition, in-depth analyses were conducted to characterize the wrong predictions with the purpose of improving the performance of the random forest model. The results show that the occurrence of fire at closely connected airways at some locations can generate misleading ventilation data for each other and the model performance can be further improved by grouping them. Fire size is another factor affecting the model performance and the model accuracy increases with increasing fire size. The result from this study can help mine safety personnel make informed decisions during a mine fire emergency.

Mar 2, 2022

By Bo-Hyun Kim, Mark K. Larson

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) have advocated the use of instrumentation in underground mine ground control studies to aid in understanding failure mechanisms and to calibrate numerical models. The purpose of these efforts is to reduce accidents and fatalities in underground mines resulting from inadequate design of mining layout or supports. A recent examination of some results of stress change measurement raised some questions about the validity of elastic solutions in ground, such as coal. Particularly under deep cover as is prevalent in the western United States, the coal around a borehole would likely have yielded so that post-yield behavior would govern the response of the instrument.A numerical experiment was conducted by NIOSH researchers using the FLAC software (Itasca Consulting Group, 2016) to investigate the response of the borehole pressure cell (BPC) and the biaxial stressmeter to varying degrees of plastic behavior. The pre-encapsulated BPC cell pressure exhibits increasing departure from the elastic case with decreasing post-peak-strength slope of the stress-strain curve. On the other hand, because the BSM usually provides much more confinement to the surrounding rock than does the BPC, the measurements obtained from the BSM do not depart significantly from the changes in secondary principal stresses and directions as calculated by the elastic solution.INTRODUCTIONSeveral years ago, Larson et al. (2000) described several instruments that NIOSH had used in underground field studies and how to monitor them with dataloggers. This information is still relevant because of the need to understand how excavation affects the stability of mines and thus, the safety of mining personnel. One class of instruments described in that paper includes those instruments that measure change in rock stress. Although several such instruments might be used to measure stress change, the focus of this paper is on two instruments with which NIOSH has had more recent experience—the borehole pressure cell (BPC) (Geokon, 2018a; RST Instruments, 2018) and the biaxial stressmeter (BSM) (Geokon, 2018b). Other instruments, such as the CSIRO hollow inclusion stress cell (HICell) (Earth Sciences, 2019; Worotnicki and Walton, 1976) may be included in future studies.Early studies in the development of the BPC were those of Panek and Stock (USBM, 1964), Sellers (1970), Lu (1984), and Babcock (1986). Babcock’s work is particularly useful, but his setting and testing range was far below what we experienced in the NIOSH study, and it was Babcock’s data reduction scheme from his laboratory experiments that was used to calculate stress change in the NIOSH study (NIOSH, 2019a)."

Jan 1, 2019

By S. D. Thompson, L. Adler

This study reviews and analyzes the empirical methods available for designing the capacities of coal mine gathering belts. The analyses lead to recommendations concerning the application and implementation of each empirical method. Operations research techniques, mainly simulation models, are also briefly mentioned, and a few recommendations are made concerning their selection and application. The objective of the study is to provide a reliable basis for the practicing engineer to properly select, apply, and implement a capacity design method.

Jan 1, 1988

By Ward Sumner

The Jones Hill prospect is a Proterozoic age, volcanogenic, semi-massive to massive sulfide deposit. The deposit is located on the western edge of the Pecos greenstone belt in the southern Sangre de Cristo Mountains of northern New Mexico. The prospect is found in a block (West Block) of meta- igneous rocks, primarily diabase, metavolcanic rocks, and metasedimentary rocks (fig. 1). This assemblage is typical of lithologies found in the greenstone belt. Metamorphic grade is greenschist to lower amphibolite. The West Block is bound- ed on the west by Proterozoic age (1.7-1.4 b.y. by Rb/Sr), granitic plutons collectively called the Embudo granite, and on the east by Paleozoic sedimentary rocks, primarily sandstones, shales, and limestones of Mississippian and Pennsylvanian age. The mineralization occurs in a single horizon which has been overturned and cut into two blocks by a high-angle reverse fault (fig. 2). The mineralized horizon is found at the contact of felsic metavolcanic and rnetavolcaniclastic rocks with overlying intermediate metasedimentary rocks. The local stratigraphic sec- tion from bottom to top is as follows: 1) porphyroblastic quartz- sericite schist (originally a rhyolitic, subvolcanic intrusive); 2) quartz-sericite-chlorite-biotite schist (felsic metavolcanic and metavolcaniclastic rocks); 3) chlorite-talc-biotite-sulfide schist (altered felsic metavolcanic rocks); 4) carbonate-quartz-sulfide [ ] chlorite-tremolite-talc schist (mineralized exhalite); 5) quartz- chlorite schist (silicified tuff); and 6) amphibole-chlorite-feldspar- biotite schist (occasional mafic to intermediate metavolcanic flows).

Jan 1, 2013

By B. Schimm

Improve the mines productivity by simplifying the mining process, for these tasks the Wirtgen Surface Miner offers an attractive alternative. Surface Miners cut, crush and load material in one operation with only one machine. The cutting depth is controlled exactly.

Jan 1, 1997