Search Documents

By J. Wesley Atkins

In considering the importance of lease management and administration, I have decided to approach the topic, Lease Default and Eviction: Action or Reaction, as a three phase presentation dealing with mineral lease administration and management, past, present and future. Though the title may border on the dramatic, it illustrates the real consequences of alternative approaches to property management viewed from my experience in the evaluation, development and implementation of a number of such systems and services in my current position as president of Talco Group Corporation. First, though, let's take a moment and set the stage by giving a few actual examples of why a pragmatic approach is needed in this particular area.

Jan 1, 1983

By W. Jacobi, B. Haider, D. Regulla, J. Huber

[Introductory Remarks] Thermoluminescence (TL) detectors are widely used for the dosimetry of X- and[ y]-rays. Also filter devices for radon daughter monitoring have been developed in which the a activity on the filter was measured with TL-detectors (Breslin et al., 1977). For this purpose normal LiF-tablets with a thickness of 0.4 - 1 mm were used. However the lower detection limit of such TLmonitors for radon daughters is relative high, especially in areas with a high [y]-background, due to the low [a /-y]-sensitivity ratio of such thick LiF-detectors. This [a/y]-sensitivity ratio can be increased if TL-detectors are used whose thickness is comparable with the range of [a]-particles. On the basis of this consideration we have developed a simple light weighted and sensitive TL-monitor for the measurement of the cumulative radon daughter exposure in air. [Description of the "Monitor] The monitor consists of two parts: The sampling pump with the accumulator, and the sampling probe which contains the air filter and TL-detector system. Both parts are connected with a plastic tube. For operation in mines a light weight, portable air sampler with a built-in accumulator (DuPont model 125 and 200, 400 g) is used which enables an adjustable, constant flow rate in the range of 7.5 -12 1/h. These air samplers allow a sampling period of 10 hours before recharging is necessary. For radon daughter measurements in houses this pump is replaced by a larger, netoperated pump with a flow rate of 180 1/h. Figure 1 shows a schematic cross section through the sampling probe whose weight is 40 g. The radon daughters are collected on a hydrophob membrane filter (Sartorius) with an effective filter diameter of 11 mm and a pore diameter of 3 µm; its collection efficiency for radon daughters is [>] 95%. Above the filter the detector system is mounted. It consists of two thin Tm-activated CaSO4-TL films of 8 mm diameter on a Al-carrier foil manufactured by Matsushita Inc., Japan. The thickness of the TL-film is 6 mg/cm2, which is comparable with the range of a rays. The first detector is faced in 3.5 mm distance above the filter; in addition to the ambient y background this detector is exposed to the [a] and ß radiation from the radon daughters on the filter. Between the first and the second TL-detector is an Al-absorber of 0.5 mm thickness which shields this detector against the [a] radiation and partly also to the ß radiation from the filter. Both detectors have the same [y] shielding. After air sampling both TL-detectors are read-out with a commercial, hot-air reader (Matsushita Inc. / Japan, Model 505 A). The glow-curves are identical for [a and y] rays (Regulla et al., 1980). The integral TLsignal from both detectors is displayed in mR-units (or mR-equivalent). The difference between the response of the unshielded TL-detector above the filter and the shielded TL-detector is proportional to the time-integral of the filter activity, integrated over the sampling period. Calibration and Intercomparison Measurements] The linearity of the a response was checked with a 241Am-source for an [a] fluence on the detector surface of 5400 [a's/cm2•s] in the range of 102 -105 mR-equivalent. Within the experimental error of 15% the response function is linear. The TLD-monitor was calibrated for radon daughters in air by comparison with a calibrated integrating, monitor (WLM-meter) equipped with a Si-surface barrier detector and a direct electronic read-out; this instrument was developed by us for area monitoring some years ago (Haider et al., 1976). The results of simultaneous measurements with the TL-monitor and the electronic WLM-meter in mine areas and in indoor air of houses are shown in figure 2. On the abscissa the mean potential [a] energy concentration (in WL) during the sampling period is given which was derived from the measurements with the electronic WLM-meter. On the ordinate the corresponding response of the TLDmonitor to radon daughters (difference between both TL-detectors) is displayed, expressed in terms of mRequivalent per liter sampled air. It follows from this comparison a linear relationship over the whole range of 0.005 - 5 WL with a standard deviation of 10%. The resulting calibration factor for the TLD-monitor is 18± 2 mRequiv per WL • 1.

Jan 1, 1981

By W. Blake, J. Whyatt

Sixty years of rock bursting in the Coeur d'Alene district has taught painful lessons and led to a number of practical advances in controlling rock-burst hazards. This paper summarizes these lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rock-burst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rock-burst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d'Alene district experience.

Jan 1, 2003

By B. J. Arnold, F. F. Aplan

A model incorporating rate and residence time to describe the froth flotation process was used to provide data for the evaluation of various kinetic flotation models and to provide scale-up information from laboratory to industrial scale coal froth flotation. Rate constants were determined in laboratory and plant froth flotation tests and the residence time distribution was measured for a bank of four 21 ft 3 (0.6 m3 ) WEMCO cells treating Upper Freeport seam coal and a bank of four 300 ft 3 (8.5 m3 ) cells treating Lower Kittanning seam coal. It was found that a lag time for continuous flotation should be incorporated into scale up models and that a kinetic froth factor ratio of between about 2.0 and 2.8 should also be used to scale up data from laboratory to plant scale.

Jan 1, 1989

By Rakesh Sehgal, Pushkar Verma, Mohit Sharma

"SJVN Limited successfully commissioned its Rampur HEP (412 MW) in 2014. The project has been planned to operate in tandem by directly utilizing the Tail Water of SJVN’s prestigious Nathpa Jhakri Hydro Power Station 1500 MW located upstream. The initial filling of voluminous water conductor system of RHEP with 10.50 m diameter, 15 Kilometer long Head Race Tunnel, involved more than 1.5 million m3 of water. The filling operation of such a large diameter tunnel constructed in young folded Himalayas which always offer less ideal sites for tunnelling and their subsequent operations under pressurized conditions is worth sharing with tunnelling fraternity. The paper covers meticulous planning, execution, precautions taken, and performance monitoring during filling process keeping in view the fragile geology, low rock cover zones, shear zones in close vicinity of thickly inhabited areas, squeezing zones, hot water zones encountered during excavation.1.0 RAMPUR HYDRO POWER STATION IN BRIEFRampur Hydroelectric Project (412 MW), is located in Himachal Pradesh (India). This project is a downstream development of Nathpa Jhakri Hydro Power Station (1500 MW) constructed on river Satluj and commissioned during 2003. Both the projects today are now successfully working in tandem. The upstream NJHPS has been constructed on the left bank of the river while the downstream Rampur HPS is located on right bank of the river (Figure-1).The major length of HRT of Rampur project lies on right bank of river before it crosses under the river in its initial reach (Figure-2). The main features of the project are as below:• 10.50 m diameter 15 km long HRT ending in a 155.75 m deep, 38.00 m diameter surge shaft.• 3 steel lined pressure shafts, 5.4 m dia, 211-220m long.• Surface valve house 69 m long x 10.50 m wide x 23 m high housing 3 No. butterfly valves• 3 No. surface penstocks 5.4m dia 368-382m long, bifurcating into six penstocks, each of 3.80 mdia. to feed six generating units of surface power house 158 m long x 24.50 m wide x 48 m high, with Francis turbines each of 68.67 MW capacity."

Jan 1, 2016

By R. Mensah-Biney

The loading characteristics of gold-tetrabromide species onto activated carbon have been evaluated using a completely mixed batch reactor system. The overall loading of gold onto carbon was rapid for the first hour but continued slowly without cessation as a result of reduction of gold. Conventional equilibrium considerations were therefore not applicable. Although loading continued slowly after several days, abnormally high loading capacity values of 10-12 meq/g carbon (650-800 kgAu/tonne) could be attained within 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of [AuBr4l-onto the carbon surface where reduction to metallic gold took place. Elution of gold from the loaded carbon was feasible provided the carbon had not been loaded to too high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon is discussed.

Jan 1, 1992

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means of controlling gases and dust. In order to study longwall ventilation in a controlled environment, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers built a unique physical model called the longwall instrumented aerodynamic model (LIAM). The LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel. It has an 8.94 by 4.88 m (29 by 16 ft) footprint with a simulated face length of 220 m (720 ft) in full scale. LIAM is built with critical details of the face, gob and mining machinery, and scaled to preserve the physical and dynamic similitude. This paper discusses the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By Malcolm D. Flavel

Recent research into the mechanisms of crushing processes has led to the establishment of new criteria for the effective design and operation of comminution plants. This paper reviews this work and gives examples of the productivity gains and cost benefits that have been achieved in the practical application of these findings.

Jan 1, 1988

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify, and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multiphase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two-phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone is explored with the aid of both computational and experimental techniques (particle image velocimetry (PIV)). More specifically, the flow field with an air core has been investigated. In addition, the air-liquid two phases flow in a hydrocyclone might cause some challenges on both the computational and experimental sides. Two turbulence models are utilized in the numerical calculations: the Reynolds stress model and large eddy simulation. The computational studies are mainly focused on the local flow behavior and the prediction of the dimensions and shape of the air core. Different section planes of hydrocyclone are selected as planes of interest and divided into several fields of view (FOV) for PIV measurements. Two-dimensional experimental velocity vector maps are obtained in each of the fields of view. The computational results are validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles.

By Ryan C. Stephan, Zach Agioutantis, Christopher Mark

Over the past 15 years, roof fall rates have decreased by two-thirds in U.S. coal mines and by even more in regions where the roof is weakest. This remarkable reduction in the number of roof falls has been accomplished with more effective roof support systems. The purpose of this paper is to present an empirical design methodology that uses real-world data to quantify the basic roof-support concepts that have been successful in the United States. A new computer package, called Analysis of Mine Roof Support (AMRS), implements the design methodology.

By S. Gundiah

Preparation of functionalized polymers from the polymerization of monomers and preformed polymers are discussed with a few illustrative examples. The methods of their characterization, with reference to their application in flocculation, are described.

Jan 1, 1987

By S. Afrouz, C. Keles, W. R. Reed, E. Sarver, T. Akinseye, A. Greth, L. Pan, F. Animah

The resurgence of severe lung disease among U.S. coal miners has not only highlighted the need for improved dust controls, but also the need for an improved understanding of dust characteristics and monitoring strategies [1]. Following up on prior work by the National Institute of Occupational Safety and Health (NIOSH) to demonstrate a novel wet dust collection system on a roof bolter [2], the current study explores the effect of that system on dust characteristics and uses interlaboratory comparisons to comment on analytical methods. Results indicate the wet system did not appreciably affect the composition or size of respirable dust in the vicinity of the operating roof bolter. However, the system does appear to have substantial benefits for the operator. NIOSH has already shown it can reduce the respirable dust mass concentration to which the operator is exposed during dustbox cleanout [2,3], which is a frequent maintenance activity that can re-aerosolize dust, and new results here indicate the silica and silicates content in this dust may also be reduced, thereby reducing the overall hazard. Moreover, regarding analytical methods, excellent correlation was demonstrated between measurements of quartz mass, taken first by NIOSH and then by a university laboratory, using direct-on-filter Fourier transform infrared (FTIR) analysis. This method is the basis for envisioned “end of shift” silica monitoring (quartz is the predominant form of crystalline silica in coal mines) [4]. For particle-level analysis by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), there was more variability in results generated by two independent university laboratories.

Mar 1, 2024

By C. D. Litton, I. E. Perera

This report presents the results of experiments to evaluate different types of mine fire sensors in an underground mine environment using a commercially available atmospheric monitoring system. To determine how well carbon monoxide (CO) and smoke sensors respond for purposes of fire detection, experiments were conducted using test fires of different mine combustibles and for both flaming and nonflaming combustion. The experiments were designed to assess the response of fire sensors to different contaminants and different contaminant levels produced from the test fires. The experiments were performed in the Safety Research Coal Mine at the U.S. National Institute for Occupational Safety and Health’s Bruceton Research Facility in the presence of an average ventilating air velocity of 1.6 m/s (315 fpm). Five fire sensor stations were located downstream of the test fire at fixed locations, with each sensor station consisting of four sensors: a CO fire sensor and three different smoke sensors, of which two were evaluated by the Mine Safety and Health Administration (MSHA) for intrinsic safety and the third was used extensively in underground mines overseas but not evaluated by MSHA for intrinsic safety. All four sensors were mounted near the center of the entry and in the upper onethird of the entry height. A UL-listed combination ionization and photoelectric smoke sensor was mounted near the roof at the first sensor station and its responses were compared against the responses of the four CO and smoke fire sensors. Sensor response data, contaminant travel times, and the impact of fire on the existing ventilation flow are discussed as they apply to earlywarning fire detection. Of significance in the analysis is the need for performance standards for mine fire sensors in order to provide for consistent and timely early warning of developing fires.

Jan 1, 2014

By C. Haycocks

Damage prediction during multi-seam mining is an essential precursor to optimizing mine design. Ground control problems associated with interaction are influenced by both fixed geological and site conditions as well as mining variables which may be controlled to varying degrees. To quantify interaction effects across an affected seam a hazard map approach was selected, which allows interaction data to be presented in a form that can facilitate future planning. Study mines were analyzed using boreholes as sources of geological and spatial data, together with information from mine maps which gives the extent of mining activity. To demonstrate the method the safety factor against interactively caused shear failure in the lower seam roof was computed. Input data included depth of cover, inner burden thickness, remnant pillar size, extraction ratio, immediate roof type, seam thickness, percent sand-stone, and rock strength values. These safety factors were then contoured to produce a hazard map. An assumption was made to assign a high safety factor at the outcrop line to permit realistic contouring of the safety factors. The software also allowed mine workings to be drawn onto the map to facilitate interpretation of the overall results. Hazard analysis permits delineation of unsuitable mining areas within a seam. The application of the method for refining mine design and improving reserve recovery is verified using case studies.

Jan 1, 1992

By Roger Holmberg

INTRODUCTION The driving of drifts is a very important aspect of underground mining. It is not unusual for the percent¬age of rock broken during development in a mine using sublevel caving, for example, to be as much as 25% of the total. If one also considers the amount broken for transport, ventilation, and exploration drifts, one can easily understand that the planning and excavation of drifts play a major part in the total economics of the mine (Fig. 1). Increasing mechanization in mining demands larger tunnel areas for transport and mining equipment. With modern machines the hard work involved in using hand¬held pushers is gone, and a better environment is achieved. More rational methods could be used, but much of the experience the working man acquired by working close to the rock face (such as utilizing the natural weak planes in the rock when he placed the drill¬ing holes) has unfortunately been lost. By having sepa¬rate shifts for drilling, loading, and hauling, more atten¬tion has to be placed upon a well-designed drilling pattern. Some reduction in the number of holes required can be achieved with mechanized drilling because of the larger holes that can be produced. On the other hand, it is probably not possible to achieve the same precision as with pneumatic pushers, and it is difficult to utilize the larger holes because these cause more damage to the re¬maining rock. Recently, however, the precision has be¬come very good with the parallel booms and automatic devices for setting the lookout angle (Fig. 2). A larger arch of the drift roof requires a more carefully executed blasting procedure than before in order to prevent rock fall and to insure a sufficiently long stand-up time. In this chapter, empirical relationships that can be used to design an economic and optimal drift blasting design will be presented. The principles of the calcula¬tion method are based upon the earlier work of Langefors and Kihlström (1963) and Gustafsson (1973). COMPARISON OF EXPLOSIVES To provide for the use of various explosives it is necessary to have a basis of comparison. Several meth¬ods have been developed to characterize the strength of an explosive. Some examples are comparison of values given by (1) calculated explosion energies; (2) the ballistic mortar test; (3) the Trauzl lead block test; (4) the brisance test; (5) the weight strength concept; and (6) the underwater test. However, most of these meth¬ods should be used carefully when stating the breaking

Jan 1, 1982

By M. G. Ayat, B. C. Scott

H. P. Ferri I refer to the article "Degradation Process in Coal Slurry Pipelines" by M.G. Ayat and B.C. Scott in the September 1988 issue of Mining Engineering. I would like to congratulate Dr. Ayat and his colleague on a very interesting and valuable piece of work. This article is an excellent one, describing a real phenomenon that has been ignored for so long. I do, however, have an objection. The article fails to address the degradation process when coal is processed or transported in other ways than slurry form, particularly those employed in this work. Could, for example, screening (wet or dry) have contributed to the extent of degradation? Perhaps scanning electron micrographs of the samples examined and after screening would have helped to clarify this. I would like to point out that degradation is also observed in pneumatic conveying systems, mechanical conveying, and other means of transportations employed by the mineral industry. Reply by M. G. Ayat We gratefully acknowledge Dr. Fern's comments on the subject paper. As he so rightly points out, the degradation process is a real problem, not only in coal slurry pipelines, but also in many handling and processing equipment employed by the coal and mineral industry. Scanning Electron Microscopic examination of samples may offer very little information about the extent of degradation for several reasons. One is that preparing a representative sample that has undergone degradation will be extremely difficult if not impossible. This problem is exacerbated by the fact that SEM requires only very small amounts of material for testing. Secondly, there is a sample preparation step involved in the SEM examination and, as such, it would be very difficult to associate the extent of degradation to either sample preparation or handling and processing operations. Finally, it is probably worth mentioning that degradation is a multi-faceted phenomenon involving many natural and man-made factors. The logical approach to this problem would, therefore, seem to be a "one-step-at-a-time" approach.

Jan 2, 1989

By Franklin H. Sharp

During the last few years the New Lead Belt of South- eastern Missouri has become the main source of lead in the United States. It also produces significant amounts of zinc, copper, and silver. The mines are located on a narrow, mineralized trend extending southward from Viburnum, Missouri for about thirty-five miles. The area is part of the Ozark uplift and consists of steep-sided, heavily wooded hills with narrow valleys. Surface streams are very erratic, normally having low flows but becoming rushing torrents during the violent thunderstorms that occasionally occur. Because of the pristine nature of the country and the newness of the mining developments, the environmental impact of all phases has been closely watched.

Jan 1, 1973

By Claude M. Moreland

It is common practice when thermally drying coal from wet coal preparation facilities that the coarse +0.5mm fractions and fine fractions (-0.5mm) are combined and fed to a thermal dryer. There are very good reasons for this concept. The coal feed is much easier to handle in this condition for it is not as likely to stick inside the dryer or hang up in the material handling equipment, and is easier to feed and discharge. However, it is generally only the -0.5mm fines that really need to be dried. The +9.5m fraction of the cleaned coal will leave the dewatering screens, or drain and rinse screens, at an acceptable surface moisture, probably 5 or 5 ½ percent. The 9.5m x 0.5mm mesh fraction can be centrifuged to about 8 percent. The -0.5m fines can range from 18 to 22 percent or more, depending upon the type of equipment employed to dewater, and upon the size distribution within this size range.

Jan 1, 1982

By D. R. Rice

Separation of valuable constituents from a complex mineral mixture was examined. Nitric acid leaching produced a solution containing copper, zinc, iron and a large proportion of silver. The residue contained antimony, lead, the remaining silver and elemental sulfur. A caustic sodium sulfide leach dissolved the antimony from the residue, producing an insoluble, high-grade silver-lead product and a filtrate for electrolytic recovery of antimony. The pH of the primary filtrate was raised, precipitating the iron and leaving a solution containing the copper, zinc and the soluble portion of the silver, which would be recovered by conventional means.

Jan 1, 1969

By Bianca Cruz, Tom Lankiewicz, Kent Sorenson, Karrie Radloff, Elizabeth Deyett, Dayal Saran, Michaeline Albright, Dan Stigers

Biology opens a new frontier for the mining industry. With rising environmental concerns, the need to couple conventional chemical and physical technologies with sustainable approaches is pressing. At Allonnia, we harness microbial processes to create innovative and environmentally responsible technologies with broad applications. The native microbial community (microbiome) remains largely unexplored at most mining sites, unlike the geochemical environment. The exploration of complex biological reactions that could transform mining technology is just starting and holds vast possibilities, spanning bio-cementation, carbon sequestration, ore beneficiation, water mitigation, bioleaching, metals recovery, and more. Allonnia has collected samples from mine sites in Australia, Africa, and North America to characterize the microbiome and uncover the genetic potential present in mineral-rich environments. We are evaluating microbial metabolites that selectively solubilize gangue from various ores. In addition, biological reactions hold promise as tailings stabilizers. Our early efforts illustrate exciting prospects for harnessing biology’s potential in mining.

Feb 1, 2024