Search Documents

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By I. H. Douglas

All grade control methods in use currently by the mining industry are imprecise. The methods suffer from being locally inaccurate, leading to are loss and contact dilution. An ore/waste indicator variable can be used to predict the probability of ore occurrence at a given location, Po. Then, an ore grade Zo for an ore location and a waste grade Zw for a waste location are obtained. The expected revenue is calculated at each location, based on its probability of being are or waste, the corresponding grade, and on the cost of mining and processing the ore or the waste. Finally, the decision of whether to recover the block is based on the expected revenue value for that block. The method is illustrated with an example taken from the Jerritt Canyon district in northeastern Nevada.

Jan 1, 1994

By D. E. Ranta, M. G. Hester

The ore reserve modelling of stratiform uranium deposits to be mined by selective underground mining methods must be done with consideration of the erratic nature of the ore-forming processes that produced the mineralization. Estimation methods that model the uranium grade as a smooth transition between high-grade and low-grade drill hole intercepts tend to greatly overestimate the ore tonnage. Care must be taken to first establish realtistic ore pod geometries and then estimate the grade of the reserve units within the pods.

Jan 1, 1992

By Goran Mathisson

PLASMARED is a process in which one well established and one new advanced technology have been merged into a practical tool for production of high quality direct reduced iron at lowest energy consumption and costs. Before describing the process, we have to reiterate the simple fundamentals of making metallized iron from iron ores: The main components necessary are: - Iron oxide - Carbon and/or hydrogen - Heat

Jan 1, 1982

By Hans von Michaelis

The renaissance in extractive metallurgical practices for gold and silver recovery is far from over. This is one conclusion of a three year investigation into innovations in Cold & Silver Recovery by Randol International Ltd. (1981, 1983). The six volume reference report reviews a host of new processes and innovative applications of older metallurgical practices. Some of these were summarized by von Michaelis (1982, 1982a). There are several reasons to expect this renaissance to continue. One reason is the nature of gold and silver deposits. The list of known occurrences of These metals is very extensive. There are literally tens of thousands of prospects but over 99% of these are too low grade, too small or too refractory for a viable operation employing conventional processing.

Jan 1, 1983

By S. C. Termes

As part of an effort to provide basic data on the fundamental scientific and engineering principles of minerals beneficiation, the Bureau of Mines is conducting research on the flocculation of mineral fines. This paper presents results of studies using crosslinked starches containing carboxyl, diethanolamine, iminodiacetic acid, and xanthate groups to flocculate hematite, goethite, chromite, manganrte, pyrolusite, cuprite, and cassiterite fines. The carboxyl and xanthate derivatives flocculated all minerals except cassiterite; the latter was flocculated by only the diethanolamine derivative. The iminodiacetic acid derivative flocculated hematite, goethite, chromite, cuprite, and pryolusite fines. Zeta potential measurements were made to help define the reaction mechanism responsible for flocculation. These measurements indicate that electrostatic attraction probably is not involved, except possibly in the case of the diethano lamine derivative. The separation of hematite from quartz by selective flocculation with chelating cross- linked starches under two pH conditions and with two dispersing agents is described. Best recoveries and grades were found when either the carboxyl or xanthate derivatives was added at the natural pH of the pulp in the absence of a dupersing agent.

Jan 1, 1983

By D. J. Rose

The San Miguel Mine is owned by San Miguel Electrical Cooperative, Inc. and operated by Atascosa Mining Company, a wholly-owned subsidiary of Morrison-Knudsen Company, Inc. This multiseam, single-zone lignite surface mine is located near Jourdanton, Texas, 110 kilometers (68 miles) south of San Antonio. Lignite extracted from four closely-spaced seams is used to fuel the 400-MW San Miguel Power Plant. Recovery depths range from 7 to 37 meters (25 to 120 feet). The mine began stripping operations in the spring of 1980 and now produces approximately 2.5 million tonnes (2.8 million tons) of lignite annually. Atascosa Mining Company is responsible for production, maintenance, engineering, and management services. Production responsibilities include topsoil removal, overburden removal, lignite mining, spoil pile regrading and topsoil replacement, as well as ash disposal and construction and maintenance of water retention and diversion facilities.

Jan 1, 1984

By Chris Roos

The mining industry has made strides in planning for operations to be safe for the workforce and public, to protect the natural environment, and to maximize value for shareholders. However, many of the techniques used to accomplish these goals are based on estimated models of mineral content, production efficiency, and economic performance. The industry has begun to recognize the need for understanding the uncertainty in these models, how it affects their decisions, and what the potential impacts are for each project. The challenge has become how technical professionals can effectively communicate the impact of this uncertainty and its importance to both technical and non-technical audiences. This paper presents mining engineers (and other technical professionals) with traditional and modern principles of data visualization and technical communication that can assist with communicating the effects of uncertainty in the mine planning process.

Jun 25, 2023

By F. Ysla, M. Mendoza

This proposal, based on the CIEMAN Cajamarca - Hualgayoc initiative, focuses on “Transforming Abandoned Mine Lands’’ We aim to study and assess the feasibility of an innovative rehabilitation method. Contaminated soils will be moved from the upper to the lower site, encapsulated with geosynthetic barriers, and covered with topsoil. The decontaminated upper area will be used for planting trees and large-stemmed plants for hiking and tourism, while the lower encapsulated area will support livestock and short- stemmed crops. This study will evaluate the economic viability and multi-use potential of this technique, promoting sustainable land recovery in Cajamarca, Peru.

Feb 1, 2025

The exploitation of mineral deposits for economical recovery of the contained minerals has many aspects differing from other industrial or manufacturing operations. However, generally accepted principles of good organization and management applicable to industrial plants are similarly effective for mineral processing plants. A more detailed coverage of organizational structures and management techniques than is possible in this section can be obtained from many good books devoted wholly to these subjects. A few of the more readily available examples are included in the general references at the beginning of this section. The field of mineral processing encompass a wide variety of minerals, processes, flowsheets, equipment, and end products. Mineral deposits, mines, and related beneficiation plants are found in all parts of the globe, often in remote locations with no nearby support for supplies and maintenance. Available labor is frequently unskilled, sometimes primitive, and often untrained without machine and hand tools or heavy equipment experience. Such situations call for well- planned and conducted training programs covering the full range of mining-type job skills. Climates can range from arctic to tropical and from arid to extremes of rain or snow, and the mine and plant sites can be almost anywhere. However, it is often possible and sometimes necessary for

Jan 1, 1985

By C. Perea, O. Restrepo, C. Ihle, H. Estay

In this study, research on the use of monosodium glutamate for copper leaching, with emphasis on the thermodynamics and oxidant characteristics, is presented. Copper dissolution was conducted following a hydrometallurgical route, using monosodium glutamate in alkaline solutions. The effect of oxidizing agents such as hydrogen peroxide (H2O2) and potassium permanganate (KMnO4), and the efficiency of copper leaching with glutamate compared with glycine have been studied. Results, obtained at room temperature, showed 92% recovery of copper using 0.03 M hydrogen peroxide, 0.5 M monosodium glutamate at a pH of 9.44.

Mar 2, 2022

By Mahmut Altiner

Magnesium is listed as a key critical raw material in a report by the European Commission that evaluated raw materials based on supply risk versus economic importance [1]. It has extraordinary properties, such as nontoxicity, inertness, high melting point, stability, low weight, chemical resistance, electrical insulation, optical transparency, corrosion-resistant behavior and refractory nature. It is widely used in the areas of agriculture; the environment, for antibacterial and water-purification purposes; electronics; automotive; drug delivery; ceramics; construction, as filler in brick; and concrete production, in the forms of magnesium oxychloride and magnesium oxysulfate. Magnesium oxide (MgO) particles can be produced through the calcination of magnesite ore at different calcination conditions depending on the desired quality of the product, classified as fused (2,800 °C), dead-burned (>1,400 °C), hard-burned (1,000–1,400 °C), or light-burned MgO (700–1,000 °C) [2]. However, the global availability of magnesite ore is limited.

By Francesco Chiappalone, Miriam Piemontese, Lance Waddel, Paolo Perazzelli, Emidio Tamburri, Roberto Schuerch

The Three Rivers Protection & Overflow Reduction Tunnel is part of the Long-Term Control Plan of the City of Fort Wayne, Indiana (USA). The 4.9 m internal diameter tunnel, of length approximately 7.5 km, is excavated at a depth of approximately 40–60 m through carbonate rocks using a slurry TBM. Due to the high hydraulic conductivity of the rock mass and the high in-situ ground water pressure (up to 6.5 bar), the management of the water inflow during the TBM advance and standstills, represents the major challenge for the project. This paper outlines the geotechnical conditions and the hazards related to the large water inflows expected in the pre-excavation phase and discusses the experience gained during the construction of the first 8,224 feet (2,507 m), (first third of the total length of the tunnel).

Jun 13, 2021

By S. Su, S. Natansohn

This report describes a process for tungsten recovery from Searles Lake brines and upgrading its concentration to useful levels. The method consists of a combination of a liquid-solid and liquid-liquid extraction step and results in a product stream containing more than l00g W03/1. This technique is also effective in substantially reducing the concentration of objectionable impurities in the tungsten product. An ion exchange extraction mechanism is postulated.

Jan 1, 1983

By Ehsan Nasiri, Keivan Pak Iman

Historically, boulders are a frequent source of problem in soft ground tunneling. It is important to attempt to make an assessment of the nature and quantity of the boulders, although in many cases, it will be impossible to do so with great accuracy. Boulders, can pose major problems for TBMs in terms of slowing down or halting the tunnel advance, cutter damage, and abrasive wear. Although proper selection of the TBM and the cutterhead can reduce the risks, ground uncertainties still cannot be eliminated. The paper reviews a case study of a 3480 mm diameter EPB-TBM in Toronto utilized for completion of 2.5 km tunnel in Glacial Till, crossing the CP railway, HWY 401, a creek, and a confined aquifer. Alignment consists of multiple horizontal curves including small radius curves (r=210 m) at shafts breakthrough. An unexpected boulder cluster lead the contractor to experience extreme damages to the screw conveyor, RFJ system and causing a crack in main motor plate which resulted in losing one of the six main motors. This paper reviews contractor’s solutions and includes discussion on specific claim resolution method used in this project that can be of great value in preparation of specification and GBR for similar projects.

Jun 13, 2021

By I. Melik-Gaykazov, N. N. Melnikov, V. A. Fokin, S. P. Reshetnyak

Kola Mining Institute has been carrying out investigations of the possibility to steepen the walls of the Kovdor open pit with the design depth of 600 m. Steeping (up to 60°) wall angles is done by double height (24 and 30 m) benches with vertical slopes. One of the safety factors of mining with such walls is choosing the width of the safety berms preventing against rock falling from the slopes into the pit working area. The test on rock falling from 24 m benches has shown that vertical slopes are not more dangerous compared to the inclined(60-75°) ones.

Jan 1, 2003

By J. García, B. Arango, F. Calderón, O. J. Restrepo-Baena, A. Carreno, L. Rojas-Mendoza, J. Pérez, E. Bedoya

"Tungsten extraction is a subject of global interest due to is properties. These properties, such as its high melting point, have contributed to the development of metallurgical extraction processes that can be adapted to the particular chemical composition and mineralogy of the ore. In Colombia there is a research deficit in tungsten related areas, and especially with regard to its extractive metallurgy. In this study the physical, chemical and mineralogical characterization of a sample were performed. Subsequently, crushing and grinding were employed to reduce the material to a more convenient size, making it suitable for further concentration and metallurgical processes. Through physical concentration techniques it was obtained a concentrated ranging between 60 -70 % of WO3 content.INTRODUCTION Tungsten is a metal of great economic importance due to its excellent properties such as high density and extraordinary melting point 3422°C), which is indeed the highest of all the elements. Tungsten is primarily used in metal alloys, manufacture of special steels, coatings and catalysts; products of interest to both international and national industry. However; given that the use and economic value is determined by the percentage of tungsten in the mineral, particle size and chemical associations, it becomes essential to properly characterize the mineral to further define possible metallurgical extraction routes. The metallurgical processes for minerals enriched in tungsten may vary depending on location and the genesis of the ore body, which means that for each ore a particular set of operating conditions must be determined. This is important since process standardization can lead to misuse of the mineral resource. However, in Colombia there is a research deficit as it relates to minerals enriched in tungsten and to its extractive metallurgy. Then, there is a need to conduct studies that can lead to a better understanding of the ore, and to develop extraction processes for the metal of interest. EXPERIMENTAL A state of the art review was made in order to gain insights of the tungsten metallurgical process. Comminution was necessary with the aim to reduce the sample size; therefore the sample was taken into crushing and grinding stages. Concentration techniques such as magnetic separation, gravity and / or electrostatic were also applied. Physical, chemical and mineralogical characterization were performed by using polished sections, grain size determination, X-Ray Fluorescence (XRF) and X-ray diffraction (XRD) techniques."

Jan 1, 2015

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION This method is a variation of cut-and-fill mining where either the wall rock or the vein is too unconsolidated to permit safe mining by conventional cut-and-fill methods. Basic development consists of driving a 2.4 x 2.7-m (8 x 9-ft) haulage heading laterally in the footwall side of the vein. Crosscuts are driven over to the vein at 91-m (300-ft) intervals. Then the vein, at each inter¬section, is mined out to a distance of about 9 m (30 ft ) above the track level. After the installation of an ore chute, scrams or intermediate drifts are driven in both directions along the vein. Mining then starts imme¬diately below the level bounding the upper limit of the stope. A cut varying between 3 and 4.2 m (10 and 14 ft) in depth and mined for a distance of 45.7 m (150 ft )along the strike is taken from the orepass in each direction (Fig. 1). In this mined-out void, the floor of the cut is equipped with 203 x 203-mm (8 x 8-in.) caps hitched into the wall with steel saddle hitches installed on 1.5-m (5-ft) centers. Double wood stringers, 152.4 x 152.4 mm (6 x 6 in.), are then installed on 1.2-m (4-ft) centers longitudinally down the length of the stope. Reinforc¬ing wire mesh is also placed, overlying each mat of timber. Directly above the stringers, stulls are installed from hanging wall to footwall to hold the timber in place during the sand-filling operation. Then a cement¬sand mixture in a ratio of about 1:10 weight is poured to a depth of about 2.4 m (8 ft). The entire cycle is then repeated down to the scram drift. Another variation of timbering is illustrated in Fig. 2. There is a vein width of approximately 5.5 m (18 ft) with the same unconsolidated ground conditions. The primary difference between handling this situation and the previously described undercut-and-fill method is that standard timbered sets are installed in each excavated stoping void rather than stulls. Once again the basic method is to work down the ore block from an upper timbered drift to a lower timbered drift. Cuts are taken from a timbered raise with a chute on the stope side. Each piece of ground excavated is essentially two sets high, 5.5 m (18 ft), by two sets wide, 5.5 m (18 ft), by the length of the cut along the strike of the vein. The timbered sets are 2.4 x 2.4 x 2.4 m (8 x 8 x 8 ft). The net result is, therefore, two sets of timber on a top floor separated by doubled-up 76-mm (3-in.) lagging from

Jan 1, 1982

By William H. McLemore

Geologists searching for carbonate rocks suitable for chemical uses traditionally have relied on extensive laboratory testing in order to locate strata or zones that might be suitable for mining. However, when considering the significant time and costs involved in sampling and performing chemical analyses, any exploration technique whereby fewer samples and analyses are needed would be of great value. In other words, if the exploration geologist could "zero-in" on select areas, considerable time and money could be saved. In general, the major-element chemistry of carbonate rocks is determined by the abundance of the minerals present. CaO occurs with CO2 as the mineral calcite, which is the primary mineral comprising allochems, matrix and sparry cement; MgO is found in high-magnesium calcite (many calcite fossil species contain appreciable amounts of MgO in solid solution), dolomite, and chlorite; iron occurs in pyrite and in limonitic stylolites, as well as in chloritic and glauconitic clay minerals; materials containing abundant Si02 are microcrystalline quartz (chest) silt-sized quartz, and clay minerals; and Al203 is found primarily in illitic, kaolinitic, and chloritic clay minerals. The presence or absence of these minerals determines the chemical composition of the carbonate rooks.

Jan 1, 1983

By Cristian Saavedra, Patricio Zarate

Flotation collectors play a crucial role in mineral flotation by selectively adhering to mineral surfaces and aiding in their separation from gangue material. They are heteropolar molecules, as defined by Sutherland and Wark (1955), featuring non-polar hydrocarbon chains and polar groups interacting with mineral surfaces to induce hydrophobicity selectively. The importance of collectors in mineral processing, as underscored by Lotter and Bradshaw (2010), lies in their ability to enhance recovery rates and improve selectivity, thereby optimizing the extraction of valuable minerals from complex ores. Collectors are classified based on their mechanism of action, as proposed by Laskowski (2010). This classification categorizes collectors into three groups: water-soluble compounds, water-insoluble “oily” collectors, and water-insoluble amphipathic compounds forming molecular films at the water/gas interface. This complements the chemical structure-based classification by Sutherland and Wark (1955) and Suoninen and Laajalehto (1993), offering a comprehensive understanding of collector diversity in flotation systems. Collector selection is an iterative process crucial for optimizing mineral processing efficiency, as emphasized by Lotter and Bradshaw (2010). Understanding the significance of collector mixing or synergy outcomes is paramount for enhancing mineral flotation efficiency and sustainability. Taguta, O’Connor, and McFadzean (2018) demonstrate that mixed collector systems enhance interaction enthalpies and microflotation recoveries, indicating improved performance. McFadzean, Castelyn, and O’Connor (2012), along with Critchley and Riaz (1991), delve into investigating synergistic interactions between collectors, offering insights for strategic selection. Observations from the study of collector synergy, as noted by Wakamatsu et al. (1980), reveal nuanced relationships surpassing individual collector behaviors. The methodology outlined in this paper provides valuable guidance for classifying and selecting collectors based on specific application needs, while also suggesting the potential for synergistically improving recovery across fine, intermediate, and coarse particles.

Feb 1, 2025