Search Documents

By Barry A. Hillman

Respirable (PM-10) crystalline silica is regulated by the State of California as a carcinogen. The risk-management of this material by the State exemplifies the inherent problems in the development of regulations based on current risk-assessment practices. The influence of extremely conservative risk-assessment and risk-management can be expressed in economic impacts including the increased cost of production, reduced competition, increased prices, reduced employment and redistribution of income. This paper attempts to contrast theoretical risk- assessment and risk-management with current application using crystalline silica as an example. Based on health information pertaining to silica, the paper examines federal and State of California regulatory and public policy positions. Using current risk factors and empirical data for the Central Valley of California, the projected incidence of lung cancer in humans is examined. While such an analysis would project an extremely high incidence of lung cancer as well as silicosis, not a single case of either lung impairment has been recorded within the study area or throughout the world in the general population. This suggests that sound guidelines for the analysis of scientific information have given way to the assumption that virtually any information representing a substance as a carcinogen is to be considered valid with little or no qualification.

Jan 1, 1992

By S. Frimpong, G. Galecki

Dump truck tires are often used in long-haul roads in rugged terrain, with high rolling and grade resistances. These conditions increase the ton-kilometer-per-hour (tkm/hr) or short-ton-mile-per-hour (stmph)rating of tires, leading to tread wear, cuts and complete failures. The load-bearing capacities of these tires are sometimes exceeded, with truck overloading, overstressing, heating and subsequent failures. In addition, truck tire demand far exceeds the current supply capacity, with long lead ordering time. This condition has caused severe tire shortage, and the problem is expected to be sustained in the long-term. Industry has taken extensive practical measures to prolong tire service life with significant results. However, this problem can be solved through fundamental and applied research initiatives. This paper pioneers a research effort in tire service life using multibody physics, fatigue failure modes and soil failure dynamics to develop tire-road contact force dynamics. A virtual prototype simulator of the tire-road contact, using the CAT 775E (with standard tire 24.00R35) was developed and simulated within the MSC.ADAMS/NASTRAN environments. The results show the areas of the loaded tires with maximum Von Mises, principal and shear stresses, which could result in fatigue failure, tire wear and tear and blowouts. The maximum Von Mises stresses on the six truck tires are between 35 and 58 MPa. The maximum shear stresses are also between 19 and 33 MPa. These stresses will cause early tire failures given an average operating schedule of between 20 and 24 hours per day. The isolated areas with maximum stresses will be subjected to further studies to reduce stress intensity while preserving tire performance.

Jan 1, 2012

By E. B. Fitch, D. A. Dahlstrom

Liquid-solids separation is common to practically all mineral and coal processing as the bulk of beneficiation plants employ water as the major processing vehicle. The growing usage of hydrometallurgy has increased the importance of liquid-solid separation as acidic and basic solutions result in greater amounts of colloidal solids, with their consequent greater difficulty of separation, the economic need for chemical recovery to minimize this operating cost, and the usual necessity of employing more costly construction materials. The three processing steps covered in this section have significant capital costs. Drying, particularly, has an important operating cost because of the obvious need for energy to evaporate the water or solvent. Several common factors influence all three liquid-solid separation steps. Particle Size and Size Distribution. In general, finer particles have slower settling and filtration rates. The specific surface area is increased, which means a lower solids concentration in the thickener underflow and discharged filter cake as well as a grater moisture content to be evaporated in the drying step. Therefore, overgrinding or excessive attrition should be avoided. Consideration should be given to optimum particle size consistent with entire plant operation performance and recovery. Solids Concentration. Increased feed solids concentration will generally minimize required equipment size and costs in all three liquid-solid separation steps. Most thickeners are designed on the basis of unit area required, expressed as square feet per short ton of dry solids per day (square meters per metric ton per day) which will usually decrease with increased feed solids concentration. Filtration rates also increase as the required flow through the capillaries of the filter cake decreases. Dryer capacity increases and less energy per ton of final product is required to evaporate the associated moisture. Particle Shape and Surface Characteristics. Generally, optimum shape is a spherical particle of zero porosity. As either of these factors degrade away from the desired state, difficulty increases. This is particularly true in drying, where porosity can decrease drying rate significantly if the moisture must first reach the particle surface by diffusion

Jan 1, 1985

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities, or 82 percent, may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible.

Jan 1, 2016

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral-processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. When a sensor goes off calibration, it results in errors that can have a severe impact on plant economics. Classical statistical approaches fail to detect when errors are “subtle,” unless they grow and become large enough to be “gross,” whereas methods based on signal processing and artificial intelligence fail in dealing with the complexity of process fluctuations. Due to the sheer volume of sensors, undetected errors are not remedied until the next calibration, which on average are a year apart across all industries [1]. This research aims to detect such subtle errors (2 percent bias) in shorter time spans of about a month — rather than wait for errors to grow — using innovative data-mining techniques and algorithms.

By Francis B. Gularte, James E. Monsees, John-Paul Whyte, Gary E. Taylor

In a short section of the Los Angeles Metro Rail system approximately 222.5 m (730 ft) of 6.4 m (21 ft) diameter twin-tube tunnels separated by a 1.8 m (6 ft) narrow pillar were designed to pass under a major eight lane freeway and a metropolitan intersection with only 3.7 m (12 ft) to 5.8 m (19 ft) of loose fill and alluvium cover. The design considerations and the chemical grouting program used to stabilize the alluvial materials is discussed. Also included is a discussion of the novel shield used for tunnel excavation and the effects of the subsequent fire.

Jan 1, 1991

By Kevin Sharman, Peri Mehling

A detailed assessment of acid rock drainage (ARD) potential was conducted at the Quintette Coal Mine site in northeastern British Columbia The site is unusual in that the coal seams contain low sulphur levels as compared to eastern coals (typically less than 0.5%), and the non-coal wastes generally do not to have the potential to generate acid on the basis of static ABA tests. The presence of small iron-stained seeps on the pit walls indicate localized sulphide oxidation, while the overall mine site drainage has remained of excellent quality with extremely low levels of metals after approximately 15 years of mining. Thus the site provides an excellent comparison to more problematic coal mine sites. For the Quintette assessment, static acid-base accounting (ABA) analyses of individual samples were compared to criteria for potentially acid generating materials developed for the U.S. Appalachian coal, as well as criteria developed in British Columbia for hard rock mines. Geologic units were characterized by the percentage of samples, or weighted thickness, that was deemed potentially acid generating (PAG). Links were then made to actual seepage and water quality emanating from geologic units around the site. Seeps at the site demonstrate a large range in pH (2.32 to 8.18). The few acidic seeps (pH < 4.0) were found to contain elevated levels of sulphates, dissolved iron, manganese and aluminum, consistent with the metals typically of concern in Appalachian coal mines. Other heavy metals that were detected in acidic seeps at Quintette included copper, zinc, nickel and cadmium. The use of simple ABA tests, and comparison of individual sample results with the Appalachian and British Columbia criteria, was found to be useful in predicting the probable sources of the small localized acidic seeps.

Jan 1, 2000

By John W. Carson, David S. Dick

The last few years have produced new methods of characterizing flow properties of bulk solids. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field condi¬tions. In addition, the effect of large par¬ticles on a material&apos;s flow properties (cohe¬sive strength, bulk density, wall friction) can be determined as well as the effects of var¬ious additives such as freeze conditioning agents. New developments have occurred with devices to improve the reliability of solids flow. Much attention has been paid to find¬ing ways, by using inserts, to provide a mass flow pattern with relatively shallow hopper walls. Such devices can also provide reli¬able in-bin gravity blending of bulk solids or completely nonsegregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. The technology and hardware for running bench scale flow tests on bulk solids samples and transforming the results into reliable designs has been in existence for nearly 30 years (Jenike, 1964; Marinelli and Carson, 1986). It has been shown repeatedly that reliable materials handling systems can be designed to avoid the problems of no-flow due to arching or rat-holing, erratic flow, segregation, loss of capacity, or spontaneous combustion. Running flow properties tests and carefully designing a bulk handling system are not expensive, particularly when compared to downtime costs and continual flow problems. New developments in characterizing flow properties of bulk solids include: • a shear tester for measuring the properties of run-of-mine ores containing large par¬ticles; • attrition testers to simulate a wide range of flow conditions; • a tester to measure the wear rate of liners in bins, feeder parts, etc.; • a dustiness tester to measure the potential for dust and the effect of dust control meas¬ures; and • techniques for measuring the strength of frozen ores and the effect of freeze condi¬tioning agents. In the area of improving the flow of bulk solids, there are new techniques for ensuring reliable flow without using up excessive headroom. These include: • belt-to-belt transfer chutes to handle po¬tentially sticky, abrasive, and dusty ores; • designs for the interface between a bin/ hopper and apron or belt feeders to avoid hangups and minimize feeder loads; methods to feed solids reliably into a pres¬surized process; and designs for handling systems that will mini¬ mize attrition, avoid segregation, or auto¬matically blend materials together. Characterizing flow properties Large shear cell It has long been known that the cohesive strength of a bulk solid is due mainly to its fine fraction. However, the effect of the larger particles (that were assumed to re¬duce the strength) could not be measured. The development of larger scale (205 mm¬diam and 0.6 x 0.9 m or 8 in.-diam and 2 x 3 ft) shear testers has made it possible to measure the properties of a wider range of materials. Now cohesive strength measurements can be made with up to 100 mm (4 in.) particles. The results obtained from the large shear testers, together with the results of the nor¬mal shear tests on the fine fraction, are used in the design of reliable stockpile reclaim systems and crusher feed systems. A high percentage of large particles can reduce the measured shear strength of a bulk solid. However, segregation may alter the size distribution and should therefore be considered (Carson, Royal, and Goodwill, 1986). In addition, larger particles will

Jan 1, 1989

By Nathaniel Arbiter

The question of automation of concentrator operations with computer control is under increasing consideration. Some of the problems involved will be discussed from the viewpoint of the availability of the requisite, detailed knowledge of the unit operations. The justification for full-scale automation of a mill must ultimately be economic--an increase in profitability over and above the cost of instrumentation and development, Potential savings would be in three probable directions: decrease in operating labor costs by substitution of machine control; improved metallurgy through continuous effective control; and decreased operating costs by achieving higher unit capacities and process efficiencies.

Jan 1, 1962

By N. Economou

Temporary local seismic networks were installed in western Crete, in central Crete, and on Gavdos, an island south of western Crete, in order to image shallow seismically active zones of the Hellenic subduction zone. Data acquisition was divided in four campaigns through the years 1996 to 2001. More than 4000 events in the magnitude range between 0.5 and 4.8 were detected and localized. The resulting hypocenter distribution allows the localization of seismically active zones in the area of central Crete from the Mediterranean Ridge to the Cretan Sea. The comparison of the hypocenter distribution and the structure has allowed intraplate and interplate seismicity to be distinguished. A southwards dipping zone of high seismicity within the Aegean lithosphere is found south of central Crete in the region of the Ptolemy trench. Between 20 and 40 km depth beneath central Crete, the Aegean lithosphere appears to be seismically inactive. Especially for the year 2001, 1560 events were localized, by the seismic network installed on Messara, central Crete. Most of the seismic events were located, as expected, in the South region of central Crete. National Observatory of Athens (NOA) maintains a permanent seismic network in Greece. In this work a comparison of the earthquake epicenters obtained from both the NOA network and the BOCHUM-TUC network is presented.

Jan 1, 2006

By James R. Jones

The tempo of air pollution control regulations has increased dramatically in the past few years. Because coal mining operations are frequently located in remote areas away from urban developments, specific regulations applying to coal mines have received lower priority and are thus only now being promulgated and/or enforced. Therefore, many mine operators are not yet familiar with the regulations and the impact upon their method of operations. Few have been faced with an inspector on the property sighting them for specific violations. Several of the Mid-western states are just now requiring permit applications to be submitted.

Jan 1, 1973

By J. A. Herbst

Mineral liberation modeling can be traced back to the early work 0fA.M. Gaudin up through more recent population balance modeling by R.p. King, J.A. Herbst and G.T. Adel. A more micro-scopic look was taken at the University of Utah in the form of the J.E. Sepulveda and J.D. Miller Pargen model which permits the creation of an arbitrary shape, multiphase particle made up of discrete grains. Recent work on image analysis and tomographic analysis by J.D. Miller and C.L. Lin have laid the experimental ground work for model validation, but until now it hasn&apos;t been possible to include the necessary physics of the particle stressing process to allow the development of a &apos;ffirstprinciples"mode1 which does not presuppose a "mode” of liberation (e.g., random or by detachment). Recent developments in discrete grain breakage (DGB) modeling now make a generalized physics based model feasible. This paper describes current work that is being done to develop a physics based discrete grain liberation (DGL) model. Two-dimensional and three dimensional simulation results exploring the effects of particle size, phase properties and loading type are presented. Relationships between energy based liberation efficiency, degree of random liberation and material properties are identified.

Jan 1, 2005

By Hugh Douglas

This paper discusses the financial health of the U.S. mining industry and its ability to meet the future raw material requirements of this country in the context of resource independence. The title of this paper begs several questions, and three will be raised here. The answers to them will form the basis for discussion. The three questions are: What does one mean by resource independence. How is the U.S. mining industry defined. How is financial health measured.

Jan 1, 1977

By Dennis Asmussen

The peatlands of the U.S. and Canadian parts of the Upper Great Lakes region have a long history of modest utilization in agriculture, forestry, horticulture, and as natural undisturbed areas. Only recently have they been assessed as potential sources of non-renewable or renewable energy. This new interest in peatlands, should current proposals be realized, might mean the commitment of millions of acres to energy production purposes. The magnitude alone of this potential utilization of peatland signals the possibility of substantial environmental disturbance, local resource shortages, resource use conflicts, and social and economic change. Peat- land resource managers in the region are just beginning to weigh the advantages and disadvantages of large-scale peatland utilization. The Minnesota Department of Natural Resources has made a considerable effort to study peat resource management issues and will shortly make recommendations to the state legislature regarding utilization alternatives. What follows is a general discussion of peatland utilization and management trends in the region with a focus on Minnesota and its peatland management efforts.

Jan 1, 1980

By R. J. Sheets

"What is the primary responsibility of geo-engineers in mining? Early in my career, I was asked this question by an experienced engineer. After explaining some various tasks, I was informed that the main responsibility was to monitor. Although this proved true for many cases, I came to understand that monitoring is merely one means to achieve the primary responsibility of a geo-engineer — ensure the safety of all personnel. The potential for groundwater to impact stability allows this responsibility to be shared with hydrogeologists as well. Inherently, we monitor to identify risks; we analyze designs and develop models to mitigate risks; and we are provided opportunities to explain to supervisors the geo-risks to personnel and mine plans that will result from particular courses of action. A couple years ago, I took an opportunity to share experiences from the first several years of my career as a geotechnical engineer with junior geoengineering staff within my company. The intent was to share situations that were a part of my development, so they could learn and understand their responsibility to the safety of all personnel. Similarly, the purpose of this article will be to share these thoughts with new geo-engineers in the industry in order to help prepare them for the challenges they will face.What is our purpose?A senior hydrogeologist shared an experience that occurred in their career. The experienced hydrogeologist had spent some time with the hydrogeology staff, most of them relatively new to the mining industry, to understand how they viewed, and carried out, what they perceived as their responsibility at an active mining operation. After a couple months of observing and mentoring, the senior hydrogeologist met with everyone and posed the question “What is our purpose?” I am sure that most junior geo-engineers would start explaining different tasks or projects that they must complete. The list would include monitor ground water levels, track slope movement, evaluate designs, build models, oversee drilling programs, etc. These individuals did as well their supervisor. After going around the room allowing each individual to answer, the experienced hydrogeologist provided them the real answer to the question: Safety. If you examine the root intent of nearly every responsibility geotechnical engineers and hydrogeologists have, it is to apply our professional skills to ensure the safety of our workforce. When the objective of safety from the geotechnical and hydrogeology disciplines is achieved, inherently accomplishing the mine plan should follow suit, or it should significantly minimize the impact by gravity or ground water."

Jan 9, 2018

By V. Nasri, S. Rashidi

The Baltimore Red Line Project is a proposed 22.7-km (14.1-mile) long east-west light rail transit (LRT) line envisioned to connect the areas of Woodlawn, Edmondson Village, West Baltimore, downtown Baltimore, Inner Harbor East, Fells Point, Canton and the Johns Hopkins Bayview Medical Center Campus. The Red Line LRT System has two tunnel segments - the Cooks Lane Tunnel (CLT) and the Downtown Tunnel (DTT). The CLT segment is roughly 1,920-m (6,300-ft) long. It commences at the west portal located at the highway ramp for I 70 (to be removed) and terminates at the east portal that is at the intersection of Edmondson Avenue (U.S. Route 40) and Glen Allen Drive. This segment of the project consists of the following construction components: approximately 1,458 m (4,786 ft) of tunnels, 143 m (469 ft) of cut-and-cover tunnel, and 318 m (1,045 ft) of retained cut (U) section. The approximate horizontal alignment for the Red Line LRT Project is shown in Fig. 1.

Jan 1, 2014

By Rick Wright, Gregory L. Raines

San Diego’s need to access underground space has dictated a long history of tunnel construction. The subsequent need for water, coupled with San Diego’s natural attractiveness, has led to significant population increases and the need for the construction of even more tunnels. This paper will provide a historical summary of the progression of mines, tunnels and trenchless technology construction projects that contributed to the advance of current technology, feasibility, and constructability. A bibliography of relevant reports and data is included.

Jan 1, 2001

By R. J. Gray

Oxidation of coal can best be described as a process of deterioration, since most of the uses of coal, such as for fuel and by-product chemical and coke production, are adversely affected by coal oxidation, and the inclusion of oxidized coal in most coal products detracts from their value. There are probably many mechanisms of coal oxidation, and the ways oxygen molecules combine as complexes with coal macromolecules to form new substances have been dealt with and speculated upon by many workers1)* but are not dealt with in the present work. This study deals with tests and methods of detecting oxidized coal, with particular emphasis on the microscopically discernible changes that accompany the chemical and physical changes that affect the technological properties of coal during oxidation.

Jan 1, 1974

By K. Katen

In another situation, Dave Zegeer, the Assistant Secretary of Labor for Mine Safety and Health, whom all of you know very well, would have taken the opportunity to talk with you. In his absence, however, I would like to reference some of his recent comments which may help us to see the issue of mine safety in historical perspective. Dave pointed out that this year is the eightieth anniversary of the Great Earthquake and Fire of San Francisco. The whole world heard about that disaster--it and the 452 people who died in it. In that same year, nearly five times as many people died in coal mines, but no one particularly noticed.

Jan 1, 1986

By Z. Abdel-Khalek, Hassan El-Shall, S. Farrah, C. Boice

Selective adsorption and surface modification of minerals by surfactants is the primary step in the process of separating certain minerals with similar physical and chemical characteristics in the flotation process. In this study, microorgan- isms are used as surface modifiers for francolite and dolomite. Results of adsorption experiments with francolite and dolomite show that the microbes selectively adsorb to one of the minerals under specific operating conditions. In preliminary flotation experiments, it is found that the microorganisms enhance or depress flotation of the minerals leading to an increase in the efficiency of separation between the francolite and dolomite. The conditions leading to selective adsorption (surface modification) and subsequently to possible efficient separation of these two minerals are discussed in this paper.

Jan 1, 2002