Search Documents

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By Henry E. Swanson

In the early 1960's the Company, then named the United States Smelting Refining and Mining Company, was drilling the Continental ore body located near Fierro, New Mexico. Reserves of underground ore of sufficient quantity were indicated to build a mill. At the same time some ore from the Continental No. 1 mine was being milled at the Company's Bullfrog Mill, formerly a lead-zinc mill. The copper ore in comparison to the lead-zinc ores was very hard, abrasive, and heavy. These factors pointed out the possibility and attractiveness of autogenous grinding. While prior to this some study had been given to autogenous grinding, no large scale tests had been made. Such a program was carried out and from the pilot plant data the following was established: 1. Grinding of the ore by autogenous means could be accomplished. 2. This could be done in one stage; however, not at a satisfactory tonnage throughput rate. Thus, the use of a secondary unit has been employed. 3. Grinding in the secondary unit could be done by pebbles generated in the primary unit. This resulted in the scheme whereby the ore would be ground 100% autogenously. 4. Liberation of the copper minerals was excellent so that good recovery at a satisfactory concentrate grade would be obtainable.

Jan 1, 1976

By B. S. Graves

Deep well disposal of selected industrial wastes has been proved feasible and acceptable in the New Orleans area by several industries including Shell Oil Company's Norco Refinery and Chemical Plant where three of the six successful disposal wells in this area are operating. Well design and procedures for restoration of capacity are based, in most cases, on the principles of brine injection developed by oil producers in South Louisiana. Geological formations in the Gulf Coast area are suited to this type of injection because receiving strata are porous, isolated from sources of potable water and their water is compatible with the liquid wastes to be injected. This method of disposal is a simple, complete and economical solution to the problems presented by certain hard to treat wastes.

Jan 1, 1964

By Thomas E. Ban

D-LM at Mobile The qualified success of iron ore pelletizing processes has influenced considerations for production of highly beneficiated fur¬nace charges. Such beneficiation would necessarily involve some forms of chemical and perhaps thermal conversion for production of prereduced pellets, preheated pellets, precalcined pellets, and perhaps pellets which contain all of the above features as preheated, prereduced, precalcined products. This type of furnace burden will be adapted within a new ironmaking process to be activated commer¬cially during the latter part of 196$ in Mobile, Alabama. This process will integrate a new pelletizing system with an electric smelting furnace and the pellets will be comprised of a composite charge blended from metallurgical proportions of iron ore, coal, and limestone. The plant as designed and constructed by McDowell¬-Wellman Engineering Company will feature the D-LM process and will be owned by McWane Cast Iron Pipe Company. It is significant to

Jan 1, 1968

By Harvey P. Knudsen

Case studies are presented in this paper to illustrate the usefulness and applicability of using conditional simulation in under- ground coal mine planning. Conditional simulation is a technique developed in the last five years that allows the building of a simulated ore body (or coal deposit) model. Construction and validation of the simulated model is described in order to show how well the model reproduces the essential characteristics of the deposit. In the model, the thickness, ash, and sulfur content are known everywhere in the deposit and each variable has the same mean, variance, and spatial variability (variogram) as that variable has in the real deposit. Use of the simulated deposit in the design of drilling strategy for long range mine planning is demonstrated in me case study. Determining the potential of short term production scheduling to reduce the fluctuations of sulfur in run of mine coal is described in the second case study.

Jan 1, 1980

By M. H. Pettibone

During the past decade, the size of grin- ding mills has steadily increased. Mills 11 m in diameter with 9 mW motors have been installed with even larger units on the drawing board. The rising costs of energy and labor have spurred interest in improving efficiency while reducing capital investment and operating labor. Autogenous and semiautogenous grinding have experienced renewed interest as efforts to reduce operating and capital costs have increased.

Jan 1, 1981

By H. Akgun, J. J. K. Daemen

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. Presented in this paper are the results of push-out tests on two types of expansive cement grout plugs emplaced in rock salt. The average interface shear strengths range from 2 to 12 MPa. Peak shear stresses (assuming an elastic stress distribution along the interface) are up to eight times higher. Dissolution along the interface may be enhanced by clay inclusions in the salt and appears to reduce bond strengths. Application of the results to the design of plugs for larger openings (e.g., shafts, drifts, or boreholes) is discussed.

Jan 1, 1995

By Errol L. Montgomery

The region of metalic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 4,600 meters. Because surface water supplies are meager, new mines require unexploited sources of water. Prolific groundwater aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate groundwater quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum production water well capacities in excess of 170 liters per second.

Jan 1, 1982

By Colin D. Jardine

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. A recent application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by the use of a "building block" approach to design and equipment selection. Details of this approach and the results obtained are described.

Jan 1, 1982

By James A. L. White

Although the quantity of native sulphur associated with volcanism is large, production from such deposits represents only a very small percentage of total world production, This paper describes the location of the known deposits, the typical geology of these deposits and the nature of the sulphur mineralization. Methods of treatment are discussed and some comments are offered on the economic position of these occurences in world sulphur markets.

Jan 1, 1967

By W. W. Mason

The United States began exporting coal in the late 1800'5, at first in very small quantities to Canada and beginning in 1897 and 1896, to the east coast of South America. Shipments to European countries began on a very limited basis in 1902 and these shipments increased gradually until World War One when shipments overseas increased from the 8 million tons per year level to 22 million tons. After the war exports dropped as fast as they had increased and, with the exception of exports to Canada, remained at very low levels until just after World War 11 when the United States again emerged as a major coal exporter. World War II left the coal industries of Europe in ruin. As the United States was the only country able to supply the large quantities of coal at reasonable prices needed for reconstruction of the European economy, the U. S. coal exports overseas expanded rapidly to 42.5 million tons in 1947. Additionally, we shipped 25 -2 million tons of coal to Canada In that year for a total export of 68.7 million tons. Unfortunately, that level was not reached again until 1957 when exports reached an all-time high of 76 .4 million tons- -a high I might add that has not been reached since.

Jan 1, 1980

By J. A. Siekmeier

The thickness of the laminated beam modeled in this study is based on bridging potential and TDR measurements. The laminated beam stiffness is based on the effective stiffness of an equivalent transformed section. The maximum deflection of this near-surface laminated beam is compared with the maximum measured surface subsidence. The spreadsheet provides a rational technique to graphically display the character of the overburden and potentially allows prediction of a subsidence factor based on boring logs and the proposed mine plan. The U.S. Department of the Interior, Bureau of Mines (Bureau), utilizes a commercially available computer spreadsheet program in combination with a modified version of Bieniawski's Rock Mass Rating (RMR) system to characterize the geology overlying high extraction coal mines. The spreadsheet program calculates a RMR for each bed based on the lithology, thickness, and engineering properties, which are determined from boring logs and laboratory tests. Once the RMR is calculated the spreadsheet has two major functions. First, the spreadsheet calculates values used to graphically represent the character of each individual bed in the overburden. It calculates an in situ deformation modulus using an empirical rela¬tionship between the modulus and the RMR and then uses this effective modulus along with additional parameters that are based on mine geometry to calculate the bending stiffness and bridging potential for each bed. Second, the spreadsheet creates a transformed section that allows groups of beds to be modeled as an elastic beam. It then calculates a bridging potential for the entire rock mass. The bridging potential of the rock mass is a single value that takes into account both the geology of the overburden and the geometry of the mine. It seems reasonable that there would be a strong correlation between the bridging potential, the overburden response to high extraction mining, and the subsidence ratio. The results presented in this paper focus on the relationship between the bridging potential of individual beds and the deformation measured using Time Domain Reflectometry (TOR). Subsurface displacements measured over seven high extraction coal mines in southern Illinois were correlated with the bed stiffness and bridging potential profiles. Based on these correlations it was evident that the process of caving and subsidence over these high extraction mines involved momentary bridging by individual beds or groups of beds and the ultimate development of a laminated beam near the surface.

Jan 1, 1986

By John L. Halls

Modern business practice dictates that in order to ensure the economic optimization of investment, the size of any investment venture must be such that every increment of capital invested in such a venture yields at least a corporate minimum acceptable rate of return. This practice is based on the premise that alternative investment opportunities capable of yielding the minimum corporate return are immediately available. If a mining corporation is to make the maximum use of its investment funds, any capital investment in a mining property must comply with the above practice. The most important parameter in estimating ore reserves is the cut-off grade which is used to separate material into ore or waste. The cut-off grade is calculated on the basis that material of cut-off grade produces sufficient revenue to cover the estimated costs of mining and processing through to sales, including depreciation and produce a pre-determined profit. Ore reserves so estimated are adequate for determining the magnitude of an orebody but do not provide a sound basis for determining plant size and therefore capital investment in a new property or for expansion consideration on an existing property. From a financial analysis of this one ore reserve it is impossible to ascertain whether each increment of capital investment is providing the minimum acceptable rate of return, Other difficulties associated with the calculation of a cut-off grade including the determination of depreciation and the amount of pre-determined profit to be included in the cut-off grade calculation are outlined in the text. The proposed solution to determine optimum ore reserves and plant size for new properties avoids the complication of calculating a cut-off grade by computing a series of ore inventories using arbitrarily selected cut-off grades. A comparison of the cash flows generated by production from such ore inventories using incremental financial analysis clearly indicates the ore reserve and plant size which will best serve the corporation's investment and metal production goals. Incremental financial analysis of a corporation's operating mines and prospects assists management in assessing the comparative expansion and investment possibilities of each property for increasing or maintaining metal production on a long term basis.

Jan 1, 1969

By L. Barnewold, A. Merchiers, M. Pütz, P. Jeschke, M. Dammers

The mining industry faces many difficult challenges, for example, lower ore grades, smaller and deeper deposits, and longer transportation distances. In the past, there have been remarkable innovations in both equipment and the types of mining methods for which it is used, which have resulted in economies of scale. This has led to an increased use of bulk mining methods, like sublevel and block caving, which has increased productivity and reduced costs. Haulage alone plays a major role. Current haulage techniques are a significant cost driver, which account for between 15 and 30% of the overall capital investment (capex) in a mine and are an increasingly part of the operating costs (opex). The paper introduces a simulation tool of main haulage system in underground mining. Therefore, performances and the costs of the three most common underground main haulage systems, rail, truck, and conveyor, are calculated using a developed modeling tool. The tool was applied and validated in a case study carried out with the LKAB Kiruna Mine in northern Sweden.

By L. W. Teal

The Paupers Dream Property is located in the northern Boulder Mountains, southwestern Montana, 30 km southwest of Helena. The property is situated in the central portion of the Butte-Helena gold belt, a NE trending lineament marking a zone of recurrent, late-Cretaceous to mid-Tertiary volcanic activity. Geology consists of a plutonic basement of late-Cretaceous quartz monzonite overlain by a pre-volcanic basal conglomerate and a complex sequence of Oligocene rhyolitic volcanics. Gold mineralization occurs in fracture-controlled quartz veins, silicified stockwork, and brecciated shear zones as auriferous pyrite, arsenopyrite, and disseminated free gold. An estimated 60,000 tonnes averaging 2.5 g/t was produced from the Porphyry Dike, Venus, and Paupers Dream Mines on the property. Current drill indicated reserves (May, 19861 are placed at 6,946,000 tonnes averaging 1.45 g/t gold.

Jan 1, 1987

By J. A. Procarione

Introduction Ventilation engineers have always felt somewhat uneasy when, in the normal course of their work, they are forced to consider the flow in any mine entry as "wholly rough." Under such conditions in pipes, friction factor is no longer a function of Reynolds' number. This assumption serves to simplify the problem and overcome an evident lack of information concerning the variability of K-factors. During the summer of 1985, a unique opportunity to investigate the reaction of friction factor to changing flow rates presented itself. A Utah coal mine was temporarily directing a substantial airflow through a single entry. By regulating the quantity, it would be possible to obtain a wide range of Reynolds' numbers in an entry composed of two distinct coal thicknesses. This paper describes the conducted study. The theory covering basic fluid flows in pipes that led to the questioning of constant K-factor is presented first. Experimental procedures are then described, including the use of a view camera in determining entry area and perimeter. Finally, a discussion of the observed variations in friction factor versus Reynolds' number is given. Changes of 34% and 45% in K-factor were seen in this study for the two entry heights. The implications of ignoring the relationship in this case and a call for an expanded research effort are also presented. Theory Since a gas is a fluid, the general principles of fluid mechanics are equally applicable to airflow in a mine entry as they are to the flow of water in a pipe. The Darcy equation is, therefore, equally applicable to pressure drop calculations in both situations. This famous formula was originally derived for use in circular cross sections and may be modified for any other shape by the use of hydraulic radius (defined as the area divided by the "wetted" perimeter). The Darcy equation relates the physical parameters of the pipe (diameter, length, and resistance to flow) and fluid velocity to the energy needed to create the flow. A study by Nikuradse (1933) brought to light the suspected dependency of the friction factor term in the Darcy equation upon Reynolds' number. By performing a large number of laboratory experiments, he established some basic concepts upon which other researchers built. Chief among these contributors was Colebrook (1939). Using commercial-grade pipe, he established an empirical relationship between Darcy's friction factor and Reynolds' number that is still in use today. If Colebrook's system of equations is plotted on log-log paper (as was done by Moody, 1944), the curves have some very distinct features. Of importance to the subject at hand is the relative response of friction factor to Reynolds' number at a given relative roughness. Simply stated, a pipe can appear to be either smooth or rough, depending on the flow conditions. As the Reynolds' number increases, the friction factor decreases at a decreasing rate until it becomes nearly a constant value. At this point, the flow is said to be "wholly rough." It is upon this condition that many traditional ventilation solution methods depend. For calculating pressure drops in a mine entry, Atkinson's equation is much more popular than the Darcy equation. Both of these formulas describe the same phenomenon and so have similar forms and functions. The K-factor in the Atkinson equation is equivalent to the Darcy friction factor and can be related by simply changing units, equating the pressure drops, and canceling like terms. A generalized form of this relationship is presented below as equation 1. K = yf/28,800g = [q]f/28,800 (1) where K is Atkinson's friction factor in kg/m3 (lb - min2/ft4), Y is the specific volume in Nt/m3 (lb per cu ft), p is the fluid density in kg/m3 (slugs per cu ft), g is the acceleration due to gravity (9.8 m/s2 or 32.2 fpsz), and f is Darcy's friction factor, which is unitless. The objective behind Eq. 1 is to show the strong correlation between K and f. Since these two quantities differ only by a constant (q]/28,000), the assumed independence of K-factor and Reynolds' number is suspect in light of the known response of f. Unfortunately, the formulation does not provide information concerning the actual relationship, as entry geometry likely plays a major role in the response curve. Only an indirect indication that such a relationship might exist is provided. Previous work on this subject was performed by Thomas Falkie (1958). The study involved a laboratory model composed of sections of straight, steel duct and a range of Reynolds' numbers from 15,610 to 137,200. Results from this work show a variation in friction factor with Reynolds' number in much the same way as it was found to vary in pipes. Over the range of velocities examined, a decrease of approximately 38% in K-factor was observed. This previous experience provides additional incentives to investigate the phenomenon under field conditions. Past model studies done at the University of Utah by Ozukurt (1945), Biron (1944), and Greenhalgh (1942) present similar evidence of this variability. More recently, Kharkar's (1974) study of coal mine friction factors contains similar indications that K-factor is not constant in all situations. Taken together, the data

Jan 1, 1988

By Gerald L. Colborne

The major role of financial institutions in the free world in the development of mineral resources is to provide the necessary capital in the form of loans to underwrite the development of these resources by the industry on a stable and continuous basis. This capital provided by the depositors to the bank must be invested in sound projects where the degree of risk is relatively small, the return on the investment is reasonable and the time to retire the loan is of short duration. Money is, therefore, one of the important ingredients along with technology, manpower and an exploitable resource that will provide a sound economic base in this region of development. Canadian banks are similar to banks of other western nations, although each country has some differences in their banking systems. The basic difference between the American and Canadian systems is that the former employs unit banking while the Canadian utilizes the more mobile branch system, which is prohibited or restricted in the United States and some other countries. Canadian banks are the subject of this paper, so, subsequent material will relate to Canadian banks unless indicated otherwise. It will be realized by everyone that the mineral industry is only one area of the economy in which the banks are interested and to cover the subject matter in the time allowed, the topic is restricted to mineral resource development. In Canada this is a vital sector of our economy and before we outline some of the details of financing and services involved in various aspects of mineral development, a review of the Canadian mineral industry is a necessary part of the sequence of presentation. The writer presents this material as a resource engineer advising a major bank in mineral matters, so the presentation may relate more to the financial problems of the developer

Jan 1, 1972

By C. P. Mangelsdorf, Richard A. Allwes

At the request of the U.S. Department of Labor, Mine Safety and Health Administration (MSHA), the U.S. Bureau of Mines evaluated the suitability of using tri-sets for protecting mine personnel in roof-fall prone areas. A steel-set arch provided by MSHA served as a basis for evaluating the performance of the tri- set. All tests and analyses were conducted according to the arch canopy test and design procedures developed by the Bureau. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of their experimental behavior. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri -sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that tri-sets may be considered for protection against roof falls, provided that the arch canopy design procedure is utilized for each application and that the principles underlying the design procedure are understood.

Jan 1, 1992

By MAURICE SUNKPAL, Taghi Sherizadeh, ELAHEH TALEBI, PEDRAM ROGHANCHI

Excessive heat exposure is among the health and safety hazards for mine workers. The nature of the underground climate makes it a convenient avenue for heat generation and accumulation from several heat sources, including autocompression, equipment and heat from strata. This study investigates the effects of clothing insulation and acclimation on the thermal comfort of mine workers exposed to heat in underground working environments. Several clothing ensembles were considered to analyze the effect of the thermal resistance of clothing on the workers’ thermal comfort. To investigate the impact of clothing insulation, the thermal comfort limit of an underground miner was calculated in the form of maximum allowable exposure time for an eight-hour shift.

By Joseph P. Sobanski, Michael P. Bruen

The North Branch tunnel segment of the Tunnel and Reservoir Plan Mainstream System consists of 14,075 m (45,885 ft) of 9.2 m (30.2 ft) finished diameter and985 m (3,232 ft) of 2.5 m (8.25 ft) finished diameter concrete lined rock tunnels. The TBM mining and concrete lining methods used in completing this $166million project differed from “typical” TARP construction methods in that a two-stage concrete lining was placed and the lining was initially placed concurrently with TBM mining as a two pass system in the same tunnel segment. For the main tunnel (9.85 m diameter), TBM mining averaged 24 m/day (79 ft/day), excluding downtime associated with two main bearing changes, and the concrete lining placement, averaged 117 m/day (380 ft/day) and 53 m/day (174 ft/day) for the invert and arch segments, respectively.

Jan 1, 1999