Search Documents

By Andrew Cushing, Joe Carvalho, Jon Hurt

"INTRODUCTIONThe shales of the Greater Toronto Area (GTA) have been known to experience time-dependent deformations (TDD); those initiated by excavation-induced stress relief which progress with time as a function of rock porewater salinity, access to freshwater (or air) of lower salinity, clay and calcite content, and the buildup of swelling pressures within the rock mass. These deformations can induce long-term pressures on shaft walls and tunnel linings, especially if the permanent works are constructed soon after excavation, with very little time delay. This paper presents measurements of time dependent deformation of recent shaft and tunnel projects constructed in the GTA, and draws conclusions regarding the main influences on the TDD. The key input parameters for the numerical predictive model are critically assessed. Projects which are discussed include the Billy Bishop Airport Pedestrian Tunnel, Hydro One Midtown Tunnel and Hanlan Feedermain (Contract 3).MECHANISM OF TIME DEPENDENT DEFORMATIONExplanation of MechanismThe Georgian Bay Shale unit consists of typically moderately weathered to fresh, grey to dark grey, fine to very fine grained fissile shale interbedded with slightly weathered to fresh grey, fine grained calcareous siltstone and limestone interbeds. There are two distinctive features of the shale in the Greater Toronto Area (GTA). One is a high horizontal stress regime, and the second is long-term time dependent swelling behavior which develops when the following factors occur (Lo and Micic, 2010):• Stress relief of the rock mass• Outward salt concentration gradient from pore fluid of the rock to the ambient fluid• Availability of fresh waterThe swelling is a consequence of the reduction in confined stress in the rock which occurs upon excavation in combination with a differential gradient in salinity between the saline rock porewater and freshwater or even humid air. Osmotic and diffusive processes result in a decrease in the salinity of the rock porewater achieved by an overall increase in the water content, resulting in volumetric expansion of the shale rock over time. The development of this time dependent deformation (TDD) relative to the time"

Jan 1, 2016

By Ian J. Duckworth, Pierre F. X. Mousset-Jones

A detailed heat flow project was conducted at the Homestake Mine in Lead, South Dakota. This paper presents results obtained from a stope sensor system installed in the mine. The design and installation of the system are described in detail in a previous paper (Duckworth et al., 1992). The major project objective was the construction of a comprehensive heat flow data base to allow the design and testing of a new climate prediction model applicable to irregularly shaped underground excavations in non-homogeneous surrounding rock types. A mechanized cut-and-fill (MCF) stope contributes a substantial overall heat source in a mine, and the effect of this source on the working environment must be considered when planning future ventilation and refrigeration requirements. The relative magnitudes of the component heat sources encountered with the MCF mining technique are presented, having been computed from actual stope beat flow data collected over a one-month study period. The percentage of the overall heat load that is removed from the scope for each component heat sink is evaluated, and the overall energy balance is analyzed. A one-month study length was considered a sufficient period of time to allow stope monitoring for a complete range of mining conditions.

Jan 1, 1993

By Allan E. Hall, Stephen G. Hardcastle, Lucien D. Nel, Jean-Paul Saindon

A description is given of the investigation conducted at Sherritt Gordon's Ruttan Operation in Manitoba during 1986. Gas and dust concentrations were measured in the exhaust air of the major working sections to assess the potential for recirculating exhaust air into the intake air in winter to reduce heating costs. The results indicate that there is excellent potential to significantly reduce winter heating costs by controlled recirculation of exhaust air. Gas and dust concentrations vary significantly during the working shifts but have consistent trends from shift to shift and day to day. The variations in gas concentrations have similar trends but no single gas could be reliably used to predict the variation of the other gas or the dust concentrations. Dilution and the other effects which reduce pollutant levels as the exhaust air returns to surface indicate that recirculation should take place as close to surface as possible, subject to the economic constraints of the airway construction required and the extra fan energy required for the longer recirculation path. Recommendations are made for the choice and positioning of air and dust monitoring sensors and the logic of a control system. Economic analysis of the results indicates that controlled recirculation is viable at an existing mine with a pay back period of approximately two years. Incorporation of a system into a new mine at the planning stage would significantly shorten the pay back period.

Jan 1, 1987

By F. Ansheng

Though it becomes increasingly important with the valuable minerals in their deposits tending to be fine and poor, the solid and liquid separation remains difficult especially when the particles are of micrometer size and of low density. Almost of all conventional thickeners result in that fine particles lose into overflows which often costitutes a loss of potentially valuable resources as well as an environmental hazard. The addition of flocculations may improve the settling of solids but may also not work well for the final removal of fine particles from the overflows (Ref.1).

Jan 1, 1990

By A. Griffiths

The? use of hydrogen peroxide to detoxify gold mill waste waters containing cyanide and other toxic substances is already an established technology. Recent advances have extended the range of application of hydrogen peroxide treatment to include the removal of complex iron cyanides, the simultaneous removal of cyanide and toxic metals down to very low levels and treatment of barren bleeds, CIP' pulps and tailings pond discharges. Three treatment plants are described here. Each was installed at a gold mine in North America in 1987 and each illustrates a different application of hydrogen peroxide. The need for individual design of the detoxification plant to fit particular requirements is shown by the examples chosen.

Jan 1, 1988

By Jr. Raleigh

Three run-of-mine bituminous coals, which ranged in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µ m), -100 mesh (150 µ m), and -400 mesh (37 µ m) feed particle sizes with selected pyrite depressants and a dispersant. For the coals tested, pyrite and ash-forming minerals were usually rejected best at a -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µ m) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1990

By Ulrich Maidl, Marc Comulada, Janosch Stascheit

"INTRODUCTION Cohesive soils are notorious for causing clogging of the cutter head and the excavation chamber of tunnel boring machines (TBMs). While clogging leads to a drastic reduction in excavation performance, it further induces higher wear of tools and other parts of the cutter head and may even prevent a controlled support of the tunnel face and, thus, lead to face collapse and excess settlements or sinkholes. Employing well-balanced soil conditioning techniques, the clogging tendency can be significantly reduced. The monitoring and control of soil conditioning as well as the timely detection of potential clogging tendencies require a close monitoring of all relevant machine parameters and measurements. To this end, a reliable and powerful Process Controlling software that gathers all machine and process-related information is a prerequisite for successful mitigation of clogging-induced problems. The remainder of this contribution is organized as follows: First, a brief introduction to the Process Controlling system PROCON is given. Afterwards, the mechanisms and mitigation techniques of clogging are discussed. Finally, an example is given how Process Controlling has been employed to soil conditioning in a tunneling project with highly clogging soils.PROCESS CONTROLLING Being both the active part and a huge measuring device, the shield machine represents the core component in mechanized tunneling. This machine comprises a manifold of complex components and devices that require constant supervision and control and, thus, is equipped with a manifold of different sensors that provide a continuous monitoring of the state and condition of the machine (Maidl & Stascheit, 2014). If these data are put into the whole context of the tunneling process, they can provide insight to the assessment and optimization of the performance and to the prediction of potential risks and hazards such as, for example, the tendency of clogging of the cutter head."

Jan 1, 2016

By A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, Y. Xiong, J. Gu

"As ores degrade, mining techniques and chemistries change to meet market demand and maintain product quality. The balance of recovery and grade is a significant challenge in the Crago Process where an anionic collector is used to float phosphate, followed by acid scrubbing, then an amine float to improve product grade. As the grade is a requirement for DAP and MAP production, recovery is the criteria to suffer. Phosphate losses in the amine float can bring overall recovery down by as much as 18%, creating a growing need to think outside the box to improve recovery. This paper will focus on the theory of amine tail recycling and the best methods to optimize the overall phosphate recovery by recycling the tails from the cleaner flotation step. INTRODUCTION In 2014 the total US phosphate production was down 13% over the prior year, from 31.9 to 27.1 Mt, which accounts for 12.32% of the world’s phosphate rock production. Florida and North Carolina phosphate production accounted for 80% of total US phosphate production, which was down from 85% the previous year. This decline is due in part to the closing of the last phosphate mine in Polk County, FL - which had an operating phosphate mine for over 100 years (Gurr, 2015). Another factor contributing to the reduction in contribution from FL & NC is the increasing challenges in beneficiating the remaining ore deposits. The Central Florida mining district has historically been in the Bone Valley deposit, where raw apatite was abundant with P2O5 values as high as 15%. The Bone Valley ore also had characteristics favorable to beneficiation to 27.5-29.7 %P2O5 while achieving recoveries above 86%. The move southward into the Hawthorne Formation has seen the ore feed grade hit some historic lows, and the matrix characteristics pose more challenges to phosphate producers. The Hawthorne Formation experienced lateritic weathering after the Bone Valley formation which altered the apatite to aluminum phosphate minerals, and alteration of montmorillonite to kaolinite, releasing MgO that caused the dolomitization of the top of the Hawthorne limestone (Cathcart, 1966). Elevated levels of dolomite can yield an increase in slurry viscosities, reduce production rates, and increase energy costs in the wet-acid fertilizer process. The MgO will also act to dilute grade, making it more difficult to achieve a standard 18-46-0 product (McHardy, 1981)."

Jan 1, 2016

By Charles H. Greene

This paper will describe briefly the steps taken in the development of a Central Florida phosphate ore deposit from acquisition to mining. Further, the design and early operation of the mining and beneficiation facilities will be depicted. During the 1950's, with confidence in the continually increasing requirement for phosphate fertilizer materials essential for producing food, I'. R. Grace & Cc acquired the Hookers Prairie tract containing approximately 45 million metric tons o. (50 million short ton~ of potential phosphate rock product. In 1973, at a point when the Grace captive need for rock was being greatly enlarged by a planned doubling of its Bartow phosphate chemicals plant capacity, the decision was made to expand existing phosphate rock production by building a new mine and plant. The initial annual capacity was to be 2.3 million tons (2.5 million st); however, subsequent investigation pointed to a higher than estimated dragline operating factor 'and the forecast of annual capacity was set at 2.5 million tons (2.8 million st).

Jan 1, 1977

By M. A. A. de Klaver

Due to the current cost and availability of crude oil in Brazil, Samarco Mineracao S. A., as part of its program of quality and productivity optimization and reduction of operating costs, has undertaken tests to utilize alternate energy sources for fuel oil used in its pelletizing plant at Point Ubu, Espirito Santo, Brazil. The energy program undertaken by Samarco consists of two basic steps. The first step was to reduce energy consumption, that is, to improve the thermal efficiency of the process. Secondly, a program was started to substitute the fuel oil with coal.

Jan 1, 1984

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

By G. Castillo, J. Mortensen

"INTRODUCTION Molybdenite is typically produced as a co-product in the copper ore flotation process. At the Rio Tinto Kennecott Concentrator (RTKC) in Copperton, Utah, the molybdenite is initially floated with copper sulfides and other value minerals producing a Cu-Mo concentrate. This is then separated in the molybdenum plant by depressing copper sulfides and pyrite and floating only molybdenite. The molybdenum plant in RTKC comprises the rougher circuit and several stages of cleaning to achieve a certain grade requirement of Mo. The rougher circuit is where the first stage of separation occurs. Cu sulfides and pyrite are depressed in the rougher circuit by adding NaSH under nitrogen and in the cleaner circuit by adding NaSH under air. The depression of Cu sulfides (and pyrite) by NaSH is related to the redox activity1. It is important therefore to maintain a reducing potential in the circuit in order to achieve effective Cu-Mo separation. If the rougher circuit is under air, like RTKC’s molybdenum cleaner circuits, it is harder to maintain the target redox potential because NaSH oxidizes rapidly in the presence of air thereby increasing NaSH consumption significantly. CU-MO SEPARATION AND ROLE OF PULP POTENTIAL The collector adsorption on copper sulfide minerals is through an electrochemical mechanism2. The collector changes the surface chemistry of the Cu mineral allowing it to float. Molybdenite, or MoS2, on the other hand, floats readily in the presence of a frother as it is naturally hydrophobic. Usually, hydrocarbon oil extenders such as diesel or burner oil are added to enhance Mo recovery. In order to effectively separate Cu from Mo, the collector complex on the copper surface needs to be destabilized or desorbed using a reducing agent such as NaSH or Nokes. As long as the circuit is under highly reducing conditions, the collector remains detached from the sulfide mineral surface allowing Cu sulfide depression. Therefore, it is important to measure the oxidation-reduction potential (ORP) continually and maintain the reducing condition with addition of NaSH. For a given collector each mineral will have a characteristic potential or electrochemical window for flotation to occur3, therefore, it is necessary to reduce the potential outside of this window in order to effectively separate Cu and Fe sulfides from MoS2 minerals2. In RTKC plant, the target reducing condition is between -450 to -550 mV to effectively destabilize the collector and depress Cu and Fe minerals. Typically the dosage of NaSH used in the molybdenum plant could range from 6 to 30 gallons/min (gpm). The high dosage of NaSH could pose risk of H2S exposure. RTKC wanted to evaluate alternatives to NaSH in order to reduce its consumption and minimize risk of H2S gas generation."

Jan 1, 2016

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Gas holdup profiles in the collection zones of a pilot flotation column (0.91 m x 13.5 m) and a laboratory flotation column (0.057 m x 9.5 m) operated with air and water only were determined from pressure measurements. The profiles were determined discretely and continuously. For the pilot column, a minimum distance between pressure measurements was necessary to give reliable results. For the laboratory column, a third-degree polynomial fit to the pressure vs. height data was required. Water manometers proved to be less sensitive to sensor and process noise than pressure transducers. The profiles showed that gas holdup approximately doubled over a height of 8 to 10 m. The profiles were not linear, and the gradient increased towards the top of the column, especially for gas rates greater than 1 cm/s. The profiles cannot be predicted by a simple bubble expansion model. The implications of this new finding of a significant gas holdup increase with height in the collection zone on various aspects of flotation column design and operation are discussed.

Jan 1, 1996

The impact of a methane explosion on mining operations cannot be over-emphasized. The explosion is a result of rapid combustion when a methane/air mixture is ignited by an unexpected energy release, such as a mine fire, electrical arc or sparks caused by frictions or rock falls. In most cases, an ignition of methane/air mixture could result in a deflagration other than detonation. Resulting flames and overpressure induced by a methane deflagration will harm neighboring miners and local ventilation control devices.. ,It is essential that the mechanism of an explosion and associated destructiveness be fully understood. This research seeks to predict an influence region of an incident happened within a representative underground mine geometry. The most common geometric changes in an underground coal mine are bends, regulators/doors, obstacle in airways and changes in sectional area. These geometric changes could result in an attenuation of the flame and pressure wave as a result of a methane deflagration. A study of this phenomenon could enable mine planners to have better understanding of the over-pressure redistribution due to the explosion. Both numerical and experimental work has been done in this study to ascertain a better insight of this potentially devastating event. The experimental data are also used to validate the turbulence and combustion models used in this test.

Feb 23, 2014

By Henning E. Soderberg

Yesterday, air pollution was somebody else's problem -- today, it is everybody's problem. The coal industry with thermal coal drying, is aware of their problem and the necessity of doing an acceptable job; however, there is much to be said as to how good a job is required and what performance limits should be set up. American Air Filter Company has been one of the pioneers in the solution of the thermal coal dryer dust problems, Because of high moisture content, products of combustion and occasional temperature surges, only wet collection has been considered as the practical approach. Our first installation goes back some 12 years with a total to date of 29 Individual wet collectors, each, fabricated of suitable corrosion-resistant material, at 14 operating plants. To eliminate a potential air pollution problem, a performance requirement of not more than approximately one-quarter (1/4) grains per cubic foot in the dust collector discharge was used. In nearly all installations, operating performance surpassed requirements, but discharge stacks were not entirely free of discoloration. However, plant nuisance and air pollution complaints were eliminated. This satisfactory performance was accomplished by medium priced wet dust collectors operating at a 4-6" W.G. pressure drop with cater drain requirements of about 1 gallon of drain water per 1000 cubic feet of air exhausted.

Jan 1, 1962

By A. Nieto

Rare earth elements (REEs) are crucial to green technology such as hybrid-electric vehicles, wind turbines and fluorescent light bulbs. As of 2011, China dominates the global production of REEs and is reducing its export quotas. To predict the supply of rare earths in the United States based on future supply scenarios, a web-based database and geographic visualization tool was built. Five case scenarios with varying levels of REE demand were created by varying several economic conditions including (1) international trade policy, (2) greenhouse gas regulations, (3) environmental mining regulations and (4) tech applicability ratio of REEs. The most likely scenario, which is based on current international demand levels, indicates the importance of expediting the development of extractive operations of current REE resources within the United States. The results of the different case scenarios are supported by using dynamic geographic maps indicating the location of rare earth ore (REO) resources.

Jan 1, 2012

By M. Misra

A sample of thorium-contaminated soil from Kirtland Air Force Base (AFB) was subjected to froth flotation for removing thorium contaminants. A series of flotation tests were conducted to screen and evaluate the reagents. Among the collectors used, sodium oleate exhibited to show the promising results. Preliminary tests showed that a concentrate having activity as high as 5300 pCi/g can be obtained from the contaminated feed soil having activity 800 pCi/g. The volume reduction obtained was 89% and the activity recovery in the concentrate was 68%. The paper discusses the physico-chemical characterization data and the potential physical separation decontamination schemes for the thorium contaminated soils.

Jan 1, 1996

By George M. Anderson

The extraction of industrial minerals is usually confined to relatively small mining operations. The recent COSMAR (Committee on Surface Mining and Reclamation) report found that 93% of all mines in the United States were of the small unit variety. Also, of the total number of mines in the U.S. (15,279) 96% were in the industrial minerals (non-metals excluding coal) category. To break it down further, 86% were sand and gravel, and crushed stone operations. Therefore, we are talking about a very large number of small mining operations. If these small miners can afford to hire a college graduate, what kind of training should this person have beyond the normal mining engineering curriculum to best serve the problems that he or she will encounter?

Jan 1, 1981

Ventilation 'is currently used in mines to sustain human life, prevent explosions, and provide a more healthful work place. Future automated-mining systems could use ventilation techniques quite. different from today's practices. The Bureau of Mines is anticipating various methodologies for ventilating the automated mining systems which are now beginning to emerge in the mining industry. This paper examines the special ventilation requirements for automated mining systems. Topics include requirements for automated systems, current studies with blowup ventilation tubing, and ventilation of two types of highwall -ripper type mining machines.

Jan 1, 1990

By J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts, and make the repair; of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner, and tested. This paper summarizes the development of the diagnostic system, and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Finally, comments on the system's performance are presented.

Jan 1, 1993