Search Documents

By William O. Rasmussen

Exploration requires processing highly varying kinds and amounts of geologic information. Successful discovery dictates that this be done quickly with maximum confidence. Most phases of exploration are more or less applicable to computer reduction on a routine basis. The use of digital computers to reduce raw data into interpretable form, lets the exploration geophysicist concentrate on interpretation and presentation, and to consistently apply more sophisticated and comprehensive analytical techniques, not practical before. In applying these concepts for the past several years, various efficient programs have evolved which provide more complete evaluation of all data including the pro- vision for more unique solutions. This has resulted in greater refinement and ability to select the most advantageous drill sites in a minimum time at a minimum cost or, in rejecting as soon as possible a project on which additional effort is no longer justified. Practical examples of computer applications in magnetics (air and ground), induced polarization and resistivity are discussed.

Jan 1, 1969

By D. L. Shenck

The Navajo Mine is exclusively a multiple seam surface coal mine located in the northwest corner of New Mexico, and entirely on the Navajo Indian Reservation (Figure 1). It is owned and operated by the Broken Hill Propriety Co., Ltd. of Melbourne, Australia. The mine began production in January 1963 with a long term fuel supply agreement with the Four Corners Power Plant. The 2175 MW nominal generating capacity of the Four Corners Power Plant consumes 8-8.5 mm tons of coal annually. With estimated reserves totaling 1.1 billion tons of strippable coal, only one third is presently committed to the generating station. As development has continued over the years, mining operations have advanced into more complex geologic areas to satisfy the utilities demand for coal.

Jan 1, 1990

By Arshad Ali, Mudassar Khan, Waqas Ahmad, Nisar Muhammad, Muhammad Salman

Talc is an important industrial commodity due to its wide-ranging intrinsic properties; however, the presence of iron oxide hinders its industrial utilization. Herein, we report the purification of Pakistani talc through acid leaching assisted by chlorination techniques. Among various acids (i.e., HF, HCl, H2SO4, HNO3, H3PO4, Aqua Regia, H3BO3, and CH3COOH), HF was the most effectual, removing up to 67% of iron oxide at optimized conditions of temperature, 90–95 °C; time, 120 min; HF concentration of 5%; and at a pH of 1. In the second step, chlorination of the talc sample was performed separately by both wet chlorination and dry chlorination. Wet chlorination was carried out using KMnO4 and HCl in slurry phase which shown about 52% removal of iron oxide, whereas dry chlorination with CaCl2 at high temperature attained about 48% removal of iron oxide from talc sample. Further, the wet chlorination of HF leached samples was also performed under optimized conditions which showed up to 87% iron oxide removal. The original and treated talc samples were characterized by EDX and XRD analysis to monitor the changes in the elemental and mineralogical composition of the talc. It can be concluded that HF leaching followed by wet chlorination is an effective method for the upgradation of low-grade Pakistani talc ores.

Aug 9, 2021

By R. E. Nelson

The Alton Coal project, located in south-central Utah, lies at one point just over six miles from Bryce Canyon National Park. This region of the southwestern United States has been called the "Golden Circle" of national parks and monuments. Can a mine be inserted into this region so that it does not intrude on this spectacular landscape? The Alton Coal Project is a proposed surface coal mine designed to serve as the fuel source for the Harry Allen Power Plant, a 1,000 megawatt generating station planned for a site 25 miles northeast of Las Vegas, Nevada. The mine and the power plant will be connected by an underground pipeline through which coal will be transported in slurry form.

Jan 1, 1988

By P. F. Ziemkiewicz, A. S. Knox

Large-scale use of CCBs in mine environments involves filling surface and underground coal mines with ash to address hydraulic problems, AMD, backfilling and subsidence. The environmental risk of land filling CCBs is generally evaluated by the Toxic Characteristics Leaching Procedure (TCLP) or the Synthetic Precipitation Leaching Procedure (SPLP). However, there is doubt regarding the applicability of these tests to long-term CCBs leaching behavior in groundwater associated with coal mines. The Mine Water Leaching Procedure (MWLP) was developed to provide a site specific risk assessment tool. The MWL Pprocedure is presented in this paper and compared with TCLP as a study.

Jan 1, 2003

By Paul W. Johnson

Chemical mining is the in situ extraction of metals from ores located within the confines of a mine (broken or fractured ore, stope fill, caved material, ores in permeable zones) or in dumps, prepared ore heaps, slag heaps, and tailing ponds on the surface. These materials represent an enormous, untapped, potential source of all types of metals. The field of chemical mining, now in its infancy, encompasses the preparation of ore for subsequent in-place leaching, the flow of solutions and ionic species through rock masses and within rock pores, the leaching of minerals with inexpensive and regenerable lixiviants under prevailing conditions of the in-place environment, the generation and regeneration of such solutions, and the recovery of metals or metal compounds from the metal-bearing liquors. It is not inconceivable that eventually our ore reserves will consist largely of low-grade, refractory, and inaccessible new deposits and low-grade zones near previously worked deposits, caved and gob-filled stopes, waste dumps, tailing ponds, and slag-heaps. Chemical mining promises economic recovery from these types of deposits. Before it can come of age, however, a much better understanding is needed concerning its chemical and physical aspects.

Jan 1, 1967

By Edward Holloway

The basis for the selection of the ultimate pit for an open-pit mining operation is generally opaque. Some form of value-based analysis will generally guide the final decision; however, the value will often gradually plateau while the ultimate pit size continues to increase. There is no established framework to guide specialists in the selection of the ultimate pit, with such decisions regularly made on a somewhat arbitrary basis. The key component that is missing from the analyses typically used to select the size of the ultimate pit is risk. Once risk is quantified within the analysis framework, the decision-mak-ing range is significantly reduced and the process for select-ing the ultimate pit becomes more consistent, replicable and defensible. The technique outlined in this paper provides an approach to including risk in the process used to select the ultimate pit.

Jun 1, 2024

By P. M. Pettit

Hydrologic investigations at Gold Quarry began in 1989 and continued through 1991. Hydro-stratigraphic units include Tertiary sedimentary rocks, Paleozoic siltstones and carbonates. These units display complex and variable aquifer parameters as a function of faulting and hydrothermal alteration, creating compartmentalized hydrologic domains. Testing has included step-tests, spinner production logs and constant discharge tests. Two Three-Dimensional Finite Element Models have been developed, one for optimizing the pit dewatering system and the second for predicting regional impacts of dewatering. Aquifer testing and long term pumping have been used to calibrate both Finite Element Models.

Jan 1, 1992

Laboratory tests were conducted to evaluate the silica collection efficiency of flooded-bed scrubbers with six different filter panel designs and at two operating velocities. Test results indicated that reductions in filter density negatively impacted respirable dust collection. Silica collection efficiency for the least dense filter was as much as 33 % lower than the collection efficiency of the densest filter. At the low operating velocity, the least dense filter allowed over 40% of the respirable silica dust in the scrubber intake air to pass through the unit, where it would be discharged back into the mine environment. Operation of the scrubber at the higher test air velocity increased silica collection efficiency, regardless of the filter panel tested. The density of the filter panels also impacted the quantity of air that is moved through the scrubber, with higher density filters reducing scrubber airflow. For each filter, the relationship between dust collection efficiency and air moving capacity must be considered to determine overall effectiveness for specific mine applications.

Jan 1, 1998

By d&apos, L. F. G. Assumpcao

Kaolin samples from Rio Capim resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the color removal process. Coating clays and delaminated clay were tested. Retention time (or pulp injection velocity), magnetic field intensity and matrix type were the' variables studied. The feed brightness ranged from 84.7 to 87.6 % ISO for the coating clays and from 80.7 to 85.4 % ISO for the delaminated clay. The results showed unleached brightness values higher than 88 % ISO for coating products and higher than 87 % ISO for the delaminated product, using a conventional magnetic separator with an applied field of 1.5 to 2.0 Tesla. With a maximum field intensity in the superconducting machine of 5.0 Tesla, unleached brightness values higher than 88.5 % ISO for both coating and delaminated clays were attained.

Jan 1, 1995

By P. J. Bethell

In the froth flotation process the detrimental effect of slimes on the froth flotability of valuable minerals has long been known.1 Work by Aplan2 on the froth flotation of coal has shown that the presence of clay slimes causes loss in flotation selectivity, and recovery of combustibles. Obviously then the presence of clay slimes to any great extent in the froth cell feed in a coal preparation plant is undesirable. This problem is exacerbated in plants treating raw 600 um (28#) by zero material due to the variation in flotation with size. The net effect of this phenomenon in a bank of cells treating raw minus 600 µm (28#) material s that by the time adequate flotation of the coarsest size fractions has occurred the finer sizes are already producing undesirable high ash material, which often leads to unacceptable overall quality. Reduction in aeration rate and/or chemical addition to combat this, further decreases the flotation rate of the coarsest fraction leading to heavy losses of coarse low ash coal to the tailings. The above mentioned characteristics formed a key aspect of the fine coal circuitry design at Elk Run Coal Company in Sylvester, WV. The plant was designed to produce compliance steam coal (less than 1.20 lbs. S02/million b.t.u.) Desliming ahead of the froth flotation was included, as the slimes in the plant feed were clay rich, had very high ash levels, and low potential recovery. Lab testwork had also shown that poor selectivity would be expected if raw minus 600 um (28#) material was froth floated.

Jan 1, 1986

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By Roger C. Wilmoth

The most common method of treating mine drainage to prevent water pollution consists of neutralization and aeration. This process removes the acidity, iron, aluminum, and some other heavy metals, but does not render a water suitable for domestic or industrial use because of the high dissolved solids, hardness, and sulfate in the treated water. The Environmental Protection Agency (EPA), has been sponsoring and conducting research since 1966 on the use of reverse osmosis (R.O.) for the treatment of mine drainage. This process has been found to be highly effective in the removal of nearly all the dissolved solids. In addition, since R.O. is a concentrating process, potentials for recovery of valuable heavy metals are possible. This paper is a review of the state-of-the-art on the treatment of mine drainage by reverse osmosis.

Jan 1, 1972

By Dan Eyde

Low levels of thallium were detected in the mine water drainages, and process water discharges of western mining and smelting operations. This required remediation under state regulatory standards, which allow discharges of no more than .0017 ppm thallium in mine water discharges. Influent streams containing thallium can be mitigated to state discharge standards after a single pass through the series of fluidized upflow columns. Test work to determine the optimal flow rates used pilot scale systems at two separate locations treating 5 - 25 gpm of effluent. The test system at the gold mine mimics the full-scale system, which will be based on the existing upflow carbon tanks that have been converted to zeolite columns. The system installed at ASARCO's East Helena smelter has a far more complex influent stream with a high loading of competing cations. Nevertheless the columns filled with CABSORB® are successfully mitigating the thallium contamination. CABSORB® ZS500RW is a product based on the sodium analog of the zeolite mineral chabazite named herschelite.

Jan 1, 1998

By J. Y. Kim

Lead ions originating from galena during processing of complex sulphide ores migrate to "cover" the surface of sphalerite and iron sulphide mineral particles, and cause poor selectivity in differential flotation. Generally in sulphide ore processing, the lead-activated minerals float in the Cu/Pb rougher circuit. Subsequently, surface lead complicates the zinc flotation circuit by lowering the concentrate grade due to the co-flotation of lead-activated iron sulphide minerals. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zn and Pb-Zn ores is discussed. Plant and laboratory test data are interpreted by determining the surface composition of individual grains of sphalerite and iron sulphide particles using two surface analytical techniques, Laser Ionization Mass Spectrometer (LIMS) and Time of Flight-Secondary Ion Mass Spectrometer (TOF-SIMS). Cationic and anionic species on the surface were analyzed to elucidate the phenomena.

Jan 1, 1995

By R. L. Grayson

Compliance standards for respirable dust which are reduced because of high quartz concentrations have become an industry-wide problem. Research on the physical and chemical character of quartz-classified particles in respirable coal mine dusts indicates that they may exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quartz particles of a mine dust are "pure," then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. If, however, the quartz is locked inside another material matrix, or coated, a reduced compliance standard may not be appropriate.

Jan 1, 1990

By J. M. D. Wilson

The literature relating to binders in iron ore pelletizing is reviewed from the point of view of their established or proposed bonding mechanisms in green and dry pellets.

Jan 1, 1981

By C. E. Capes

The spherical agglomeration process provides an attractive method for the cleaning and recovery of fine coals in the form of compact oil-bonded pellets. In treating a washery effluent containing 50% minus 20 micron material by this technique, the slurry was first mixed under vigorous agitation with oil to deash and dewater the fine coal. The flocculated coal pulp was then formed into larger agglomerates on a modified balling disc. The operation of a semi-pilot scale process is described and an analysis of some of the operating and system variables is given. A semi-theoretical expression to predict the final agglomerate size under various conditions is derived and compared with the experimental data. Coal producers are faced with a growing requirement to clean and recover fine mesh coals. Greater mechanization of the extractive and preparation processes has resulted in finer-sized products containing larger quantities of associated foreign matter and preparation plant effluents contain quantities of fine coals which are potentially valuable. These losses will probably increase with the expansion of production and will require the development of effective disposal and utilization processes under pressure of the lack of adequate disposal areas, the enforcement of air and stream pollution laws, and the economic need to obtain the maximum yield of salable product(1)

Jan 1, 1970

By D. M. Hausen

Carbonaceous gold ores are ubiquitous to virtually all of the Carlin-type gold deposits along the Carlin gold belt in north central Nevada, representing the unoxidized "zones" of presumably extinct thermal spring systems of mostly Tertiary age. A period of subtropical weathering resulted in deep sub-lateritic zones in most deposits to several hundred feet below surface. Carbonaceous ores below this supergene profile of weathering have been investigated by various methods, including petrographic study, standard geochemical and organic carbon analyses, carbon and hydrogen isotopic ratios, electron-spin resonance spectra, infrared spectra, and DTA techniques. Results have been integrated with recent findings by other investigators utilizing fluid inclusion and thermal brine data to indicate a first phase hydrothermal solution temperatures and pressures at a minimum depth of 6 km under normal geothermal gradient. This phase resulted in the quartz-barite-calcite vein filling of the host rocks. Gold mineralization took place later at shallower depths. Primary organic material in carbonaceous ores from the Carlin and other mines appears to be a pyrobitumen residue derived from an old oil pool that had been heated by the thermal solutions, and from which the light hydrocarbon fractions were removed. Some of the bitumen was remobilized along silicified veinlets in the ore, but its role in the emplacement of the gold, itself, is not clear. The gold was localized submicroscopically in fine pyrite, mostly in framboids, and as fine metallic particles, but does not appear to be concentrated within the carbonaceous matter per se. However, reducing conditions associated with bituminous residues are believed to have been favorable for gold deposition.

Jan 1, 2013

By K. N. Han

Coal is becoming increasingly important as a major energy source in the face of the world's depleting energy mainly based on oil reserves. Coal is by far the most abundant fossil fuel both in the United States and abroad. Currently, because of increased mine mechanization, the fineness of preparation plant feed is increasing. Further, in the future as the grade of coal diminishes and the sulfur content increases, upgrading preparation of coal is very important. Because the density of coal is less than that of rock materials that occur as impurities, coal is separated from such waste largely by gravity-controlled processes for particle size between 5 inches and 28 mesh. If the size of coal particles is below 28 mesh, froth flotation is a good method for upgrading fine coal. Previously, numerous investigators have tried to upgrade coal values by froth flotation(1-16) and have achieved moderate success. However, the recovery and grade of coals in the concentrates are not always satisfactory, especially when the particle size is small. In general, when the size of coal is below 100 mesh, the above methods suffer from poor grade and low recovery. The reason for this is that as size decreases, the effects of gravity diminish, and other forces take effect.

Jan 1, 1985