Search Documents

Ground falls (roof and rib) have historically been responsible for nearly 50% of all fatalities in bituminous underground coal mines. In recent years, the number of some annual ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, the twin disasters at Crandall Canyon in 2007, in which nine miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990s, these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents since 2005. Progress has also been made in pillar recovery, where there has been just one fatal incident since 2005. On the other hand, more than 300 miners continue to be injured each year by rock falling from between supports and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities available technologies such as roof screen, rib bolting and inside control roof bolters could reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety.

Jan 1, 2011

By Z. Hyder, A. Urquidez

"INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is located approximately 26 miles southeast of Carlsbad, New Mexico and is the nation’s first underground geologic repository for transuranic (TRU) and TRU-mixed waste (see Figure 1). The WIPP facility was opened for operation in 1999 when the first TRU waste shipment arrived at the WIPP facility for disposal.WIPP facility does not employ typical production aspects of a conventional mine. Instead, the mining focus is on the quality of the excavation to ensure safe disposal of TRU and TRU-mixed waste (Walls, 1991). GEOLOGY WIPP underground repository is mined within a 2,000 feet-thick bedded-halite formation (Salado Formation) (see Figure 2). The WIPP underground repository is located approximately 2,150 feet beneath the surface near the center of the Salado Formation. Geologic criterion and site-selection factors evaluated for the selection of the repository included topography, depth, thickness, lateral extent, lithology, stratigraphy, structure, erosion, dissolution, subsidence, surface water, aquifers, hydrologic transport, climatic fluctuations, manmade penetrations (U.S. Department of Energy, 1980).FACILITY DESIGN Profit did not play a major role in the WIPP’s conception like in a conventional mine. This was due to the extensive amount of additional regulations and safety controls that had to be built into the WIPP facility. Since it is nuclear and hazardous waste disposal facility, it must meet certain federal and state requirements for TRU-mixed waste. One of the major regulatory drivers for the WIPP facility is defined in the WIPP Land Withdrawal Act (LWA). One of the requirements in the WIPP LWA requires the DOE to submit documentation of continued compliance with Title 40 CFR Part 191, Subparts B, and C. These standards are regulated by the Environmental Protection Agency (EPA). The DOE must submit documentation of continued compliance (recertification) with these regulations every five years. In addition to the LWA, the Resource Conservation and Recovery Act (RCRA) is another major regulatory driver for the WIPP facility. Since the WIPP facility is categorized as a “Miscellaneous Unit” under 40 CFR, it must meet extensive environmental performance standards. These standards are defined in the WIPP Hazardous Waste Facility Permit (HWFP). The HWFP defines the terms and conditions that the Secretary of the New Mexico Environment Department has determined necessary to protect human health and the environment (U.S. Department of Energy and Nuclear Waste Partnership LLC, 2015)."

Jan 1, 2017

By H. Mischo, R. Ellmies

Uranium has been mined in Namibia since the 1970s. The worldwide increasing need for energy in the early 2000s has led to the development and opening of a second uranium mine in 2007 and has triggered an increased interest in uranium exploration, often referred to as “the Namibian Uranium Rush.” In all, four mining licenses have been granted by the Namibian Government, which currently has two mines in operation, a third undertaking trial mining and the fourth in project finance negotiations. In addition, highly intensive prospecting activities at additional deposits are at an advanced stage. The finalization of the strategic environmental impact assessment (SEA) on uranium mining in 2010, the first of its kind and scale in the world, has enabled the Namibian government to assess this uranium rush and its tremendous legal, socioeconomic and environmental impacts and to prepare for the different future scenarios conceivable when this article was written in 2011, including both a skyrocketing and a complete breakdown of demand scenario. The Fukushima disaster and plans of the Namibian government to significantly increase royalties and company taxes in 2011 have threatened the market situation, forcing investors to reevaluate Namibian uranium mining projects. However, with the tax and royalty increase initiative since withdrawn, most projects are back on track at this point in time.

Jan 1, 2012

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a silver-white alkali metal that has recently become a target commodity for many junior mining companies. Lithium has a wide range of applications including ceramics and glass, lubricating greases, air treatment, continuous cast mold flux powders, polymer production, and primary aluminium production, but the current popularity of lithium can be attributed to an anticipated increase in demand for lithium ion batteries. The most common lithium-bearing minerals occur globally in pegmatites and granites. Spodumene [LiAl(Si2O6)] is the most desirable economic lithium-bearing mineral due to its high lithium content (theoretical Li2O content of about 8 wt%). However, lithium can also be hosted in petalite, micas, tourmaline, and phosphate minerals. In Canada there are a number of spodumene deposits in Ontario and Quebec at development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and use of electric vehicles. This paper discusses the beneficiation of hard rock lithium deposits, including an in depth review of the use of flotation to upgrade spodumene. A review of the use of dense media separation (DMS), magnetic separation, and roasting as means to process spodumene bearing ores is also discussed. INTRODUCTION Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35%), ceramics and glass (32%), lubricating greases (9%), air treatment (5%), continuous casting mould flux powders (5%), polymer production (4%), primary aluminium production (1%) and other uses (9%) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014). In the 1990s the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced over this period were consumed in the glass, ceramics and aluminium industries. In the 1980s and 1990s there were two major lithium operations in the United States: brine operations at Silver Peak, Nevada, and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, North Carolina. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994)."

Jan 1, 2017

By Ross W. Smith

In recent years there has been a considerable amount of research work done relative to the effect of pretreatment and aging in water on the surface properties of both simple metal oxides and more complex oxides such as the silicate minerals 1-6. Of particular interest is the work of Somasundaran6 who states that after preparing minerals by size reduction and washing with dilute acids "... it is essential to treat it (the mineral) with water in order to remove any effects of leaching itself." Somasundaran also states, "... it is advisable to use a solution close to the point of zero charge for conditioning purposes." Parksl notes that, "Dehydration, dehydroxylation, and increased crystallinity can be expected to decrease the PZC. The presence of anionic impurities or of pH-independent potential determining ions will decrease the PZC. Cationic species will increase the PZC." Healy and Jellett4 believe that in the Zn0-water system "the surface charge of Zn0 in water and each pH is determined by the concentration and adsorption of each hydrolyzed (charged and uncharged) Zn(II) species." Finally, according to Parks 2, "The PZC of an unaltered com¬plex oxide in a system devoid of specific electrolytes is approximately the average of the PZC's of its component oxides... Equilibration with water results in loss of mono and divalent cations by exchange with H+, thus a loss of influence on the PZC by those cations, i.e., a shift in the PZC with time in the direction of that remaining oxide. The present paper investigates the change of point of zero charge (PZC) of a number of simple oxides and several complex oxides as a function of aging time in water. In some cases acid pretreatment of minerals was performed. However, in most cases the minerals were not acid pretreated. In several systems pH change as a function of aging time in water was monitored.

Jan 1, 1972

By R. Raymond

The occurrence and distribution of organic sulfur in coals may be investigated using electron probe microanalysis, scanning electron microscopy, and optical petrography. A general relationship exists between macerals and organic sulfur contents in individual coals: sporinite, resinite = micrinite, vitrinite > pseudovitrinite = semifusinite = macrinite > fusinite. With increasing organic sulfur content of a coal, the total range in organic sulfur content between macerals containing high and low organic sulfur contents likewise increases. Furthermore, the organic sulfur content of the vitrinite in most coals equals the organic sulfur content of the coal. For any individual coal, organic sulfur contents of macerals correlate inversely with reflectance-in-oil measurements, but the amount the organic sulfur contents vary between macerals cannot be calculated based solely on the coal's rank. Formation of pyrite following peatification has no effect on organic sulfur contents of surrounding macerals.

Jan 1, 1986

By Howard S. Avery

The wear resistance of an alloy in heavy mill liner sections may be quite different from that of the same alloy in small balls and other light sections. This fact was established by means of a well standardized laboratory test that was validated for ball mill service. The salient properties of mill liner alloys, including austenitic manganese steels, medium alloy hardenable steels, and abrasion resistance cast irons are described, critically compared, and quantitatively ranked in terms of mill liner service. Where they are tough enough the high-chromium and other martensitic cast irons (e.g. Ni-Hard) promise maximum economy, but their section sensitivity is a limitation. To overcome this an extensive research program studied over a hundred experimental alloys, ranking them for heavy section abrasion resistance by means of the laboratory test. Computer analysis of the results provided a parabolic formula in terms of composition, the apexes of the parabolas providing optimum wear resistance. From the extensive family of parabolas one apex was selected for intensive study in experimental liners, pilot plant production, development of quality controls, and finally full scale production. This is a 19% chromium iron critically alloyed with nickel and molybdenum and hardened by heat treatment. It has excellent resistance to various types of abrasion, but its chief advantage is in heavy mill liner sections, where it has about 25% better abrasion resistance than the best of the quality controlled chilled Ni-Hards. It is also tougher. After production problems were solved, a number of ball and rod mill tests were arranged on a guaranteed performance basis. Two of these, representing about 138,000 pounds of mill liner castings, have recently confirmed in service the superiority that was predicted by the laboratory tests.

Jan 1, 1969

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By G. A. Calboreanu

The deterioration rate of any metal or alloy is increased in a erosion-corrosion application because the passivated surface layer is removed by the solid particles contained in the pumping fluid and the material surface becomes corrosion active again. Numerous attempts were made to engineer a stainless steel with higher hardness and unaffected corrosion performance. Alloys of special interest in such an area are the duplex stainless steels particularly the CD4MCu material which has the capability of being hardened due to its ferrite-austenite microstructure. Unfortunately, the CD4MCu with higher hardness comprises different intermetallic compounds which will increase the corrosion rate. The paper is analyzing the erosion-corrosion performance of a new type CD4MCu with 32% higher hardness and superior wear performance. The corrosion performance of this new alloy is better than the corrosion performance of the common CD4MCu material which the industry could supply. The corrosion effectiveness was evaluated with the Huey test, the potentio-dynamic anodic polarization test and the weight loss test whereas the erosion resistance was established with a low stress ball-on-disk type apparatus. The Wilfley hard CD4MCu material had 39% lower weight loss and 32% smaller volume loss than the common CD4MCu alloy The hardness range of the centrifugal pump parts poured and processed with the Wilfley hard CD4MCu is 320-350 HBN versus 250-255 HBN hardness of the common CD4MCu. After approximately 18 months of experimentation and field testing it was clearly established that the life time of the Wilfley hard CD4MCu is higher than the common CD4MCu and consequently centrifugal pumps were supplied to different customers in North and South America. India and more recently Australia. Sincere thanks to all the A.R. Wlifley & Sons Inc. and Western Foundries Inc. employees who supported and help to implement this work. special thanks to George Wilfley. Dave Cobb. Bill Becker Sr. and Wayne Taylor

Jan 1, 1997

By Patrick Scott, Germán Schmeda, Morgan Mullins, Liam Knudsen, Bradley S. Van Gosen, Carma A. San Juan, Nicholas A. Karl, Jeffrey L. Mauk, Clayton Forbush

The objective of the US Geological Survey’s mineral deposit database project (USMIN) is to develop a comprehensive twentyfirst century geospatial database that is the authoritative source of the most important mines, mineral deposits, and mineral districts of the US. Since May 2017, the project has focused on critical minerals. Data for critical minerals that are produced as products are relatively robust, whereas data for critical minerals that may be recovered as byproducts are commonly of much poorer quality. Similarly, more is known about critical minerals that occur in conventional deposits than where those critical minerals occur in unconventional deposits. For example, rare earth elements occur principally in deposits hosted by alkaline igneous rocks, but there is potential for their production from phosphate rock mining, which is less documented. Lithium (Li) has been recovered from pegmatites and brines, but other Li-bearing deposit types have been delineated that may go into production. Cobalt may be produced as a byproduct or coproduct from a wide range ofmineral deposit types, whereas rheniumis a byproduct of copper ore. Significant opportunities for research exist that could help identify new sources of critical minerals, and may also help increase production and recovery from existing sources.

Feb 8, 2021

By Robert A. Jankowski, J. Drew Potts

The Bureau has identified several ventilation techniques and a water spray application for reducing auger mining dust levels. The dust control methods all work by improving air quantity or flow patterns at the face. Section airflow is maximized by reducing air leakage between entries. Sealing stoppings with brushed- on mortar, containing fiberglass additives, reduces leakage. Heading airflow is maximized by properly installing the brattice curtain and keeping the area between the curtain and rib free from obstructions. The brattice curtains should be hung at least 1.7 m (5.5 ft) from the ribs in 7.9 m (26 ft) wide entries and kept less than 4.6 m (15 ft) from the face. A tight curtain seal is created by using the mine air pressure to force the curtain against the timbers, roof and floor of the mine. Using both a blowing curtain and an exhausting curtain will isolate some face workers from dusty air. The Bureau designed, auger clearer spray system, can be used to force heading air across the active face. Laboratory tests indicate that the auger clearer spray system can increase face velocities by more than 0.5 m/sec (100 ft/min), while using less than 0.13 l/sec (2.0 gal/min) of water.

Jan 1, 1989

By J. Seiter, S. Cox, E. Kim

Mining has always been among the most hazardous of occupations, and with the increasing demand for coal and minerals, safety in mines assumes even greater importance. Worldwide, underground miners are being exposed to noise and respirable dust hazards associated with roof bolt drilling. These hazards are now being understood to cause irreparable damage to the health of miners. The objective of this research was to discover if a polycrystalline diamond compact (PDC) drill bit generates less respirable dust and hazardous noise than a competing tungsten carbide (WC) bit in dry vacuum drilling. In order to control the drill parameters the drilling tests were conducted in a laboratory setting. The results were obtained by determining the quantities of dust and noise generated using each drill bit and analyzing those levels, using monitoring devices and software to collect the data. This paper includes information on the experimental setup, equipment used, drilling parameters, and data collected. Our results indicate that PDC bits produce significantly less noise and dust than WC bits. Our findings can contribute to improving the working conditions of rock bolter operators by reducing noise and dust generation.

Jan 1, 2014

By J. K. Ahlness

The US Bureau of Mines investigated technologies for determining the integrity of in situ leach mining wells. A self-contained trailer-mounted well integrity testing system (WITS) was designed and built to enable rapid testing of well casings for leaks as required by environmental regulations. The WITS utilizes two inflatable packers to seal off the entire casing length or any portion thereof. Water pressure is built between the packers to the desired test pressure, and the presence or absence of casing leaks is determined by monitoring the pressure drop between the packers. A winch and steel cable are used to run the packers in and out of the well. The WITS underwent an industry field test at the Irigaray in situ uranium leaching mine near Buffalo, WY. A total of 37 wells with an average depth of 69 m (225 ft) were tested at an average rate of four wells per eight-hour shift with a two-person operating crew. This represents a 75% time savings and an 83% labor savings compared to the rigid-pipe method previously used at the mine, with which a three-person crew tested an average of one well per shift.

Jan 1, 1988

By ANDREW HOBERT, Maoming Fan

Low-cost and environment-friendly green froth flotation modifiers of plant origin, such as guar gum, carboxymethyl cellulose (CMC), and starch, have been used in flotation of some sulfide and non-sulfide minerals. Certain green modifiers may be used as dispersants, flocculants, depressants, or activators. The functions of green modifiers in froth flotation highly depend on their molecular composition, flotation slurry chemistry, hydrodynamic conditions, etc. This paper will discuss the fundamentals, current applications, and potential new applications of guar gum, CMC, and corn starch in valuable minerals (phosphate, potash, and iron ores) and the unwanted gangue minerals (silica and clay minerals) flotation. In this study, improved flotation performance was achieved using some green modifiers in flotation columns with the more plug-flow environments than in conventional flotation cells approaching perfectly mixed conditions. This is because the hydrodynamic cavitation-generated ultrafine bubbles could help bridge ultrafine particles to form aggregates, promote the formation of flocs, and increase the stability of flocs.

Jan 6, 2022

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for the expensive large-scale tests that are currently being used. A radiant-panel apparatus was used to determine the materials’ relevant thermal characteristics: time to ignition, critical heat flux for ignition, heat of gasification, and mass-loss rate. Three thermal parameters, TRP, TP1 and TP4, were derived from the data, then developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with the thermal and ignition hazards of similar materials reported in the literature and support this approach as a simpler one for quantifying these combustible hazards. Resumen ¦ El objetivo de este estudio fue el desarrollo de un método a escala de laboratorio con el fin de clasificar los peligros de ignición y fuego de materiales comúnmente usados en minería subterránea y la eliminación las pruebas costosas y a gran escala que se realizan actualmente. Se usó un aparato de panel radiante con el fin de determinar las características térmicas relevantes de los materiales: tiempo de ignición, flujo de calor crítico para ignición, calor de gasificación y tasa de pérdida de masa. Se derivaron tres parámetros térmicos de los datos: TRP, TP1 y TP4, luego fueron desarrollados y subsecuentemente usados para clasificar los peligros combinados de ignición y fuego de materiales combustibles, de bajo riesgo a alto riesgo. Los resultados tuvieron una comparación favorable con los riesgo/peligro térmicos y de ignición de materiales similares reportados en la literatura y apoyan este enfoque como uno más simple para la cuantificación de estos riesgos combustibles"

Jan 1, 2015

By Robert D. Thomson

Land use is the single most important element affecting the quality of our physical environment. .The minerals industry is a user of land and by its very nature, directly affects the landscape. Mining is a very visible activity. Producers of sand and gravel, crushed stone, clay, cement and lime operate right at the interface of the public. These production sites must be located near population centers. People are more travel oriented than years ago and through use of the expanded interstate highway system visit remote and little-visited areas. They visit communities on their vacations, places they enjoy on weekends and places they drive past on business trips. Although not residents of these localities, they have a strong interest in changes that occur in the landscape. As a result, the public has a greater concern today about mining and its use of land. From 1930 through 1971, the minerals industry used 3.65 million acres, or 0.16 percent of the land mass in the United States (4)2/. Of the total 3.65 million acres utilized, about 59 percent was accounted for by the area of excavation, 20 percent by disposal of overburden and other mine wastes from surface mining, 13 percent by disposal of mill or processing wastes, and 5 percent by disposal of underground mine wastes; the remaining 3 percent was subsided or disturbed as a result of underground workings. Nonmetallic minerals and fossil fuels each accounted for 43 percent of surface land used during 1930-71; the metal mining industry utilized the remaining 14 percent.

Jan 1, 1976

By John Hillman

The reconstruction of the British mining industry which began shortly after nationalisation in 1947 continued until well into the 1950s with the support of the Government. This support diminished as plentiful supplies of cheap oil from the middle East made many coalmines un¬economic. The planned rundown which followed was foreshadowed in the 1965 White Paper which outlined the financial measures to speed the closure of uneconomic collieries. The decline appeared likely to continue into the 21st century as the role of coal in UK energy requirements became less and less significant. This policy was well on course in 1973 when the oil crisis led to a complete reappraisal of the position. A Government examination in 1974 of the coal industry then supported the National Coal Board's general strategy of major capital investment as set out in its 'Plan for Coal' (1). Plan for Coal aimed at halting the intended decline in the industry's capacity and restoring it to 120 million tons of deep mined output in 1985. The Plan proposed action along the following lines (a) increase output by major Investment in construction at existing collieries with sufficient reserves to give 13 million tons per annum extra output (b) invest in extending the life of existing collieries by gaining access to additional reserves, to give 12 million tons per annum extra output © by sinking new mines, produce an extra 20 million tons per annum. Figure 1 shows the contribution (2) expected from each of the three sources up to 1990/1. The measures taken were expected to offset the inevitable exhaustion of existing pits and provide the additional 40-42 million tons capacity needed to restore annual output in 1985 to 120 million tons. Parallel to this programme for expansion of deep mined output, opencast mining was to produce 10-15 million tons per annum. A recent review however, indicates that new mines are likely to yield only 10 million tons per annum by 1985, mainly owing to the need for public inquiries into proposals for new mining and the resultant fact that planning approval takes 'much longer than originally expected. Nevertheless the objective of 120 million tons deep mined output by 1985 is still considered achievable of means of a greater contribution from existing mines. This programme was originally estimated to cost 2,-56 million dollars at March 1974 prices, out revised estimates of the cost of Plan for Coal indicate that it may now exceed 6,960 million dollars at mid-1977 prices. Plan for Coal includes a substantial investment in new and reconstructed coal preparation plaints. At mid-1977 prices more than 322 million dollars Ls so be invested in coal preparation projects in the UK, at the rate of, about 70 million dollars a year. This rate 3f capital expenditure has been maintained over the past three years and covers investment in a wide range of coal preparation coals for the power station, coking and domestic markets.

Jan 1, 1978

By Ashutosh Kumar Bharati, Rajesh Rai, B. K. Shrivastva, Arunava Ray

Opencast mining method is one of the most productive mining methods available at present, which is generally associated with the removal and handling of a huge amount of overburden material. Hence it imposes a serious challenge of dump slope stability and that too, mainly in the case of internal dumps. The study is primarily focused on the stability of dragline dumps and the subsequent development of a rating system to classify the stability of dragline dump profiles. Initially, numerical simulation is executed through RS2 (Version 9.0) software, which is based on the finite element method. Thereafter, simulation results are used to perform the sensitivity analysis of various geometrical and strength parameters of the dump slope, and the two-factor interaction method is also incorporated into the analysis, this method included the dependency of closest parameters while calculating the sensitivity index, and thereafter, it is converted into the rating of each parameter. The strength parameter like the angle of friction and the geometrical parameter like slope angle of the bench between the coal-rib roof and dragline sitting level are assigned the highest rating value. Based on the overall rating of the dragline dump, the dump slopes are classified into various classes, viz., very safe, safe, vulnerable, unstable, and highly unstable. This classification proved to be handy in the quick estimation of the stability of the dragline dump and also gives an idea of designing optimum and safe dragline dump profiles. The developed classification chart has been validated by the previous research works and has found similar results.

Feb 15, 2021

By J. R. Goode

The first part of this paper comprises a general discussion on refractory gold ores and their mineralogy processing methods now in use are reviewed and test procedures for the important methods are discussed. Factors determining the selection of a process are outlined. The paper includes a survey of production plants using pressure oxidation, roasting and biological oxidation to process refractory ore. The status of processes under development is briefly reviewed.

Jan 1, 1993

By B. Boutilier, R. Mendoza

"First Majestic Silver Corp. (FMS) is a silver mining company founded in 2002 that operates exclusively in Mexico. It has six producing silver mines, one of which is the La Encantada silver mine (La Encantada) located in the state Coahuila. La Encantada is located near the southern United States border and 708 km (440 miles) north of the city Torreon.La Encantada is located in the Sierra Madre Oriental and is a high-temperature carbonate replacement deposit. Mineralization in La Encantada occurs in many different forms such as veins, chimneys, breccia pipes and reefs (mantos). Mineralization is mainly oxides of iron, zinc, lead and manganese, with high concentrations of sulfides at depth relating to two main intrusive events: the Milagros Intrusive and the La Prieta Skarn.Mining began in La Encantada during the 1950s with small vertical shafts, drifts and raises. It focuses on the high-grade silver zones using traditional hoists and extraction methods, before branching into two main separate mining camps: El Plomo and Penoles camp. Penoles, the previous owner, focused mainly on large ore bodies using post pillar cut-and-fill mining method to extract the higher-grade material. Due to the type of ground, irregularity of pillars, and rock conditions, large amounts of high-grade pillars had to be left in situ to ensure the stability of the excavations. The mined-out areas would then be filled with lower-grade material to assist in the stability of the secondary level. These room-and-pillar development entries were 2.5 m x 2.5 m (8.2 ft x 8.2 ft) and spaced every 10 m (32 ft), leaving a vertical pillar of 7.5 m (25 ft). First Majestic acquired La Encantada in 2006. After the acquisition of the mine, the company began the conversion of the surveying reference system from a local grid (Maria Isabel Shaft as 0,0) to the Nav27 coordinate system, and subsequently converted to the WGS84 coordinate system in 2015. Due to the extensive history of the mine, different areas were surveyed with different systems, causing significant challenges when designing the principal extraction levels, pillar heights and ramp locations. To overcome this difficulty, the entire mine was resurveyed and the old workings transposed to the new coordinate system, except for some inaccessible areas due to poor ground conditions or ground collapses. To further ensure pillar height and the safety of the mine workers, probe holes were drilled during the development process."

Sep 1, 2019