Search Documents

By S. Dawson

The Republic of South Africa has become a major producer of opencast coal in recent years. Opencast production commenced in 1970 and by 1977 some 10 million run of mine tonnes were being produced annually, Since then surface mine activity has increased to more than 60 million tonnes which represents approximately one third of the total annual South African? coal production. Whilst a substantial portion of this production is exported, the majority is used in the domestic market, The largest consumer, being the South?\ African Electricity Commission (Eskom), produces most of South Africa's electricity using coal fired power stations,

Jan 1, 1990

By D. F. Malott

The Michigan Department of State Highways makes extensive use of geophysics for subsurface surveying which would be applicable for uses in other fields. Examples of resistivity surveys are given which include a proposed large volume excavation with suggestions for land use after excavation, subsurface evaluation for engineering design, and a subsurface survey for land appraisal. An example of a combined refraction seismic and resistivity survey is shown where the resistivity is used for outlining the unconsolidated soils, while the seismic method Is used to outline bedrock and to evaluate it for rippability. A refraction seismic survey at the bottom of bridge caissons for evaluation of bedrock uniformity and a relative aid In assessing rock strength is reported.

Jan 1, 1968

By M. J. Hannan

Considerable interest has arisen in developing analytical methods suitable for measuring resource commodity substitution patterns. some of this work has applied the Translog method to estimate actual elasticities of substitution. Recent examples incl.uae Privolos and Dunietz (1987), Kopp and Smith (1983), and Moroney and Trapani (1983). Another method, one which has received attention earlier in the work of Fisher and Pry (1970), is that of the logistic or diffusion function. We believe that the latter method has properties suitable for analyzing current problems of material substitution. The present study thus evaluates this method in its original logistic form as well as an extended version incorporating additional explanatory influences. The analysis is applied to copper/aluminum substitution and iron ore beneficiation. Substitution for copper by aluminum is examined in the building wire and cable, and magnet wire end-use markets. For iron ore, the substitution of pellets for sinter is considered for the U. S. market.

Jan 1, 1990

By R. Hedin, M. Dunn

The Pennsylvania Department of Environmental Protection (US EPA 319 program) provided funding to aid a public-private effort in the installation of an environmentally-friendly system to treat abandoned mine drainage at Jennings Environmental Education Center (Pennsylvania Department of Conservation and Natural Resources). Through this cooperative effort among state and federal agencies, mining, excavation, and environmental companies, college and home school students, Girl Scouts, and volunteers, a successful multi-component passive system, readily accessible for upgrades and public education/research activities, was built. 90 people were directly involved in construction of this award-winning system and about 1000 people annually benefit from the educational opportunities.

Jan 1, 2002

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck

"Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27% of the respirable coal mine dust can be attributed to longwall shield movement. Developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine their ability of foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used; compressed air (CA) and blower air (BA). Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For CA foam in 3.3 m/s (3.3 m/s (650 fpm)) ventilation at 3 minutes after application, 98% of agent A was intact, while 95% of agent B was intact on the roof. At 30 minutes after application 94% of agent A was intact while only 20% of agent B remained. For BA in 3.3 m/s (3.3 m/s (650 fpm)) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 minutes after application 74-92% of foam agent A remained, while 3-50% of foam agent B remained. CA foam seems to remain intact for longer durations and is easier to apply than BA foam. However, more water drained from the foam when using CA foam which demonstrates that BA foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control. INTRODUCTION NIOSH personnel have visited many longwall operations at various geographical locations in the U.S., conducting benchmark surveys to characterize current operating practices and dust control measures in use. Sources of respirable dust generated from the longwall face have been identified as: intake (10%), stage loader (20%), shields (27%), and shearer (43%) [1]. Dust generated from the shearer, armored face conveyor, and the stage loader can mainly be controlled by water sprays and increases in ventilation air quantities, however, research has demonstrated limited effective controls for dusts generated by shield movements [2]. One possible approach to mitigating shield dust generation is to apply a layer of water or foam to the shield-roof interface. Once this interface is blanketed with foam or water, dust will be less likely to become airborne and contaminate the airways over the personnel walkways. Though water is an abundant and common dust control measure, roof applications have limited success because water is unable to remain in-place in adequate quantities for the necessary duration between application and shield advance. Past and current testing of foam for material properties has shown that it has longer applicability times, ranging from 10 to 60 minutes [3] and has shown better performance for dust control, ranging from 19-96% improved efficiency over water [4, 5, 6, 7, 8]. The majority of this foam dust control research has focused on dust control efficiency at the longwall shearer or continuous miner cutting drum."

Jan 1, 2017

A bearing isolator is a noncontact, nonwearing, permanent bearing protection device. It has a rotor and a stator, and the two are unitized, so that they do not separate from one another while in use. The rotor turns with a rotating shaft, while the stator is pressed into a bearing housing. The two components interact to keep contamination out of the bearing enclosure and the lubricant in. Bearing isolators do not require lubrication or any particular shaft finish or condition. The best bearing isolators are made of metal, usually bronze. They use a vapor-blocking feature that inhibits the free transfer of vapor contamination when the rotating equipment is cycled on and off.

Jan 1, 2004

By R. R. Kallu

The current 120 psi seal design and evaluation practices are mostly based on simple analytical solutions. Considering the simplistic assumptions and limitations involved in simple analytical solutions and practical difficulties involved in conducting conventional full-scale explosion tests for evaluating 120 psi seal designs, there is a need for developing new scientific methods and engineering practices for design, analysis and evaluation of mine seals.

Jan 1, 2010

By Anna Kate Miller, James J. Brady, Hamza Jaffal, Ritika Sangroya, Chadi El Mohtar, Wing Shun Kwan

"The design of an appropriate pre-grouting program can be the difference between a successful tunnel construction and an expensive on-the-go repair. However, current grout design relies heavily on rulesof- thumb and outdated charts. The geotechnical investigation is rarely targeted towards grouting design and the final grouting decisions are made based on fines content or soil classification. The current paper presents an experimental study performed to determine the optimal grout for a tunnel in soft ground below the ground water table (GWT). The testing program consisted of sieve analysis and undrained static triaxial tests on reconstituted sonic samples. Rheological tests were used to compare the different grout mixes and identify best candidates before performing one-dimensional permeation tests. Pressure and volume measurements during the permeation tests, along with the unconfined compression strength results on the permeated soils, helped evaluate the filtration potential for the different grouts and select the optimal grout.INTRODUCTIONConstruction of the Millwoods Double Barrel Replacement Project commenced in 2009 and was expected to be completed by 2015. To facilitate ongoing city development in south Edmonton, the City implemented construction of a major sanitary trunk network along 91st Street and 30th Avenue. The project involved the design and construction of approximately 1.2 miles (2 km) of 7.8-ft (2,400 mm) sanitary tunnel and 2.1 miles (3.4 km) of 11.5-ft. (3,500 mm) and 9.5-ft. (2,900 mm) storm tunnel. Part of the project also involved the conversion of the existing double barrel storm and sanitary trunk to full sanitary service, and reconnecting the local storm sewers from the double barrel pipe to the new storm tunnel. The tunnels range in depth from 26-ft. (8 m) to 115-ft. (35 m) and are being installed using a one pass system with precast concrete segmental liners."

Jan 1, 2016

By P. Zhang, S. Al-Thyabat

"Phosphate rock contains traces of rare earth elements (REEs) and can be a secondary source of these critical materials as large tonnages of phosphate rock are mined annually. Attention has mostly focused on the extraction of REEs from phosphogypsum, which contains more than 70 percent of the REEs reporting to phosphate concentrate, with only limited work conducted on REE extraction from sand tailings and slime even though they account for 16 percent and 15 percent, respectively, of REEs mined with phosphate matrix.In this work, phosphate flotation tailings were upgraded by gravity separation and froth flotation. Gravity separation was conducted using a laboratory shaking table, while flotation was conducted in a Denver D-12 flotation cell. The concentrated tailings were then leached by nitric acid followed by REE extraction with solvent and ion-exchange resin.The sand tailings were assayed as having 2.6 percent phosphate (P2O5 ) and 198.1 µg/g REEs. It was found that the shaking table could produce tailing concentrate assayed as having 8.6 percent P2O5 and 616 µg/g REEs but with only 20 percent REE recovery, while the froth flotation produced froth concentrate assayed as having 8.1 percent P2O5 and 368.2 µg/g REEs with 63.5 percent REE recovery. Leaching the flotation concentrate with 5.2 M (25 percent) nitric acid followed by extraction with solvent and ion-exchange resin yielded precipitates with REE contents of 0.926 and 0.314 percent, respectively, compared with 0.716 and 0.213 percent when table concentrate was used.IntroductionRare earth elements (REEs) consist of a group of 17 elements: the 15 lanthanides along with yttrium (Y) and scandium (Sc). They are rare not because of their scarcity in the Earth’s crust but because they are rarely found in economic and mineable deposits. REEs are called “seeds of technology” because of their importance to some critical technological industries such as renewable energy, hybrid cars, electronics and batteries. On average, an electric car or a hybrid car contains about 10 kg of REEs (Grasso, 2012; Radhika et al., 2011).REEs are usually categorized into light (LREE) and heavy (HREE). LREEs consist of lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pr), samarium (Sm), europium (Eu), gadolinium (Gd) and scandium (Sc), while HREEs consist of terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), lutetium (Lu) and yttrium (Y). About 200 minerals contain traces of REEs, but only three are considered economically significant: bastnasite, with the formula La,Ce(CO3)F; monazite, with the formula(Ce,La,Nd,Th)PO4; and xenotime, with the formulaYPO4 (Jordens, Cheng and Waters, 2013)."

Jan 1, 2016

By Jack E. Bailey

From a start in 1957, milling 3,000 TPD of copper ore, the Cyprus Pima Mining Company, which is located 20 miles south of Tucson, has expanded its operations four times, and is currently treating over 55,000 TPD of ore.1 The most recent expansion added a 14,000 TPD semi-autogenous concentrator to the operation. Shortly after startup in January, 1972, the semi -autogenous plant exceeded the designed tonnage rate.2 Ore from the mine is delivered to a 54 inch gyratory crusher and is reduced to a minus 8 inch product. From the crusher the ore is stacked on a surge pile and then reclaimed and fed to the two parallel grinding circuits. A 28 ft. diameter by 12 ft. long semi-autogenous mill and a 16.5 ft. diameter by 19 ft. long ball mill make up each grinding circuit. The semi-autogenous mills are in closed circuit with screens and the ball mill circuits are closed with hydro- cyclones. Rougher flotation follows the grinding operation. Concentrate regrinding and cleaner flotation is performed in Mill I, the older mill. The generalized flowsheet is shown in Figure 1.

Jan 1, 1975

Within the research project "Mine Development" funded by the "Austrian Fonds zur Forderung der wissenschaftlichen Forschung (FWF) " (funds for scientific research) between 1991 and 1993 150 underground hardrock mines in Europe, Northern America, Australia and Japan have been visited to analyze their general design and layout. The main aim of the project was to develop strategies for accessing new underground hardrock mines and to establish a mine planning database. The investigation included mines in high developed countries only, with a comparable labor cost situation. This paper presents the results of one part of the project, which deals with investigations into the influence of different parameters on the design of the primary access for a mine.

Jan 1, 1995

By K. Boakye, T. Newman, P. Bláha, M. B. Toelle

"This paper presents a quarry optimization plan using a block model and an in-house development quarry scheduling and optimization software (QSO Expert) to help improve quarry operations at Crystal River. The Crystal River Quarry is an underwater quarrying operation that barges limestone via the Gulf of Mexico, as the main source of raw material to a cement plant in Theodore, Alabama. To improve the quarry operation, an evaluation was completed to optimize the quarry planning and extraction procedures of the quarry. In order to achieve this, additional exploration drilling campaign was implemented, a new block model was re-calculated and the latest version of QSO Expert software was used. The primary economic impact is a higher recovery of limestone reserves; sustainability of resources, corresponding longer quarry life. Secondarily as the limestone is mined underwater and stockpiled above water, drainage reduces moisture content achieving direct cost reduction on limestone shipping. In addition, a considerable reduction in operational cost was achieved due to a significant decrease in consumption of electrical energy, reduced dragline maintenance costs and reduced dragline movements within the operation. INTRODUCTION Holcim is a Swiss-based global building materials and aggregates company. Founded in 1912, the company expanded into France and then throughout Europe and Middle East during the 1920s. In 1922, Holderbank, as the company was then known, expanded beyond the Swiss borders into France. By the end of the decade Holderbank held stakes in Belgium, Germany, the Netherlands, and Egypt (Holcim History 1912-2012) Positions in Lebanon and South Africa soon followed.. Holder bank later expanded in North America in the 1950’s. In the late 1970s and early 1980s, Holderbank continued its expansion in Latin America, Asia and Spain for the first time. The company expanded into Eastern Europe and experienced a boom in Spanish construction preceding the 1992 Summer Olympics. By 1986, Holderbank was the world's largest cement manufacturer. In the 1990s, the company consolidated its European holdings as the American market drove growth. Expansion into Eastern Europe and Russia continued (Holcim History 1912-2012). In 2001, the company changed its name from ""Holderbank Financière Glaris"" to Holcim (short for Holderbank ciment) (Holcim History 1912-2012). Holcim expanded by purchasing Aggregate Industries entering into the United Kingdom for the first time. That year, the company also expanded into India by acquiring a stakes in The Associated Cement Companies (ACC) and Ambuja Cement Eastern. In 2008, Holcim became the largest shareholder of China's Huaxin Cement with a 40% stake. In 2009, they acquired Cemex Australia. In 2014, Holcim and Lafarge announced they had agreed to terms on a ""merger of equals"" valued at nearly $50 billion in 2015. The new company LafargeHolcim based in Switzerland has a manufacturing capacity of 427 metric million tons a year."

Jan 1, 2017

By Howard W. Adam

Mill length was the primary variable investigated in an autogenous pilot mill circuit. The 5-1/2' diameter mill had both pebble ports and 1/2" wide slotted grates. The plus 1/2" mill product was crushed in a cone crusher and returned to the mill feed along with the minus 1/2" plus 4 or 6 mesh fraction. Tests were run with a short mill, inside length of 26-3/8", or diameter-to-length ratio of 2.50 to 1. The same mill was then lengthened to 48-3/8", diameter-to-length ratio of 1.36 to 1. The effect of mill length on circuit product characteristics was studied. Results show that (1) circuit throughput or grinding rate is lower per foot of mill length in the longer mill, (2) the long mill product is finer than the short mill product, and (3) KWH per ton of circuit product is slightly higher with the longer mill; however, KWH per ton of minus 200 mesh material (finer fraction) produced is essentially the same in the long mill as the short mill, It is not known whether the relationships found for the pilot mill are valid for commercial size mills.

Jan 1, 1973

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

By S. Murdock, R. L. Fleischer, H. W. Alter, J. E. Gingrich

The use of solid state track deters allows totally passive, integrating measurements of 222Rn (radon) or of 220Rn (thoron) plus radon. A track-detecting solid is placed in a holder that is closed by a selective membrane and exposed to the atmosphere of interest to produce an accurately time-averaged record over times of interest that range typically from a week to a year. By selection of the proper membranes, dosimetry can be done for radon or for the sum of radon and thoron. A different membrane is appropriate for measuring radon under humid conditions such as are found in the ground. Large numbers of measurements have been made with these systems both in the ground, where radon levels are high, and in indoor environments, where levels are orders of magnitude less. Calibrations have been carried out at both high and low concentrations of radon. New results in the air at the site of the Shirley Basin mine and mill give reproducible results with month-long integrating periods. The off-site background levels are in the range 0.7 to 1.0 pCi/l (26-37 Bq/m3). The average yearlong on-site level is 1.5 pCi/l (56 Bq/m3); at the mill it is 2.6 pCi/l (96 Bq/m3); and the level measured at the backhoe in the open pit mine is 3.9 pCi/l (144 Bq/m3). The region of significantly elevated radon levels is confined to a radius of 1.6 km of the mine and mill. All of the on-site radon concentrations are less than but comparable to the typical values found in the living areas of modern energy-efficient homes.

Jan 1, 1981

By O. Ofor

Coal fines of less than 0.5 mm particle size, discarded as too fine for gravity separation, were subjected to flotation tests at varying pH and temperatures using modified dosages of kerosene as oil phase and methylisobutylketone (MIBK) as frother. Optimal coal recovery of over 74% was obtained using 200 kg kerosene and 4 kg MIBK per ton of coal fines at a pH of 9.7 and an ambient temperature of 26° C. The coal concentrate obtained under these optimal recovery conditions assayed 9.10% ash, 0.35% sulfur and 0.011% phosphorus, representing reductions in the ash, sulfur and phosphorus contents of approximately 75%, 43% and 8.3%, respectively. Its gross calorific value was 32.9 MJ/kg, its percentage of volatile matter measured 30.6 and the fixed carbon content was 66.3% (d.a.f). Caking tests showed the optimal concentrate has a standard welling number of 1 and is a Gray-King coke type C. These results show that the optimal flotation product could be utilized for such industrial purposes as steam raising or for processing in gasworks, but it would be unsuitable for metallurgical coke production.

Jan 1, 1993

By Verya Nasri, Mehdi Bakhshi

"Fiber reinforcement has emerged as an alternative to steel bars in precast concrete segments due to advantages such as saving cost and reducing production time while developing a more robust product with improved handling and long-term durability. ACI recently drafted a new report as the first design guideline on FRC tunnel segments to provide specific guidance for this emerging technology. ACI document offers general information on the history of FRC precast segments from tunneling projects throughout the world; a procedure for structural analysis and design based on governing load cases, and a description of the material parameters, tests and analyses required to complete the design. This paper summarizes the design considerations in this ACI guideline prepared by the authors of this paper as the main contributors. Application of this guideline to design of a tunnel with an internal diameter of 5.5 m (18 ft) results in elimination of steel bars.INTRODUCTIONPrecast concrete segments are installed to support the tunnel excavation behind the Tunnel Boring Machine (TBM) in soft ground and weak rock applications. The TBM advances by thrusting off the completed rings of precast concrete segments that provide both the initial and final ground support as part of a one-pass lining system. These segments are typically designed to resist the permanent loads from the ground and groundwater as well as the temporary loads from production, transportation and construction. Tunnel segments are generally reinforced to resist the tensile stresses at both the Serviceability (SLS) and the Ultimate Limit States (ULS). With traditional rebar, a significant amount of labor is needed to assemble the cages and place the rebar, which results in higher production costs.Fiber Reinforced Concrete (FRC) can be used to enhance the production, handling, and placement of precast concrete segments. This is because of the uniform dispersion of fibers throughout the segment to include the concrete cover, which is very advantageous for resisting the bursting and spalling stresses. These stresses develop as a result of the high loads induced on the segments during the TBM jacking process. The presence of fiber in the concrete matrix helps mitigate against unintentional impact loads during segment handling and tunnel construction operations."

Jan 1, 2016

By J. G. Pippenger

Rio Tinto Coal Australia (RTCA) developed Meandu Mine in Queensland, Australia in 1983 to supply thermal coal to the adjacent newly constructed Tarong Power Station (TPS). In designing the mine, RTCA selected Meandu?s best economic reserves for a 25-year life based on station owner Tarong Energy Corporation?s (TEC?s) estimated life for TPS. That 25-year plan changed dramatically in the early 2000s when TEC approved life extensions to TPS?s four existing units plus construction of a fifth unit. After reviewing Meandu?s remaining reserves, RTCA decided the nearby Kunioon reserve offered the more economic option for maintaining deliveries beyond 2010. Those plans changed yet again in 2007 when TEC chose to purchase the Meandu Mine and nearby reserves rather than extend RTCA?s contract. TEC then selected Thiess Pty Ltd (Thiess) to continue operating Meandu until the new mine at Kunioon could be developed.

Jan 1, 2011

By Peter B. Knuckey

1, Introduction Location Kalengwa mine is located in the North Western Province of Zambia, 402 kilometre by unpaved road to the west of Kitwe, which is roughly in the centre of the Zambian Copperbelt, well known as one of the world's centres of copper mining. Its position is illustrated on the map of Africa in Figure 1 and on the map of Zambia in Figure 2. It is a mine of Roan Consolidated Mines Limited whose other properties, Mufulira, Luanshya, Chambishi and Chibuluma Mines, are all located on the Copperbelt. It is managed by the Chibuluma Division of the company. The rate of production from Kalengwa will vary from 12 000 to 17 000 tonnes of saleable copper a year over the next six years. Kalengwa did not exist as a place until the first prospecting parties and later the mine became established and the early working population was recruited entirely from small villages in the surrounding area as much as thirty miles away. The mining area consists of fourteen mining locations amounting to 3.35 square kilometres and the land may be used for any purpose connected with mining, including housing, wood cutting and other utilities. The whole area is, except for minor undulations, a fairly flat plateau with main rivers running from north to south and flood basins known as "dambos" located in a general east west direction. Vegetation is, with the exception of the grassy dambos, temperate forest with relatively light undergrowth. Game of great variety is prolific, as is the associated tsetse fly.

Jan 1, 1971

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques have been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

Feb 23, 2014