Search Documents

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. They are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations.Cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance of having proper stability in cyclone operation while implementing any plant-wide optimization strategy.One of the key challenges in cyclone operation is that cyclones are highly sensitive to changes in operating conditions and are affected by process fluctuations such as feed pressure, solids concentration and flow rates. Fluctuations in cyclone feed characteristics lead to unstable cyclone performance which affects mineral liberation. For such an impactful unit operation, cyclones have historically been under-instrumented in an otherwise highly instrumented process plant. Traditionally, mill operators have relied on visual observations of the apex discharge to determine the operating state of the cyclones. Visual cues corresponding to the different cyclone operating conditions have been discussed by Neesse et al. (2004) as shown in Fig. 1."

Jan 1, 2014

By G. Folmo

Allis Mineral Systems' GRATE-CAR agglomeration/induration/reduction process is currently being operated to process ilmenite at Tinfos Titan & Iron KS in Tyssedal, Norway. In this process, balled ilmenite concentrate is fed to a traveling grate where pellets are dried and preheated, using fully oxidized kiln exhaust gas. Hot preheated, semi-indurated pellets are fed directly to a ported kiln where reduction of the ilmenite's iron oxide fraction occurs in the presence of lump coal. The reduced pellet sand coal char are discharged from the kiln to an indirect rotary drum cooler. Cooled pellets and char are screened and magnetically separated prior to their further processing in a downstream smelting operation. The pellets are melted and the titanium dioxide and iron are separated. Operation commenced in late 1986.

Jan 1, 1992

By Fred Pena

Cyprus Pima Mining Company is located in the Mineral Hill District of southern Arizona, approximately 22 miles south-southeast of Tucson. Cyprus Pima Mining Company is owned 50.01% by Cyprus Mines Corporation, 24.99% by Utah International Incorporated, and 25% by Union Oil Company of California, with Cyprus having the management responsibility. Cyprus Pima's history has been one of continued expansion from an initial plant of 3,000 TPD in 1957; 6,000 TPD in 1963; 18,000 TPD in 1966; 36,000 TPD in 1967; and 53,500 TPD in 1972. The major reason for Expansion IV was that a large volume of low-grade ore had to be moved to get at a higher grade ore in the course of proper pit development. With mining costs already defrayed, this relatively hard, low-grade material became economically profitable for subsequent milling and concentrating treatment. Similar material previously stockpiled was available for ore treatment. In an effort to meet the continuing search for lower unit costs, the largest milling and concentrating equipment had to be examined. The management of Cyprus Pima Mining Company began investigating autogenous, and semi-autogenous milling in 1964 when two carloads of ore selected from the Cyprus Pima pit were sent to the Koppers--Hardinge Operation at York, Pennsylvania for testing. One car contained approximately 40 tons of hard arkosite and the other contained approximately 40 tons of ore classified as soft Hornfels. The purpose of the testing was to determine the amenability of both ore types to autogenous or semi-autogenous grinding.

Jan 1, 1974

By NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

Due to the growing market of Electric Vehicles (EVs), there is a rise in battery demand. Nickel can be used as a potential element in cathode for lithium-ion batteries. Nickel can provide thermal stability, high energy density, and conductivity in cathodes of lithium-ion batteries. Low-grade chromite overburden from Sukinda mines contains less than 1 wt% of nickel, which can be utilized to extract nickel. Recovery of nickel from such low-grade overburden can help in value addition. The present study provides deeper insight into the aspects of extraction of nickel product derivatives (NPDs), mainly mixed hydroxide product (MHP), through the hydrometallurgical route. The current study focuses on extracting nickel and cobalt from a mine overburden with 0.41% nickel with major silicate gangue. MHP can be processed further for nickel sulfate production, a potential raw material for cathodes in EV batteries. The study discusses a process flowsheet to recover nickel and cobalt from overburden through atmospheric leaching with pre-calcination. It is observed that the step of pre-calcination improves the effective recovery of nickel from overburden. The leaching reactions are effective at a temperature of 90 °C and 1 atmosphere pressure. The orthophosphoric acid was used as a lixiviant for the selective recovery of nickel and cobalt from overburden. Recovery of nickel and cobalt obtained at optimum conditions is 84.0% and 39.9%, respectively. The iron impurity in the leachate solution is 1.27%. It is concluded that the process with pre-calcination along with acid leaching is effective for extracting nickel and cobalt at atmospheric pressure.

Dec 28, 2023

By Ashley Woodward, S. Katharine Hammond, Mayela Padilla-Salas

This paper presents a scalable framework for worker safety assessments. The paper focuses on uranium mine reclamation in underserved communities, specifically Cove Chapter of the Navajo Nation. By integrating field observations, OSHA data analysis, systems mapping, and a hierarchical occupational health pyramid, this framework identifies site-specific hazards while addressing broader socio-cultural dynamics. The approach improves upon existing safety programs by suggesting actionable, locally sensitive solutions that prioritize higher-order controls such as hazard engineering interventions and administrative controls. This study contributes to enhanced worker safety, efficient environmental restoration, and engagement in marginalized communities with abandoned mine lands.

Feb 22, 2026

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce risks of coal dust-fueled explosions. The goal of this NIOSH study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust (<75 µm diameter) in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity. Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing, and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle is operated at high fluid pressures to produce smaller droplets and move more air. These findings can be used to select sprays and design spray arrays to control airborne float dust over the entire longwall ventilated opening. INTRODUCTION Coal mining processes produce airborne dust that naturally deposits on the floor, roof, and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 microns in diameter, are deposited in return entries of coal mines and can be re-entrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; NIOSH, 2006). These particles are also those most likely to participate in coal dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (CFR, 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal dust-fueled explosions. Water sprays are both effective and widely accepted as a method for controlling underground coal mine dust. In fact, water sprays are considered to be the most economical and technically feasible means of reducing dust concentrations in underground coal mines (Courtney and Cheng, 1977; Barker and Humphreys, 1996). Sprays are used in several ways to control dust in mining processes: inhibiting dust formation, immobilizing dust to prevent it from becoming airborne, and capturing airborne dust (Cheng, 1973). Reductions in airborne dust concentrations have frequently been attributed to inertial impaction between water droplets and dust particles, forming larger agglomerates which then quickly precipitate out of the airstream (McPherson, 1993). Inertial impaction activity is generally accepted as the major capture mechanism for airborne particles larger than 0.5 µm in diameter. It is this mechanism that is evaluated in this study."

Jan 1, 2017

By Peter W. Lipman

In the Rocky Mountain region, variations in Tertiary mineralization correlate with changes in tectonic setting and associated igneous activity that can largely be related to tectonics along the west boundary of the American plate. Successive settings include compressional tectonics and associated continental-arc igneous activity; transitional igneous types associated with intra- and back-arc extension; and basaltic or bimodal basalt-rhyolite assemblages associated with Basin and Range extension in- ward of a growing transform boundary between Pacific and American plates.

Jan 1, 2013

By J. L. Bellanca, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not constitute endorsement by NIOSH. ABSTRACT Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which presents an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders' evaluations. The study includes considerations for safe technology integration. INTRODUCTION Striking, pinning, and crushing accidents related to mobile machines continue to be a major concern in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) linked 22 of the 75 underground mine fatalities reported between 2011 and 2015 to power haulage [1]. The Mine Safety and Health Administration (MSHA) asserts that proximity detection systems for mobile machines (mobile PDSs) could help to prevent these types of fatal injuries [2]. Mobile PDSs use a collision avoidance technology that allows the mine to establish hazard zones and employ electromagnetic sensors to detect workers equipped with a miner-wearable component (MWC) working near these mining machines. The authors characterize a mobile PDS as an automated technology, because—in line with Lee & See’s [3] definition of automation—a mobile PDS actively “selects data, transforms information, makes decisions, or controls processes” (p. 50). When the system detects workers in the established hazard zones, it issues alerts and slows or stops the mobile machine. Even though a mobile PDS may be a viable and promising safety solution, there are still a number of questions regarding how well this automated technology will fit with mining tasks and conditions. Using a mixed-methods approach, the current study explored factors that influence the fit of mobile PDSs in the underground mining environment.

Jan 1, 2019

By Ralf Plinninger, Pafos Busch, Richard Gradnik

This paper presents the details of the Bad Bergzabern tunnel project. This tunnel is the main part of the B427 federal road bypass, intended to improve the regional traffic infrastructure and to reduce the traffic load in the historic city centre of the health resort Bad Bergzabern. Located in the south-western part of Germany, the project area is situated at the eastern margin of the so-called Palatinate Forest, a low mountain region of mainly triassic sediments with a complex and variable geological history. The German federal government, represented by the office of mobility of Rhineland- Palatinate, awarded the contract to BeMo Tunnelling, a specialized Tunnelling company with a long history of innovation and success in NATM tunnelling. The contract includes the construction of two separate tubes with a length of approximately 1,44 km (0.9 mi)—the road (main) tunnel with a cross section of 101 m2 (1,090 sq ft) and a parallel rescue tunnel with a cross section of ca. 23 m2 (250 sq ft.) Both are connected by six cross passages. Tunnels and cross passages are excavated according to the principles of the New Austrian Tunnelling Method (NATM). Due to BeMo Tunnelling’s technical expertise and capabilities, the project team was able to engineer a speed-up concept that saves money and time for the construction team and client. This paper presents the innovative approach BeMo Tunnelling made to optimize the execution of the tunnelling works and the challenges the project team is facing with regard to a complicated geological situation, countermeasures against an increasing effect of climate change and volatile prices for construction materials.

Jun 13, 2023

By L. M. Sandoval, R. Kaunda, C. N. Vasquez, S. C. Falcon

Artisanal and small-scale mining (ASM) involves a wide range of practices, from highly informal and minimally mechanized mining operations with predominantly manual work to formal practices carried out by small but high-tech industrial mining operations [1]. ASM may be a traditional practice, with skills passed from one generation to another. It can be an important driver of local economic development, while simultaneously contributing to a complex array of positive and negative socioeconomic and environmental impacts. There are more than 100 million artisanal and small-scale miners in 80 countries worldwide, and they supply around 20% of the worldwide gold production [2]. According to the Peruvian Ministry of Energy and Mining (MINEM), in 2020, 32% of fatal accidents in formal (legal) Peruvian mining operations were caused by groundfall events [3].The lack of resources, knowledge of best practices in health and safety, and insufficient equipment used in ASM make the probability of suffering work accidents very high. Furthermore, groundfall is one of the main causes of accidents and injuries in underground mines around the world [4], and it is also a concerning problem in ASM, where the associated fatality rate is similarly high. Unfortunately, a proper record of accidents in ASM is not kept, so an estimate of the actual number of groundfall accidents cannot be accurately developed [5]. Currently miners rely on empirical and observational tools acquired through previous experience to assess groundfall risks. The risks for artisanal miners can tend to be significantly greater than risks for those from the mining industry. This is due to the lack of regulation of ASM, which tends to operate outside the legal framework and the regulations lack of enforcement in force for occupational health and safety regulations.

Mar 2, 2022

By Ali Kazmi, Wern-ping N. Chen

A load rating procedure was performed to evaluate safe load capacity of the Port of Miami Tunnel (POMT), FDOT Tunnel No. 871071 SR 887. The rating procedure performed on a total of eleven stations beneath roadways and with fill depth less than the tunnel exterior diameter (42 ft). Calculations on tunnel sections passing beneath roadways were performed to evaluate the structural response of the sections subject to moving vehicular loads, dead load, and earth pressures. Ratings were performed in accordance with AASHTO and FDOT guidelines. The procedure considered two types of vehicles (HL-93 and FL-120) and two rating levels (Design level and Permit level). As part of HL-93 vehicle, Tandem load was also considered for rating, separately. For HL-93 and HL-93 Tandem, inventory and operating level ratings were performed. The results show rating factors are high. The minimum rating factor is 16.8 using Inventory truck HL-93. For Permit level using FDOT FL-120 truck the minimum rating factor is 6.9. As can be seen, rating factors are higher than comparable analysis for bridges. This paper explains how the procedure can be implemented for tunnels and evaluates the rating results.

Dec 1, 2022

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"NIOSH recently completed a 15-month study at an underground limestone mine crusher booth which evaluated three research parameters: (1) the effectiveness of a single-filter filtration and pressurization system for improving the air quality inside the operator booth, (2) comparing the effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) evaluating the use of three different pressure monitoring devices to determine the performance of the filtration and pressurization system over time. The protection factor was quantified monthly using particle counters in the respirable dust range (0.3–10 µm), and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static conditions and after outlier removal, the single-filter filtration unit installed offered a protection factor between 8 and 216, depending on the filter type and loading condition. The particle counting analysis shows that the ? > 95 filter offers a protection factor greater than 4-times that of the ? > 99 filter when evaluated over 60 minutes. The booth pressure monitors provided data that proved to be a valid indicator of system performance over time. INTRODUCTION Designed and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from physical hazards, such as flying rock, debris, and noise, as well as a more comfortable environment in regards to temperature and humidity [1]. But while it may be easier to quantify whether the A/C unit is working (measuring the temperature) or observe whether the cab offers protection from flying debris, it can be somewhat more difficult to quantify its performance in reducing respirable dust hazards. For over 15 years, NIOSH has been conducting applied research to improve the air quality inside of enclosed cabs of mobile equipment [2-5]. This work has led to the identification and mathematical modeling of enclosed cab filtration systems [6]. The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms [1, 7]. Stationary enclosures are similar to enclosed cabs; however, the volume of the work area can be significantly larger. In addition, workers who perform their duties in stationary enclosures tend to stay within the room for a greater percentage of the day, as opposed to workers on mobile equipment who may enter and exit frequently. Structural integrity can be easier to maintain as well, as there is typically less vibration and stress placed on these compartments as compared to mobile equipment. In addition to offering protection from dust and flying debris, enclosures must ensure that workers have a healthy supply of fresh air to avoid elevated levels of CO2, which are known to cause headache and dizziness, impairing cognitive function. The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) states that enclosures should have no more than 1,100 ppm of CO2 when outside levels are 400 ppm [8]. In addition, the American Society of Agricultural and Biological Engineering (ASABE) recommends a minimum airflow for enclosed cabs of at least 42.5 m3/hr (25.0 cfm) per person [9] to ensure an acceptable level of CO2."

Jan 1, 2017

By F. Habashi

Chile is at present the largest copper and rhenium producer and was before World War I the largest nitrate producer. She is also an important producer of lithium carbonate and molybdenum oxide. An important event in the history of the country is the Pacific War of 1879-1883 in which she acquired the northern provinces initially belonged to Bolivia and Peru. In 1888 Chile annexed Easter Island. The Chilean mineral and cultural history is briefly reviewed together with the people who contributed to her development. The present report is the result of a number of academic and industrial visits to Chile during the period 1992 to 2009.

Jan 1, 2011

By S. R. Titley

Carbonate-hosted massive sulfide (60%) ores of the western Cordillera compose a distinct class of deposits although they vary widely in detail and perhaps genesis. They have been important sources of lead, zinc, copper, silver, gold, and more rarely, molybdenum, tin, and tungsten in complex mineral assemblages usually dominated by pyrite. They occur as concordant stratiform bodies, as discordant mantos, and as chimneys crossing tens of meters of section; many are associated with faults and breccia bodies. Environments of formation of carbonate hosts range from craton basin to shelf with ages from Proterozoic to Cretaceous; in many instances, dating has shown mineralization to be significantly younger than hosts. Temperatures of formation determined for many deposits are high (200°-400°) and many districts are centers of igneous activity manifested by dikes, sills, and stocks. However, direct cause and effect relationships have been difficult to establish. Many important problems attend the renewed interest and study of these deposits and include questions of metal-sulfur sources, metallization processes and histories, geological controls at all scales, and relationships to broader patterns of metallogeny.

Jan 1, 1985

By Peter Keppler, Charles Jackson

WHY DO AN AUDIT? There is increased enforcement of environmental laws and regulations at State and Federal levels with attendant steep fines and even the possibility of jail sentences. We are all aware of environmental and public health and safety incidences (i.e., Love Canal, Bhopal) which have led to stringent laws and regulations (i.e., CERCLA, RCRA, SARA). In some cases, the courts have specified that a company institute an audit program as a condition of settlement of claims which related to lack of environmental control. The U.S.EPA issued an Environmental Auditing Policy Statement in the November 8, 1985 Federal Register (pp. 46504-46508) which encourages the use of environmental auditing by regulated entities. Elements of what EPA considers to be an effective environmental auditing program are outlined and briefly explained. These factors combine to indicate why there is a growing number of companies which have instituted an audit program. Briefly, the program can and should be used to monitor compliance with environmental regulations and corporate policy, to prevent violations, to improve policies and procedures, to raise the level of environmental awareness, to encourage communication among operations and all management levels about environmental problems, and to measure risks and control costs. AMAX Inc. has had an environmental audit program since the early 1970&apos;s. The AMAX Environmental Affairs Department, working with the Law Department, oversees and coordinates environmental audits and analyzes the findings which an audit reveals. Facilities are audited on a regular schedule; those having the greatest potential for environmental liabilities are audited at least annually; other facilities are audited less frequently. The question of who performs the AMAX audits was settled in favor of the audit team being independent of personnel from the facility being surveyed. Other methods of auditing could be the following: - Independent contractor (Appendix A) - Combination of independent contractor and in-house staff - Self-audit by site personnel The merits and demerits of who should conduct the audit can be analyzed to suit your particular needs. Next you need to decide on the procedure for the audit and the form for reporting and follow up. Environmental publications referenced in Appendix B can be helpful to you at this point. After deciding on the form of auditing, a schedule is prepared and followed to the closest extent possible. This schedule should be published and distributed to the sites so facilities know when they are being audited. This is not designed to be "a game of hide and seek." Various elements of the AMAX Audit Program are as follows: Team selection Pre-visit preparation Site visit Exit interview Report Using the audit Follow-up Team Selection The usual make-up of the team is the audit manager, the environmental specialist who normally provides assistance to the site or has knowledge about the operation, and a legal representative if his or her schedule allows. The legal representative will review the findings of the audit team if a personal visit is not timely or necessary. Size of the team can be expanded, but a minimum of the audit manager and the environmental specialist is best. Two sets of observations are better than one. The environmental specialist can also provide the rapport which is beneficial to creating the appropriate tone so that the site people will be as cooperative as possible. This is not to be an antagonistic exercise.

Jan 1, 1991

By Robert R. Beebe

At first glance, mineral processing on an industrial scale might seem entirely in the realm of macro-engineering, with large machines operating on minerals and rocks to achieve size reduction, classification, chemical treatment, separation and dewatering. These operations must be conducted on a large scale to be of practical interest. But the machines and processes may not be designed and operated to take fullest advantage of micro-engineering factors. At the same time, idealized designs based solely on micro-engineering research may require adjustments to gain the desired results in the larger scale, operational context. Using micro-engineering research in this way allows the design and implementation of more efficient versions of the machines and processes currently used, while aiding the revolutionary developments unlikely to come from macro-engineered, trial-and-error solutions. Thus, from an industrial viewpoint, micro- and macro-engineering are complementary functions.

Jan 1, 1992

By Feng Liu

"With seven new applications for plans of work for exploration in the international Seabed Area approved by the Council during its twentieth session of the International Seabed Authority, 26 total approvals have been made by the Council up to date. Among them, three contracts were made with COMRA. On 8 August 2014, China Minmetals Corporation submitted another application to the Authority for approval of a plan of work for exploration for polymetallic nodules in the Area, which is also sponsored by the Government of the People’s Republic of China.China is one of the main contributors to the international seabed regime. The Presentation will describe China’s activities in the Area, such as exploration, technology development, environmental protection and policy making.JIAOLONG is a submersible with capacity of 7000 meters. JIAOLONG’s sea trials were carefully made in 4 years, from 2009 through 2012 and it successfully dove to a depth of 7062m in June 2012 at Mariana trench. A so called "Test Application Phase" started thereafter, and is planned to last for 3-4 years. Two cruises and 4 legs have already been made since then. A wide-range of findings were obtained during dives in South China Sea, and in COMRA’s Exploration Contract Areas for polymetallic nodules and cobalt-rich ferromanganese crusts. This presentation will reveal the colorful findings."

Sep 1, 2014

By Gökhan Çevikbilen, Ümit Karadoğan, Sevde Korkut, Berrak Teymur

This study proposes a methodology for dewatering of mine waste using a multistage process, combining geotextile tubes and anionic polyacrylamide (PAM), which accelerates the recycling process of water for aggregate mine waste facilities. For this purpose, waste from a rock quarry located in Istanbul was investigated. Flocculation tests revealed that the use of anionic PAM at an optimum dosage reduced sedimentation time and decreased turbidity. The compatibility of geotextiles and mine waste conditioned with different dosages of the effective PAM was evaluated by rapid dewatering tests, considering the water content of the filter cake, amount of infiltrated solid content, and rate of filtration. Geotextile dewatering tests were also performed on PAM-free and conditioned suspensions. The dewatering process was optimized by the use of a geotextile tube in two stages: (i) on the unconditioned suspension and (ii) on recovered PAM-conditioned leachate. Directing PAM-free non-hazardous soil-based material obtained in stage i to alternative beneficial uses is suggested, to minimize the volume of waste. Furthermore, recycling of the effluent obtained at the second stage of the proposed method will ensure more efficient water reuse

Sep 29, 2022

Sequential and evolutionary changes through time are recognizable in many, perhaps most major families of ore deposits and their geological environments. These changes are additional useful indicators of the evolutionary history of the earth and its tectonic processes. They are important in mineral exploration because they involve consideration of time as a fourth dimension, thereby indicating the most favorable ages, rather than types of rock for investigation. Many of the changes are analogous to those recognized in faunal evolution. Some primitive, unspecialized types of ore deposits occur nearly unchanged through rocks of widely differing age. Others diversify into several, more specialized variants, whereas still others become extinct. The place of these is taken by new, younger types, some of which undergo sudden proliferations and later diversifications of their own. In Archean greenstone belts irrlportant iron, nickel, gold, and base metal deposits occur co-regionally, but in different stratigraphic positions in the same, thick volcano-sedimentary successions. Here their close temporal and spatial associations suggest common genetic exhalative hydrothermal processes. The massive base metal sulfide family of ore deposits provides an excellent example of evolutionary changes, exhibiting distinct variations through both time and space. Deposits belonging to this family span the entire range of time, occurring in rocks of ancient Archean to Recent age, and specific types within the family also span the entire range of spatial environments from ensimatic to ensialic. Moreover there are possible evolutionary metallogenic links between certain types of massive base metal sulfide deposits and other important base metal ores, noteably Mississippi Valley-type and porphyry copper deposits.

Jan 1, 2013

By Jr. Raleigh

As part vi the development of the Coal Quality Expert (CQRN) --a computer program capable of predicting the impacts of coal quality on power plant performance, costs, and emissions control--several nationally important coals are being characterized to augment the coal quality database associated with the software. The project is sponsored by the U.S. Department of Energy and the Electric Power Research Institute (EPRI) under the Clean coal Technology Program. Since 1989, CQ Inc. (a subsidiary of EPRI) has characterized seven bituminous coals from Alabama, Illinois, Kentucky and Oklahoma and six sub-bituminous coals from the Powder River Basin (PRB) in Montana and Wyoming. Coals from the PRB region--being burned more frequently in Midwestern and southern power plants to reduce emissions of sulfur oxide compounds--can sometimes contain significant concentrations of potentially toxic elements. Although no limits were imposed on air toxics emissions from fossil-fuel fired utilities by the Clean Air Act Amendments of 1990, future regulations may be implemented at the conclusion of Federally-mandated emissions studies. One possible result is that any increased utilization of coals, including those from the PRB, may depend on the potential for removing toxic trace elements prior to combustion.

Jan 1, 1993