Search Documents

By L. Harris

The Yanacocha project is the first foreign investment in Peruvian mining since Cuajone during 1976. Three years after the project began, it has become the largest producer of gold from heap-leach operations in the world and the top producer in Latin America. The success of Minera Yanacocha SA (MYSA) opens a new chapter in Peruvian mining with the exploitation of its widely spread gold deposits. And it has attracted the interest of foreign investors in Peru’s mineral resources. Construction began on Aug. 1, 1992. The first gold bar was poured on Aug. 7, 1993 from ore from the Carachugo Mine. During 1993, Minera Yanacocha produced 2.5 t (81,000 oz) of gold and 9.4 t (304,000 oz) during1994 (40% above budget). Production was expected to exceed 15.5 t (500,000oz) during 1995 with the start-up the Maqui Maqui Mine.

Jan 1, 1996

By Y. Wang, E. Forssberg, A. Johansson, B. Chan

A super-conducting high gradient magnetic separator with matrix vibration in dry separation mode is a powder purification device, which has been used to remove weakly magnetic impure particles from fine calcite powders below 53 µm in this study. A fundamental question concerned is the evolution of the matrix clogging under gas-solids loads. This paper presents the improvement of the separation selectivity using a method of mechanically based vibration on the matrix in the separator. The functions of the matrix vibration are discussed. The results indicated that the mechanically based vibration on the matrix within a high intensity magnetic field while a feed was introduced in an air stream, was found to be effective for the dry purification of fine powder materials.

Jan 1, 2001

By T. Johnson

Mining activity in a number of metal ores has been running quite high over the last few years. In particular, those metals that employ acid functional extraction processes such as copper, nickel, cobalt and uranium have been particularly active. The world?s largest nickel mine ? the massive $4.76 billion Ambatovy nickel mine on the African island nation of Madagascar is nearing completion. When it reaches its full production capacity in 2013, the mine will produce 60,000 MT/yr of nickel and 5600 MT/yr of cobalt. Coming on the heels of the Ambatovy project is the Long Harbour Processing Plant in Newfoundland, Canada which will process the ore from Vale?s Voisey Bay mine in Labrador. Voisey?s Bay is expected to generate more than 50,000 MT/yr of nickel ore when it starts up in 2013. Next up will be the Boleo project in Mexico on the Baja peninsula. When commissioned in 2013, the $1.4 Billion Boleo project is expected to produce 60,000 MT/yr copper, 3100 MT/yr cobalt, 36,000 MT/yr zinc and 100,000 ? 250,000 MT/yr manganese carbonate.

Feb 27, 2013

By Brent K. Nelson, D. Lee Petersen, Charles R. Nelson

INTRODUCTION Tunnels are commonly constructed in the very weak St. Peter sandstone in the Twin Cities area of Minnesota. Historically, core recovery in this weak sandstone was very small in the critical weaker strata resulting in little preconstruction information on the ground conditions. Improved core recovery techniques have been utilized for recent projects, allowing rock quality rating methods to be developed for the recovered core. Down-the-hole tests, and the use of combination ratings between different types of core data provide for more detailed characterization of ground conditions. THE ST. PETER SANDSTONE The 45 m thick St. Peter is an unusually pure quartz sandstone. It underlies all the Twin Cities area, except where it has been eroded by the present day Mississippi River or by pre-glacial rivers. It forms conspicuous steep bluffs along the Mississippi River where the upper Platteville limestone formation protects it from erosion. Where the Platteville formation is missing, the sandstone slopes are often more gentle. Natural case hardening of the exposed sandstone bluffs often forms a resistant crust and reduces sloughing. This case-hardened surface is not representative of the sandstone back from the bluff.

Jan 1, 1987

By William R. Yernberg

The “China & East Asia Mineral and Energy Re-sources Symposium — CEAR 2000” was held Jan. 23-26, 2000 in Denver, CO. Conference sponsors included Resources and Technology Symposia of Colorado and the Asian Journal of Mining. The meeting was attended by representatives from China, Japan, Mongolia, Korea, eastern Russia (Siberia) and the United States. The US attendees consisted of interested parties from mining and energy companies, financial institutions, consultants and government agencies. In his opening statements, L. Maness, Jr., president of Resources and Technology Symposia of Colorado, said that the “goal of the conference was to make jobs and friendships and to introduce people to each other.” The conference provided an opportunity for Western mining interests, including mining companies and investors, to meet with government agencies from both sides of the Pacific.

Jan 1, 2000

By A. S. Macfarlane

Over the last few years, and especially the last few months, issues relating to Corporate Governance in industry in general, and the Minerals industry in particular, have become increasingly topical, as a result of a number of scandals and failures. The development of International and National Codes for the reporting of Mineral Resources and Reserves began some years ago, and has been followed by more stringent Listing Rules for the Securities Exchanges, as well as more standardised formats and protocols for financial reporting of assets and activities. More recently, some countries have adopted Codes for the Valuation of Mineral Properties, which have focussed on standardisation of valuation approaches to be adopted, and the qualifications of people deemed competent to sign off such valuations. This process has not been without criticism, the main criticism being the proliferation of local standards and regulations, which are often difficult to apply and regulate, or which are too prescriptive for multinational mining companies to deal with. In South Africa, these concerns have been recognised, while at the same time a need has been identified to establish a Code which could be applied to South Africa, and the African continent as a whole. Such a development would necessitate that the Code satisfies the needs of the continent, but in a global context. This global context has already been set by the activities of the International Organisation of Securities Commissions, the International Valuations Standards Committee and the International Accounting Standards Board. This paper explains the progress and process that has been established in South Africa for this purpose, and highlights the key issues which are open to public debate, so that the process is inclusive and transparent, whilst at the same time it is consistent with international time frames, and provides a deliverable product that meets the desired objectives.

Jan 1, 2004

By Richard A. Bideaux

With both unit costs per meter and average depth of drilling constantly increasing, there is a strong incentive to maximize the information acquired from drill holes, and then to make this information accessible to the geological staff. The larger the drilling project, the more advantageous computerization of data is over manual methods. The conversion to computer-readable form and the verification of large amounts of drill-hole data can be a substantial data processing task, but once accomplished, the benefits in increased accuracy and speed of interpretation will compensate for the time and effort spent in the work. For an exploration project progressing towards a preliminary feasibility study, about half of both the time and costs for all computer work of the entire feasibility study are devoted to drill-hole data base organization, and maintenance. Once drill-hole results are quantified and verified to be correct, they are immediately accessible and are not subject to further transcription or reinterpretation of errors. To obtain maximum benefits from computer utilization in this area, the drill-hole data base should be set up along with availability of the first data. For some companies, this may initially comprise a large number of purely speculative drill holes on a spacing of perhaps 1 or 2 km. Although few of these drill holes may encounter economic material, thought should be given, at this time, to the variables which will be logged when such material is found. In this way, it should be possible to set up a consistent format into which all future drill-hole information will readily be accommodated. This format may even be carried over into the data base requirements for an operating property.

Jan 1, 1979

By D. L. Watson

In spite of the deflationary state of the minerals business today, there will be opportunities for those who can fulfill future needs. Since there are abundant supplies of ores and fuels to keep prices down, at least in peacetime scenarios, future needs may be as much political and social as technical and economic. Engineers and economists will develop new and innovative ways to find, mine, process and pay for mineral deposits. Pressure from governments and non-governmental organizations and the public will combine with market forces to provide opportunities for highly competitive, risk-taking enterprises who can leverage the qualities of their orebodies and employees by being good neighbors and partners.

Jan 1, 2000

By Maurice Grieves

GC. Waterman Mr. Grieves' paper on "Shaft Sinking Today--A Boring Business Tomorrow" in the Dec. 1981 issue of MINING ENGINEERING is an excellent description of recent improvements in speed and costs of shaft sinking. However, shaft boring techniques are not a recent development. In 1935-36, the Idaho Maryland Co. (gold), Grass Valley, CA, bored the vertical 1.5-m-diam Idaho No. 2 ventilation and supply shaft to a depth of 346 m. The equipment was designed and perfected by Branner Newsome and was, I believe, described in "Transactions." Pickands Mather later bored a 1.8-m-diam shaft to a depth of about 305 m using Newsome's design. The Idaho No. 2 shaft cut through hard gabbro, diabase dikes, soft serpentine, very incompetent ankeritized serpentine and a strong fault zone. The completed shaft did not require timber support; the fault zone was cemented. Equipment consisted of a rotating 1.5-m or 3-m core barrel with a slotted bottom which cut a 76-mm kerf. The cutting agent was chilled steel shot introduced into the slot as needed. The driving mechanism and core barrel were lowered into the shaft, the former secured to the wall and the inshaft "engineer" operated the motors which controlled core barrel rpm and advance. After an advance of 1.5-3 m the equipment was lifted out of the shaft, a half(?) stick of powder cut off the drilled core, and it was hoisted to the surface with a cable attached to an eye bolt at the tope of the core. A "shift" consisted of three men: hoistman, equipment operator (down the shaft), and a surface laborer. Advance was variable as equipment and techniques were perfected. Near the end of the job advance was, as I remember, 1.5-3 m per shift. Costs were, as I recall, about $115/m. Up to 4 m cores were lifted out in one piece and swung to the dump by a stiff leg derrick. The Newsome equipment was relatively inexpensive to build and operate and his method should be (more than?) competetive with the methods described by Grieves. W.E. Hawes The author, in mentioning the South African developments of the cactus grab, ignores the parallel development of the Cryderman mucker in this hemisphere. Perhaps a slightly longer history of blind hold drilling would have been in order. Blind shaft boring got a major boost at the Nevada Test Site, as part of the nuclear weapons development, when it was essential to be able to quickly assess depth for weapons testing. One of the early civilian attempts to utilize this technology occurred when Kerr McGee drilled the shaft at the Section 19 Mine at Ambrosia Lake, NM. This twin masted drill rig belonged to a subsidiary of Kerr McGee, not Shaft Drillers. This was a difficult hole, due to bentonitic shales that decomposed. Later advances in drilling fluids eliminated this problem. The Conoco project referred to is not entirely correct, and needs minor amplification: The depth of the development (not pilot) shaft drilled was 684 m, at a diameter of 3.05 m, with a 2.16 m ID hydratatic casing being installed to a depth of 669 m. Conoco Inc., not Challenger, executed the drilling, however Conoco did use Challenger Drilling Company's Rig 14-S. Rig 14-S is unique in that it is specifically designed for shaft drilling, rather than being an oil field rig used for this service. All work was planned and directed by Conoco personnel. Deviation of the aforementioned shaft from vertical was 31 cm. Two smaller shafts (pilot shafts) were drilled with the same rig. These smaller ones were drilled 1.8 m in diameter, to depth of 665 m and cased with .91-m-diam casing, to depth of 650 m to be used as pilot holes for 5.5 m diameter shafts. The total elapsed time for all drilling, casing, cementing, and rig moves was 50 weeks. The constraints mentioned of vertical accuracy, torque, wall collapse, rig set up time, lining time etc., pumping out, etc., may not be as serious as the author implies. First, vertical accuracy: The record achieved by Conoco indicates that with reasonable care, good accuracy can be obtained, primarily by having a fair amount of weight in tension, rather than on the drill bit. Second, the amount of torque that can be applied to the drill stem has been greatly increased by the introduction of larger diameter drill stems, such as the new Hughes rig uses. Third, risk of collapse of shaft walls is minimal with the proper mud program. Basically, the walls are supported by the weight of the mud and it is not removed until some type of casing is installed and grouted in. Here in the real challenge of blind drilling shafts to devise a more economical method of lining bored shafts than using steel casing. The remaining issues were minor at Conoco, provided adequate planning and scheduling takes place. An excellent paper, "Shaft Drilling--Crownpoint Project" by Hassell H. Hunter, presented at the Fifth Uranium Symposium in Albuquerque in Sept. 1981 contains details of this project. A combination of blind boring, with enlargement by either mechanical means (boring machine, or tunneling type shield) or slabbing down, with muck removal through a larger bored shaft would seem to be the future trend in shaft development. The economics, especially for wet conditions, favor this concept over conventional sinking, as has been demonstrated at Kerr McGee --Churchrock, UNC--Churchrock and Conoco at Crownpoint.

Jan 3, 1983

By John L. Kaplin

The underground construction for the Phase I Combined Sewer Overflow(CSO) Project is on an impressive scale by any measure, appearing more so in a midsize city like Providence, RI. The Narragansett Bay Commission recently completed $350 mil-lion in construction to improve the water quality in Narragansett Bay. This project included a number of serious challenges, delays, and disputes. Looking back on this complex project completed within budget, it is hard to consider the work as anything other than a success. Along the way, this outcome did not always appear certain.

By M. D. Khattar

Problems discussed concern encountering of high temperatures [up to 66°C] and heavy flow of water [150 L.P.S] during the construction of the 10.15 MØH.R.T. for the 2500 MW Nathpa Jhakri Hydro Power Project in the Himalayas(India). Over a length of 2500 M progress of work got seriously affected resulting in excessive time for completion - two years [max. monthly progress achieved was 178 M [Heading]. Many innovative and simple steps were taken to complete the work in these inhospitable environs affecting working of both men and machines. Also it meant a review of the design of concrete lining. Other geological conditions affecting the progress are also described.

Jan 1, 1999

By Carl Pinches

Underground or surface mining is only the first stage in the ore mining process. Once the ore is mined, it is transported to the surface for further processing. Generally, this is done to extract the particular metal or other component of the ore that has commercial value in its purified form. In its raw state, there are typically between 4 and 7 g/t (0.12 and 0.2 oz/st) of valuable material from rock mined. Once on the surface, the ore is crushed and milled in order to obtain smaller rock particles and to expose the minerals that contain the desired metal or component. Mixing the milled ore with water, a process known as ?froth flotation,? can be employed. This technique consists of a series of tanks, or ?cells? through which the process liquid flows. To obtain the maximum recovery, the milling and flotation process will often be repeated a second time. An increase between 100 and 1,000 g/t (2.9 and 29 oz/st) of rock following this stage of the process is typical. Efficient recovery is key to maintaining a profitable mining operation. The measurement and control of the froth flotation process is vital.

Jan 1, 2010

By L. Franko, S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium circuits. In this study the performance of a continuous, laboratory wet-drum magnetic separator was evaluated with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration, and nonmagnetic materials. The results indicate that under certain conditions, the purity of the magnetic material increased after ultrasonic treatment.

Jan 1, 2001

By S. Saeb, C. Francke

Introduction Although mining in one form or another has existed for millennia, the use of numerical methods for mine design is a relatively recent development. The basic physics that control the behavior of rock or soil have been known for centuries, but it wasn’t until the last half of the twentieth century that analytical methods that could accurately predict the behavior of a large, irregular rock mass were developed. Before the advent of modern computers combined with differential and integral analytical methods, numerical methods available to mining engineers were limited to closed form solutions for simple excavation geometries. Today, mine-scale three-dimensional stress analyses can be performed on a relatively inexpensive personal computer. Many of the recent advances in rock mechanics modeling are the result of research funded as part of nuclear waste repositories around the world. The large scale exacting performance requirements of waste repositories are frequently very different from traditional rock mechanics projects. These facilities are designed and built under tighter control and scrutiny because of the potential hazards they present to the public. Therefore, a great deal of research towards advancing rock mechanics and numerical modeling resulted from these projects. Much of the repository research is applicable to commercial mines. The advances in modeling programs have been paralleled by advances in computer equipment. Today, a moderately equipped personal computer can handle most mine geomechanical modeling projects in a reasonable period of time. While the learning curve varies, an engineer with modeling experience can develop a medium sized model in a few days. The relatively low investment cost of geomechanical modeling today makes it accessible to most mining operations. The benefits of a solid geomechanical modeling program include reduced operating costs, improved safety, and reduced design costs.

Jan 1, 2007

By A. Davis, C. Webb, J. Sorensen

The abandoned Belle Eldridge Mine near Deadwood, South Dakota, is on land controlled by the U.S. Bureau of Land Management (BLM). The mine produced lead and zinc during the first half of the 1900s. Because of acidic drainage and elevated levels of metals in tailings and waste rock, the site was evaluated in 1998 and 1999. After evaluation, the mine was remediated during 1999-2001 by the BLM. Since remediation, values of pH in water samples have been nearly neutral and specific conductance values have been much lower than before remediation. The Grizzly Gulch forest fire of July, 2002, consumed much of the Belle Eldridge site and resulted in greater than normal erosion and sediment flushing during the months following the wildfire. Had the site not been remediated and the tailings emplaced within a capped repository, generation of acidity and off-site migration of heavy metals within sediments could have been severe at downstream locations.

Jan 1, 2007

By J. R. Shultz, R. J. Lambert

One of the present trends in the mining industry is the increased use of mining contractors. In the past, many project owners have utilized mining contractors for topsoil stripping or overburden removal, usually on a short-term or periodic basis. In recent years, mining contractors have not only removed the overburden, but mined the product as well. Why is this change occurring? A prevalent trend in the mining industry appears to be the outsourcing of non-core and non-strategic functions, allowing producers to focus more on areas of technical expertise where higher incremental value is added—that is the processing, refining, and marketing of the product. As capital allocation becomes more critical, this trend is likely to continue.

Jan 1, 2002

By R. Benito

This paper describes the development of a life of mine schedule (LOM) for one of the world?s largest known sedimentary Copper-Cobalt districts located in the Katanga Province, Democratic Republic of Congo (DRC). A particular feature of the Tenke Fungurume LOM schedule is the considerable number of pits/phases for scheduling, each competing to provide the best ore available to a capacity constrained process facility. This paper discusses the main scheduling objectives and constraints, data pre-processing as a scheduling aid, the mine scheduling approach, and results and conclusions.

Jan 1, 2011

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013

By L. Alan Weakly

Global warming is a political reality in the United States today. The actual impact of the continued utilization of fossil fuels is not known and is open to debate. However, the growing concern about the continued use of these fuels is problematic. There are technologies available to us today that would permit America to meet its future energy demand and not contribute to global warming. The inconvenient reality is that fossil fuels cannot completely be replaced with energy conservation and the use of wind, solar, hydroelectric, geothermal and nuclear energy. The connection between the greenhouse effect and global climate change was first identified by physicist John Tyndall in the 1860s. To prove the greenhouse hypothesis, Roger Revelle and his research team started measuring carbon dioxide concentrations in the earth?s atmosphere in the early 1960s (Becker, 2007). With the rising concern about global warming, scientists throughout the world have been obtaining surface and air temperature data. Scientists have also been comparing CO2 concentrations found in glaciers throughout the world with theorized annual temperatures. Data for both dates back 1,000 years. Armed with this data, many nations of the world and the United Nations Intergovernmental Panel on Climate Change (IPCC) have concluded that climate change is a reality. The IPCC also concluded that this climate change is the result of mankind?s consumption of fossil fuels and that catastrophic consequences will occur on a

Jan 1, 2008

By John Reilly

The author?s paper at RETC 2007, ?Alternative Contracting Methods? addressed strengths and weaknesses of DBB+DB and introduced Construction Manager/General Contractor (Portland model) and Alliancing (Australian model). Considerable interest in these was expressed by several public agencies at that Conference and at the presentation. The author is assisting the Washington State Department of Transportation (WSDOT) and the Toronto Waterfront Revitalization Corporation (TWRC) with possible implementation of Alliancing. WSDOT is evaluating ways to do this and is considering a delivery methodology, under existing Legislation, based on the CMGC Portland model with incentives and disincentives, moving towards Alliancing. This paper will build on the 2007 paper and update implementation considerations.

Jan 1, 2008