Search Documents

By M. Lohk, Y. -. R. Pastarus

Oil shale industry of Estonia provides a significant contribution to the country’s economy, but causes a large number of different problems. In spite of high economical parameters of the current underground mining (room-and-pillar) technology it is not effective. Backfill technology will be applicable in condition of Estonian oil shale mines. Nowadays attention has been focused on the use of combustion and mining by-products as filling materials. Use of ash and limestone in mining industry is treated as a part of mining technology, not as a waste disposal. Underground utilization of wastes reduces the volume and area required for surface disposal, environmental taxes. It improves the quality of mining works. The use of backfill technology has great impact on mining practice in Estonian oil shale industry.

Jan 1, 2011

By W. F. Riggs

1 Flotation Analogy To explain flotation in simpler terms the following analogy will be used. A factory (the flotation cell) manufactures a product (collector coated mineral). The product (collector coated mineral) is transported to market (the launder). A truck (the frother) is used to transport the product (collector coated mineral) to the market (the launder). The truck (the frother) transports the product over a road (the froth bed). The truck (the frother) and product (collector coated mineral) are supported by tires (the air). 2 Assumptions This operating philosophy assumes that the correct collector dosage is present along with the correct particle size distribution, pH conditions, etc. and that the minimum required frother dosage is correct. 3 Collector Addition The collector addition as used at a flotation plant is based on dosage rate as determined by the amount of mineral value entering the concentrator. Collector is normally added at two points in the concentrator: The primary flotation circuit and staged addition in the rougher scavenger circuit. Surveys have shown that the staged collector addition provides an increase in the kinetics and increases the recovery of the valued mineral in the rougher scavenger circuit. 4 Frother 4.1 Frother Dosage As explained in the above analogy, frother can be likened to the truck that transports the product (collector coated mineral) to market (the launder). Just as you would not use a truck rated at 15 tonnes to transport a 20 tonne load, you cannot expect to transport coarse minerals to the launder when there is insufficient frother present. Frother dosage must always be at, or above the minimum target. If less frother than the required minimum is used, then coarse mineral particles will not be supported and transported to launder where the mineral is recovered. To the naked eye the froth characteristics, even when insufficient frother is used, will appear to be correct. You cannot see the coarse particles that are not being recovered in the froth. (See Section 4.2 below for an explanation of why this occurs.)

Jan 1, 2006

By R. A. Jankowsi, S. K. Ruggieri

Airborne respirable dust levels on longwalls can be reduced if operators approach the dust control problem in a logical and fundamental manner. This can be accomplished through the proper application and continued use of effective dust control techniques. The Bureau of Mines is currently assessing the effectiveness of longwall dust control techniques in use today to provide mine operators with guidelines for selecting the most appropriate control technology. This paper presents a fundamental approach to the problem of shearer dust control. Three dust control techniques to be discussed are: deep cutting/increased pick penetration for reducing the amount of respirable dust generated; drum water sprays/improved water supply system to suppress the amount of airborne respirable dust; and improved external water spray system, the "shearer-clearer," to push the dust close to the face. The techniques have been evaluated in field trials and have been shown to be both practical and effective in applications to control shearer generated dust.

Jan 6, 1985

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By S. L. Lebo, J. D. Gargulak

Lignin, the second most abundant natural polymer and bi-product of the pulp and paper industry, has been commercially available in a number of forms since 1940. This growing industry is fueled by demand in traditional applications. Reagents that offer unique solutions in various mineral process applications are examples of advanced uses that also fuel growth. These applications include flotation reagents in fluorspar, bastnäsite and potash, as well as in the zinc pressure leach process. Due to the fact that no concerted effort has been made to find applications for modified lignosulfonates, it is quite possible that this natural material will find use in other benefication processes.

Jan 1, 2002

By C. R. Landis

The Wyoming bentonite industry finished 2005 with strong growth. For most of the markets, demand exceeded supply. The industry continues to be heartened by the strength of its longtime markets, oilfield and iron ore pelletizing markets. But overall, all of the major markets enjoyed good to excellent commercial conditions. Growth at the macroscale was fueled by the continued strong domestic economy, by the exchange rate of the U.S. dollar in global markets and by strong worldwide global demand. As result, two new greenfield operations are in the early stage of development in the Wyoming region for the first time in more than two decades.

Jan 1, 2006

By D. Brady

When deciding to deploy rescue teams underground the decision makers need to be able to determine that there won?t be an explosion whilst the rescue teams are underground. Previously general body concentrations in areas likely to be travelled were compared to explosive limits on a one off basis with no formal process looking at trends or other areas. A new approach is being adopted that takes into account the rate of change of gas concentrations with triggers set to enable a withdrawal of personnel prior to a possible explosion and influences such a barometric pressure changes. This paper explains the rationale behind the changes made and the advantages and implications of adopting such an approach.

Jan 1, 2012

In September 2003, a test was conducted to see if a115-mm- (4.5-in.-) diam Mocap Vari-Stem blasthole plug could improve the pattern of explosives using different top stemming material. The test took place at the J.S. Faulkroad and Sonsstone quarry in McCalisterville, PA. The test consisted of a production stone blast. Half of the holes were stemmed with standard crushed stone. Two-thirds of the remaining half were stemmed with Vari-Stem plugs and crushed stone. And the remaining one-third of the second 50 percent was stemmed with Vari-Stem plugs and only drill cuttings.

Jan 1, 2004

By R. Oler

The need for yieldable ground support, particularly in high stress or deep mining conditions, has grown in recent years. This paper highlights some of the current industry limitations and provides selection criteria for a new yielding ground support system, DSI?s Dynatork Bolt. This bolt distinguishes itself by withstanding 16 ? 30 kJ of energy deflecting loads anywhere from 7 ? 20 tons (depending on the energy). A summary of the laboratory test results and case studies will also be presented as a measure of the performance of this dynamic product.

Jan 1, 2012

By S. K. Kawatra, S. J. Ripke

Bentonite clay is used as a binder for iron ore concentrate pelletization. Bentonites are sensitive to cations such as calcium, magnesium, sodium, and potassium that are known to be dissolved in the moisture remaining in the iron ore concentrate. These cations affect the ability of bentonite to absorb water, as measured by the plate water absorbance (PWA) test. This paper addresses the relationships between plant water chemistry and pellet strength for a wide PWA range of bentonites. Experiments were conducted to determine the effect of concentrate moisture solute chemistry and bentonite PWA value on the wet knock and wet and dry compressive strengths of iron ore pellets. Experiments used seven different types of bentonite that had PWA values ranging from 564 to 1033. Flushing plant concentrate with distilled water to remove the dissolved cations resulted in increased pellet strengths, to a widely varying degree, for each bentonite tested; wet knock values increased an average of 92% and dry compressive strength increased an average of 46%. In addition, pellet strengths were not found to be directly related to the ability of bentonite to absorb distilled water, measured by the PWA test.

Jan 1, 2002

Diesel powered machines are doing some specific operations in the cyclic order required by the technical process. The dynamics of this process in certain conditions has an essential influence on environmental health conditions in the working area. The main purpose of this paper is to show, using computer simulation, how the movement (dynamic) of diesel vehicles effects environmental health standards and also how to determine the required air quantity for ventilation.

Jan 6, 1985

By K. Oraee

Mining Ventures are considered as high risk projects and therefore managing the risks is inevitable. Risk assessment is an important part of the complex process of risk management, hence applying appropriated and practical methods for ranking the risks associated with projects, can help to perform a better risk management. In this research the applicability of using Techniques for Order Preference by Similarity to Ideal Solution (TOPSIS) method for risk ranking in an underground mine, extracting by block caving method, was studied. Via this method, the risk associated with reserve estimation ranked as the first while in conventional method (P-I Matrix method) located in the sixteenth. Also there were significant differences in ranks of the other risks. Considering the more criteria, with different weights, in comparison with conventional methods, the results comprised from TOPSIS method are more reliable. By implementing this method risks are ranked better and more realistic and consequently then will be managed more efficient.

Jan 1, 2011

By D. Richers

When modeling predictive pit lake chemistry, groundwater chemistry is integrated with the affected portions of the wall rock and chemistry of the lake in a complex series of mixing. Fractions of the solutions impinge upon fresh, unaltered or fractured and oxidized zones of the wall containing sulfide materials and/or soluble metal/metalloid salts. Changing conditions over the short term (biannually) and long term (decades) can drive reactions allowing for dissolution or precipitation of acid rock drainage and metal leaching (ARD/ML) constituents. Local zonal variations can result in a portion of the pit releasing materials into solution; whereas other portions of the lake might favor the formation of colloids or precipitants. The proportions and character of groundwater can drive the chemistry of the pit lake provided sufficient buffering capacity is available to temper the generation of ARD in the system. For sulfide-rich systems, reduction of oxygen by rapid inundation and consumption by sulfides is key to reducing the ARD/ML. This paper presents several models of a sulfide-rich wall rock system using a range of groundwater chemistries to show these constraints.

Jan 1, 2012

By J. McMurray

Introduction Uranium was recovered from mining of collapse breccia pipe deposits in the Arizona Strip district in northwestern Arizona (Figure 1) intermittently between 1956 and 1990, with cumulative production having totaled 23.3 million pounds of U3O8 (8960 tU) at an average grade of 0.6% U3O8. Production was suspended in 1990 because of low uranium prices, but the recent resurgence in market price once again makes the breccia pipe deposits potentially attractive exploration and development targets. This paper describes: (1) formation of the pipe structures and their metallogenesis; (2) mining and milling of breccia ore; and (3) potential roadblocks to development of new breccia pipe mines. Breccia Pipe Formation Formation of the breccia pipes began in cave systems formed during development of karst topography in the Mississippian Redwall Limestone. The karst Redwall surface was eventually covered by up to 900 meters of shallow marine to continental sediments ranging in age from Pennsylvanian to Triassic. The pipes were formed by progressive upward stoping caused by groundwater ascending under hydraulic head along near-vertical faults, joints and fractures. The stoping process involved both chemical disaggregation and mechanical failure of roof and wall rock. Upward stoping of successively younger units allowed for upward propagation of a pipe and resulted in a chimney-like column of breccia between the steep walls of the pipe. Syndepositional thickening of sedimentary units of varying ages indicates that pipe formation began as early as early Pennsylvanian time and continued intermittently through Triassic time.

Jan 1, 2007

By J. C. Stankus, K. J. Ma, D. Faulkner

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding-type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high, causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concern for the U.S. Mine Safety and Health Administration (MSHA) and ground control engineers. During the last few years, Keystone Mining Services, LLC developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents an impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development and laboratory testing of a waterproof coated impact-resistant lagging panel and (3) impactresistant steel set design based on the law of conservation of energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Raja V. Ramani

As the new millennium approaches, it is appropriate to assess the progress that has been made in mine health and safety, a matter of concern to management, labor and government. One can hardly look at the major events of the last century — from the birth of the US Bureau of Mines through the enactment of the modern health and safety laws — without realizing that the march has been relentless toward eradication of health and safety threats in mining. The progress is spectacular in mine safety and significant in mine health. In looking at the future, it is safe to assume that societal demands will increase for improved health and safety conditions in the workplace. So will the demands for greater technological leaps. The standards will for measuring success and the expectations of progress in creating a safer and healthier mine environment will grow. The possibilities are enormous of meeting these exacting requirements in the 21st century.

Jan 1, 1999

In June, 1,334 underground construction and tunneling professionals gathered in Toronto, Ontario for the 2007 Rapid Excavation and Tunneling Conference (RETC). This biennial event, sponsored by SME, is one of the global underground construction industry?s major events. And this year?s RETC was the first one that included the new Underground Construction Association. [ ] (UCA) of SME. In addition, the conference?s exhibit attracted 125 equipment and service providers. The next Rapid Excavation and Tunneling Conference is set for June 14-17, 2009 at Caesar?s Palace, Las Vegas, NV.

Jan 1, 2007

By M. M. Botz

Cyanidation tailings which are disposed in a surface impoundment experience a loss of cyanide due to natural degradation, frequently reducing the cyanide concentration to very low levels. Quantifying cyanide losses in terms of pond geometry, local weather conditions and feed solution chemistry has been largely empirical though in many cases mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or an effluent limitation. To permit a more quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, WAD and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared against data collected for a North American tailings impoundment during 1998.

Jan 1, 1999

By Lynn B. Hales

There is a large economic opportunity associated with improving metallurgical performance in mineral processing plants that use process control. Thus, future control systems will be developed towards more sophisticated user friendly, computer-based systems that use powerful software analysis and control techniques. Auto-tuning, adaptive control and process models will gain expanded use because of their transparent availability to the system designer. Control of individual unit operations will be optimized and coordinated through expert systems that monitor economic conditions and management directives and direct operations accordingly. Plant areas, once considered cost centers, will be integrated into plant-wide control systems for economic control and optimization. This article looks at new control hardware, process sensors, control strategies and software development tools. It also looks at the economics driving the continued development of advanced process control systems. Process control systems routinely used in the mining industry were born when the microprocessor was invented. They have continued along an evolutionary path from vendor specific processing hardware and proprietary operating systems to computer industry standard "open architecture" systems. The many economic forces that drive the development and functionality of these process control systems will cause this evolutionary process to continue. Two of the broadest categories are the needs of the end users and the desire of the system manufacturers to distinguish their products from one another. More

Jan 1, 1994

ME?s Arizona Conference was held at the Hilton El Conquistador resort in Tucson on Dec. 2 and 3, 2007. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The 2007 meeting featured a keynote address, a distinguished lecturer and more than 25 technical papers that were presented in seven sessions. The sessions included environmental, geology, safety, metallurgy, mining, new projects and a special session on Mexico. Topics covered included mine closure, sustainable mining, exploration methods, health and safety issues, mining equipment and drilling. Much of the discussion at the conference concerned major new developments in the region?s copper mining industry. For example, Freeport-McMoRan?s new Safford Mine and BHP Billiton?s Pinto Valley restart were the topics of technical presentations. There was also much discussion among the attendees on the current and future price of copper, community relations, education issues and recruitment concerns. At the time of the conference, the price of copper hovered around $3.30/lb, up considerably from the 61 cents/lb in late 2001, when the industry was being challenged by world market conditions and a weakened domestic economy. Since then, strong demand from China helped push copper prices to record levels that at one time reached as high as $4/lb. The general consensus among the attendees is that the current price of around $3.30/lb will continue through 2008. Most attendees also expect increased corporate investments in the industry to continue. Copper mining in Arizona has been a major industry since the 1800s. In 2007, Arizona was the leading copper-producing state in the United States and produced more than $5 billion worth of copper. The copper mining industry in Arizona also produces byproduct gold, silver and molybdenum. Arizona is the second largest molybdenum producer in the United States.

Jan 1, 2008