Search Documents

By S. R. S. Sastri

By using the data of E.A. Hersam and F.C. Bond's equation for energy consumption in comminution, a method was developed to analyze the performance of industrial jaw crushers. The study showed that industrial jaw crushers are generally operated below capacity. The study also showed that industrial jaw crushers generally have sufficient installed power to operate at, full capacity. The method presented can be used to estimate the capacities and power requirements of jaw crushers.

Jan 1, 1995

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal properties and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Where gas plays a dominant role, the term outburst is often used; where stress concentration is primary, terms such as burst, bump or bounce may be used. Hargraves [1983] presents an often cited review of outburst phenomena with emphasis on Australian conditions. Beamish and Crosdale [1998] indicate outbursts have occurred for over a hundred years and present tabulations of outburst numbers in major coal basins throughout the world. A central consideration is the rate of depressurization that occurs in the course of mining. Outbursts are not limited to coal seams and adjacent strata; they also occur in salt and potash mines [Molinda et al 1988]. Stress concentration and gas pressure act in consort, so the combined action is important to understanding the mechanics of bursts or outbursts and to the development of measures to reduce the associated hazard. Gas flow is a complicated phenomenon associated with diffusion of gas from micro-pores and the flow of gas along cleats. Laboratory measurements indicate both are dependent on stress and pressure [Harpalani and Ouyang 1998]. Moreover, gas permeability in porous media is often many times water permeability [Klinkenberg 1941]. However, there is also evidence that gas and water permeability are similar at elevated stress and follow Darcy?s law [Dabous et al]. Gas flow is also of importance to mine ventilation. Price et al [1973] in cooperation with personnel of the former U.S. Bureau of Mines developed finite difference models to estimate methane emission in mines in the Pocahontas No. 3 and Pittsburg seams using a premining pressure of 4.69 MPa (680 psi) and Darcy's law implying laminar flow. However, the effects of stress were not taken into account. In this regard, mine measurements of permeability are usually based on Darcy?s law [Peide 1990]. Early models of gas flow with stress effects were one-dimensional in space and time (x,t) and were developed with the goal of estimating the gas pressure profile from the face into the seam as time passed [Schlanger and Paterson 1987, Zou and Yu, 1999]. A zone of high permeability adjacent to the mining face was recognized in these early models. Later models based on the popular finite element method allowed two spatial dimensions (x,y) and variation in time (t) and for coal seam heterogeneity [Tang et al, 2002]. Zhu et al [2007] formulated a set of nonlinear equations involving a complicated stress-pressure-permeability relationship for application to coal seam gas flow and concluded the coupling was important but failure of coal should also be considered. Wold et al [2008] used a hybrid finite difference - finite element model interleaved with a reservoir simulation model to study outbursts based on extensive mine and laboratory measurements. An important feature of the modeling was the use of spatially variable material properties and Monte Carlo simulation to obtain quantitative estimates of outburst conditions and probabilities. Connell [2009] used the same reservoir simulation model as Wold but used the popular finite difference code FLAC3D for hydro-mechanical responses to evaluate two permeability relationships, one depending on porosity and the other on stress, and concluded that permeability changes with gas production were more complex than computed by either permeability model. Gadde [2010] in an integrated laboratory and field study of coal pillar strength explored the effect of spatial variability and concluded that design based on average strength was acceptable in some circumstances, although gas pressure was not an issue. Liu et al [2011] also applied a FLAC code to analyze two-dimensional gas flow and deformation of layered but homogeneous strata in a Chinese coal mine using a strain-softening model and concluded that damage and gas pressure were important to strata safety relative to the case without gas.

Feb 27, 2013

By R. F. Balazik

By March 2001, shrinking global markets, reduced consumer spending and declines in domestic manufacturing and industrial output ended the longest economic expansion in US history and pushed the nation’s economy into its first recession in a decade. Aggravated by the terrorist attacks of Sept. 11, the recession led to large reductions in the domestic production of processed mineral materials. Some of the most significant production declines in the US metals industry were registered by aluminum, copper and steel producers. They faced strong foreign competition, higher energy costs and lower prices for their products. However, homebuilding and other domestic construction sectors — major users of nonmetallic mineral products such as cement, brick, glass and stone — remained strong enough to help raise the output of industrial mineral materials slightly above previous year levels. A strong US dollar continued to weaken the competitive stance of US metal and nonmetallic mineral materials companies alike against foreign producers in markets at home and abroad.

Jan 1, 2002

By V. Gall, J. Rudolf

The Virginia Department of Rail and Public Transportation and the Metropolitan Washington Airports Authority are undertaking the extension of Washington Metropolitan Area Transit Authority’s Metrorail service to Washington Dulles International Airport and beyond to Route 772 in Loudoun County, Virginia. The roughly 37 kilometers long, double track alignment involves two 700 meters long single track, soft ground NATM tunnels at Tysons Corner, two 3.3 kilometers long single track rock TBM tunnels at Dulles Airport and one 25-meter deep station at the airport to be constructed by NATM in sedimentary rock. The design-build project is being implemented in a Public-Private-Partnership. A joint venture of Bechtel and Washington Group International has concluded the preliminary engineering and construction is scheduled to start in late 2007.

Jan 1, 2007

By S. G. Mougiakakou

A computerized system (SCAPEVIEWER) based on landscape indices and artificial intelligence techniques is proposed in order to classify landscape images into various categories according to the quality of the pictured scenery. Photographs (totally 108) from various landscapes have been clustered, from seven experts in accordance to the mean estimation of landscape quality, into distinctive (C1), typical or common (C2), and indistinctive (C3). For each of the landscape photographs, ten (10) environmental and operational indices have been selected and determined, corresponding to visibility (V), naturalness (N), relief (R), flora quantity (FC), flora quality (F), water (W), skyline (SL), visual entities (G), season (S), and viewer position (P). These landscape indices are fed to a classifier. The classifier is a feed forward Neural Network (NN) trained by a novel hybrid method combining genetic algorithms and the back-propagation algorithm with adaptive learning rate and momentum. A total classification rate of 93.5% has been achieved, using only 8 input neurons. The discarded input neurons correspond to the indices S, and P. The pilot system SCAPEVIEVER has shown the feasibility of landscape photograph classification into three categories (C1, C2, and C3) according to the landscape quality, selecting simultaneously the most robust indices, by means of a computerized system combining the knowledge of an expert with a NN based classifier.

Jan 1, 2003

By David Caiden, Geoffrey Fosbrook, Jaidev Sankar, Donald Phillips, Jon Hurt, Anil Parikh

This paper will cover the progress being made on Phase 1 of New York’s Second Avenue Subway line. It will include a description of construction progress on the first contract to be let, which consists of a 248 m (815 ft) long launch box, 3.9 km(2.4 miles) of TBM tunnels and a tunnel sump; the packaging strategy for the remaining work; and the progress through Final Design of the remaining packages, including the two large span rock cavern stations.

Jan 1, 2007

By L. Kulik, J. den Drijver

Rhenish lignite will continue to play an indispensible role in the energy mix of the German Federal Republic for a long time to come. The use of lignite for electricity generation, upgrading and, if necessary, as a raw material is geared to the long term. The holistic management of opencast mines underpinned by approval law in the long term and a stronger focus on man, the environment and nature contribute to the acceptance of the mines by the local population. The same is true of state-of-the-art lignite uses: as regards their operational flexibility, lignite-fired power plants are ideal partners for the expansion of renewables. It is along these lines that RWE is continuing its power plant renewal programme as planned. With a view to that which will be conceivable the day after tomorrow, RWE is researching future technologies today in order to meet objectives such as security of supply, profitability and environmental compatibility to the same extent in the long term. Another important contribution to acceptance is public transparency and communications as means to support approval procedures and the implementation of measures in all areas related to lignite mining and utilization.

Jan 1, 2011

By J. Warmbrodt, D. Apel, D. Nutakor, L. Grayson, M. Hilgers

MinerSIM is an augmented reality system with integrated hypermedia that is suitable for training underground miners in the basics of using a jackleg drill to install rock bolts. While statistical evidence shows that rock bolting with such a drill has an inherent level of risk, it is conjectured that this can be mediated with adequate safety training outside of the actual mine environment using a variety of educational media including interactive three-dimensional images, games, animations, and videos to describe the mechanics of rock bolting and its principles. Ultimately, trainees will install rock bolts in an immersive environment mixed with real and virtual images generated via a gaming graphics engine. This paper will discuss considerations, implementation issues, and evaluation methodologies of the MinerSIM system.

Jan 1, 2007

By C. A. Johnson, K. F. Unrug

The identification of the major subsidence areas in the Eastern Kentucky Coal Field has been made to distinguish the subsidence phenomena on the basis of geographical location. Further, this identification process is based upon selected critical geological, topographical, and mining features in the coal fields. The proposed identification of the regions is derived from a comparison of the subsidence potential in a particular area. The most likely severe subsidence areas are compared to those with the probable low subsidence severity. The combination of certain geological and mining parameters involved allows for the derivation of a classification of the subsidence potential.

Jan 1, 1986

By James Dunn

“The strongest argument of the detractor (of mining)is that the fields are devastated by mining operations ...They argue that the woods and groves are cut down, for there is need of an endless amount of wood for timbers, machines and the smelting of metals. And when the woods and groves are felled, then are exterminated the beasts and birds, very many of which furnish a pleasant and agreeable food for man. Further, when the ores are washed, the water which has been used poisons the brooks and streams, and either destroys the fish or drives them away.” Georgius Agricola, 1556, De Re Metallica, translated by Hoover, 1950. Technical problems associated with the cleanup of historic mines are not new. Nor are they unique to the mining industry or the governmental agencies addressing them. Both face the same issues and challenges of defining the problems, evaluating remediation options and finding the most economic and effective solutions.

Jan 1, 1999

By R. K. Jade

Although several studies in combining and bifurcating flows in two-way junctions and splits are reported, deviations persist in the estimated shock loss coefficients (SLCs). Due to their complex nature, more work has to be done to be able to correctly predict flow losses at these locations. In two-way splits, the flow at bifurcation is known to be characterized mainly by two recirculating zones in the downstream branches, whereas, in a junction one recirculating zone is observed immediately downstream of the main branch. The relative flow rate in the branches (quantity ratios) is treated as the only parameter defining the losses at these locations. However, the effect of wall roughness, if any, on SLCs becomes important for mine ventilation. This paper presents the critical determinants of shock losses at splits and junctions at varying quantity ratios. The flow at 90º split and junction was examined both experimentally and numerically for Reynolds number in the range of 1.0×104 to 1.6×105. With a well designed laboratory setup, using precision instruments, velocity and pressure measurements were carried out, by using two scales of wall roughness. 3D numerical simulations for these experiments were conducted by using ANSYS CFX modeling tool. CFD simulations yielded results that are reasonably close to experiments, providing high degree of satisfaction in numerically predicting losses across the splits and junctions. However, comparisons of these numerical simulation results with existing literature standards showed significant under-estimation of shock losses by the standard literature by as much as 50%. A clear rise in the magnitude of shock losses was noted in both the approaches, with increased wall roughness. Based on the current studies, predictor equations incorporating quantity ratios are developed for accurate estimation of shock losses. Further investigations on roughness are needed, before one is able to incorporate wall roughness into the prediction of SLC.

Jan 1, 2009

If one can embrace the medical analogue, much of the mining industry currently suffers from a massive bacterial infection. When pyrite-bearing or sulfide-bearing rock formations, tailings, or mine wastes are infected by Acidithiobacillus ferro-oxidans, the likelihood of forming acid rock drainage (ARD) is almost guaranteed. The ?pharmacy? of antibiotics available is extensive, ranging from solid alkaline amendments like limestone to liquid ?medicines? such as sodium lauryl sulfate, sodium thiocyanate, waste milk, and bipolar lipids. Unfortunately, the ?geo-medical? teams of geochemists, microbiologists, engineers, and mine managers lack the tools to surgically apply these active ingredients where they are needed most with a minimum of waste. Distribution of fine grained limestone on the surface of an acidic mine waste dump is analogous to applying a bandage soaked in antacid to treat an upset stomach. The implementation of up-to-date best management practices has not healed the patient; an equivalent combination of hypodermic needle, cyber knife, and arthroscopic probe is clearly needed. Using an engineered, flow-able or pumpable foam or pHoam? as the medicinally analogous ?dextrose delivery solution? for solid and/or liquid ?geo-antibiotics?, the authors have combined off-the-shelf technologies that have been previously applied in solving geotechnical problems in the mining industry. A patent for the innovative process is pending. This paper discusses method concepts and the advantages it could provide over conventional BMPs.

Jan 1, 2012

By T. Hudaverdi

Control of the particle size distribution of a muckpile after blasting is always an important subject for mining industry. Blasting has a significant impact on downstream processes such as loading, crushing and grinding. Improvement of blasting results provides increase in loader and excavator productivity due to increased diggability capacity, and increased bucket and truck fill factors. Suitable and uniform particle size distribution results increase in crusher and mill throughput and decrease in energy consumption in size reduction process. Digital image analysis technique has been used for many years in mining industry in order to determine blast fragmentation. The images of muckpile surface can be used to determine the mean fragment size (x50). The source of digital images can also be haul truck, leach pile, waste dump, stockpile, and conveyor belt. The screening that is conventional method to measure blast fragmentation is time consuming and expensive. Digital image analysis is a cost effective and faster method (1).

Jan 1, 2012

By Helmut Westermayr, Michael Tergl

DESCRIPTION OF PROJECT Geographic Setting The Kops II plant is a pumped storage scheme of the hydroelectric power producer ‘Vorarlberger Illwerke AG’ which is currently under construction in the Austrian Province of Vorarlberg. The plant is located at the end of the Montafon valley and will be fed with water coming from the Silvretta mountain range (Figure 1) Description of Plant The Kops II plant shall be operated as a pumped storage plant with three highly flexible and quickly controllable power generating units. Each unit shall have a capacity of 150 MW and shall be equipped for both turbine operation and pump operation. The Kops II plant uses the existing Kops Lake as upper storage reservoir and the existing Rifa balancing reservoir as lower storage reservoir. All major plant components of the Kops II scheme are located below ground. Total investment costs areapprox. 360 million Euro. Construction Lots The construction works for the Kops II plant, which were subdivided into three lots, were launched in September 2004. It is planned that the first power generating unit shall go on line in the year 2007. The completion of the overall project and the operation start-up of the second and third unit are envisaged for the year 2008. Lot 1—Pressure Tunnel. The 5.5-km-long pressure tunnel forms the connection between the Kops Lake and the beginning of the pressure shaft. The tunnel was excavated by the use of a double-shield TBM. Lot 2—Pressure Shaft and Surge Chamber. The approx. 1.1-km-long pressure shaft was excavated by TBM, advancing from bottom to top. Featuring an inclination of80%, the pressure shaft overcomes a difference in height of approx. 700 m. Lot 3—Power House Cavern and Tailrace Structure. The power house cavern, which is being built approx. 150 m inside the mountain, forms the core of this plant. The power house is designed to accommodate three power generating units, and the transformer cavern is forseen to accommodate three transformer units. The tailrace structure serves the purpose of conveying the water to the lower storage reservoir during turbine operation and as water intake during pump operation (Figure 2).

Jan 1, 2007

By R. Hardy

LaModel is a boundary-element program capable of calculating the displacements and stresses in thin bedded deposits such as coal, salt, or potash. Throughout its history, it has continually been upgraded in order to expand analysis detail and stay current with the latest advances in computer technology. The most recent enhancements include: an increased grid size capability, a significant increase in the speed of the automatic grid generation using an AutoCAD visual interface, implementation of subsidence-based horizontal strain calculations for multiple-seam situations, and pillar safety factor calculations. To demonstrate these new features, a multiple-seam case study of a longwall panel undermining an active set of main entries is presented.

Jan 1, 2006

By Martin Herrenknecht

After the successful breakthrough at the end of 2006 of both TBMs into the multifunctional site Faido (MFS), in the middle of 2007 the two tunnel boring machines resumed the 12 km long section between Faido and Sedrun. In the roughly a 10 month interval both approximately 465 m long tunnel boring machines were partly dismantled, pushed through the 2.5 km long MFS, rebuilt for the new larger diameter of 9.5 m and reassembled to be ready for operation. In the rebuilding phase, improvements were made to the equipment, especially as a result of experience gained from the previous 14 km long drive in the section Bodio and taking into account the latest information regarding the upcoming 14 km section Faido. Both TBM drives are currently in the rock formations of the Lucomagno gneiss, which stretch over a section of 3.5 km from the MFS Faido to the predicted Piora Syncline. This section is divided into two fold axes of the Chièra Synform, where the Lucomagno gneiss pass from a sub-horizontal into vertical bedding. The drives, with current rock overburdens exceeding 1,500 m and, as known from the excavation phase of the MFS, in part highly disturbed rock formations, are characterized by the locally intense rock squeezing conditions with large convergences in the vicinity of the driving TBM as well as backwards due to the interaction of the two drives. High expenditure for the support measures, reduced driving performances together with extensive extra work associated with deadlines and increased costs are the result. In the paper the previous experience with the TBM drives in the section Faido and the challenges still awaiting us are presented and discussed.

By M. A. Oskouei

Draglines are the main energy consumers in strip mines. Given the growing cost of energy and environmental concerns, it is important to properly understand dragline energy efficiency. The goal of current research at Missouri University of Science & Technology is to account for operator practice and operating conditions in modeling dragline energy efficiency. This paper presents preliminary correlation analysis and a framework for stochastic modeling of dragline energy efficiency. Thirteen operating parameters (including cycle times, payload, swing angle, and height of dump pile), operator working schedules, operating conditions, and drag, hoist, and swing energies were monitored for an 85 yd3 dragline. Operator effects were examined by two-sample t-tests. The relation between the parameters and energy consumption were assessed by correlation analysis and a stochastic modeling framework has been proposed for dragline energy efficiency. The results show that operator effects are significant (p< 0.05) and energy efficiency is correlated with operating parameters. The completed model will help the coal mines better predict energy consumption, with uncertainty, for different operating conditions.

Feb 27, 2013

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009

By A. Broussaud, J. D. McKay

Benefits analysis of adaptive Expert control systems operating at plants in Africa and the United States are presented. Proper statistical tools and techniques are discussed. Technical and practical pitfalls of strategy comparison are also presented and illustrated with from published data. Advantages and disadvantages of a “Pay for Performance” approach to a project are reviewed.

Jan 1, 2001

By Thomas P. Kwiatkowski, Joginder S. Bhore, Christopher D. Orlandi, Jose Velez

Three case histories of successful TBM tunneling for New York City Water Tunnel No. 3 are presented. The tunnels, costing about one billion dollars total, are the 5-milelong, 18&apos;-11" OD Brooklyn Tunnel; the 5-mile long, 23&apos;-2" OD Queens Tunnel, and the9-mile long, 12&apos;-4" OD Manhattan Tunnel. The three tunnels are the first major tunnels constructed in New York City rock utilizing the TBM method of construction. This paper describes and compares the three tunnel projects in terms of geology, construction methods, TBM’s, rock and groundwater behavior, rates of advance and other performance data, and challenges and solutions encountered during the projects.

Jan 1, 2007