Search Documents

By F. R. Deist, R. P. Plewman

Discussion: A. Hazell (Associate Member) and T. J. Kotze (Graduate Member): The authors must be congratulated on the development of a versatile computer programme for determining the stresses and displacements resulting from mining operations. As a design tool it will no doubt take its rightful place together with the analogue computer. Union Corporation made use of this digital computer programme whilst still in its development stage to determine the stress distributions which were causing the unexpected failure of the Marievale sub-incline shaft. Two features arising from this investigation may be of interest to members, namely: A. The solution to the problem of stabilizing a rectangular inclined shaft, which turned out to be contrary to accepted mining practice, and B. A comparison between the results obtained with the pure digital system and the analogue computer. A. The shaft is nine ft high and 20 ft wide, dipping at 9° to the horizontal and crossing the bedding planes. Fig. 1 is a plan and Fig. 2 is a section of the sub-incline shaft pillar area showing the relative positions of the shaft and reef as well as their respective dips. The deepest point in the shaft is 3 300 ft below surface and the requirement of a stress free ground surface may not be satisfied. It also means that the original gravitational stresses are low. A 900 ft wide pillar was left to protect the bottom section of the shaft, the top section being understoped years ago. Extraction of the pillar was started at the beginning of last year, mining operations being carried out in the accepted manner, starting beneath the shaft and mining outwards. The approach did, however, turn out to be the wrong one, because failure of the shaft was noticed soon afterwards. Even small movements were serious in this case due to the low clearance between the skips and the shaft supports. During October, 1968, failure between benchmarks 8 and 10 (see Fig. 1) became so excessive that hoisting speeds had to be reduced. Failure continued to occur and, by the end of March, 1969, failure had propagated up the shaft as far as benchmark 7, and down as far as benchmark 12. As this shaft had a tight hoisting schedule it was imperative that a quick solution be found to arrest the failure.

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009

By M. M. Hajdasinski

The internal rate of return (IRR) is one of the most popular project evaluation criteria in the mineral industry, as well as in other industrial sectors. Analysis of its assumptions reveals, however, that this criterion does not function in the way it is supposed to. The search for a new criterion that would reflect the true rate of return (TRR) of an investment project or the true borrowing rate (TBR) of a borrowing project has led to the development of several approaches, yielding, for the same project, generally different values of the interest rate in question. Two of those approaches have been selected as the most representative and practical. Each has been presented in two variants, and subsequently analysed. As a result, it is shown that the various approaches to the TRR/TBR are all consistent with the net present value (NPV) criterion, and that each can serve as an independent project evaluation instrument, provided its assumptions can be regarded in a given situation as realistic enough.

Jan 1, 1987

By R. V. Ramani, R. Stefanko

"The favorable mining conditions in the United States of America that resulted in the development of the highly productive room and pillar systems are largely disappearing. Increasing mechanization, poorer natural conditions, and greater concern for health, safety and environment gave impetus to the enactment of the Federal Coal Mine Health and Safety Act of 1969. These regulations prescribe more stringent requirements in face ventilation and mine air distribution, necessitating significant changes in existing ventilation systems. Stringent mandatory standards were applied to respirable dust control for the first time, and simultaneous control of both gas and dust has affected the face as well as primary distribution, most notably on haulage entries.The size and complexity of the present-day mining operations, and the need to evaluate various system changes in a limited time, call for scientific methods in mine planning. In this paper, the authors trace the previous applications of computers to mine ventilation planning and discuss the results of their work in applying a ventilation simulator developed at Penn State. The paper includes an analysis of current trends and suggestions for future research and development."

Jan 1, 2014

By J. -M. Chautru

A geostatistical simulation of a typical mining site for polymetallic nodules in the North Pacific Ocean is presented. This is the first stage in the design of an industrial mining system. Two variables which have a major effect on the orebody's economic potential are considered, namely: the maximum slope of the ground inside a mining block of 50 x 100 m; and the average quantity of nodules on the same support. Two geostatistical problems have emerged in this study. The first is due to the lack of a change of support model for the maximum of a variable. A provisional solution, considering an experimentally accessible 'equivalent' support, is proposed. The second is due to a non-linear link between the two variables. To be able to take this into account in the simulation, we propose a new method based on the decomposition: X = E(X/Y) + Residue (X). Satisfactory results were obtained with this approach.

Jan 1, 1987

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 µm. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By J. C. D. Gush

Paper written on project work carried out in partial fulfilment of Laboratory-scale testwork was undertaken to recover oxidic copper-cobalt minerals by froth flotation, which requires maintaining a certain sulphide level in the pulp. To improve control of the sulphide concentration, an electronic closed-loop system was designed that responds to the potential output of an ion-selective electrode. The PID control was improved by adding a pre-emptive control and a self-calibration feature; a data logging facility is also included. An inexpensive valve design was incorporated using locally available parts. The operating results of this control design are presented.

Jan 1, 2005

By T. Szendrei, S. Tose

The fracturing and movement of rock that occurs in the vicinity of a stemmed borehole charge in open pit mining operations are described by examining the effects of the emitted stress waves – shock and elastic – and the expansion of high-pressure detonation product gases. Three principal modes of momentum transfer to fractured rock are identified, all linked to gas expansion work. This work can be delivered radially (burden), axially (stemming), and in the collar zone (cratering). Flyrock is generated under unusual combinations of blast parameters and rock properties. Although infrequent and seldom predictable, the generation of flyrock can nonetheless be interpreted and modelled in terms of the principal mechanisms of rock projection described in this study. The physical processes underlying these principal mechanisms are identified and will permit the development of predictive models for flyrock velocities.

Dec 13, 2023

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries to remove iron and sulphur from the molten matte phase. This technology has not changed significantly since its inception in the early 20th century. The typical converting operation involves lateral purging of air/oxygen-enriched air into molten matte through a bank of tuyeres. This blowing operation occurs at low air pressure from the blowers, and the induced bubbling regime is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks include recurrent tuyere blockage, inevitable tuyere punching operation to clear airways, and low oxygen efficiency as a result of substantial air losses due to leakages.Investigations in the 1980s demonstrated1 that jetting into Cu and Ni converters could reduce or eliminate some of the process difficulties. In spite of these findings, very little progress has been made in the application of these concepts for converting of non-ferrous melts on a commercial scale.As part of its operational improvement and energy reduction initiative, Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to full-scale industrial evaluation, a numerical assessment was conducted to ascertain the feasibility of implementing sonic injection on Lonmin converters. The work included flow characterization at high injection pressures achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid (VOF) and realizable k- e turbulence models to account for the multiphase and turbulence nature of the flow, respectively. These models were applied using the commercial CFD numerical code FLUENT.This paper discusses the key findings regard ing understanding of gas plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a fullscale implementation of sonic injection in the smelter."

Jan 1, 2014

Members are advised that the Council has decided to change the format of the Journal from the present size to the standard international A4 size with effect from August, 1969. By making this change we will be conforming to more general practice today in regard to publications and this should effect certain economies and facilitate selling of advertising space. It has been arranged that in future the publication of the Journal, including advertisement sales, will be handled by Kelvin Publications (Pty.) Ltd. who are already doing this work satisfactorily for the Mechanical and Electrical Institutes. While making these changes, the opportunity is taken of redesigning the outer cover of the Journal to incorporate the new coat of arms. The Council trusts that these changes will meet with the approval of members.

By M. H. Moys

Accurate models of mill power are becoming more necessary as the design, operational, and control requirements for grinding mills become more stringent. Models of mill power are reviewed briefly, and a new semi-phenomenological model is derived. The conventional torque-arm model for mill power is combined with a model of the tendency of the load in a mill to centrifuge at high speeds, to describe mill power that can be related to several design variables (such as mil geometry, mill speed, and liner design) and control variables (such as load volume, slurry rheology, and mill speed in the case of variable-speed milling). The semiphenomenological nature of the model allows rational conclusions to be reached concerning the effect of various aspects of mill-load behaviour on mill power. The model is shown to be capable of describing reality with much greater accuracy than is achieved by empirical models such as the Bond model.

Jan 1, 1993

By J. W. Drelich, H. Zeng, L. Xie, X. Cui, Z. Gao, M. Tian, Y. Hu, W. Hu, W. Sun

Flotation is a mineral separation technology that uses the surface hydrophobic difference of valuable minerals and their associated gangue minerals to separate them. The flotation collector adsorbs on the valuable mineral surface to improve its hydrophobicity, and metal ions are usually used as activators to enhance the collector adsorption. Different mineral surfaces show different charging properties and adsorption behaviours with the collector or metal ions. Moreover, the order of adding metal ions and the collector also show significant and different flotation performance for the same mineral. The adsorption or flotation behaviour or both are governed by mineral surface chemistry, such as surface charging and reactivity. In our recent studies, force measurement using atomic force microscopy (AFM) was employed to study the surface charging and adsorption mechanism of metal ions and collectors. By preparing collector-functionalised AFM tips, AFM can directly measure the adsorption strength of the collector on the mineral surface to determine the anisotropy of mineral surface reactivity. The preparation of collector-functionalised AFM tips provides the foundation for further study of the activation role of metal ion in the collector adsorption. The application of AFM for force measurement in the surface chemistry of mineral flotation can provide important information on developing flotation reagents and lays the foundation for the specific regulation of mineral surface characteristics. Keywords: Scheelite; flotation; surface chemistry; AFM force measurement

Jan 1, 2020

Jigging is a process of particle stratification in which the particle rearrangement results from an alternate expansion and compaction of a bed of particles by a pulsating fluid flow. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. The particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen and helped and influenced by the feed material that is introduced at one end. Following the particle stratification, the particle bed is physically ?cut? at a desired horizontal particle density plane to separate the desired product from the less dense gangue material. The issue of correct pulse characteristics (shape, amplitude and frequency) for the optimal metallurgical stratification of air pulsating jigs has been the subject of much discussion over the years. The accuracy of the dissymmetric stratification depends on the control parameters and the mechanical condition of specific equipment used. This paper will touch on some of the control and mechanical parameters affecting the separation efficiency.

Jan 1, 2010

A modified germanium recovery process in conventional zinc metallurgy, based on the understanding that ferric hydroxide has strong ability to coprecipitate germanium element, was presented. The relaxed lab-scale experiments were conducted to evaluate its technological feasibility. The experimental results obtained show the new process has great competitive advantage over the conventional one.

Jan 1, 2008

By C. P. Smyth

Large volumes of quantitative geochemical data, presenting a formidable interpretation task to geologists, are generated in the course of exploration drilling for new ore deposits. The incorporation of geological expertise into computer programs developed for the interpretation of this data would improve the speed and accuracy with which it is interpreted. A detailed analysis of the geochemical log interpretation problem, together with a survey of relevant research in Artificial Intelligence and petroleum well- logging techniques, confirms, that artificial intelligence, particularly as developed in the fields of expert systems and pattern recognition, provides techniques for implementing such data interpretation programs. In addition, it provides data analysis techniques significantly more powerful than those currently applied to geochemical data, and very appropriate to the hypothesise and test&apos; character of mineral exploration problem-solving. The conversion of raw borehole log data to meaningful higher level geochemical entities, in terms of which geological reasoning may take place, is a critical step in applying these techniques to log data analysis. A method of achieving this conversion as an exercise in signal-to-symbol transformation is presented.1

Jan 1, 1987

By F. Lanaro, K. Röshoff, R. Christiansson, L. Jing

This paper presents the results of a project for developing a methodology for empirically determining some of the mechanical properties of the rock mass at the Äspö Hard Rock Laboratory, Southern Sweden. Using the equations available in the literature, the deformation modulus, friction angle, cohesion and unconfined compressive strength of the rock mass were estimated. A comparison of the results using different classification methods (Q, RMR, GSI, RMi, Ramamurthy’s) was made to estimate the range of variations in the mechanical properties with the considerations of: i) the quality/quantity of the geological data; ii) the technique for partitioning of the rock mass into homogeneous domains; iii) the sensitivity and subjectivity of the empirical methods; and iv) the need for validating the empirical methods against a test case. Cet article présente les résultats d’un projet visant à établir une méthodologie, pour déterminer, de façon empirique, les propriétés mécaniques de la masse rocheuse. En utilisant les corrélations disponibles dans la littérature, quelques-unes des propriétés de la masse rocheuse ont pu être déterminées (module de déformation, angle de friction, cohésion, force de compression illimitée). Une comparaison des résultats obtenus par différentes méthodes (Q, RMR, GSI, RMi, de Ramamurthy) a permis d’établir une échelle de variations des propriétés mécaniques et de formuler une série de recommandations concernant : i) la qualité/quantité des données géologiques ; ii) la technique de partition de la masse rocheuse dans des domaines homogènes ; iii) la sensibilité et la subjectivité des méthodes empiriques ; iv) la nécessité de valider les méthodes empiriques à l’aide de nouvelles études de cas. Dieses Paper präsentiert die Ergebnisse eines Projekts mit dem Ziel, eine Methodik für die empirische Festhellung von mechanischen Eigenschaften im Gesteinmassiv zu etablieren. Durch Verwendung der in der Literatur zugänglichen Korrelationen, wurden einige Eigenschaften des Gesteinmassivs festgestellt (Entstellungsmodul, Reibungswinkel, Kohäsion, unbeschränkte Kompressionsstärke). Ein Vergleich der Ergebnisse unterschiedlicher Methoden (Q, RMR, GSI, RMi, Ramamurthy’s) wurde durchgeführt und dies erlaubte die Feststellung der Variationsskala von den mechanischen Eigenschaften, sowie eine Reihe Empfehlungen für: i) Qualität/Quantität der geologischen Dateien; ii) die Technik für Teilung des Gesteinmassivs in homogene Domäne; iii)die Empfindlichkeit und Subjektivität der empirischen Methoden; iv) das Bedarf die empirische Methoden gegen neue Fallgeschichten zu validieren.

Jan 1, 2003

By S. K. Lahiri, K. C. Ghanta

Design of industrial slurry pipelines is usually performed by applying semi-empirical procedures, requiring a significant experimental study for each project. The mechanisms of suspension flow are not yet completely understood and existing predictive models cover only some aspects of uniform or closely graded particle slurry flows. This paper presents a computational technique for prediction of the velocity and concentration profile in slurry pipelines based on computational fluid dynamics. This model gives numerical solutions for the concentration and velocity distributions in the pipeline cross-section. The model prediction and experimental concentration and velocity profiles were found to be in good agreement. Keywords: pressure drop; concentration profile; particle diffusivity; slurry flow.

Jan 1, 2007

By C. Norden

The purpose of this article is to show how a representative overall equipment effectiveness (OEE) measurement can be calculated for an underground coal mining bord and pillar batch process. The calculation method, the typical losses (which include planned and unplanned availability losses, coal quality losses, and process rate losses) and the underlying logic are presented and discussed. It is argued that the current traditional underground bord and pillar mining process can currently provide a maximum theoretical OEE of only 49 per cent, while a realistic benchmark target should be in the order of 37 per cent, which relates to an average of 2400 t per shift or 1.2 Mt/a. In addition, it is argued that the current bord and pillar process is the current bottleneck to further improvement past the 2400 t per shift benchmark, and that fundamental process changes will be required to eliminate this bottleneck.

Jan 1, 2012

By C. E. Dohm

The paper serves to show the importance of both a geological model and geostatistical model that support one another in mineral resource evaluation. It highlights the advantage of reference models for the geometry, the geological, statistical and geostatistical models of various orebody types and introduces a method for quantifying the combined uncertainty in these models. The example presented reveals how the above levels of information can be applied to add value to a resource evaluation process. It is a generic example in that it is the technique of combining uncertainty in the geological model (boundaries) as well as the grade model to assess the overall risk in the estimation of the resource. Data from the coal industry is used to illustrate the techniques. The geological uncertainty is considered via categorical simulations and these are combined with simulations of the variables (grades, thickness,) being estimated in the resource. The simulation techniques used are based on the application of GSLIB software1and a general discussion of the two simulation processes is included. In conclusion the paper demonstrates how the results of two types of conditional sequential simulation can be combined to produce confidence limits that take both uncertainties into consideration. This technique does not replace the resource estimation; it serves as an additional tool to quantify confidence in the resource evaluation model. The topics considered in this contribution are in terms of continuous improvement of mineral resource evaluation.

Jan 1, 2003

By N. R. Shoko, J. Chirasha

Refractory design remains the most fundamental factor in furnace construction. Refractory design details and proven technology consideration is of paramount importance to come up with an optimum furnace life and to maintain productivity in the life span of the furnace lining. The failure to produce a technically or operationally durable refractory design lining could give rise to pre-mature deterioration of the refractory lining and furnace shell. The premature failure of the furnace lining will lead to extensive heat losses, furnace bath shift, change in taphole orientation and alteration of the Pitch Circle Diameter. A combination of these were experienced at Zimbabwe Alloys? new high carbon ferrochrome furnace. The Zimbabwe Alloys experience has shown an excellent furnace performance in the first two years of operation although signs of an anomaly showed within the first six months of the new furnace. Production slowed down due to induced problems from refractory failure causing furnace distortions impacting on the availability of the furnace and smelting capacity. This paper presents the lessons learnt, measures taken to deal with the premature failure and constraints within which the situation was managed.

Jan 1, 2007