Search Documents

By I. Mc Dougall

Water-cooled copper tap-hole blocks provide an effective means of extending the life of tap-hole refractories, as the lower temperature of the refractory material inhibits wear and other damage and promotes the formation of a protective frozen slag layer. This is particularly beneficial during prolonged tapping cycles. The copper block forms an integral part of the lining, and provides mechanical support to the refractory, facilitating rapid replacement of tapping channel bricks without disturbing the surrounding lining. Safety considerations are an important design factor, and the positioning of the water channels is optimized to prevent leaks although the copper is not in direct contact with the molten fluids during normal operation. Water-cooled copper blocks designed by Tenova Pyromet have successfully been utilized on metal, matte, and slag tap-holes for a number of processes, including nickel, platinum group metals, and mineral wool.

Jan 1, 2014

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

By L. Bloch

Most mine safety initiatives in South Africa are doomed to limited success because of one simple fact: they are a-historical and un-cultural and do not deal with the serious ?legacy issues? that still negatively impact on safety, production, and relationships. We in the SA mining industry continually use imported, foreign safety concepts and systems that will not work fully in a South African context. ?The 4th Wave: Culture-Based Behavioural Safety?, as developed by Lance Bloch, an international award-winning clinical psychologist with 12 years? experience in the mining industry - focused mostly on Platinum - is making waves. He has been very successful in creating people-centred, empowered, high-performance safety cultures wherever he has worked. Not only does the 4th Wave transform the corporate culture of a mine, improving safety and production and building an environment of Ubuntu, but it also uses people?s cultures as a means of winning hearts and minds in the battle for safe production. Powerful relationships are built through engagement at all levels, leading to all being focused on the best needs of the company and its constituents as a whole. The programmes are no less than nation-building - something most necessary in the industry, with the pressures from community, unions, the DMR, and politicians. This presentation will describe and discuss the 4th Wave as an advance on previous safety technology and programmes, as particularly relevant to platinum mining in South Africa today.

Jan 1, 2012

By B. S. Xakalashe, I. J. Geldenhuys, B. Bowman, M. W. Erwee, G. A. Venter, J. Zietsman, C. Sandrock, Q. G. Reynolds

Understanding the behaviour of plasma arcs is an important part of the design and operation of direct current electric arc furnace smelting processes, which are used in the industrial production of many metallurgical commodities. In recent years numerical and computational modelling techniques have begun to illuminate the complexity of arc behaviour and how it is deeply connected to the thermodynamic and physical properties of the arc plasma. Plasma properties may be estimated from first principles using statistical mechanics methods, but this requires as input some knowledge of the composition of the gas phase that occurs over the process during smelting. In this paper the authors describe a workflow using thermochemistry software to predict the expected gas phase composition through a given process, followed by plasma property calculations using an open-source software tool that has been in development for several years. This tool, 'minplascalc' has been in development for several years and is also described in detail here. The workflow is then applied to the calculation of plasma properties of interest for a variety of historical and current pyrometallurgical processes, and the results are compared. The plasma property data are published in an open-access database for general use.

Mar 4, 2025

By A. N. Brown

Professor D. G. Krige, of the Department of Mining Engineering of the University of the Witwatersrand, received the degree of Doctor of Engineering (honoris causa) from the University of Pretoria at the Autumn Graduation Ceremony in April 1981. He was honoured an outstanding engineer for his world-renowned pioneering work in the field of statistical methods of ore valuation, or geostatistics as it has become known. Metalliferous Ore Deposits A short course on the 'Evolution of Metalliferous Ore Deposits' will be held at Rhodes University, Grahamstown, from 8th to 13th February, 1982.

Jan 1, 1981

By S. Combrink, N. Naude

Hydrocyclones are widely used in wet mineral classification applications and can be notoriously prone to wear. The methods currently used for quantifying hydrocyclone wear profiles are mostly twodimensional. In this paper it was attempted to quantify and monitor wear in three-dimensions, using a micro-CT scanner (Nikon XTH 225 ST). Hydrocyclone wear and, more specifically, spigot wear was investigated on a Multotec HC250 (Dc 250 mm, barrel diameter) hydrocyclone. The hydrocyclone is lined by a vulcanised natural rubber compound within a metal shell, with a thermosetting polyurethane spigot and vortex finder. Tests were conducted on the hydrocyclone in a pilot-scale recirculating test setup. The wear rate of the spigot was quantified by measuring the volume change within the spigot over 122 days in operation, using the micro-CT scanner. After 122 days in operation (recirculating feed materials) the wear in the hydrocyclone led to only a 13.67% loss of spigot volume. The relatively low wear rate could be related to the fact that material recirculation led to particle smoothing and a reduction in size, thereby decreasing the wear rate. This also shows the enormous influence that particle shape and size have on wear. The research was conducted with the support of Multotec, NECSA and the University of Pretoria. Keywords: Wear, hydrocyclone, micro-CT

Jan 1, 2020

By D. He, A. Yaacoubi, A. Baçaoui, K. Boujounoui, A. Abidi, K. El Amari

The effects of utilizing recycled tailings pond water from the flotation plant at the Mining Company of Guemassa (MCG) on galena recovery and selectivity towards chalcopyrite (RPb-Cu) , sphalerite (RPb- Zn), and pyrrhotite (RPb-Fe) were studied at bench scale. The results showed that recycling the tailings pond water in the lead circuit without addition of fresh water gave a good flotation performance in terms of lead recovery (Rpb) (75%) and selectivity towards the other metals: RPb-Cu (54%), RPb-Zn (60%) and RPb-Fe(65%). This allows the water to be recycled at least four times. However, increasing the d80 from 100 μm to 160 μm currently used at the MCG plant had a negative effect on the lead flotation performance.

Nov 30, 2022

By A. Eitzenberger

This paper describes a study of seismic records from the Kiirunavaara mine footwall which were interpreted in relation with numerical models developed outside the study. Seismic data was retrieved from a portion of the mine and filtered with respect to the ratio between energy carried by an event's P (primary) and S (secondary) waves (Es/Ep ratio), local magnitude, and active mining depth. The data was analysed using Es/Ep ratios and Gutenberg-Richter graphs to determine the event origin, mechanisms, and minimum magnitude cut-off. The magnitude completeness was identified by studying the b-value stability and b-value differentiation between origin sets. It was shown that, by separating seismic events into the origin components shear, complex, and tensile based on Es/Ep ratios, a representative value for the magnitude completeness can be identified for a catalogue with a convex cumulative log curve. The majority of the events were shown to be of shear-slip origin based on the recorded Es/Ep ratios, with pure tensile events constituting only about 10% of the recorded data. Spatial and temporal event location patterns were studied and compared with numerical modelling results. The comparison showed a correlation between shear-slip seismic events and volumes experiencing high differential stresses in the lower part of the footwall. In the upper part of the footwall the results did not reveal any clear correlation between observed damage in drifts and seismic event locations. The concentration of seismic events in the lower portion of the footwall is discussed in the context of rock mass displacements. The results indicate a possible connection between mine seismicity at depth and damage observations in the drifts in higher non-seismic areas by seismic softening and subsequent lateral expansion of the rock mass.

Jan 1, 2017

By X. Xiang, W. Xia, J. Yin

"TiCl4 slurry containing valuable metals is an unavoidable by-product of the titanium ore chlorination process. The recovery of these valuable metals, which include titanium, niobium, tantalum, and aluminum, is an urgent issue to tackle in the titanium industry. The results of this investigation show that the valuable metallic elements can be recovered from the slurry by evaporation in a sealed container and leaching with dilute hydrochloric acid. After evaporation at 200°C for 60 minutes, nearly 99% of the titanium was recovered in the form of TiCl4, which was formed by the reaction of the TiO2 in the slurry with AlCl3. After evaporation, metals like niobium, aluminum, and tantalum remained in the residue. By leaching with 2.1 mol/L HCl at a L/S ratio of 6:1 mL/g at 80°C for 60 minutes, the soluble metals, such as aluminum, iron, and copper were all removed from the residue, and the niobium and tantalum were further enriched in the leach residue. A concentrate containing 53.40 wt% Nb and 5.57 wt% Ta was obtained by washing the leach residue with dilute aqueous ammonia under stirring. A potential waste water purifying agent containing 263.75 g/L AlCl3 was produced by purifying the leaching solution with Al(OH)3 and modified polyacrylamide. IntrodutionTitanium tetrachloride (TiCl4) is an important intermediate in titanium metallurgy that is widely used in the production of titania and titanium sponge (Akhtar, Xiong, and Pratsinis, 1991). In conventional titanium metallurgical processes, high-titanium materials such as synthetic rutile and high-titanium slag are reacted with chlorine to produce TiCl4 in a fluidized-bed furnace. Accompanying elements, such as Al, Nb, and Fe also react with chlorine to form chlorides, which are mixed with gaseous TiCl4 (Anderson, 1917). In the condensation process, gaseous TiCl4 is refrigerated and high-boiling-point chlorides are precipitated in the liquid TiCl4 to form a slurry containing 50~60 wt% TiCl4 (Wang, Xiang, and Wang, 2012).Various methods have been proposed to recover TiCl4 from the slurry, including microwave heating and spray drying (Wang, Xiang, and Wang, 2012, Wang et al., 2010a). To date, the only way to recover the TiCl4 is to return the slurry to the fluidized-bed furnace. However, this causes fluctuations in the temperature in the furnace, resulting in incomplete reaction between titanium-rich materials and chlorine. Therefore, the slurry is often rinsed with water and neutralized by adding lime, which caused serious environmental pollution and wastes a valuable resource (Roy, Bhatt, and Rajagopal, 2003)."

May 1, 2019

By M. Mbonami, R. Pretorius, J. Miller, P. Kyony, B. Nel, N. Mautsa

Challenges due to the formation of stable froth in acid leach systems is common at many copper and Ccbalt producers. Stable froth affects downstream process, critical equipment, and operational parameters. In severe cases the froth present safety and environmental risks and increased operational costs. Solids reports in the pregnant leach solution, accumulates, and clogs launders resulting in a potential costly safety and environmental risk. Solvent extraction is operationally affected by crud formation, organic solvent and extractant losses, reduced mass transfer due to the solids carried downstream. This article reviews the generally inadequate mechanical and hydraulic solutions of froth elimination employed over the years. The recent introduction of a chemically based solution able to eliminate froth problems that can potentially turn around the situation for those who adopt the technology.

Jan 1, 2023

By C. M. D. Majola, K. E. Langerman

Energy efficiency is a cost-effective way of both bolstering energy security and limiting the harmful effects of energy use on the environment. Mining is an inherently energy-intensive activity, and the 2008 revision of South Africa’s National Energy Efficiency Strategy (NEES) set a target of a 10% reduction in energy consumption by 2015 for the mining sector. In this study, we investigate the effectiveness of the NEES in improving energy efficiency in the South African coal mining sector by surveying energy intensity at a number of operations, and analysing energy efficiency trends and energy use by process and energy carrier at an underground coal mine in Mpumalanga. Most mines surveyed exhibit an increase in energy intensity over time. At the case study mine, the increase was primarily due to increased energy use in the beneficiation and discard reclaiming processes. Trends in energy consumption are a poor reflection of trends in energy intensity, as a decline in energy consumption is most easily achieved by reducing production. A more appropriate metric for energy efficiency at coal mines is energy intensity, defined as energy use per unit of saleable product, relative to a multi-year baseline. The evidence suggests that the NEES has been ineffective in promoting energy efficiency in South African coal mines. We propose that greater success could be achieved by monitoring and reporting on energy intensity at the process level, and by incentivizing energy efficiency gains.

Sep 6, 2023

By L. von Ketelhodt

Dual energy X-ray transmission (DE-XRT) sorting is a recent development in the range of sensor-based sorting technologies available today. DE-XRT is particularly suitable for dry coarse coal beneficiation in the size range -120 mm +12 mm. In this paper, we describe the technology and show the results of a number of test runs conducted on different types of coal from the USA and South Africa. The results have shown that DE-XRT is an effective technology not only for deshaling of coal and removing pyritic sulphur but also for separating coal and torbanite. The use of dry deshaling methods will be more important as water availability becomes a greater concern. DE-XRT is one such technology which will be incorporated in future dry coal processing plants.

Jan 1, 2010

By J. H. French, O. E. Lissner

S. J. Venning (Member): The authors should be congratulated on producing such concise data from the plethora of experimental report results. Their observations on the cost of liners calls for some comment however, as the really unique feature about liners in South Africa is that they can be obtained so cheaply. Attention has been focussed on the 1961 cost of white iron at R50 per ton for chill cast block liners while manganese steel liners are reported as costing as much as R250 per ton. The former are however, a relatively heavy, simple casting with a low labour content and reasonably high percentage productivity, made from metal melted in a cupola. The capital investment to produce this type of casting is low compared with that required to produce manganese or other alloy steels. The chill cast liner block is always a production item and is cast in a permanent mould. Almost all manganese mill liners, except perhaps small aperture screens, are sold for considerably less than the R250 per ton quoted by the authors. Where a price of this nature is asked it would be because the design of the casting demanded is complicated or leaves little metal to carry the labour and other costs of production. As reference has also been made in the paper to liner costs in America, prices for similar types of liners obtained during a visit to Canada and the U.S.A. in 1961, could be of interest: Material Price per Location short ton Ni-hard R250 Elliot Lake Body liners block type Ni-Hard R300-310 FAS New York Mn Steel R280-290 FAS New York Screens (grids) slotted Cr.Mo. Steel R600 FAS New York hole Ni-Hard R320 Elliot Lake At this time the price of comparable manganese steel block type liners on the Witwatersrand was between R145/R155 per short ton. White iron in Canada was then quoted at about R150 per ton, but as Ni-Hard gave a life of at least two to twoand-a-half times that of white iron, it was a much more attractive proposition particularly when relining and down time costs were taken into consideration. There is little doubt that most foundries would welcome clear and complete specifications of the customers requirements and systematic checks to ensure that these specifications are being met. B.S.S. or other accepted standards should form the basis of these, and periodic inspections should be undertaken to ensure that only those foundries capable of complying should be included as suppliers. The authors have referred to new designs, but can the industry really call the grid and plate new when the patents were taken out during the second world war and the sawtooth block has been used for at least 35 years. Unfortunately, far too little thought and consideration are normally given to the ultimate mill liner design while the mills themselves are on the drawing boards. The position and size of the door opening, which is the key to the ultimate shell liner configuration, the drilling of the

Jan 9, 1968

By K. M. Banks

The hot ductility of in situ melted tensile specimens of micro-alloyed steels having C contents in the range 0.12?0.17% (mass %) have been examined over the 700?1000°C temperature range. An improved testing method for simulating the continuous casting process was used, which takes into account both primary and secondary cooling conditions. Increasing the N content to electric arc furnace levels (0.01% N) was found to cause a serious deterioration in ductility. V-N steel gave better ductility than Nb-containing steels due to less precipitation. From a cracking perspective, low- N steels are generally recommended but, when not feasible, a combination of Nb and V gives even better ductility. However, to be sure of avoiding transverse cracking in higher N steels a small addition of Ti is required. This resulted in a decrease in the fraction of fine particles and in accord with this better ductility. Transverse cracking of industrial slabs was then avoided.

Jan 1, 2011

By C. Chingwaru, W. Chingwaru, J. Vidmar

"Zimbabwe is endowed with rich deposits of minerals such as diamonds, platinum, coal, uranium, lithium, gold, antimony, iron, and chrome. Bioleaching has been implemented as an efficient and low-cost method to extract metals such as copper, cobalt, and gold from sulphide and/or ironcontaining ores and mineral concentrates in a number of countries around the globe. Zimbabwe, despite being a world leader in mineral wealth, has gone through years of economic stagnation which have brought with them energy shortages. Bioleaching is an innovative way to recover minerals from ores using relatively low-capital-cost and non-polluting technology. Principally, iron- and sulphur-oxidizing bacteria can be used to oxidize iron and sulphide to ferric iron and sulphuric acid, respectively, and the ferric iron oxidizes the insoluble metal sulphides to soluble metal sulphates that can be readily recovered from solution. Although some minerals such as gold are inert to biological reactions, they can be liberated using bacteria that act on certain types of ores and other minerals that co-occur with these minerals. The geology of the mineralized areas in Zimbabwe, rich in chalcopyrite / pyrite, allows a number of microorganisms to be used for the extraction of minerals by bio-oxidation. This paper reviews the potential of bioleaching in the country. IntroductionZimbabwe has rich deposits of minerals including diamonds, platinum, coal, uranium, lithium, gold, antimony, iron, and chrome. Bioleaching is defined as the use of microorganisms to facilitate the extraction of metals from sulphide or iron-containing ores or concentrates (Rawlings, 2004, 1997). Bioleaching has been shown to be an efficient (Blowes, Ptacek, and Jurjovec, 2003; Nordstrom and Southam, 1997; Schippers, 2004) and low-cost (Schippers et al., 2010) method to extract minerals in many countries around the globe. For example, aerobic Fe(II)- and sulphur-oxidizing bacteria have been shown to be up to two orders of magnitude more efficient in the oxidation of pyrite than the chemical processes (Blowes, Ptacek, and Jurjovec, 2003; Nordstrom and Southam, 1997; Schippers, 2004). Additionally, bioleaching can be used to extract minerals from low-grade ores, sulphidic waste rock dumps, and tailings efficiently (Schippers et al., 2010)."

Jan 1, 2017

By D. Visser

This paper is based on the Townlands Ore Replacement Project whereby the concept of conventional sinking of one large diameter shaft was declined and replaced with three smaller raise bored shafts. A wire line geophysical survey was done and the results indicated that a single shaft larger then 4 m diameter unsupported would not be suitable. The shafts were placed 28 meters apart measured from centre to centre. To ensure that the skin to skin pillars between the shafts remained regular and to minimise any deflection, the pilot holes were drilled with the Rotary Vertical Drilling System. The different shaft sinking methodologies are discussed explaining the risk associated with each method.

Jan 1, 2009

By D. Visser

This paper is based on the Townlands Ore Replacement Project whereby the concept of conventional sinking of one large diameter shaft was declined and replaced with three smaller raise bored shafts. A wire line geophysical survey was done and the results indicated that a single shaft larger then 4 m diameter unsupported would not be suitable. The shafts were placed 28 meters apart measured from centre to centre. To ensure that the skin to skin pillars between the shafts remained regular and to minimise any deflection, the pilot holes were drilled with the Rotary Vertical Drilling System. The different shaft sinking methodologies are discussed explaining the risk associated with each method.

Jan 1, 2009

Production caving started for Lift 2 at Northparkes in August 2004. In a period of less than 3 months, more than 10 000 seismic events were recorded. Events up to local magnitude +2.9 were induced near the mine during caving, with event rates of up to 500 per day. This paper documents the seismicity related to cave initiation and cave propagation during the initial production of Lift 2. The seismogenic zone of events initially moved at a rate of about 0.5 metres per day, accelerating to 2 to 3 metres per day after a few months of cave production. Seismic data analysis infers that the crown pillar between Lift 1 and Lift 2 was destressed over a vertical height of about 100 metres. As the seismogenic zone approached the crown pillar, a macroseismic episode occurred, with more than 20 events of at least local magnitude +1 occurring in a two-week period. Based on the seismicity recorded for Lift 2 at Northparkes Mines, a caving mechanics model is proposed. Comments and suggestions are made for seismic data analysis and design of seismic monitoring systems in block caving mines.

Jan 1, 2008

EMMES Sampling Conference BACKGROUND & INTRODUCTION ?Impala acquires toll material to supplement production from ROM ?Toll material consists of filter cake, slurry and catalysts ?Samples are collected to determine the commercial values of the lots ?Slurry deliveries projected to remain relatively constant at 120tons dry solids per month, whereas filter cake deliveries set to increase five-fold to 800 tons dry solids per month ?Due to projected increase in toll material, new sampling and offloading facility presently under construction at Impala ?Presentation will cover two projects aimed at reducing the uncertainty associated with sampling of toll deliveries ?i.e. slurries and filter cake.

Jan 1, 2005

By C. Birch

"Mineral reserve statements as well as optimizing mine planning require a block model with grades for each mining block. A cut-off grade is determined by considering the mining costs as well as the expected revenue for each block. These grades are estimated using various techniques, but in reality there is uncertainty in the grade values. These uncertainties result in two types of error. A type I error is where material is classified as ore and mined, but the true value is below the cut-off grade and the material is therefore waste. This material constitutes dilution. The type II error is where material is estimated to be below the cut-off grade and is classified as waste, whereas the true grade is actually above the cut-off grade. This material is not mined and the value is lost.This research considers the value of the lost ore and the costs of dilution under various degrees of uncertainty. Simulation using @Risk and mixed integer linear programing (Excel Solver) is used in a financial optimizer model to maximize either profit or net present value. This is applied to four Witwatersrand tabular gold deposits to investigate the impact of block grade uncertainty on cut-off grades.When optimizing for profit, value may be added by adjusting the cutoff grade slightly downwards. When optimizing for NPV, value may be added by lowering the cut-off grade significantly for the lower discounting rates. At higher discount rates, the lowering of the cut-off grades should be reduced, and in some cases an increase in cut-off grade may be required. Each mine reacted differently to the optimization and thus there is no single rule that can be applied across all tabular Witwatersrand gold deposits."

Jan 1, 2017