Search Documents

By L. A. Jordan, D. van Vuuren

A two-dimensional finite difference model has been developed to describe the reduction of kilogram quantities of dehydrated phosphogypsum. The model’s scope has been limited to focus on the heat transfer and reactions that occur within a mass of material contained in a vessel inside a furnace rather than also including the effects of heat transfer to the vessel. Changes in the heat transfer properties (k, ρ, and Cp) are incorporated as the composition of the mass changes as the chemical reactions progress. The model is validated against experimental data, with samples heated to 1000°C at 3°C min−1 while purging with nitrogen gas. A sensitivity analysis of model predictions to the pre-exponential factor of the reaction rate constant of the main chemical reaction and the thermal conductivity of the powder bed indicated that, at the envisaged process conditions, the behaviour of the system depends much more on the rate of heat transfer than on the rate of the chemical reaction. The model demonstrated a significant increase in accuracy when the thermal conductivity was modelled to increase linearly with temperature compared to assuming a constant value.

Oct 1, 2022

By P. J. H. de Graaf, S. D. N. Wessels

"Rio Tinto’s Western Australian expansion, combined with mining within structurally complex geology and increasingly below the water table, presents challenges in effective slope management to ensure safe and economic mining.The Geotechnical Management System (GMS) was developed by Rio Tinto Iron Ore (RTIO) to manage geotechnical risks identified during the design process and implementation, and to ensure feedback based on the ‘as-found’ conditions. The GMS utilizes a risk-based approach to geotechnical risk management and is centred on the geotechnical risk and hazard assessment management system (GRAHAMS). GRAHAMS is used to assess pre- and post-control risk for future potential risks (planned slopes), current risks (as-built slopes), and actual geotechnical hazards (realized risks) identified in the pit. This serves as a core operational risk management tool in identifying and prioritizing key risk sectors and management of critical controls. The system’s database reporting functionality supports effective communication of operational risks to operational personnel, as well as reporting the risk profile across operations to management.A rigorous engagement process between design engineers and sitebased engineers is implemented to ensure that key design assumptions, limitations, risks, and opportunities are understood by the site teams. This information, together with mine plan schedule details, is used to assess the design risk and develop appropriate controls. These controls typically include slope performance monitoring and slope reconciliation. The design feedback loop is closed through sharing of key slope performance and reconciliation data with the design teams.The GMS has been successfully implemented in RTIO pits and is fundamental to successful geotechnical slope management. Improved characterization of design assumptions has allowed for re-assessment of the pit design and improved hazard management in high-risk pits. The GMS, GRAHAMS, and other processes reduce the incidence of unexpected slope instability. Improved understanding of rock mass conditions has allowed for economic optimization through redesign of slopes, allowing for an improved understanding of risk and fewer unexpected conditions (surprises), hence an increased realized value."

Jan 1, 2016

By X. W. Pan

It has been found that the MnO content of a slag decreases sharply when direct current is applied to a 1T1£tal-Slagsystem consisting of liquid Mn-Si-Ccsat metals and MnO-SiO2-CaO-AI203 slag in graphite crucibles. This paper reports a preliminary investigation into the electrochemical effects of direct current on the metal-slag system, the silicon content of the metals, and the MnO content of the slag. The results show that, when a direct current of 7 A is maintained, the MnO content of a metal containing 10 to 11 per cent silicon by weight is reduced rapidly from 26,5 to 17,2 per cent by weight. This reduction seems to proceed further when the process is continued. When the direct current and the voltage are kept constant at TA and 4 V respectively, the MnO content of a metal containing 1 to 2 per cent silicon by weight is reduced to 1 from 25 per cent by weight, which results in a manganese yield of 96 per cent.

Jan 1, 1995

By E. M. Sacris

The semi-autogenous grinding mill is the bottleneck whenever treating hard and finely fragmented ore at Benguet Corporation's Kaline Concentrator. Low milling rates result from very high and fluctuating mill power draw. Attempts to use a mill horsepower control loop to regulate feed rate were unsuccessful because of operational upsets caused by fluctuations in feed rate on downstream operations. The objective of the computer control was to maximize tonnage throughput by stabilizing the power draw at a high but safe level without upsetting subsequent operations. The semi-autogenous mill is operated in closed circuit with a stationary screen. Instrumentation consists of a feed weightometer, a power transmitter to measure mill load, a headwater flowmeter and an ultrasonic level sensor to measure the mill discharge sump level. A 64 k-byte FOX-3 Foxboro computer processes field data from various sensors and manipulates the input control variables. These variables are the fresh feed rate and the headwater flowrate. Feed rate is controlled through a supervisor-type computer program aimed at maximizing and stabilizing power draw. The control scheme was according to how the operators responded during an operator-directed automatic control mode. Mill dilution is similarly controlled. Results achieved reflect a 3% increase in tonnage milled because of the reduction in control variability that ensued.

Jan 1, 1987

By P. P. Kim, M. Tangstad, T. A. Larssen

"The kinetics of MnO and SiO2 reduction in SiMn slags based on Assmang/Comilog ore and HCFeMn (highcarbon ferromanganese) slag were investigated between 1500 and 1650°C under a CO atmosphere. The results showed that charges containing HCFeMn slag had relatively faster reduction rates than those without. The difference in the driving force for MnO reduction was insignificant among the SiMn slags at 1500°C, which implies a low contribution of the driving force for reduction rate. The slag viscosities were also rather similar, around 1 poise at 1500°C, which could not explain the different reduction rates. Instead, the different charges containing various sulphur contents are believed to give rise to the varying reduction rates. The estimated activation energies for MnO reduction were around 500–920 kJ/mol for charges containing HCFeMn slag, and between 250–300 kJ/mol for those without. Based on the estimated kinetic parameters, the considered rate models were able to describe the reduction of MnO and SiO2 in SiMn slags between 1500 and 1650°C. IntroductionManganese ferroalloys such as ferromanganese (FeMn) and silicomanganese (SiMn) are important ingredients in steel production due to the beneficial effects of manganese on the physical properties of steel. Mn enhances the strength, toughness, and hardness of steel products, and both Mn and Si are used as deoxidizers to prevent the development of porous structures (International Manganese Institute, 2014; Olsen, Tangstad, and Lindstad, 2007; Subramanyam, Swansiger, and Avery, 1990; Tomota et al., 1987).The thermodynamic background of manganese ferroalloys is well established (Olsen, Tangstad and Lindstad, 2007), but kinetic information is rather scarce, especially for the SiMn process (Tranell et al., 2007; Tore-Andre Skjervheim, 1994). The absence of kinetic information makes it more difficult to understand the reduction mechanisms of MnO and SiO2. It is not clear how different raw materials affect the SiMn process. The main metal-producing reactions in the SiMn process are described by Equations [1] and [2]:"

May 1, 2019

By J. Rajala

The Kupol mill facility processed a high grade free milling gold/silver ore containing 28.2 g/t Au, 324.8 g/t Ag and approximately 0.5% pyrite during 2008 operation. Gold predominantly occurs a selectrum in the ore and silver is predominantly present in the forms of acanthite, stephanite, pyrargyrite and proustite. Mill start-up was in mid-May 2008 and the mill reached the design throughput of 3 000 tpd in October. The ore was ground to approximately 70%?53 microns. A Knelson Concentrator recovered 9.8% gold and 0.5% silver. The gravity tails reported to a cyanidation circuit that has 14 hours pretreatment and 116 hours leaching. The slurry from cyanidation was then processed by counter current decantation (CCD) thickening to wash and separate the leach residue from the pregnant leach solution. Precious metals are recovered fromthe pregnant solution using the Merrill-Crowe process. The washed CCD leach residue slurry is treated with calcium hypochlorite to destroy cyanide and then sent to the tailings impoundment. Leaching is performed with a new technology called ?CELP? (CANMET Enhanced Leach Process). The Kupol mill overall gold and silver recoveries for 2008 were 95.4% and 85.6% respectively, which were 2.8% and 7.5% higher than targets. Gold and silver extractions in the leach circuit were 94.2% and 84.5% respectively. Leach profiles indicated that gold extraction reached a plateau in the 4th tank while minor silver dissolution occurred in the 5th tank. With the CCD circuit included, total gold and silver extractions increased to 95.4% and 86.6%, respectively. Optimization of the leaching strategy made it possible to reduce sodium cyanide concentration to as low as 410 ppm without compromising precious metals extractions. Silver was effectively leached from the refractory silver minerals because CELP produced more oxidized mineral surface relative to the conventional cyanidation leached mineral surfaces. The average cyanide consumption for 2008 was 1.3 kg/t. The new leaching technology proved to be very robust and performed efficiently even with changes in feed grade and ore mineralogy. Laboratory experiments produced results that were indicative of plant performance. The robustness of the technology and the laboratory test work contributed to the success of the Kupol mill start-up.

Jan 1, 2009

By C. T. O’Connor

Since the first IMPC took place in London in 1952 there have been many developments in our understanding of flotation, both in terms of chemical and physical factors influencing the process. Many of these developments have been captured in the proceedings of thirty congresses that have taken place since that first event, as well as in numerous journal papers and special volumes dedicated to flotation. This paper attempts to highlight the individual contributions which many eminent researchers and engineers have made over the past 70 years towards extending our understanding of, especially, the effects of chemical factors on flotation. Although the focus is mainly on more fundamental aspects, it seems that the ‘pull’ of practice has often preceded the ‘push’ from laboratory-based research. As the fundamental understanding of the role of chemical factors on flotation continues to be developed, the major challenge remains to transfer this knowledge effectively into the domain of operations of this profoundly complex process.

Jan 1, 2020

By L. Roux

The initial evaluation of a coal deposit often raises uncertainty with regard to the accuracy of the reported Resources and Reserves. Reconciliation of results from mining and beneficiation with the original raw field data highlights deficiencies in original estimations. Credible Resource and Reserve estimation forms the basis on which an entire mining enterprise is motivated, initiated, funded, and established as a commercially viable proposition. This is required for sustainable extraction purposes and to support vital downstream industries such as power generation. Accurate determination of the density of the matrix of the material being evaluated is the key to credible values being obtained for Resources and Reserves. Losses between 15% and 20% of the Resource/Reserve can be realized if incorrect densities are applied to the tonnage derivation. Coal plies and particles have different relative densities, determined by the maceral composition, rank, and mineral and moisture content. These factors in turn contribute to the moisture, volatile matter, ash and carbon contents of a coal, which affect the overall density of the raw coal. More specifically, the relationship of ash to density and the effective matrix porosity were found to be critical in solving the greater majority of the problems in predictive calculations. A major deficiency identified is the inability to determine effective porosity, allowing absorption of adventitious moisture and altering the mass of the core sample. Although the volume of the raw material is altered through crushing, the change in mass after controlled air-drying, used with the original geometrical volume of the raw material, provides a credible air-dry density and allows the determination of the volumetric change related to effective porosity. This parameter can be validated through the evaluation of proximate ash using the ash-adjusted algorithm and a correction for the inherent moisture applied to also give a credible relative density value for an air-dried sample. A combination of theoretical, empirical, and reconciliatory evaluations of the available data, taken from the exploration phase through the mining process to final production, has shown that an integrated approach using the ash-adjusted density (AAD) methodology, in conjunction with other evaluative techniques, provides credible results with a considerably higher degree of accuracy than is currently possible.

May 1, 2021

By I. Cerny, M. Vanek, J. Hubácek

"SWOT analyses and the closely related TOWS matrix are frequent starting points for an organization to develop its strategy. The paper deals with the evaluation of the TOWS matrix and presents three novel approaches to evaluate the different factors of the TOWS matrix, namely (1) approach to evaluate the factors with identical weights; (2) approach to evaluate factors with their weights determined within the different quadrants of the TOWS matrix; and (3) approach to evaluate factors with weights determined within the whole TOWS matrix. The third approach has two variants. The proposed approaches to evaluate the TOWS matrix were tested on a SWOT analysis of a significant mining company in the Czech Republic. The results imply that the strategy W-T (weaknesses-threats) is recommended in three cases, while the strategy S-T (strengths-threats) is recommended once. The paper may be valuable for managers responsible for strategic planning.IntroductionThe process of human needs gratification has been closely connected with raw material resources of the planet. In the contemporary socio-economic conditions, the task of the mining company managers, apart from extracting mineral resources, is to meet the owners' intents.The managerial work itself becomes very complex. In mining companies in particular, the complexity is augmented by the characteristics of the business. Undoubtedly, the key factor is that mineral resources cannot be renewed or relocated. Stojanovi (2013) characterizes mining projects as involving great investments in finance and time, as well as consecutive decisions and a 'complex mosaic of numerous unknown factors that affect the value of the project'. He adds that mining projects are typified by a 'number of geological, technological, technical, economic, environmental, social, and financial risks' (Stojanovi , 2013).Inter alia, the managerial work may also be intese due to the dynamic internal and external conditions for the existence of any company (Vane? k, 2014). This tallies with Peter Drucker’s prediction in 1969; that the times at the turn of the millennium could be expected to be turbulent (Drucker, 1969)."

Dec 1, 2018

By F. H. Deist, M. P. Roberts

"The Collieries Research Laboratory of the Chamber of Mines of South Africa is developing a coherent system of programs to aid in the full spectrum of activities arising in the planning of new as well as operating mining enterprises. It is the purpose of this paper to describe the design and application of two subsystems in the complex.One of these subsystems is an initial version of a production simulator. This program draws upon a model of a mining enterprise and simulates the operational and financial aspects of a set of alternative mine production plans.These plans are specified in terms of proposed sequences of operations. Details such as reserves, production rates, resource requirements and so on, are taken from the model.Physically, the model takes the form of a cross-referenced data base, maintained by means of a general file maintenance system which is another subsystem described.The paper concludes with a description and analysis of the first practical application of the two programs."

Jan 1, 2014

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached to remove base metals from a concentrate containing platinum group metals (PGMs). We investigated the atmospheric leaching process to develop a better understanding of the leaching behaviour of the base metals (Cu, Fe, and Ni) and the PGMs, in particular Ru, Ir, and Rh with respect to key process variables, acid concentration, and Cu concentration under oxidative and non-oxidative conditions. With oxidative leaching, a higher initial acid concentration resulted in higher Cu, Ni, and Fe extractions, as well as faster leaching reaction rates. A higher initial acid concentration also resulted in faster precipitation of Cu, Ru, and Ir under oxidizing conditions. Under non-oxidative conditions, Ni and Fe extraction was much slower, and the effect of initial acid concentration on Cu precipitation was less pronounced. The initial Cu concentration had a slightly smaller effect on the leaching behaviour of Fe and Ni, as well as precipitation of Ru, Ir and Rh. Moreover, a higher initial Cu concentration suppressed both Ni and Fe leaching and had a slight inhibiting effect on the precipitation behaviour of Cu, Ru, and Ir.

Nov 1, 2021

Professor R. P. Plewman graduated with a B.Sc. in mining engineering from the University of the Witwatersrand in 1943, after which he had two years of military service. Mr P. W. J. van Rensburg attended St Andrew's College in Grahamstown before proceeding to the University of the Witwatersrand, where he obtained a B.Sc. (Eng.) degree cum laude in mining and metal. lurgy at the end of 1942 and was awarded the Chamber of Mines Scholarship and Gold Medal. Dr M. G. Atmore, Deputy Technical Director of the Anglo American Corporation of South Mrica, is also Manpower and Education Adviser to the Chamber of Mines of South Mrica and a Visiting Professor at the Imperial College of Science and Technology, London. Mr D. A. Vi1joen attended Queen's College, Queenstown, and then Rhodes University, where he gained a diploma in chemistry and a B. Comm. degree. Mr B. E. Protheroe, C.Eng., obtained a degree in Physical Metallurgy at University College, Cardiff, and an M.sc. in corrosion science from Swansea University. Mr N. J. Devine holds a B.Sc. in Metallurgical Engineering and a G.DE Mining Engineering, both from the University of the Witwatersrand. Dr Oskar Steffen graduated as a civil engineer at the University of the Witwatersrand in 1961, and obtained his master's degree in 1963.

Jan 1, 1984

By I. H. Clark

A variety of backfills is presently being placed in different gold mines. The backfills are pumped as slurries to stopes where they are discharged into some form of retaining paddock. The effectiveness of fill as a support medium will depend on a number of factors. These can largely include (i) inherent properties of the material, e.g. particle size, shape, distribution and com- position, and (ii) conditions of placement. The terminology required for describing backfills is introduced, and the various laboratory-measured properties are presented for a variety of fills. Finally, the properties of the fills as they are placed underground are discussed.

Jan 1, 1988

A new branch of the Institute-the Zululand Branch- was formed at the end of last year. After many months of preparation and perusal of address lists, it was realized that branch serving our members north of the Tugela was long overdue. A small steering committee consisting of Messrs John Selby, Dawid de Wet Smith, and Bill Kluckow got the branch of to a roaring start. They organized the inaugural meeting, which was held at the Richards Hotel in Richards Bay on 28th October,1993. Out of a possible 70 members residing in a 100 km radius, over half attended that first meeting!

Jan 1, 1994

The June General Meeting of the Branch was held in the St. Helena Club on Wednesday, 18th June, 1969. Mr J. G. Kirchner (Chairman of the O.F.S. Branch) was in the chair. There were also present: Eight Members: Messrs A. F. Leger, J. N. Saunders, T. Zadkin (Committee Members), Messrs M. G. Cullen, M. S. Grobler, C. J. Isaac, S. L. S. Swart, P. S. Turner. Eight Associate Members: Messrs R. Campbell, D. E. Couperthwaite, J. D. Couperthwaite, A. Hepburn, P. A. Hoffman, H. J. Reeders, R. B. Sutherland, P. R. Wheeler. Two Graduates: Messrs M. T. G. Davies, B. D. Goodwin. Two Affiliates: Messrs L. D. Hulley, K. L. Wilson. Three Visitors. Total Present: 24. Apologies were received from Mr L. O. W. Leimer. The Chairman declared the meeting open and, after extending a welcome to all visitors, said that it was his sad duty to announce the recent death of Mr. R. Jack, Associate Member. As a mark of respect to the deceased and in sympathy with the bereaved, those present stood in silence for a few moments. MINUTES OF PREVIOUSGENERALMEETING The Minutes of the Previous General Meeting held on the 19th February, 1969, which were published in the April Journal, were taken as read and their adoption proposed by Mr J. N. Saunders and seconded by Mr D. E. Couperthwaite. MA TTERS ARISING FROM THESE MINUTES There were no matters arising from these minutes. ELECTION OF SCRUTINEERS Mr V. J. Isaac proposed and Mr M. S. Grobler seconded a motion that Messrs J. G. Kirchner, J. N. Saunders and M. G. Cullen be elected scrutineers in the forthcoming election of Committee Members. GENERAL BUSINESS The Chairman announced that a visit to the South African Railways Workshops in Bloemfontein had been arranged for the 23rd July, 1969 and expressed the hope that this would be well patronised. TALKS The Chairman called first on Mr D. E. Couperthwaite to present his paper on 'Heavy media separation' and then on Mr A. F. Leger to present his paper on 'Engineering plastics'. Both presentations, which were illustrated with diagrams, proved of great interest to all members. A vote of thanks to both speakers was proposed by Mr T. Zadkin. CLOSURE After thanking the speakers, the Chairman thanked all present for their attendance and declared the Meeting closed at about 9.30 p.m. Refreshments were then served.

By N. de Koker, Y Jooste, J. Gerber

This paper presents a novel application of the boundary element method for numerical modelling of the seismic activity and hazard that is associated with the shaft pillar extraction at Bambanani mine in South Africa. In the numerical model, the tabular mining excavations are represented by displacement discontinuity elements, and to accommodate crush, shear, and fault slip seismic events, the numerical model is populated with additional displacement discontinuity elements that represent modelled crush- and shear-type failures in the rockmass. Crush-type failures are evaluated by applying the limit equilibrium method and a Hoek-Brown strength criterion, and shear-type failures are evaluated by applying a Coulomb-friction strength criteria to Ortleppshear and geological features. In this paper, the modelling results are presented as time history analyses of modelled potency from 1 January 2010 to 30 June 2022 and normalised exceedance rates for different mining periods using an upper-truncated power law. The normalised exceedance rates of seismic events that have moment magnitude Mw ≥ 1.0 are lowest for the initial mining period (26 events per year) and highest for the final mining period (218 events per year). The relative errors of the modelled potency and normalised exceedance rates are typically less than 10% or 15%, which suggests that the modelling methodology is appropriate for medium- and longer-term forecasting of seismic activity and hazard, as presented in this paper. Shorter-term forecasting is not considered in this paper.

Nov 24, 2025

By A. de Souza

On Thursday, 6th February, 1992, D. Jan Visser, the Executive Director, NPI (National Productivity Institute), addressed the Productivity Breakfast of the SAIMM-Vaal Triangle Branch in Vanderbijlpark. The Breakfast was held at the Riverside Holiday Inn, and was attended by 50 senior and middle managers in organizations in and around the Vaal Triangle, as well as by Richard Beck, the President of the South African Institute of Mining and Metallurgy.

Jan 1, 1992

By N. V. Moraka

In dealing with transformational aspects, the South African Constitution aspires for a balance between attempts to broadly represent the country’s demographics in the way in which organizations are structured and the need to maintain the necessary skills to ensure continual retention of skills for optimum and efficient organizational performance. Through the Mining Charter, government aimed to redress gender and racial imbalances in the mining industry as part of transforming the demographic representation of mining companies to include black people, women, and people living with disabilities in all job levels up to top management. While the Constitution calls for an appropriate balance between demographic representation and competency, this aspiration for mining poses challenges for companies due to the proficient and competent skills needed in this industry. To this end, the South African mining industry has been subjected to substantial criticism from government regarding the slow progress of transformation. The mining industry justifies its slow pace of transformation by pointing at inconsistent, varying legislation and definitions governing transformation, limited skills available from historically disadvantaged groups, and cautioning not to compromise the sustainability of mining companies by marginalizing white males and white youth with the objective of addressing racial imbalances. This lack of understanding between industry and the government has led to considerable confusion regarding the accountability of stakeholders in transforming the industry. This article presents the perspectives of ten mining executives on transformation in the South African mining industry. The theoretical description of transformation, as well as other mining stakeholders’ interpretations of transformation. is presented. Qualitative data from interviews with mining executives demonstrates their understanding of transformation through rich descriptions, interpretations, and implications in their contexts. The findings demonstrate that transformation in the mining industry is not simply about race and gender, but about cultural change, a change in mind-sets, embracing diversity, equalizing rights and opportunities, and attaining social justice. Moreover, transformation is clearly a gradual process. The article concludes with a recommendation for the definition of transformation to be corroborated with the views of mining executives and that of the Constitution of South Africa. This will create an overarching, simplified definition of transformation that can be accepted and interpreted by all stakeholders.

Jan 1, 2016

Fathi Habashi, Chalcopyrite. Its chemistry and metallurgy. New York, McGraw-Hill, 1978. 165 pp. RI9,95. Loss prevention and safety promotion The Proceedings of the 2nd International Symposium on Loss Prevention and Safety Promotion in the Process Industries, Heidelberg, 6th to 9th September, 1977, are now available. Chemical reaction engineering The Proceedings of the 4th International/6th European Symposium on Chemical Reaction Engineering (4th ISCRE) held at Heidelberg, Federal Republic of Ge rmany, from 6th to 8th April, 1976, are available from DECHEMA Deutsche Gesellschaft fur Chemisches Apparatewesen, P.O.B. 970146, D-6000 Frankfurt/ Main, West Germany, at the price of DMlOO plus postage and packing. Books received The Institution of Mechanical Engineers Proceedings Volume 190. Tribos abstracts on friction lubrication wear. Published by BHRA Fluid Engineering, Cranfield, Bedford MK 43 OAJ England. Price £30 (UK), US$72 (Europe), Seawater corrosion handbook, edited by M. M. Schumaker. Noyes Data Corporation Publicity Department, Mill Road at Grand Ave., Park Ridge, NJ 07656. 494 pp. Australian mineral industry quarterly 31(1) 1978 and 31(2) 1978. Bureau of Mineral Resources, Geology and Geophysics, Box 378, Canberra City, ACT 2601 Australia. Subscriptions $8, individual number $2. Mineral and NIM reports Report no. 1996 The extraction of gold from chloride solutions. (10th Nov., 1978). Report no. 1898 Batch and pilot-plant tests on M erensky Reef ore from the Western Platinum Mine. (8th Jun., 1977; reissued 30th Jan., 1979). Report no. 1920 A mineralogical investigation of Mamatu'an and Wessels manganese ores. (15th Sep., 1977; reissued 3rd Jan., 1979). Report no. 1978 The preparation and certification of a referencesample of magnetite ore. (22nd Dec., 1978). Report no. 1998 Electrode response to the addition of zinc during the cementation of gold. (25th Jan., 1979). Report no. 2002 The spectrochemical determination of phosphorus, magnesium, and iron in phosphate rocks and sulphuric acid leach liquors. (26th January, 1979). Report no. 1992 The use of emission spectrometry for the determination of impurities in metals. (24th Jan., 1979). Report no. 2003 An electrodeless conductivity meter of improved sensitivity and reliability. (28th Feb., 1979). Report no. 2005 The spectrometric analysis of manganese-bearing materials with particular reference to ferromanganese slags and metals. (16th Mar., 1979). Report no. 2006 An examination of procedures for the analysis of dry powders by atomic-absorption spectrophotometry. (28th Feb., 1979). Report no. 2007 The instrumentation and computerization of a 25 MV.A submerged -arc furnace. (25th Mar., 1977; reissued 16th Mar., 1979). Corrosion The International Corrosion Council has decided to hold the next Internat ional Congress on Corrosion in Mainz, Federal Republic of Germany, from 6th to 11th September, 1981. Process control The First European Symposium on Real -time Datahandling and Process Control will be held in West Berlin from 23rd to 25th October, 1979. Geomechanics The 28th Geomechanics Colloquy, organized by the Oosterreichische Gesellschaft fur Geomechanik, is to be held at Salzburg on 18th and 19th October, 1979. Geosta tistics A short course on 'Geostatistics for exploration and production planning' is being conducted by the Applied Earth Sciences Department, Stanford University, California, from 27th to 31st August, 1979. Business administration The Twelfth Executive Development Programme of the Graduate School of Business Administration, University of the Witwatersrand, is to be held from 9th July to 17th August, 1979. The engineer and the law A series of four meetings on the above subject is being conducted by the Measurement, Computation and Control SubCommittee of The South African Institute of Electrical Engineers. Lead smelter for South Africa? The National Institute for Metallurgy and Gold Fields of South Africa are making a comprehensive joint investigation of the technical and economic viability of an integrated lead smelter. Conference on titanium The Fourth International Conference on Titanium will be held from 19th to 22nd May, 1980, in Kyoto, Japan.

Jan 1, 1979

By T. Chikande

"Falls of ground pose costly hazards to personnel and equipment and thus measures should be taken to prevent them. This study endeavours to improve the support systems used in geotechnically poor ground at a Zimbabwean platinum mine by analysing the status quo and recommending an effective support system. Various techniques were used to determine the quality of ground conditions, predict the rock mass behaviour, and to identify the appropriate rockbolt type. An analysis of the current ground control methods and their limitations was also undertaken.The results showed that the current support system and mining practices in poor ground need to be modified to improve safety and productivity. Stoping overbreak is influenced by poor ground conditions and the explosives currently used. The use of emulsion is recommended to replace ANFO. Redesigning of pillars is also recommended in poor ground conditions. An evaluation of the current roofbolt system indicated an opportunity for improvement. With new insight on the performance of the shorter length roofbolts currently in use, a new support system was recommended taking into consideration cost-benefit analysis. Barring down using pinch bars in poor ground was seen as a risky and time-consuming exercise, hence the use of mechanical scalers is recommended to achieve zero harm and to meet production targets. Smoothwall blasting is recommended in poor ground to minimize excavation damage. Other recommendations include the use of hydrological surveys to determine groundwater levels and implement corrective measures. Both empirical and numerical modelling approaches need to be utilized in determining the optimum support. IntroductionThe presence of geological discontinuities such as faults and joints weakens the rock mass. Adequate support is critical in achieving zero harm in underground mines. This paper reviews the current support systems used in poor ground conditions at a Zimbabwean platinum mine. The area of research is located on the Great Dyke of Zimbabwe. The mine exploits platinum group elements (PGEs) and base metals. It is shallow, having a maximum depth of less than 300 m. The Great Dyke is the second largest reserve of PGEs, following the South African Bushveld Complex (Oberthur et al., 2012). It is a linear layered intrusion that extends for about 550 km with a maximum width of 11 km (Prendergast, 1989). The generalized section of the Great Dyke is almost like a trumpet, comprising layers that dip towards the centre. The reef exploited at the mine, the Mineralised Sulphide Zone (MSZ), is located in the pyroxenite layer, which is hosted in the ultramafic sequence. The MSZ is a uniform layer about 2– 3.5 m thick, dipping at around 10–14° from surface outcrop towards the axis of the basin, and located between bronzite and websterite horizons. The visible disseminated sulphide mineralization shows a typical and consistent vertical distribution of platinum group metal (PGM) and base metal values. The research was undertaken to review the current support systems used in geotechnically poor ground conditions in a bid to improve both safety and productivity."

Jan 1, 2016