Search Documents

By H. L. Riley

Cleaning and handling of fine coal are generally conceded to be more difficult problems than preparation of the coarser sizes. Increased mechanization in the coal-mining industry has, in general, resulted in an increased percentage of the fine sizes in the total coal mined. If the coal fines are cleaned by wet methods, the minus-1/16-inch square-mesh particles cause most of the sludge and slurry problems encountered in preparing wet coal. Equipment that separates coal from refuse on the basis of specific gravity is not efficient on sizes that, because of their fineness, do not follow the same laws of hindered settling as the larger particles. Probably the best solution of fine-coal cleaning problems is to use other methods, such as flotation, that utilize other physical characteristics than those determining hindered-settling ratios. Regarding the type of flotation known as the Elmore vacuum-flotation process there has been a scarcity of data and information available in this country. An investigation has therefore been made to obtain additional date and information on this process under laboratory conditions. During this investigation an effort has been made to evaluate the relative efficiencies of vacuum and mechanical laboratory froth flotation cells. The investigation included float-and-sink, screen-sizing, and flotation tests on 2 different samples of 14-mesh to 0 raw coal and an a sample of slurry from the settling-tank overflow of a typical washer. One raw-coal sample was obtained from the American bed and represented a type of coal that is relatively easy to clean. The other raw-coal sample was from the Mary lee bed and represented a type considered difficult to clean.

Jan 1, 1954

By Leslie S. Rubin

A ventilated helical boost pump was developed that can handle varying flow rates and/or solids concentrations while operating at a single rotational speed and without computer assisted feedback controls. The boost pump developed and briefly tested during this program was designed to accomodate flows suitable for a 3-in. diameter pipeline. The boost pump's ventilated design provides the automatic pressure regulation needed to meet the system's requirements for supporting transient pipeline flow.

Jan 1, 1984

By H. M. Cooper

Many analysts have had difficulty in obtaining accurate and consistent determinations of the volatile matter in low-temperature coke when the usual standard method for coal was followed. The tendency is toward too-high results, due to mechanical losses which are extremely difficult to avoid or control. With cokes there also may be an error due to excessive oxidation of the fixed carbon. Much of the earlier experimental work on the volatile-matter determination in coal, such as that of Parr,5 Fieldner and Davis,6 and others, 7 has been on the effect of time, temperatures, shape and size of crucibles, method of applying heat, and type of furnace, all of which data has evolved the present A.S. T. M.8 standard method for volatile matter in coal and coke. It is not the purpose of this investigation to deal directly with the above phases of the procedure, but rather to study some of the factors affecting she results in those types of fuel which give erroneous results due to mechanical losses.

Jan 1, 1932

By Elbridge W. Gresseth

Rock deformational structures in a deep mine were analyzed by petrofabric techniques to learn (1) the relative magnitude and direction of the principal stresses involved in tectonic deformations prior to mining, (2) the preferred orientation of rock planar discontinuities which define rock anistropy prior to mining, and (3) the relationship of mining-induced rock failure to inherent rock stresses and inherent rock anisotropy. Rock fabric elements used for petrofabric analysis consisted of bedding planes, faults, joints, fractures, foliation, sericite plane (001), quartz axis [0001], quartz deformation lamellae, and microfractures. Structures and structural symmetries from different areas within the mine and from different scales of observation were compared to learn the nature of rock anisotropy and the orientation of the principal stresses defined by rock deformations. Analysis of such fabric as regional and macroscopic faults, b-c joints, quartz [0001], sericite (001), and microfractures, indicate that during the epochs of tectonic deformation, the maximum and minimum principal stresses were horizontally oriented and acted along northwest and northeast axes, respectively. This condition of regional stress appears to have continued during folding and the associated period of faulting. The most recent tectonic deformation represents a rotation of the minimum principal stresses into a vertical position, as shown by the development of a tensile joint system, quartz deformation lamellae, and microfractures. Good interscale correlation and statistical homogeneity of tectonic fabric indicate a stress field homogeneity in this area during tectonic deformation. Rock physical anisotropy is genetically associated with tectonic fabric and consists of preferentially oriented planar discontinuities intersecting along a nearly vertical axis. The mining-induced deformations were correlated with the inherent rock anisotropy which either directly controls or greatly affects their development. This phase of rock deformation shows a greater degree of stress field heterogeneity than was the case with tectonic deformations This is explained as a result of nonconfinement afforded by underground openings and the increase in ground stresses due to mining activity"

Jan 1, 1968

By S. J. Davenport

The increased consumption and importation of fluorspar and cryolite (1)3/ in recent years, and especially the addition of fluorine compounds to drinking water in the United States, have aroused renewed interest in the properties of such compounds and possible health hazards incident to their use. It has been suggested that the issuance of a revision and elaboration of Information Circular 7311, The Hazards of Hydrogen Fluoride Poisoning in the Mineral and Allied Industries, which hay been out of print for some time, would be opportune. Fluorine minerals have been known since the Middle Ages. Fluorine was isolated in 1886 by Moisson (2).

Jan 1, 1954

By J. F. McIlwain

The Bureau of Mines has investigated fumes generated by selected welding electrodes used in mines in order to help determine their relative health hazard potential. Fumes were generated and collected in an enclosed chamber for subsequent generation rate and chemical constituent determination. Shielded metal arc electrodes from the following groups were tested: AWS types E308-16 and E310-16 stainless steel, ECoCr-A Co-Cr hardfacing alloy, ENiCr Ni, an Mn-Cr buildup alloy, E7018 carbon steel, and EII018-M low-alloy steel. Flux-cored wire electrodes of this last group also were tested. Fume generation rates and the chemical composition of the fumes were measured. From these data, exposure in-dices were determined, which give a relative measure of the health hazard potential of using the electrodes. The effect of welding onto build-up alloy layers on the fume composition also was examined for five of the higher alloy groups.

Jan 1, 1987

By Eric G. Kok

Complying with respirable dust standards is presently a critical problem for many longwall faces equipped with double drum shearers. Results are presented of research performed to increase the quantity and optimize the distribution of the water supplied to the shearer drums to control the shearer operator dust exposure. The effect on the total respirable dust produced by the shearer was also examined. During the research effort, a simple and inexpensive manually controlled valve system was designed and implemented on a shearer to distribute the water supplied to the shearer drums. Research showed that increases in water quantities are beneficial but associated pressure increases may induce respirable dust boilover negating potential advantages. Other essential parameters such as location of shearer operator, outside spray orientation and air quantity were considered in the evaluation.

Jan 1, 1986

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nonmetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

Sixteen papers concerned with the technology and utilization of low-rank fossil fuels are presented as the proceedings of the 1973 lignite symposium. This symposium, the seventh in a series of biennial meetings, was cosponsored by the Bureau of Mines and the University of North Dakota.

Jan 1, 1974

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nomnetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By L. C. IlsLey

"There is an old saying that ""It is too late to lock the stable after the horse is stolen"". Is not this just what is being done by many mine operators today when it comes to buying safe electrical equipment for gaseous and dusty coal mines?The ""open type"" of electrical equipment or even the ""half safe"" type represents the unlocked stable. After the mine disaster, and after men have lost their lives, the lock is put on - that is, safer equipment is installed.For example, an open type of electric coal drill was used in a gaseous mine in West Virginia, This was the probable cause of the death of 27 men. A half safe type of electric coal-cutting machine was used in a gaseous mine in Pennsylvania. This was likely the cause of the death of 36 men. An unapproved, unsafe type of flame safety lamp was used in a gaseous and dusty mine in Utah. This was the all¬eged cause of the death of 171 men. All three disasters happened within the last six months, and seem to have been avoidable if proper equipment had been used.It is understood that more rigid requirements will be enforced in West Virginia. The committee of State mine inspectors made definite recommendation for im¬proving the conditions in the given mine in Pennsylvania. The Industrial Commission of Utah have already issued new orders which will remedy the use of unsafe lamps in that State.These acts and recommendation are all good and will help prevent accidents in those States in the future. Is it not a pity that such recommendations and order were not made a little earlier before the tell of life had been exacted? Is it not a pity that other States will not take these lessons to heart and safeguard their mines before and not after disasters take place?Electric current can cause accidents in five general ways as follows: (1) By shock to persons; (2) by igniting powder; (3) by igniting gas; (4) by igniting coal dust; and (5) by setting fire to inflammable material such as timber and coal. A great many accidents from these causes are preventable if proper care is taken. Most of the accidents caused by sparks and flashes from electrical apparatus would not take place if approved electrical equipment was used. By approved equipment, the writer means equipment that has been tested and formally approved by the Bureau of Mines. So far as known, up to the present time, no disasters have been caused by sparks or flashes from equipment having the Bureau's approval."

Jul 1, 1924

By Michael G. Zabetakis

Limits of flammability of normal propyl nitrate (NPN) vapor were investigated at ambient and elevated temperatures. Minimum spontaneous ignition and decomposition temperatures were determined with laboratory apparatus over the pressure range from 0 to 4,000 p.s.i.g. Flame speeds and the detonation susceptibility of NPN vapor were measured at elevated temperatures. Stable detonation was obtained with liquid NPN at elevated temperatures, and the detonation velocity was determined to be between 4,700 and 5,100 m./sec.

Jan 1, 1962

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

By Rudolf E. Greuer

Two computer programs for the real-time calculation of concentration distributions in the ventilation system of underground mines were designed. They allow one to simulate the movement of fumes or other contaminants with the ventilating air, the calculation of concentrations at any given point and time, and the determination of the total contaminant exposure at different places in the mine. Multiple and time variable contaminant sources can be handled and recirculation is no obstacle. The, first program is based on an airflow distribution which has, in the input data, to be stated. The second program has been linked to in existing program for the calculation of airflow distributions. Two versions of this second program are provided to accommodate the two existing programs. Several executed examples demonstrate the program performance.

Jan 1, 1981

This report is the first in a "final" series of publications on the Juneau Mining District (JMD). This volume summarizes the results of Bureau of Mines (Bureau) investigations in the JMD during the period 1984-1988. Volume 2 consists of a detailed description of Bureau investigations of mineral de-posits, prospects, and occurrences. Volume 3 is a report on industrial minerals within the district. This study has identified and examined more than 300 mines, prospects, and occurrences containing gold, silver, copper, zinc, lead, nickel, cobalt, tungsten, molybdenum, chromium, and PGM. More than 20 of these were discovered during this study. An additional 20 prospects not mentioned in the literature were rediscovered during the JMD study.

Jan 1, 2012

Table A-1. Number of underground coal mines and samples collected for underground occupations, 1988-92 [ ]

Jan 1, 1997

By J. M. Kuchta

Bench-scale test methods were developed by the Bureau of Mines for use by the Department of Transportation in the classification of solid and liquid oxidizers. A burning rate test is recommended for evaluating the fire hazard of solid inorganic oxidizers when mixed with a red oak sawdust as the reference combustible. A spontaneous ignition test is proposed for evaluating liquid and solid inorganic oxidizers which may decompose violently or ignite spontaneously when unmixed or mixed with the wood sawdust under unconfined conditions. Test results are compared for various representative oxidizers and a classification system is proposed for use in the government transportation regulations.

Jan 1, 1972

By E. C. Perkins

As part of a program for developing methods of using domestic titanium deposits, the Bureau of Mines investigated methods for chlorinating titanium slags prepared from titaniferous minerals by electrosmelting. Titaniferous slags were made from ilmenites in the following deposits: Valley County, Idaho; Trail Ridge, Fla.; Aiken, S. C.; and Maclntyre, N. Y.; titaniferous magnetite from Iron Mountain, Wyo., were also evaluated. The tests were made in two chlorinators, a 4-inch and a 36-inch unit. Preliminary testing was done in a 40-millimeter bench-type unit. Chlorine gas was contacted with a loose mixture of titaniferous slag and carbon at a high temperature to form titanium tetrachloride. The moving-bed system used in this work involved a downward movement of feed countercurrent to the chlorine flow, and residues continuously removed from the bottom of the reactor. The performance characteristics of these slags depended on their composition, which varied widely according to the geographic source of the ore. The results showed that all but two of the slags could be chlorinated as effectively as rutile, converting 70 to 80 percent of the titanium to the tetra-, chloride. The two slags that proved difficult were made from New York ilmenite and Wyoming titaniferous magnetite. These slags contained enough magnesium to cause clinkering, which necessitated that the bed be prematurely withdrawn before more than 70 percent of it could react. The iron content of the slags did not interfere with operating the chlorinators. The data from the 4-inch and the 36-inch units were in agreement on the relative amenability of the slags to chlorination.

Jan 1, 1962

By M. R. Geer

Information on the performance of coal-cleaning equipment is necessary to provide a basis for evaluating the performance of existing plants and projecting that of new plants. Performance data can contribute greatly to the wise selection and effective use of coal-washing equipment. The Bureau of Mines has published information on the performance of several commercial plants, as well as of some laboratory-scale equipment, 5 (2-9, 11, 12, 17-12, 21-25) from time to time for a number of years. A more intensive program to provide such information for all the principal types of cleaning equipment is underway. The present evaluation of table performance is part of this program.

Jan 1, 1962