Search Documents

Etching solutions containing hexavalent chromium ions (e.g., chromic acid) are used in brass finishing, printed circuit board etching, preparation of plastic for plating, anodizing, and various other industrial surface treatment operations. As the solutions are used, hexavalent chromium ions are reduced to their trivalent state, contaminants accumulate in the solution, and the effective acid concentration is reduced. When the etching rate becomes unsatisfactory for the particular operation, the solutions are discarded. This is a problem because the discarded solutions are pollutants, and because replacing the etching solution is expensive. The Bureau of Mines has developed a process for regenerating these spent solutions and returning them to the surface treatment operation without interrupting the etching process. An electrolysis cell containing anode and cathode compartments that are separated by permeable membranes, is used for regenerating the spent solutions. The spent chromic acid solution is fed to the anode compartment and sui (uric acid is circulated in the cathode compartment. Application of a steady electrical potential of a few volts dc across the electrodes causes the copper ions and other contaminants in the spent solution to migrate through the membrane to the cathode compartment where copper is plated onto the cathode. Zinc and the other contaminants remain in the sulfuric acid. At the same time, the complex, trivalent chromium ions in the spent solution are attracted to the anode where they are oxidized to their original hexavalent state. The regenerated solution in the anode compartment is then recycled back to the plant?s etching operation for reuse.

Jan 1, 1980

By Bill M. Stewart, Philip W. Patton, Curtis C. Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines we revisited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

By H. William Zeller

The Bureau of Mines performed laboratory research to determine the effects of a barium-based fuel additive on diesel particulate emissions. The test engine was typical of types used to power underground coal min-ing equipment. Test parameters consisted of baseline measurements without additive, three fuel additive concentrations, and five steady-state engine loads, all at 1,200 r/min. Additive effects on soot mass concen-tration, opacity, particle size distribution, volatile fraction, and NOx emissions were determined. Important findings are as follows: Using the manufacturer's recom-mended additive concentration increased the gravimetrically measured mass of particulate by 30 to 80 pct at four of the five steady-state load conditions. Soot measurements by optical methods did not agree with those by gravimetric techniques, for additive-treated fuels. The additive reduced volatile hydrocarbons adsorbed on filter deposits by up to 50 pet. At most engine loads, carbon particulate was also reduced. About 40 pet of the barium added to the fuel was accounted for in the exhaust. The health implications for miners were considered, but no firm conclusions were drawn or recommendations made because the results are for steady-state conditions, which may not be representative of real-world operation of diesel-powered equipment underground.

Jan 1, 1987

By W. H. Young

THE BITUMINOUS coal and lignite industry declined slightly in 1961, compared with the 1960 figures. All of the major items, production, consumption, average value, exports, and employment, declined. Even the steady upward trend in mechanization failed to materialize; the percentages of total tonnages mechanically loaded and cleaned remained the same as in the preceding year. However, tonnage per man per day increased from 12.83 tons in 1960 to 13.87 tons in 1961, owing partly to the increased tonnage produced by continuous mining machines. Also, the percentage of total production mined by stripping and by augers increased slightly. Production.-The output of bituminous coal and lignite in the United States in 1961-403 million tons-was 3 percent less than the 416 million tons produced in 1960. Production was retarded in 1961, owing largely to the business recession and reduced exports.

Jan 1, 1962

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 241,502 employees worked in surface mining locations in 2003, corresponding to 212,113 full-time equivalent (FTE) workers. • Surface employees accounted for 84.6% of all mining employees. • The majority of surface employees (73.7%; n = 177,927) were mine operator employees as opposed to contractor employees. • Stone operator employees comprised the greatest percentage (27.2%; n = 65,743) of surface employees.

Feb 1, 2005

By F. P. Miknis

Previous studies at the Bureau of Mines have shown that broad-line nuclear magnetic resonance (NMR) techniques have potential applications for rapid evaluation of oil-shale deposits. In a continuation of this study the techniques of pulsed NMR have been applied in a similar manner. The basis for the pulsed NMR oil-shale assay method lies in the assumption that the free induction decay (FID) amplitude following a 90° pulse is proportional to the potential oil yield. This assumption was tested on two groups of oil-shale samples, numbering 141 and 263 samples, from two different oil-shale cores. For both groups of samples a small number were selected as calibration samples. Free induction decay amplitude measurements were made on the 141 and 263 samples. The best least-squares regression line was obtained for the calibration samples, and the oil yields of the remaining samples were calculated using the slopes and intercepts obtained in the regression analyses. The agreement between measured and calculated oil yields was good, the indexes of determination being 0.93 and 0.89 for the groups of 141 and 263 samples, respectively.

Jan 1, 1974

By Larry A. Haas

The U.S. Bureau of Mines investigated the use of organic binders as substitutes for bentonite in agglomerating iron ore concentrate. Over 30 organic binders were evaluated at several dosage levels in laboratory tests. The binder groups producing the greatest green pellet strengths were natural gums (guars carboxyl methyl celluloses) and gelled starches. The nongelled and alkalized starches, starch acrylic copolymers) wood-related products, and dairy products were less effective but better than bentonite. The highest wet pellet drop numbers were obtained with binders that had a medium plate water absorption value (>500 and <10)000) in distilled water and a high slurry viscosity (>75 cP) at 6 pet solids. The highest dry compressive strengths were obtained with binders that gave the highest adhesive tensile strength (>4 kg/ cm2) on iron oxide lap-joint substrates. Pellets with 0.1 pct organic binder had lower compressive strengths and reduction disintegration indices than those with 1 pct bentonite, but higher reduction rates. Pellets with carboxyl methyl cellulose and gelled starch had higher softening temperatures than those with bentonite. Overall, the most promising binder is gelled starch. Its price makes it more cost effective than carboxyl methyl cellulose, and its pellets have metallurgical properties superior to those of bentonite pellets.

Jan 1, 1989

By W. M. Myers

Water has been commonly used as a collecting medium in many instruments employed in the sampling of dusty atmospheres in mines** add industrial plants, and for this purpose has much to recommend it, particularly the following factors:1.,Water is a very efficient dust collector.2.,Distilled water of great purity may be readily obtained at slight expense. The analytical error introduced by the extremely small amount of foreign matter in carefully distilled water is very small,3.,Water is a very convenient medium with which to work as all the analytical operations of diluting, aliquoting, and filtering are readily and speedily carried out. Water has therefore been used extensively in such instruments as the Palmer apparatus, the Greenburg-Smith impinger, and the dust collector recently described by Drinker, Thompson, and Fitchet. The Bureau of Mines has conducted investigations in many metal-mining districts of the country, determining of dust the nature and amount of dust present in working places, its effect the health of workers, and what precautions may be taken to decrease the hazard of exposure to dangerous dusts. The Bureau is therefore interested in any factor that affects the accuracy of dust sampling.

Nov 1, 1923

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

By Joseph W. Martin

The Bureau of Mines investigated the backscattering of low-energy gamma rays as a method for rapidly determining the incombustible content of coal mine dust. In this method, 60-kev gamma rays from americium-24l penetrate the dust and are reflected by elements in the dust to a thin crystal scintillation detector. The number of backscattered gamma rays is proportional to the incombustible content. Tests of 40 dry, mine-dust samples containing 50 to 100 percent inert material show an average error of 2 percent. Calibration of the apparatus is necessary for each rock dust to account for variable composition. Results for samples containing more than 6 percent moisture are subject to error, but the values are lower than values obtained by chemical analysis, and thus fall on the safe side. Development of a small portable meter based on the backscatter principle appears feasible. Such a meter would find application within coal mines to check the effectiveness of rock dusting procedures.

Jan 1, 1968

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau&apos;s first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the. 1900&apos;s and was surface mined in the 1940&apos;s. In the winter of 1961~62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but, not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report, although considered part 2, is actually the last of a five-part series that describes the Calamity Hollow Mine Fire Project. It was written last because it involved the analysis of a substantial body of data describing in detail the results of a continuous 4-month burnout operation. The first report, part 1, describes the design and construction of the field installation. Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and part 5 describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is suffIcient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water injection-fume exhaustion quenching procedure are planned.

Jan 1, 1989

1. In 2002, a total of 256 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Metal mines were the smallest mining sector,1 comprising 1.8% of all mining operations. • Gold mines comprised 44.1% (n = 113) of all metal mining operations. Other types of metal mines were copper ore (n = 31; 12.1%), iron ore (n = 25; 9.8%), and lead and/or zinc ore (n = 21; 8.2%). • Nevada is the state with the largest number of metal mines (n = 53; 20.7%).

Jan 1, 2004

By Manuel Gomez

A computerized, interpolative mapping technique based on the moving average method was shown to be adequate to estimate the between-drill-hole values of coal-seam variables. The forecasting of the spatial distribution of coal properties along the seam was of three kinds: (1) Estimation of the variable of interest on a regional basis from widely spaced sample points, (2) prediction of coal properties for product control from closely spaced data, and (3) prediction of coal properties for specified benches, or layers of the coal seam, from closely spaced sample points. Estimates obtained with the computerized, interpolative mapping procedure were useful in the delineation of seam thickness, elevation, and overburden and in the estimation of sulfur and ash concentrations during the early phases of exploration. This grid interpolation technique was found adequate to adjust between-drill-hole values for trends resulting from the combined effect of several variables on a measured response. This information, coupled with statistical and geologic data that can be obtained in the exploration phase of mining, enlarges the information base available for coal-mine development planning, energy forecasts, and environmental control associated with fossil fuel power generation.

Jan 1, 1972

By K. K. Kelley, L. B. Pankratz

The heat contents of four silicate minerals -- akermanite , cordierite , gehlenite , and merwinite --were measured from 298 ° to around 1,700 ° K by the dropping method . The results were compiled into tabular and equation forms suitable for thermodynamic calculations . The heat contents of these compounds are nearly additive with respect to their constituent oxides .

Jan 1, 1964

By I. AITKENS

Quartz maintains a rather conspicuous position among gem stones , despite its being the commonest and, in its natural form, the most easily recognized of mineral substances . This prominence is due primarily to the extensive use of amethyst , which provides stones of the finest violet color , and also to the wide employment of yellow quartz ( citrine ) which is called topaz by jewellers and vies with the true topaz in color and brilliance . Unlike many less costly gem materials quartz is hard and durable .

Mar 1, 1932

By James H. Russell

Several solid sorbents were compared for their effectiveness in removing sulfur dioxide from flue gases. The materials were tested for the rate of sorption and capacity at about 300° C, and rate of regeneration around 700° C in thin beds and in 4-inch-diameter fluidized beds. Rates of material loss were also estimated. The sorbents tested included three samples of alkalized alumina, two samples of sodium carbonate-impregnated alumina, and one proprietary sample of porous silica impregnated with copper and iron compounds. The results showed that all the alkalized aluminas had good sorption capacities and rates, required high temperature regeneration, and suffered excessive material loss; the sodium carbonate-impregnated aluminas (1) had high sorption rates but barely adequate capacities, (2) required high temperature regeneration, and (3) suffered excessive material losses; and the copper-iron impregnated silica suffered only slight material loss and could be regenerated at a relatively low temperature, but the sorption rate and capacity were too small. None of the sorbents met all the arbitrary performance criteria that follow: sorption rate constant of 1 min-1, sorption capacity of 0.1 g sulfur per g sorbent, regeneration rate constant of about 0.075 min-1 at a reasonable temperature, less than 0.07 pct per hour material loss during operation, and a chemical life of 500 cycles.

Jan 1, 1971

By H. E. Hilliard

The Bureau of Mines investigated hydrometallurgical procedures for concentrating precious metals from a mechanically processed metal fraction of obsolete military electronic scrap. Feed material for the leaching procedures described in this report was the high-tension-separated metal concentrate obtained as a fraction from mechanically processing partially stripped electronic units. Initial pretreatment with a 20-wt-pct-NaOH solution solubilized most of the aluminum. After washing, the resulting residue was incinerated to destroy any organics attached to metal particles. The incinerated residue was leached with 20-vol-pct H2S04 solution using two methods, countercurrent pressure and ultrasonic-aided leaching to solubilize the base metals, predominantly copper. Silver was recovered from the base metal leach residue using 50-vol-pct HN03, and gold contaminated with several percent palladium was recovered from the silver leach residue using aqua regia. The impure silver and gold plus palladium products represent about 1.5 wt pct of the high-tension-separated metal concentrate. Included is a three-step process evaluation study of mechanical processing of general electronic scrap and two hydrometallurgical procedures for leaching high-tension-separated metallic concentrates obtained from the mechanical processing step. Process evaluation concluded that only mechanical processing is economically viable.

Jan 1, 1985

By R. K. Koch

The vapor pressures of liquid columbium and liquid hafnium were deter-mined by the Langmuir free evaporation method as a part of the Bureau of Mines program on the study of transition metals. An electron-beam furnace with a water-cooled copper crucible was used for melting. Temperature was measured with a two-color ratio pyrometer. Least-squares analyses of the vapor pres-sure data gave the following equations: [Logp (atm) = 5 .429 -31,310 T] for liquid columbium in the range 2,740° - 3,140° K, and [Log p (atm) = 5,690 28 T] for liquid zirconium in the range 2,500° -2,810° K. Third-law evaluations of each data set gave mean heats of sublimation (298.15° K) of 175.1±3.2 kcal/mole and 148.3±1.2 kcal/mole for columbium and hafnium, respectively. Second-law standard heats of sublimation determined from sigma plots and from sigma-prime plots agreed fairly well with the third-law values. The sigma-prime plots gave standard entropies of sublimation of 30.96±0.84 eu and 33.S6±0.44 eu for columbium and hafnium, respectively.

Jan 1, 1968

By W. E. Dennis

"INTRODUCTION The strategic importance of zinc warranted investigation of the Silver Eagle zinc prospect, which was first examined by an engineer 3/ of the Bureau of Mines in January 1943.From October 12, 1943, to March 16, 1944, the Bureau explored the deposit by trenching, core drilling, and sampling to establish the amount and grade of ore and to test for the presence of sulfide-ore minerals at depth.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Oct 1, 1946

By Stephen D. Cramer

The solubility of methane, carbon dioxide, and oxygen was measured in brines at temperatures from 0° to 300° as part of Federal Bureau of Mines research on the corrosion of metals in high-temperature geothermal and mineral processing environments. Solubilities were measured by the technique of extracting pure gas, dissolved at pressures where Henry&apos;s law was applicable, from known volumes of brine. The results were smoothed with respect to temperature. The solubility, expressed in terms of the Henry&apos;s law constant, reaches a maximum at temperatures ranging from 60° to 100° C for methane and oxygen, and from 160° to 170° C for carbon dioxide. The Henry&apos;s law constant increases, that is, gases are salted out of the brines, in the presence of dissolved salts. Salting-out coefficients are strongly dependent upon temperature. The temperature dependence of the Henry&apos;s law constant for geothermal brines is different from that for sodium chloride brines owing to the more complex chemistry of the geothermal brines. The solubility of oxygen and carbon dioxide in brines exposed to air saturated with water vapor and at a total pressure of 760 mm Hg is reported for temperatures from 0° C to the normal boiling point.

Jan 1, 1982