Search Documents

By W. C. Holliman

This report describes apparatus and procedure used for determining the vapor pressure of aviation gasoline in surveys of commercial aviation-gasoline characteristics made by the Bureau of Mines in cooperation with the Coordinating Fuel and Equipment Committee of the Coordinating Research Council, Inc. (CFR-CRC). The method is a modification of the Reid method, in which a mercury manor is substituted for the Bourdon-type gage of the Reid method. The method was used in earlier surveys made by the National Bureau of Standards in cooperation with the CFR-CRC, and was used in the Bureau of Mines surveys at the request of the cooperating organizations. It is designed for special research problems? particularly in vapor-lock studies, which require a precision greater than obtainable by the Reid vapor pressure method. A repeatability of + 0.01 p.s.i. average deviation from the mean may be obtained by method.

Jan 1, 1950

By R. L. Montgomery

The heats of formation of lanthanum sulfate and the enneahydrate are -939.8 ± 3.1 and -1,587.1 ± 3.2 kcal. per mole, respectively. The heat of hydration is -32.5 ± 3.5 kca1. per mole. These values were obtained from heat-of-solution measurements of lanthanum oxide and salts. Low rates of solution precluded more accurate determinations of the thermal data. The heat of formation of the chloride was similarly observed to be -256.18 ± 0.28 kcal per mole. Heats of solution and combustion of lanthanum metal yield mutually concordant results, and earlier discrepancies reported in the literature may be ascribed to impurities.

Jan 1, 1959

By Ludwig Schmidt

Investigations conducted by the Bureau of Dines pertaining to the reduction of evaporation losses of petroleum have shown that such losses may be reduced 70 to 80 per cent by the use of vapor-tight tanks equipped with vacuum and pressure relief valves, and vapor-tight thief hitches. Additional studies have shown that it is often economical to supplement this type of construction with other measures that will reduce evaporation losses still further. Water-cooling systems, insulation, and light colored paints are the measures most often used in connection with vapor-tight tanks. Painting with light colored paints probably is employed in the greater number of cases. On account of the cost of insulation, or of installing water cooling systems, the use of these methods are restricted to tanks containing gasoline or crude petroleum with a very large content of low-boiling fractions. The effect of cooling systems has been discussed in a previous report.2 In choosing paints for tanks many factors must be considered. Probably the three most important are cost, protective value, and color. Many companies have adopted a standard color for all of their tanks in this way they reduce the initial cost of paint by buying in large quantities. The tank farms of such companies usually have a neat appearance, resulting from the uniform painting of all tanks. This procedure also has advertising value. Unfortunately, most of the paints used to protect steel are of the darker colors, usually red or black. These colors accelerate the rate of evaporation. Several companies have solved this difficulty by using a dark colored metal-protective paint as a primer coat, and a paint of any desired color for the final coat. Special metal-protective primers to be used under light-colored cover coats have been placed on the market by several paint manufacturing companies.

Jan 1, 1925

By Donald J. Barnes

The Glacier View RARE Ii further planning area contains no identified mineral deposits, other than stone, which cannot compete favorably with similar deposits closer to major markets. Pierce County mining claim records show six coal claims were located in the study area between 190b and 1907; however, no coal was found at the described locations. Two coal prospects, the H.O. Lamming and Floyd Rice, are within 0.5 mi (0.8 km) of the area's west boundary (fig. 1). At these prospects, impure bituminous coal beds strike approximately north and dip east toward the study area. Analyses of samples 1/ indicated an average heating value of 2,767 BTU 2/ per pound (6,436 joules per kg). Because of the low heat value, this coal is subeconomic. Intense folding and faulting which disrupted the beds would limit the use of conventional coal mining equipment, making future economic development even less likely. Trinity Resources of Houston, Texas has leased approximately 1,404 acres (568 ha) inside the study area and an additional 1,020 acres (413 ha) adjacent to the study area for oil and gas exploration. However, no oil or gas wells are known to have been drilled in or around the study area.

Jan 1, 1983

By H. William Zeller

The Bureau of Mines performed laboratory research into the effects of a barium-based fuel additive (the "postflame" type) on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of types certifiable for use in underground mines. Test parameters consisted of additive concentration and engine loads, speed, and air intake restriction. DPM emissions, including condensed volatiles, were measured gravimetrically. Also measured were gaseous emissions including carbon monoxide, nitrogen oxides, and hydrocarbons. The fuel additive was effective, reducing DPM up to 75 pct, when used at a concentration of 0.09 wt pct (one-fourth of the concentration recommended by the manufacturer). The additive was most effective at the highest fuel-air ratios, reducing DPM from 400 mg/m3 for untreated fuel to 120 mg/m3. At light loads, 25 pct of full rated, no DPM reductions were measured. Based on these results, the additive is recommended for use in diesel fuel, at a concentration of 0.09 wt pct, to power underground mining equipment as long as certain conditions are met: that a beneficial DPM reduction is verified, that the minimum required quantity of additive is used, and that potential adverse effects such as increased nitrogen oxides are checked.

Jan 1, 1990

By Thomas L. McVay

Laboratory batch and pilot plant flotation tests were made to determine the feasibility of recovering commercial grade kyanite from a quartzite- kyanite rock from the Graves Mountain, Ga., deposit. Best results in laboratory and continuous tests were obtained using sodium carbonate for pH control, citric acid for quartz depression, and oleic acid as the kyanite collector. Over 80 percent of the kyanite was recovered in a concentrate analyzing 56.8 percent Al203 and 3.8 percent hydrochloric acid soluble Fe203. Subsequent treatment of the flotation concentrate by magnetic separation reduced the acid soluble Fe2O3 to 0.6 percent and increased the alumina content to 59.2 percent. Acid leaching of the concentrate gave a product analyzing 59.7 percent Al203 and about 0.1 percent Fe203. As a result of the beneficiation research, a commercial kyanite flotation plant was completed in September 1962 by private industry.

Jan 1, 1963

By D. J. Bauer

A primary amine extraction system was investigated for fractionating a cerium-group, lanthanide sulfate mixture. Addition of diethylenetriaminepenta-acetic acid (DTPA) to the amine extraction system resulted in separation factors as high as 5.4 for lanthanum-cerium, 8.0 for cerium-praseodymium, 3.7 for praseodymium-neodymium, and 7.0 for neodymium-samarium. In multistage studies on a cerium-free lanthanide mixture, 96 percent of the lanthanum was recovered with a purity of 95 percent.

Jan 1, 1968

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to devise a procedure for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 parts per million of W03). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten was recovered as a marketable iron-tungsten concentrate containing 44 percent tungstic oxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process-development unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By John E. Pahlman

The Bureau of Mines has conducted research on a dual leaching method that offers the potential for the economic recovery of the silver, as well as of the manganese, contained in some domestic manganiferous silver deposits. The method consists of an initial leach of manganese with aqueous sulfur dioxide (S02) followed first by a neutralization rinse, and then by a second leach with cyanide solution for the extraction of silver. Refractory silver in these ores was either (1) intimately associated with the manganese, (2) chemically resistant to cyanide leaching, or (3) rendered inaccessible to cyanide leach solution by the surrounding manganese mineralization. Less than 10 pct of the silver was extracted when minus 2.5-plus 1.3-cm ore pieces were leached directly with cyanide. However, extractions of 25 to 82 pct of the silver and 65 to 96 pet of the manganese were attained in laboratory column-leach tests using the dual leaching method on equivalent-sized ore pieces from seven domestic deposits.

Jan 1, 1987

By R. Barany

The heats of formation of anhydrous ferric sulfate and anhydrous indium sulfate were determined by solution calorimetry. At 298.15° K the heats of formation from the metal, rhombic sulfur, and oxygen were -615.6 ±O.7 kcal/mole for ferric sulfate and -649.6 ±O.6 kcal/mole for indium sulfate. Heats of decomposition at 298.15° K are given for the reaction that forms metal oxide, sulfur dioxide, and oxygen) and for the reaction that forms the metal oxide and sulfur trioxide.

Jan 1, 1965

By W. T. Abel

Laboratory tests were conducted with a closed, recycling system to evaluate the effectiveness of solid-in-gas suspensions as heat transport mediums. Micronized graphite in helium or nitrogen was circulated by a centrifugal compressor to determine the feasibility of the method and heat transfer capabilities of the mediums. Suspensions were circulated without plugging or eroding the compressor or piping. At low flowrates and light (0.1 to 0.2 volume-percent) graphite loadings, slightly less power was required to transport a given amount of heat with suspensions than with helium alone. Graphite deposition on the heat exchange surfaces of the cooler decreased the heat transfer effectiveness at higher solids concentration. Efforts to eliminate deposition are described.

Jan 1, 1963

By William H. King

Preliminary examination of the Virgin River manganese deposit was made by C. H. Johnson, Bureau of Mines engineer, in March 1941. During, April and May 8 trenches were dug, a 48-foot inclined shaft was sunk, and 719 linear feet of channel samples were cut. McKelvey and Wiese, of the Federal Geological Survey, completed mapping the deposit, including the entire area of overlying formations comprising the point of land between the outcrop and Lake Mead. The geologic maps, maps, and ore estimates resulting from these examinations formed the basis for a preliminary report by C. H. Johnson, who recommended further exploration by diamond drilling.

Jan 1, 1949

By William A. Beck

"The Piedmont Manganese Belt extends from Taliferro County, Georgia, 70 miles in a northeasterly direction through Greenwood County, South Carolina, and conforms with the trend of the Piedmont Province. The total area of the belt is reported to be about 1,000 square miles, and the maximum-width is about 24 miles.Manganese has been known to exist in the belt since 1845. M. Tuomey mentioned a deposit in the Edgefield district on Hard Labor Creek in South Carolina in a report on the geology of South Carolina published in 1848.Ore was first mined about the time of the first World War, when the Colley mine, near Lincolnton, Ga., was. Opened. The only operation in the area at present is that of the Abernathy & Kehaya Mining Co., at McCormick, S. C.The geographical position of the belt is from west longitude 82° 57’, north latitude 33° 39' to west longitude 82° 06', north latitude 34° 08'. The towns of Washington and Lincolnton, Ga., and McCormick and Greenwood, S. C., are in or near the belt.An exploratory project of the Bureau of Mines was started on the McCormick, S. C., deposit in April 1944, and trenching, test pitting, and hand-auger drilling-were done on a small scale until early in October 1944. (Fig. 1.) In November 1944 work was begun on a property 12 miles north of McCormick, known as Parsons Mountain, which is leased to M. H. McKnight by the United States Forest Service. From March 15 to March 24, 1945, work was done on the property of Mrs. H. B. Ross, which is known as the Morgan farm.The Abernathy & Kehaya manganese mine contains what is locally known as the Dorn gold mine; mineral rights on the property were owned by M. G. & J. J. Dorn, Inc."

Apr 1, 1946

By David E. Siskind

The Bureau of Mines recorded particle accelerations in the mine roof produced by three types of explosives in the Pilot Knob Pellet Co. mine, Pilot Knob, Mo. Examined were the effectiveness of cube root, square root, and two-thirds power scaling in grouping the underground blast vibration data, and the effects of mine geometry, rock type, explosive type, and charge size on blast vibration levels. A propagation law for this mine was determined. The scaling factor of the square root of the charge weight was developed from previous Bureau studies of vibrations from quarry blasts, and in under-ground blasting both square root and cube root scaling were found applicable for scaling particle vibration data. The vibrations from the Pilot Knob blasts were best grouped by a square-root scaling factor. The empirical propagation equation AW1/2 = 76,250 (R/W1/2)-2.61 where A is the peak acceleration in g's, W is the charge weight in pounds, and R is the distance from the blast in feet, may be used to describe vibration amplitudes from charges fired with zero delay caps or with a single cap at Pilot Knob. Statistically significant differences were found in the vibration levels generated by the different explosives. The Power Primer (75-percent weight-strength ammonia gelatin dynamite) produced levels of vibration of 1.7 to 2.4 times those of AN-FO and slurry explosives; the latter two are approximately equal.

Jan 1, 1973

By Paul C. Turner

The U.S. Bureau of Mines, through an Interagency Agreement with the U.S. Army Tank-Automotive Command (TACOM), has successfully developed a steel expendable pattern casting process (EPC) for the manufacture of armorplate. The new armor is lighter and more ballistically effective than conventional rolled homogeneous armor (RHA), and costs less. An applique armor spinoff from the program was field-tested during the Gulf War. The applique armor withstood direct impacts from enemy munitions without failure.

Jan 1, 2010

By Ralph H. Espach

The value of careful fractionation in the manufacture of petroleum products is recognized more and more by petroleum refiners. Recent studies have shown that the quality of the products depends largely on the type of fractionating equipment and on the care used in operating the equipment. For example Rue3 has shown that careful fractionation of pressure distillate will greatly reduce the amount of chemical treatment necessary to produce finished gasoline. The advantages of the combination of pipe still and bubble tower in obtaining good fractionation are well recognized in the petroleum industry. However, the equipment designed in the past has in general been much too large for convenient laboratory use. The present paper describes a continuous-distillation apparatus for the laboratory study of fractionation. This apparatus has given very satisfactory results in the study of different crude oils and petroleum products. A discussion of the theory and action of bubble towers has not been given, as this subject has been discussed previously by Cooke and Rue4. It is believed that the distillation curves of the products obtained from this apparatus show clearly its capabilities.

Jan 1, 1928

By A. R. Taylor Jr.

The heat capacities of a-quartz form beryllium fluoride were measured at approximately 3° intervals from 8° to 300° K., using an adiabatic calorimeter. At 298.15° K the heat capacity and entropy were 12.39 cal/deg mole and 12.75 ±0.04 eu respectively. Enthalpy measurements were made with an ice calorimeter at approximately 30° intervals on the quartz and glassy forms of beryllium fluoride between 300° and 1,200° K. A melting point of 825° K and an 0,-8 type transition at 500° K with a heat effect of 75 ca1/mole were deter-mined from the enthalpy data for the quartz-type sample. Beryllium fluoride glass crystallized spontaneously into the quartz modification at 500° K. The heat of the reaction BeF2 (a-quartz) .... BeF2 (glass) was found to be 1,125 ±16 cal/mole at 298° K by solution calorimetry. This value, when corrected to 273° K, was used to correct for the heat absorbed by the formation of glassy BeF2 when the sample was dropped into the ice calorimeter from temperatures above the melting point. Using corrected enthalpy measurements, the heat of fusion was determined to be 1.13 kcal/mole at 825° K.

Jan 1, 1965

By D. P. Desmond

The U.S. Bureau of Mines investigated leaching automobile catalysts with sodium cyanide (NaCN) solutions at high temperatures to recover platinum-group metals (PGM). The feed was virgin monolith rejects, used monolith, and used pellet catalysts. Leaching with a 5-pct NaCN solution for 1 h at 160° C dissolved over 97 pct of the PGM in the virgin monolith, over 85 pct of the PGM in the used monolith, and over 90 pct of the PGM in the used pellet catalyst. Over 99.8 pct of the dissolved PGM was recovered as a precipitate by heating the solution to 250° C for 1 h in an autoclave. The cyanide complexes were decomposed, and free cyanide was destroyed.

Jan 1, 2010

By W. D. Mcmillan

Soapstone is the term applied to an impure, massive, soft rock with a greasy feel. It is of variable composition, consisting chiefly, however, of talc, tremolite, and chlorite. Although limited quantities of soapstone are used as building material, in fireplaces, and in the manufacture of laundry tubs, sinks, laboratory-table tops, and-oven and furnace blocks, the principal part of the production is ground for use in roofing paper, insecticides, and as a filler in asphaltic paints.

Jan 1, 1949

By Martin Hertzberg

The concept of limit burning velocities, formulated in an earlier Bureau of Mines report (RI 8127), is applied to the problem of flame propagation through tubes of finite size. The limit burning velocity for conductive-convective wall-loss quenching (process b) is (Su)b = [aPe,] where the proper choice of critical Peclet constant, Pe, is determined mainly by the ratio of contact-perimeter loss area to flame-zone cross sectional area. This ratio of loss area to propagation area relates to the shape of the flame front and its control by buoyancy and by boundary conditions. The comparison of (Su)b with previously defined limit velocities for systems mixed by natural convection allows one to assess the influence of tube dimensions and boundary constraints on the "true" or earthly limits for the three directions of propagation. The flame quenching caused by inert powders is shown to be similarly described in terms of a limit burning velocity, (Su)?b. The tube's surface-to-volume ratio (~1/ro) is simply replaced by the powder's surface area per unit volume of the flammable mixture. Thermal loss quenching by these "internal walls" occurs at a critical Peclet constant somewhat higher than that observed for tubes, and the problem is complicated by the finite heat capacities of the powders and particle lag effects in the flame front.

Jan 1, 1980