Search Documents

By T. E. Gray

This report describes the preparation characteristics of the signifi¬cant coalbeds in Preston County, W. Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 2 million tons of coal was produced in Preston County, W. Va. in 190, none of which was cleaned mechanically. Estimates as of January 1, 1959, indicate that more than 3 billion tons of coal remained in the county in beds 12 inches or more thick. The Bakerstown, Mahoning, Upper Freeport, and Upper Kittanning beds were selected by the Bureau of Mines for study based on current production and estimated minable reserves. Sample locations were selected after study of the literature, conferences with mining engineers and mining company offi¬cials in the field, and examination of available sites. Four samples were collected from the Bakerstown and Upper Freeport beds and one each from the Mahoning and Upper Kittanning beds.

Jan 1, 1961

By Cleo Griffith Rall, D. B. Taliaferro

The method for determining oil and water saturations described herein has been used successfully for several years in the core laboratories of the Bureau of Mines. The apparatus constructed according to the original specifications has proved very satisfactory; in fact, it has been widely adopted by core laboratories throughout the petroleum industry. The writers have found that the method gives reproducible results, the degree of accuracy depending largely on the attention to details given by the operator. The relative importance of these details of procedure and the design of the apparatus are discussed in this report. In September 1940, the Bureau of Mines published a report describing a method used in its laboratories for the determination of the water content of oil-field cores. The procedure was essentially the same as that adopted by the American Society for Testing Materials for the determination of the water content of petroleum products, although the apparatus and technique were altered slightly to increase the precision of the method and to adapt it to the characteristics of the material to be tested. The report also contained a description of the method used at that time in the Bureau’s core laboratories for measuring the oil content of a core, utilizing the sample on which the water-saturation determination had been made. The procedure involved the transfer of the weighed sample, from which the water had been distilled and measured, to a Soxhlet extractor and the removal of the remaining oil by means of a suitable solvent. Soon after the report was published, the water-determination apparatus described therein was modified so that both the oil and water contents of a core sample could be determined simultaneously. This method, which has been described by Yuster, is now widely used throughout the industry.

Dec 1, 1946

By Paul M. Tyler

The colony of French Guiana ( or Cayenne ) is administered by a governor , assisted by a privy council of five members . A council - general of 16 members is elected by French citizens resident in Guiana, and the colony is represented 3 in the French parliament by one deputy . The area is about 34,740 square miles . French Guiana is the largest gold producer of the French colonies , producing nearly $ 1,000,000 worth annually . Considerable prospecting has been done on the bauxite deposits , which are extensive . Copper , iron , lead , and 4 mercury deposits are also reported . In 1931 , 10,000 prospectors for gold were reported as working . The French Government is taking an active interest and has sent a committee of mining experts to explore the region ; no permits are to be issued to individual prospectors while the committee is in the colony . Plans for development of mining industry include consideration of 4,500 convicts and 2,500 natives already in the colony and available for labor .

Apr 1, 1933

By Ronald D. Hill, Elmore C. Grim

Coal-haul and mine access roads are defined as any road constructed, improved or used by the operator (except public roads) that ends at the pit or bench. These roads constitute approximately 10% of the total area directly disturbed by the surface mining operation(l). In some cases, the land disturbed by haul roads exceeds the area included in the mining operation. Studies (2 and 3) of the U. S. Forest Service in eastern Kentucky show that typical contour mining roads exhibit poor alignment, excessive grades, insufficient strength and durability, and poor drainage. Mine roads in other Appalachian- States, particularly where contour mining is practiced, appear much the same as those in Kentucky. Access roads(4) were also found to be a large source of sediment. It is possible that of the sediment that finds its way into the streams as much (or even more) originates from the haul roads as from the mining operation. Most roads are built as cheaply as possible, and good road-building design and practice are ignored. Maintenance schedules are generally inadequate, and upon completion of mining, haul roads are usually abandoned, with little or no attempt made to bed them down(5 ) . Such roads deteriorate very rapidly (Figure 68). Area mining, which is practiced in flat to gently rolling terrain, presents fewer haul road related environmental problems. These roads through necessity are generally well engineered because of the heavy equipment using them, such as 240 ton (217 metric ton) haul trucks. They must have wide beds, good alignment, and adequate drainage to permit coal haulers to run at top speed during all seasons of the year. Excessive dust can be a public nuisance and a driving hazard, and it is hard on equipment. Calcium chloride and sodium chloride have proven to be effective materials for controlling dust. Two applications during the summer when the ground surface is moist at the rate of 1/2 pound per square yard (.26 kilograms per square meter) (3 1 have been suggested. Th4 most common procedure is to keep the roads wet by using water trucks. Sediment that reaches the streams can be traced to one or more of the following five basic phases of haul-road life:

Jan 1, 1974

By O. C. Blade

This report is one of a series made by the Bureau of Mines under a cooperative agreement with the American Petroleum Institute on the characteristics of commercial aviation gasolines. The series of Surveys is a continuation of like work conducted under aimil.ar cooperative agreements with the Coordinating Research Council, Inc. by the National. Bureau of Standards from 1940 through 1946 and by the Bureau of Mines from 1947 through 1949. A completed list of the series of surveys is given at the end of this paper.

Jan 1, 1951

By Frank J. Wiebelt, Spangler Hicker

The Iron Mountain investigations were part of a comprehensive program for making a national inventory of raw materials used in the production of steel. A tentative program of core drilling by the Bureau of Mines was set up for exploration of more promising iron deposits. Iron Mountain was selected as worthy of investigation because it could serve as a potential source of ore for the war-created steel plant at Fontana, Calif. The deposits were reported on by an engineer in October 1943. The purpose of the project was to determine the lateral and vertical extent of ore bodies and to obtain accurate material data on them.

Apr 1, 1948

By Jack E. Fraley

Because of their noncombustibility, silicate and magnesium oxycements are desirable for sealing shale in underground coal mines. In this Bureau of Mines investigation, cement samples were cured and tested (nonstandard tests) for submersion to note resistance to dissolution (breaking into parts), which is an important property for a coating. Nonappreciable dissolution during 1 week of submersion was set for passing the test. Over half of the coatings passed the test.

Jan 1, 1977

By W. D. Mcmillan

The Dempsey tract in Washington County, Mo., had a small production of lead-zinc ore from shallow workings. Old dumps from early-day lead mining contain about 25,000 tons of ore averaging about 3 percent combined zinc and lead. Because of the urgent war requirements for lead and zinc, the Dempsey property was examined by Otto Ruhl, formerly an engineer of the Bureau of Mines in August 1942 and selected for further investigation by churn drilling twenty holes totaling 1,309 feet were bored in the fall of 1943. The results of the work are presented in this paper.

Jan 1, 1948

By V. J. Lynch, A. L. Peyton

"INTRODUCTION AND SUMMARYThe Brewer mine, near Jefferson, Chesterfield County, S.C., was originally operated as a gold mines as late as 1890 this mine was reported to have been one of the large gold producers in the southeast,Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered by Pardee and Parks. 3/ of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.During the 1940's the Chemical Engineering Branch of the Tennessee Valley Authority and the Electrotecbnical Laboratory of the Bureau of Mines at Norris, Tenn., investigated topaz from the Brewer mine to determine the possibilities of its use as mullite and for the production of calcium fluoride.From July 1950 through. April 1951 the Bureau of Mines conducted a diamond-drilling project at the Brewer mine to determine the grade and extent of the topaz deposits. Ten diamond-drill holes, totaling 2,344 feet, were completed, and 231 analyses of core samples were made during the course of the project.This report presents factual data relating only to the diamond-drilling project, The placer deposits on the Brewer property were previously investigated by the Federal Geological Survey 4/."

Aug 1, 1953

By R. A. Guereco

Accurate measurements of physical dimensions of a section of stainless steel capillary tubing are presented and used to develop two final working equations for an absolute gas viscosimeter. The effects of pressure and temperature on these dimensions are considered. The internal surface finish and nonuniformity of the capillary bore are discussed, as well as entrance, kinetic energy, gas slippage, and gas compressibility correction factors.

Jan 1, 1967

By R. L. Brown, H. G. Berger, E. F. Pohlman

"The Bureau of Mines in cooperation with the American Gas Association investigating the relation of properties of gas oils to the gum-forming properties of carbureted water gas. The present report deals with the effects of operating practice on the composition of the light oils from carbureted water gas. A general outline of the gummy meter problem has been presented in a previous paper.*Carbureted water gas is a mixture roughly of 80 per cent water gas by volume and 20 per cent oil gas. The latter, though small in relative volume, supplies more than half of the heating value of the gas under the present-day standard. Therefore, it is logical that the oil used in the carbureting process and the operating practices involved should be subjected to scientific study. Many investigations***** bearing on the aspects considered in this paper have been carried out in the past."

Oct 1, 1923

By W. C. Holliman

This report on the characteristics of commercial aviation gasolines presents compilations of inspection test data furnished on their products by manufacturers of commercial grades of aviation gasoline, and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data and physical samples for the survey were submitted by 15 manufacturers on 18 grade 80, 21 grade 91/98, 22 grade 100/130, and 10 grade 115/145 aviation fuels.

Jan 1, 1948

By A. L. Engel

This investigation was undertaken to assess the feasibility of processing an extensive deposit of iron ore near Palisades, Eureka County, Nev., previously penalized for high phosphorus content. The experiments described indicate a satisfactory accomplishment of objective. Chemical treatment will permit a high-phosphorus iron ore to be used. Leaching with acid solution effectively lowers the phosphorus content with a [gligible] loss of iron. The use of hydrochloric acid is preferred because [ ] does not contaminate the ore and the cost is lower. Minus-1/2-inch ore was satisfactorily leached in 24 hours, minus-1/4-inch ore, in 8 hours, and minus-10-mesh ore, in 3 hours. About 40 pounds of acid per ton of ore was consumed in each instance.

Jan 1, 1959

By Agnes Y. Lee

The Bureau of Mines has developed an effective hydrometallurgical method to recover high-purity Pb metal and elemental S from concentrates. This low-temperature process eliminates S gases and Pb emissions, in contrast to the current high-temperature smelting technology. The method consists of (1) oxidative leaching with H202, Pb02, and waste fluosilicic acid at 95° C to produce a solution of PbSiF6 and a residue containing elemental S, (2) electrowinning the PbSiF6 solution at 35° C to produce 99.99 pct Pb metal and H2SiF6, and (3) solvent extraction to recover S, leaving a residue containing Cu, Ag, and other metal values. Spent electrolyte was recycled repeatedly, with impurity buildup controlled by controlling the leach parameters.

Jan 1, 1986

By James Noll

Total carbon (TC) is sometimes used to measure or characterize diesel particulate matter (DPM) in occupational settings such as underground mines. DPM samples are collected on quartz fiber filters. When using quartz fiber ?lters, adsorption of gas phase organic carbon (OC) has been reported, causing a positive bias in the particulate TC results (adsorption artifact). Most of the data on the sampling artifacts and corrections apply to environmental air sampling, where samples are collected at a much higher filter face velocity and the OC concentrations are generally much lower relative to occupational sampling. In this study, we investigated the effects of adsorption artifact on samples from occupational settings. Samples were collected with and without denuders to determine the amount of gas phase OC collected and the accuracy of certain corrections. In underground stone mines, the adsorption artifact was found to positively bias the particulate TC by greater than 20% for filter loadings below 25 µg/cm2 TC (8-h time weighted average) 262 µg/m3). The tandem ?lter correction reduced the effect of the artifact, as high as 60% of the TC value, to less than 11% for laboratory data. It also significantly reduced the effect of the artifact obtained for field samples.

Jan 1, 2008

By Charles Vaught

The U.S. Bureau of Mines evaluated the self-contained self-rescuer (SCSR) donning proficiency of 243 miners. These workers were from eight underground coal mines in the eastern United States. The objectives of the study were (1) to gather information on skill levels, since all miners in the study had prior instruction and opportunity to practice donning the apparatus, and (2) to summarize a quality control procedure useful in conducting periodic evaluations of donning proficiency. The sampling procedure used proved to be both reasonable and efficient in gathering information on training effectiveness_ It also provided a good statistical base for making informed site-specific decisions regarding SCSR training needs. Results from the observed samples at each of the eight mines indicate a wide variability across sites. The rate at which miners failed to isolate their lungs varied from 33 to 40.0 pct. Concomitantly, proficiency rates (miners either performing adequately or demonstrating a perfect 3+3 sequence) ranged from 13.3 to 63.3 pct.

Jan 1, 1991

By J. Sammarco

Proper illumination is critical to a miner?s ability to detect hazards in underground mines. Moving hazards are often located in the miner?s peripheral field-of-view, while slip/trip/ fall hazards are often located in the forward field-of-view. The objective of the research described in this paper was to determine if light-emitting diodes (LEDs) improve visual performance as compared to traditional incandescent (INC) cap lamps. The research presented focuses on comparative studies of a National Institute for Occupational Safety and Health (NIOSH) prototype LED, a commercial LED and an INC camp lamp. Thirty subjects participated in these studies, with ten subjects in each of the following age groups: 18 to 25 years, 40 to 50 years and 51+ years old. Visual per­formance was quantified by the subjects? speed and accuracy in detecting hazards, while visual performance for disability glare was quantified by the use of contrast sensitivity tests. Results suggest that LEDs with a visible spectrum containing a higher concentration of the shorter wavelengths can enable visual performance improvements with respect to disability glare, the detection of moving hazards in the peripheral field-of-view and the detection of floor hazards in the forward field-of-view. The NIOSH prototype LED cap lamp provided the best visual performance improvements for the older age groups in every test.

Jan 1, 2009

By Charles Prasky

The Bureau of Mines investigated the conversion of nonmagnetic iron minerals to magnetic form through reduction Toasting operations. The primary objective was to obtain a concentrate that could be used as a direct shipping material for blast furnace consumption. Crude iron materials from the Steep Rock Lakes, Ontario, area were prepared into a blend of 8 parts siliceous ore, 3 parts pyritic ore, and 1 part tailings. Experimental work included laboratory reduction roasting tests, two continuous 10-day campaigns, and one 12-hour test all in a 34-inch by 36¬-foot rotary kiln. The objective of the project was achieved in producing an iron concentrate containing about 66 percent iron with over 90 percent iron recovery. Desirable operating conditions were developed in the kiln but optimum process variables were not completely established.

Jan 1, 1969

By Albert L. Toenges, Henry E. Dekay, James N. Scudder

Support of the immediate roof in coal mines is essential for their safe operation, and timbers are the most common means of support. Their effectiveness depends upon their resistance to decay. The theory has been advanced by some mine operators that rock dust, which is applied to ccal-mine workings to prevent propagation of explosions, accelerates the decay of mine timbers. As the results of part 1 of this study were inconclusive, the study was continued. Its principal objectives are: 1. To determine the effect of rock dusting upon decay of mine timber. 2. To compare the extent of decay of timbers in two mines in which underground conditions are similar. 3. To determine the loss in strength of the timbers after exposure to mine atmosphere. The studies were carried on in the Crucible mine of the Crucible Fuel Co. where the first part of this study was made, and in the Isabella mine of the Weirton Coal Co. The mines are on the Monongehela River and are adjacent.

May 1, 1943

By David E. Morse

Burundi, a small central African republic located between Tanzania and Zaire, remained essentially a nation of small family farms in 1978-79 with approximately 95% of the population engaged in subsistance agriculture. Coffee and tea continued as the nation's major export commodities. Mineral exports, small tonnages of cassiterite, wolframite and bastnasite, accounted for an estimated 3% of total exports in 1978 and 2% in 1979, or $2 million2 in both years. Burundi's major mineral imports in 1978-79 were cement, iron and steel, and refined petroleum products. Abnormal weather conditions, a drop in world coffee prices in 1978, and the conflict in neighboring Tanzania and Uganda in late 1978 and early 1979 combined to re-strict economic growth in Burundi during 1978-79. The gross domestic product (GDP) posted a gain of 6.7% in real terms for 1978 and an estimated 2.5% for 1979 which was significantly less than the 13.7% recorded in 1977, a time of high world coffee prices. The manufacturing and construction sectors were hard hit in 1979 by the conflict between Burundi's eastern neighbors because of transport disruptions which made building materials and manufacturing inputs almost unobtainable.

Jan 1, 1981