Search Documents

By M. H. Kline, Wing G. Agnew

"INTRODUCTION The Yancey-Crawford tract, located 1-1/2 nines east of Yancey station on the Norfolk & Western Railway in Rockingham County, Va. was from 1917 to 1941 considered an unusually promising manganese prospect. Because of the favorable geologic formations and because of the common occurrence of manganese in the district and Virginia's large production of these minerals from this area, geological report 3/ have listed this tract as the No. 1 prospect in the State. During World War I, extensive geologic studies were made to locate manganese deposits similar to those exploited at the Crimera mine near Waynesboro to alleviate this mineral shortage during the existing emergency.In September 1941 the Bureau of Mines started exploratory drilling on the tract in an effort to discover and block out reserves of manganese minerals as authorized by the 76th Congress under the Strategic Materials Act. After five drill holes wore sunk, the project was terminated October 1941."

Apr 1, 1948

By M. Orchin

THIS PAPER is concerned with two aspects of the behavior of coal: (1) Dispersion by solvents atmospheric pressure and high temperature and (2) the destruction and regeneration of the coking properties of coal. Several pure polycyclic compounds and a coal-tar fraction were found to extract 95 percent of the organic material of a bituminous coal. About 20 percent of the extract was soluble in benzene, and this fraction contained the ?coking principle? of the coal. From an extensive chemical spectroscopic, and x-ray study of the benzene-soluble material, some conclusions could be drawn concerning the composition and structure of this fraction of coal. A possible commercial application of the extraction technique is in the preparation of low-ash carbonaceous material for the manufacture of electrode carbon.

Jan 1, 1951

By E. B. Kester

A study of the composition of the corresponding fractions of a primary and a high-temperature tar was undertaken to throw light on the net results of the pyrolysis of the primary products of coal decomposition in high-temperature coking practice, with reference both to total quantities of the chemically similar constituents and to their distribution throughout the boiling range. No exactly parallel investigations are on-record. The distribution of substances in high-temperature tars, however, is fairly well understood. Such tars are more or less similar, for they consist of the more stable phenols, aromatic and olefinic compounds resulting from the pyrolytic decomposition of a wide variety of primary tar constituents. For example, from a typical distillation curve for high-temperature tar phenols it may be seen that the greatest portion of the phenols distills between 180° and 220° C., a fairly narrow range. Low-temperature tars, on the other hand, are more complex, and hence exhibit dissimilarities from one to the next. Edwards, who has made a study of the acids, bases, and neutral oil of four low-temperature tar distillates, shows that the bases and neutral oil are evenly distributed among the fractions but that the concentration of the acids is greatest in the 200° to 230° fraction. Morgan and Soule find that in tar from the "Carbocoal" process, the 237° to 281° fraction has the highest acid content, whereas Davis and Parry find the 200° to 225° fraction of Freeport tar richest in phenols. Previous investigators have noted the following differences between primary and high-temperature tar: In the latter, naphthalene and anthracene occur in large quantities, the paraffins and naphthenes are negligible, the percentage of higher phenols is much lower than in primary tar, and the lower and more stable aromatic hydrocarbons have increased. In an endeavor to reconcile the change undergone when a primary is converted into a secondary tar, the writers have been unable to find references dealing with the extent of change which any one of the constituents of primary tar may undergo when subjected to secondary heating effects in the presence of other components, and the amount of the more stable compounds that may be expected from a given starting material.

Jan 1, 1932

By F. Garacia, J. Cervik

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of a discharge pipe. These measurements are erroneous and tend to be high by as much as 30 pct. The Bureau of Mines deter- mined method factors (correction factors) for anemometer measurements taken in this manner. Method factors for 4-, 6-, and 8-in (10.2-, 15.2-, and 20.3-cm) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By J. S. Kennedy, R. G. Omeara

Beryllium is a strategic metal of ever-increasing peacetime importance because of the unusual properties of beryllium-copper alloys. These unusual characteristics are the combination of high strength and hardness, high fatigue resistance, and high wear resistance in alloys that have the corrosion resistance of copper. The principal industrial source of beryllium is the mineral beryl, a beryllium-aluminum silicate that occurs in pegmatites associated with quartz, feldspar, mica, and smaller amounts of various accessory minerals. The beryl is usually recovered in processing the pegmatites for the recovery of some of the other mineral constituents. Pegmatite deposits are found in various parts of the United States, but those in the Black Hills of South Dakota are the source of most of domestic production. The beryl marketed from the South Dakota pegmatite deposits occurs as coarse crystals, which are obtained by hand sorting. These pegmatites also contain other valuable minerals.

Jan 1, 1948

By Richard F. Hewlett

Numerous populations of assays have been simulated for a range of assay values representative of low-grade mineral deposits to facilitate the study of problems encountered in evaluating these deposits. Analysis of these simulated populations of assays (obtained by using statistical probability models for the simulation) makes possible the quantification of the effects of (1) various composite assay intervals, (2) ore reserve computational methods, (3) uneven assay intervals, and (4) various cutoff grades on both the precision and the accuracy of the estimated average grade and tonnage of ore.

Jan 1, 1964

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1954 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 101 samples of aviation gasoline. Data also are given for 30 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers I 1954 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 19 manufacturers of aviation gasolines and of 15 producers of aviation jet fuels are represented.

Jan 1, 1955

1. PURPOSE The Temporary Face Support System (TFSS) consisting of beams, posts and carrying-emplacing equipment was developed to provide temporary supports between the working face and the permanent roof supports. 2. GENERAL DESCRIPTION The system consists of: ? A Beam And Post Carrier And Deployer (BAPCAD), a self-propelled machine that carries as well as emplaces the beam-and-post sets. ? Lightweight mechanically self-deploying posts designed to safely support a load of 10,000 pounds each. ? Lightweight constant strength beams (bars) capable of sustaining an approximate equally distributed load of 8500 pounds. Note. All referenced figures and drawings are found at the back of this manual.

Jan 1, 1980

By Joseph Berman

The wolframite mineral series was studied to determine the effect of the FeO - MnO ratio on unit cell symmetry and thermal stability. This work was undertaken to evaluate the analytical procedures now in use for wolframite in scheelite and to aid in the development of improved methods of analysis. Wolframite grains were hand-picked, crushed, and screened; impurities were removed by selective magnetic separations using a Frantz isodynamic separator. The samples were further checked by optical spectroscopic and microscopic examination.

Jan 1, 1957

By T. T. Read

"Employee representation in the management of large mining enterprises was first introduced in organized form, by the Colorado Fuel and Iron Co. in 1915. Within the past few years a number of the larger mining enterprises have introduced similar systems and there is growing interest in the subject. This will be stimulated by the final report of the President's Second Industrial Conference, in which the following statement occurs:""The conference finds that joint organization of management and employees where undertaken with sincerity and good will has a record of success. The general principles governing such organizations are stated at length under the title 'Employee Representation. It is not a field for legislation, because the form which employee representation should take may vary in every plant. The conference, therefore, does not direct this recommendation to legislators but to managers and employees.""If the joint organization of management and employees in the plant or industry fails to reach a collective agreement, or if without such joint organization, disputes arise which are not settled by existing agencies, then the conference proposes a system of settlement close at hand and under Government encouragement, and a minimum of regulation. The entrance of the Government into these problems should be to stimulate further cooperation."""

Mar 1, 1920

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests.

Jan 1, 1957

By Jeffrey H. Welsh

The Bureau of Mines studied the use of computerized, continuous, remote monitoring systems for safety from power system faults in underground coal mines. In this report the need to improve protection against power system faults is documented, and types of faults are identified. The relationship between mine safety regulations and computerized, continuous, remote monitoring is analyzed.

Jan 1, 1983

By H. R. Babitzke, H. Kato, M. D. Carver

A number of columbium and tantalum alloys were investigated to determine their suitability for use at elevated temperatures . Columbium-vanadium , tantalum-vanadium , and tantalum-hafnium alloys , and also columbium- 10 wt pct titanium alloys modified with additions of 0.1 to 2 mole pct ZrO2 , TiO2 , ZrB₂ , TiB , ZrC, or TiC were prepared and examined . Workability , tensile properties , and oxidation resistance were tested . Of the columbium alloys studied , the columbium- 12 at . pct vanadium exhibited the best properties ; it compared closely with the columbium- 10 at . pct vanadium alloy studied in a previous investigation.

Jan 1, 1964

By A. L. Engel

This report is a compilation of results of preliminary concentration tests of nine manganese-ore samples in 1953-1954. Three samples were from Nevada and the other six from California. These samples represent marginal or low-grade ores from deposits that have been mined selectively in the past. The present interest lies chiefly in the possibilities of concentration of the remaining low-grade ores for economical exploitation. The treatment methods included gravity concentration and flotation in most cases. Results were sometimes unsatisfactory, particularly when the ore was too fine grained for liberation of the minerals within economical grinding range. The contaminating gangue minerals, such as quartz and iron oxides, were locked with the manganese to an extent that prevented separation of high-grade concentrates with satisfactory recovery. In cases where fairly good concentrates were made, it was at the expense of recovery, a condition typical of low-grade ores.

Jan 1, 1955

By J. D. Davis

On May 15, 1936, Congress authorized the Bureau of Mines to conduct certain studies, experiments, and investigations of subbituminous coal and lignite .4/ Appropriations were made in July 1937, and since that date an active investigation has been underway to complete the provisions of the act. Part of the investigation has included a comprehensive survey of the known properties of the lower-rank non-coking coals, and provisions were made to obtain more data on certain varieties. In line with this plan, a typically subbituminous coal was selected for an extended series o tests in the standard Bureau of Mines-American Gas Association unit,5/ at the Central Experiment Station. This particular noncaking coal was the first one of its rank that ha& been tested in the apparatus; for this reason the results are of particular interest because the testing apparatus was originally designed for use in studying the coke- and gas-making properties of coking coals. The test as described below has been developed by the Bureau of Mines since 1927 through a cooperative agreement with the American Gas Association.6/ Ninety to 180 pounds of coal is heated in a circular retort, 13 to 18 inches in diameter, at wall. temperatures ranging from 540°C. to 1,110°C. in 100°C. steps. All products axe collected and measured; their physical and chemical properties axe then carefully determined to ascertain the gas- and coke-making properties of the coal.

Jan 1, 1939

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Cu and Zn-0.12 pct Ti-Cu alloys with various copper additions to 1.25 pct. The alloys were rolled cold and at various hot-rolling temperatures to reductions as high as 92 pct after breakdown rolling. The properties are extremely sensitive to various combinations of composition, rolling temperature, and rolling reduction, Zn-Cu alloys can develop good creep resistance, but they are inferior in that respect to Zn-Ti-Cu alloys. For alloys either with or without the titanium addition, cold-rolling results in recrystallization of the matrix and rejection of copper from solution, causing poor hardness, tensile, and creep properties, but high ductility. Peak tensile strengths develop when the alloys are rolled in the range 320° to 400° F, Best creep resistance for Zn-Cu alloys requires higher rolling temperatures when copper content is increased. Creep resistance is best for Zn-Ti-Cu alloys with about 0.75 to 1.0 pct CU rolled near 480° F. Some copper is soluble in the TiZn15 phase, which forms into "stringers" during rolling. The possible contributions to creep behavior of factors such as distribution of second-phase particles, grain size, and preferred orientation are discussed.

Jan 1, 1970

By L. F. Heising

The Bureau of Mines evaluated 191 composites from the central Mesabi Range, Minn., chiefly by reductive roasting and magnetic separation. After reductive roasting and magnetic separation at minus 325 mesh, 28 composites produced concentrates that contained an average of 66.0 percent iron with less than 10 percent silica. Recovery of contained iron was over 90 percent. Natural magnetic material in excess of 5 percent was present in 142 composites. Trial flotation tests were used to evaluate three samples unresponsive to reductive roasting and magnetic separation procedures, and satisfactory concentrates having low silica contents (averaging 6.6 percent) were achieved.

Jan 1, 1965

Although alternating-current (a.-c.) power systems and equipment have been used in coal mining for many years, most mines in the United States are powered mainly by direct current (d.-c.). There are several logical reasons for this, but the use of d.-c, equipment is, in most instances, a direct outgrowth of the original practice of using such power for haulage systems. For traction equipment such as the electric trolley locomotive the d.-c. motor has ideal operating characteristics, and thus it has been widely used for haulage locomotive service. The first efforts at electrification of coal mines started with the haulage system and from there branched out to include the many types of electrically powered mining machinery used in the industry today.

Jan 1, 1960

By E. B. Kester

A study of the composition of the corresponding fractions of a primary and a high- temperature tar was undertaken to throw light on the net results of the pyrolysis of the primary products of coal decomposition in high-temperature coking practice, with reference both to total quantities of the chemically similar constituents and to their distribution throughout the boiling range. No exactly parallel investigations are on record. The distribution of substances in high-temperature tars, however, is fairly well understood. Such tars are more or less similar, for they consist of the more stable phenols, aromatic and olefinic compounds resulting from the pyrolytic decomposition of a wide variety of primary tar constituents. For example, from a typical distillation curve for high-temperature tar phenols4 it may be seen that the greatest portion of the phenols distills between 180° and 220° C., a fairly narrow range.

Jan 1, 1932

By Laurance L. Oden

Titanium-enriched smelter slag produced commercially by Quebec Iron and Titanium Corp., Sorel, Quebec, was evaluated as feed material for a process developed by the Bureau of Mines to prepare rutile. Glass-forming agents including P205, B203, and two binary mixtures were added individually to the as-received and preoxidized smelter slag, and the nonferrous tramp oxides were effectively partitioned into the resulting noncrystalline phase. Iron in the ferrous oxidation state was moderately soluble in the glass of reduced specimens but less soluble under oxidizing conditions. The solubility of iron oxide in phosphate glass exceeded the solubility of iron oxide in borate glass. Effective conversion of titanium oxide to rutile was not achieved in the high-iron commercial smelter slag, and 20 to 30 pct of the titanium remained as pseudobrookite, a mixed iron-titanium oxide.

Jan 1, 1973