Search Documents

By Richard A. Watson

A frequency-shift keying (FSK) modulator-demodulator (modem) network has been devised for the Bureau of Mines mine-monitoring systems. This network permits an unlimited number of remote stations to communicate with one central station over the same pair of wires. The network operates at a speed of 4,800 Bd at distances up to 5 miles. This report describes the development and operation of the modems. The theory of operation, schematic diagrams, and printed circuit board layouts are provided. Although the modems were built for a specific application, a more general use is discussed whereby the network would operate with a typical serial channel format.

Jan 1, 1985

By Arthur H. Redfield

The expansion of city street laving which characterized the ten years ended December 31, 1929, according to a survey of 201 representative cities, made by the bureau of Mines, reached it climax in 1927, with decreases reported for 1928 and 1929. The upward trend, followed by a decline, was general in cities of all sizes included in this study, but was most pronounced in cities of 40,000 to 100,600 inhabitant and in the Northeastern, Southeastern, and Southwestern States. In the North-Central States the trend of paving; was downward from 1925 to 1929; in the Pacific, and Rocky Mountain States it was generally upward. Over the nation as a whole, bituminous types of paving continued to lead, furnishing two-thirds of the total street pavement laid in the 201 cities from 1925 to 1929. The actual yardage of bituminous pavement laid in these cities, however, was 3.8 per cent less in 1923-than in 1925, and the ratio of bituminous pavement to the total pavement t dropped from 70.4 per cent in 1925 to 62.1 per cent in 1928, rising to 65.1 per cent in 1929. The area paved with Portland-cement concrete amounted to only one-fourth of the total, pavement laid in these cities from 1925. to 1923., but the yardage of Portland-cement pavement increased by half during the period, and its share in the total pavement grew from 19.3 per cent in 1925 to 30.0 per cent in 1928, declining to 29.5 per cent in 1929. Brick, block, and stone pavements, which constituted the remaining one-twelfth of the total pavement laid in the 201 cities, decreased one-third in yardage, and declined in relative importance from 10.3 per cent in 1925 to 6.6 per cent in 1929.

Jan 1, 1931

By Serge Rudchenko

A study to determine the potential use of retaining structures in open pit backfilling. Research and review of the open pit mine environment, mine waste disposal, and past and current use of retaining structures. A development of specific structures, the culvert/ tunnel concept, and an anchor block retaining concept. The cost benefit of retaining structures used for in-pit backfilled waste.

Jan 1, 1981

By J. Fletcher Smoak

Consumption of abrasive materials in the United States decreased 23% in value from that of 1981 to $262 million, of which 53% was manufactured abrasive, 39% was industrial diamond (natural and synthetic), and 8% was natural abrasive. Production of natural abrasives, excluding industrial diamond, appeared to be stable when compared with that of 1981. Production of tripoli, a porous siliceous rock, increased slightly after decreasing steadily over the three previous years. The production increase of garnet, an abundant iron-aluminum silicate, was attributed to increased output from one plant that had completed an expansion program in late

Jan 1, 1983

By V. B. Royer, C. H. Harty

"MANGANESE-SILOCON ALLOYS AS DEOXIDIZERSThe basic open-hearth process for steel mining requires large amounts of oxidized iron for oxidation of the elements carbon, silicon, manganese, and phosphorus which are to be removed from the metal. Some of this oxidized iron (FeO) dissolves in the metal during the refining process, Subsequent to the elimination of the elements named, a considerable amount of dissolved iron oxide must be removed before the metal may be cast into ingot form. The elements generally used, for iron oxide removal, or deoxidation, are silicon, manganese, and aluminum. Silicon and manganese are always alloyed with iron, either singly or in combinations of various compositions. Aluminum generally is used in a commercially pure state and sometimes in complex alloys. A double deoxidizer of manganese and silicon alloyed with iron for furnace deoxidation has been the subject of an extensive cooperative investigation between the United States Bureau of Mines, the Carnegie Institute of Technology, and the Metallurgical Advisory Board. Certain grader of steel, especially low-carbon rimming steels, require a low-carbon deoxidizer to keep the finished steel within the carbon specification after deoxidation. ACKNOWLEDGMENTThe authors wish to acknowledge the assistance of J. F. Sanderson and S. S. Johnston in the analysis of the alloys used in this work.PURPOSE OF WORKThe need for definite information as to which compositions of manganese and silicon within a certain manganese-silicon ratio and when alloyed with iron would have an allowable carbon content for the particular grade or type of steel on which the deoxidize is used, prompted the undertaking of this investigation to determine the solubility of carbon in manganese, silicon, and iron alloys within the region bounded by 10:1 and 4:l manganese to silicon ratios. These data should be of value to the manufacturer producing such"

May 1, 1934

By Oliver Bowles

Whiting or Paris white is a fine-grained preparation of calcium carbonate having a wide variety of uses. Until recent years it was prepared almost exclusively from certain north European chalks. With the curtailment of imports of European chalk during the World War of 1914-18, however, finely ground limestone, of domestic origin was used more extensively to satisfy the American demand.

Jan 1, 1942

By T. N. Williamson

Most U.S. coal production is bituminous coal. Some 90% of current production comes from a geographical area enclosed in a circle with a 300 mile radius and its center at about Huntington, West Virginia. There are important underground coal production areas in the western parts of the United States as well. Most U.S. coal production comes from fairly level seams, many of which pitch rather uniformly only a few feet per mile. Usually there will be several overlying seams of varying thicknesses, separated by several tens of feet. Fig. 1. 1. Seams have minor local undulations but these? are small enough not to be a major consideration in a horizontal drilling research program.

Jan 1, 1970

By J. D. Warne

The ferberite district of Boulder County, Colo., has been an important producer of tungsten since 1900. During World War I, high prices for tungston concontrates resulted in a brief period of intense activity, and the production in 1917 was 2,707 tons of 60 percent W03 concentrates. Production declined thereafter, and in 19.2 the tungsten produced in Boulder County represented about 4 percent of the Nation's output, being exceeded only by the scheelite production in California, Nevada, and Idaho. Boulder County has boon an important source: of tungsten in the Korean emergency; the present report does not describe this recent activity, as it will be covered by a future publication. Tungsten occurs in small ore shoots of narrow and irregular veins. Most of the ore shoots have been found outcropping on the surface. Core drilling; has been used by the larger operators to explore for new veins and to locate extensions of known veins.

Jan 1, 1953

By J. W. Thompson

A contract stipUlating for the delivery of quantities of phosphate rock" f. o. b. mines," and stipUlating that" while this contract is in form an absolute sale for a fixed quantity in each year, it is mutually understood and agreed that the purchase is for the buyer's consumption and not for a sale; the buyer agreeing to give to seller the refusal of any surplus over and above the actual consumption. Buyer is at liberty to increase or diminish the quantity called for in any year, to the extent of not exceeding 10 per cent; provided that the quantity to be taken shall not be less than buyer's consumption; provided further that notice of such increased or diminished demand be given seller 12 months in advance of such change," is to be construed as a contract for the sale of stated quantities of rock, deliverable in approximately equal quantities during each year for the specified series of years, subject only to be increased or diminished after specified notice in any year, where the amount taken would not be les<; than the buyer's consumption, not exceeding 10 per cent, and the contract indicating that the rock was intended by both parties for consumption in the fertilizer plant of the buyer. but the quantity to be taken was not limited by the necessities of' the plant.

Jan 1, 1916

By W. R. K. Wu

Results of linear correlations of two to four variables by the least-squares method are presented. The variables include 63 parameters representing coal composition, coal plasticity, and coke strength. The composition parameters are on chemical analyses; the plasticity parameters, on three plastometer and dilatometer tests and four miscellaneous tests; and the coke-strength parameters, on three ASTM indices. Seventy-two to eighty-four plastic coals were used in the plasticity and carbonization tests, which together form the basis of this report; 43 nonplastic or weakly plastic coals were used in the coal-band studies. Plots of relations between volatile matter, carbon, and oxygen contents of 1,860 U.S. coals and the 84 coals used are shown. Similar plots between volatile matter and hydrogen or atomic H/C of the 84 coals are also included. Significances of regression coefficient signs for coal composition parameters in the significant correlations found are discussed. Based on these significances, the following relations are shown: (a) coke strength versus average aromaticity, or mineral matter content, of the parent coal; (b) characteristic temperatures of the plastometer and dilatometers, the free-swelling index, or the Gray-King type versus average hydroaromaticity of the coal; and (c) nontemperature parameters of the plastometer and dilatometers versus the physical properties of a certain group of compounds from thermal decomposition of coal. Similarly, significances between the positions of coals in the coal band and the aforementioned relations are also discussed. A structural theory of coal plasticity is proposed. Applications of the correlation results are discussed. Composition parameters, such as carbon, atomic H/C, and calorific value may be used as a basis for selecting coking coals for stronger coke. Plasticity parameters, such as the end temperatures of the plastometer and dilatometers and the free-swelling index, may be used for the same purpose. Based on the best correlations found, coke-strength indices may be estimated to within 4 to 8 units of the observed values; the end temperatures of the plastometer and dilatometer tests, 5° to 10° C.; and the free-swelling index, within 1 unit. Accuracies of all these estimated values are examined, based on the experimental errors of the data involved. Finally, estimations of plasticity parameters from one test with those from others are shown.

Jan 1, 1971

By James W. Wade

This paper describing the mining practices at the Tintic Standard mine is one of a series being prepared by the United States Bureau of Mines. In the preparation of this paper each subject has been presented by the engineer in charge. L. R. Dobbs wrote the part pertaining to tae technique of square-set mining, J. M. Snow the part on geology, and M. D. Paine, the part on ventilation. All of the drawings are the work of H. W. Waterfield of the engineering department. The statistics of the Tintic district ware prepared by A. G. MacKenzie. Each writer has attempted to show the difficulties that arise in operating and the practices used to overcome them.

Jan 1, 1930

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By Robert E. Barieau

The following zero pressure thermodynamic properties of nitrogen gas are tabulated: [C°p, H° -o, S°], These properties are tabulated in units of joules, gram mole, degrees Kelvin and in calories, gram-mole, degrees Kelvin for every degree Kelvin from 50° to 550°. The same functions are also tabulated in units of British thermal units pound-mole, degrees Rankine for every degree Rankine from 100° to 1,000°.

Jan 1, 1967

By E. P. Carman

In this report, the Federal Bureau of Mines presents a summary of the occurrence, properties, and uses of some natural bitumens, using the layman&apos;s or dictionary definition of bitumens - that is, naturally occurring hydro-carbons. Emphasis is on the less common solid and semisolid bitumens, particularly those occurring or used to some extent in the United States. This comprises data from many sources and references to these sources for more detail than is given in this summary. This paper was prepared primarily to answer questions about some of the less known bituminous materials. The word hydrocarbons could just as well have been substituted in the title for bitumens, but bitumens was used, since an abstract of the paper was presented at a meeting where the major emphasis was on bituminous materials. The reader will realize that coals, of which only the more unusual such as the cannel coals and torbanites are discussed in this paper, are primarily mixtures of bituminous materials and carbon. The amount of bituminous material, or volatile matter, in coals is greatest in the lower rank coals and the unusual types described in this paper, and decreases as coal rank increases. However, since no method other than destruction of the original coal substance by heat is known that will separate the volatile matter from the carbon, it appears reasonable to classify the coals with other bituminous materials, particularly since bituminous coal - the most widely used coal - by its name indicates the combination of bituminous materials and carbon.

Jan 1, 1961

By Carl R. Peterson

The Rapidex continuous spiral blast tunneling concept uses a spiral blast pattern that provides efficient slabbing action, continuous progression, and partial self-shielding. A lightly shielded tunneling machine using this concept stays at the face to provide continuous drill, load, shoot, and muck functions. Previous phases proved the effectiveness of the blast pattern in the White Pine Shale tested the design features of the shield and developed a remote loading and shooting capability using inductively initiated blasting caps and a pumpable slurry explosive. Phase IV assembled previously used front-end elements (drill, loading components, shield) on a used Joy loader chassis and added a mucking system television monitoring and remote control elements. Remote television monitored loading shooting and mucking were investigated. Difficulty was experienced in locating previously drilled blastholes near the bottom of the heading and even on the face. These holes often had to be considered as lost. Because of hydraulic system deficiencies and overall congestion of machine elements at the face mucking rates obtainable with remote television monitoring were low (on the order of 16 tons per hour). Performance was good enough to indicate improved rates if more space were available and if extreme thoroughness were not required. Because of the serious nature of the lost hole problem, a new explosive loading scheme was given a preliminary evaluation. The new scheme would require the explosive and the detonating charge to be loaded through the drill steel. If the necessary equipment modifications could he made and if safe, efficient operation were assured, the new scheme would alleviate some of the crowding at the face and would eliminate the lost hole problem.

Jan 1, 1978

By L. C. IlsLey

The United States Bureau of clines has been conducting Investigations of electrical equipment during a period of more than 25 years in an endeavor to encourage the development of safer electrical equipment for coal mines. In order to conduct these investigations in an orderly manner they are carried out under a published schedule of tests known as Schedule 2C, which specifies detailed requirements for motors, controllers, etc., and fees covering the various inspections and tests made as part of a routine investigation.

Jan 1, 1937

By W. D. Mcmillan

Important reserves of nickel ore occur in the Levies district in Oriente, Cuba. The area is mountainous and mostly covered by heavy vegetation. The ore bodies comprise surface tracts of nickeliferous laterite underlain with decomposed serpentine of ore grade. The Cuban Nickel Co., a wholly owned United States Government corporation, owns a plant for leaching the nickel from its ores at Nicaro, Oriente, Cuba, Between December 1943 and March 31, 1954, 5,902,225 short tons of ore was treated, with a recovery of 116,206,519 pounds of nickel (52,711 metric tons). In 1953, 1,330, 224 short tons of ore was mined and 27;"3,129 pounds of nickel produced. The Cuban Nickel Co. also owns a townsite, with the necessary facilities, mining equipment, and 11 miles of railroad. Ore for the plant has been produced from the Ocujal-San Juan claims on lends owned by the Nicaro Nickel Co., a sub¬sidiary of Freeport Sulphur Co. The Government enterprise is man-aged by the Nickel Processing Corp. The Cuban Nickel Co. has denounced mineral concessions and has purchased other claims from private owners.

Jan 1, 1955

By David C. Byrne

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupation-al Research Agenda, problems created by occupational hearing loss include(1) reduced quality of life due to social isolation and unrelenting tinnitus,(2) impaired communication with family members, the public, and coworkers, (3) diminished ability to monitor the work environment (i.e., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers’ compensation and hearing aids. Although eliminating hazardous noise is the long-term solution to the noise problem, miners will likely need to rely on personal hearing protection in certain situations for quite some time. However, it is well known that noise attenuation provided by hearing protectors as they are worn during everyday use is usually quite different (i.e., worse) than when tested under lab conditions. In addition, workers may refuse to wear their hearing protection for any number of reasons. This project was initiated to evaluate practical technological advances in hearing protectors, with an emphasis on optimizing the balance between effectiveness, comfort, over protection, and communication ability. The recently completed auditory research facility is now under-going the accreditation process conducted by the National Institute of Standards and Technology under the National Voluntary Laboratory Accreditation Program. Experiments are planned to investigate the factors that affect a miner’s ability to hear hazard and warning sounds (e.g., roof working, alarm signals, spoken communications, etc.). A service contract has been initiated to record and digitally store samples of typical warning sounds heard in an underground coal mine. This information will be analyzed in the lab to develop recommendations that can be offered to the mining community regarding correct earplug/earmuff usage to maximize there cognition of hazard and warning sounds while adequately protecting the miners’ hearing.

Jan 12, 2001

By V. B. Dale

This is one of a series of reports covering the mineral resources of the Nation. It describes briefly most of the known tungsten deposits in Yuma, Maricopa, Pinal, and Graham Counties, Ariz. Most of those described were examined by the author. An effort was made to determine the position of the various deposits by section, township, and range and to give accurate road direction to each property from a prominent landmark. All available maps have been used in making these determinations, but in unsurveyed areas it was necessary to make approximate projections of subdivisions. The township and range numbers refer to the Gila and Salt River base and meridian.

Jan 1, 1959

By A. Baldwin

Reports technical progress in designing four machines to be used in mining coal underground, applying innovative concepts at the design stage (instead of add-ons). A study phase was followed by design activity, including calculations supporting the designs. Scale models of three machines were built, and a full-scale mock-up of the conventional loader was used to measure human factors parameters.

Jan 1, 1976