Search Documents

By R. T. C. Rasmussen

"INTRODUCTION This is the second report of investigations describing tests in full-scale commercial heats of steel-using electrolytic manganese having a purity of about 99.95 percent, produced in the Bureau's pilot plant at Boulder City, Nev. The first report dealt with tests in cooperation with two companies can the use,of electrolytic manganese in the manufacture of stainless steel. 3/ Plans aril cost estimates for reasonably large commercial, electrolytic plants based upon pilot-plant experience, as well as the comments of a number of concerns where electrolytic manganese has been tried, are contained in another publication.4/ The tests in cooperation with industry are part of the Bureau of Mines program of investigations of methods of utilizing low-grade domestic manganese ores, thereby the United States leas dependent upon foreign sources of manganese for metallurgical use. The Boulder City pilot plant already has demonstrated the feasibility of producing electrolytic manganese from several of the most important reserves of low-grade manganese ore. As the ferromanganese normally used by the steel industry represents the bulk of the Nation's manganese requirements, the usefulness and possi¬ble advantages of electrolytic manganese in the manufacture of steel must be established if electrowinning from domestic ores is to become an important factor of manganese supply.Preliminary arrangements for the cooperative tests at the Atlas Steel Casting Co., Buffalo,. N. Y., were made with E. L. Altenburg, vice president and general manager of the company, by A. A. Dow. 5/ The data on the tests at the Atlas plant presented herein are based upon reports of E. L. Altenburg and information obtained by the author during a visit to the plant to observe the initial trial heats with electrolytic manganese in the open-hearth and the electric furnace."

Nov 1, 1945

By J. D. Davis

THIS REPORT gives results of an investi¬gation of the carbonizing properties of coals from Pittsburgh bed, Jamison No. 9 mine, Marion County, W. Va., and from Upper Freeport bed, Bull Run No. 1 mine, Preston County, W. Va. The study included Bureau of Mines-American Gas Association tests at 800° and 900° C. and various chemical and physical tests designed to evaluate the plastic, expanding, and agglutinating properties of coal. A blend of each coal was carbonized in the 500-pound slot oven. The carbonization sample of Pittsburgh coal contained 2.7 percent moisture, 35.8 percent volatile matter, 54.4 percent fixed carbon, 7.1 percent ash, and 0.9 percent sulfur. It contained 60.9 percent fixed carbon on the dry, mineral-matter-free basis and had a heating value of 14,780 B. t. u. per pound on the moist, mineral-matter-free basis. It therefore ranks as high-volatile A bituminous and was blended with low-volatile Pocahontas No. 3 coal. Upper Freeport coal contained 2.8 percent moisture, 27.7 percent volatile matter, 60.9 percent fixed carbon, 8.6 percent ash, and 1.0 percent sulfur, as carbonized. It contained 69.5 percent fixed carbon on the dry, mineral-matter-free basis and therefore ranks as medium-volatile bituminous. It was blended with high-volatile A Pittsburgh coal from Allegheny County Pa.

Jan 1, 1952

By R. E. Chaney

This report summarizes the research on the Strategic and Critical Materials Program tasks conducted at the Idaho National Engineering Laboratory (INEL) between Mdy 1983 and April 1984. The work is divided into two areas: 1. Production Technologies - Tasks directed at developing advanced extraction technologies ? Biologically-Assisted Minerals Processing ? Metal/Gas Reactions and Thermal Plasmas ? Dehydration of Aluminum Chloride Hexahydrate. 2. Conservation/Substitution Technologies - Tasks directed toward establishing the technical processing base which will permit the use of advanced materials ? Joining of Rapidly Solidified Alloys (RSA) ? Joining of Silicon Nitride-Based Ceramics ? Nondestructive Evaluation of Ceramic and RSA Joints and Materials.

Jan 1, 1984

By R. J. Pokora

This Bureau of Mines report is an applications manual that can be used by the nonmetallic mining industry for guidance in installing noise control materials into crushing and screening plants. These noise control modifications were installed and successfully tested at three operating quarries. This report identifies the major noise sources that can be encountered in crushing and screening plants, and discusses the applicable noise control materials and techniques that a plant operator can utilize on a retrofit basis to reduce equipment noise.

Jan 1, 1984

By Ellis S. Hertzog

The data published in this retort cover only one phase of a special study of tile physical and chemical properties s of only Alabama coals made by the Bureau of Mines. In addition to determinations of friability, the survey included determinations of grindability, B.t.u. value, and ash-fusion temperature. Assay distillation tests, both for high- and low-temperature carbonization, and proximate and ultimate analyses were made also. However, this preliminary paper is concerned only with the results of friability tests and is issued to expedite the release of this information to the public. The friability, test measures the liability of a coal to break into smaller pieces when subjected to repeated handling, as occurs in the mining, preparation, and transportation operations. Friability depends on many physical characteristics of the coal that vary not only between different seams but also in the same seam. The laboratory methods of determining friability have been developed to give a practical means of estimating degradation of size. So far as is known to the authors, no data on the friability of Alabama coals have ever been published. This caper makes available for the first time fairly comprehensive3 information on this subject. Because the procedure for the tumbler test for determining the friability of coal is relatively new to the coal operators, the authors Lave included a, complete description of it in this report.

Jan 1, 1938

By G. S. Knoke

This report presents the results of a demonstration of the technical, economic, and environmental feasibility of hydraulic borehole mining of shallow oil sands. Borehole mining offers a method for extracting the oil sands with minimal disturbance to environmental quality because (1) no overburden is removed, (2) no waste rock piles are required, (3) the tailings can be backfilled into the borehole cavity, (4) the ground water quality should be undisturbed, (5) a closed-loop water system can be employed so that no surface streams are polluted, and (6) surface subsidence can be minimized by backfilling the mined cavities. This project consisted of two concurrent tasks: mining operations and environmental monitoring. To generate the environmental impact, nearly 1000 tons of oil sands were mined from two boreholes. Water quality and ground subsidence were monitored. No significant changes occurred in the chemical composition of the process water, indicating that the borehole mining process does not dissolve the mined material. The average subsidence in the immediate vicinity of the boreholes was about 1/2 inch, although some points were noted to be slightly elevated. In general, the amount of subsidence increased with time and decreased with distance from the bore-hole. A mining cost analysis was used to project an estimated cost for production mining of about $38 per barrel of oil.

Jan 1, 1980

By John Nagy, Hylton R. Brown, Irving Hartman

"INTRODUCTION The tests described in this publication were planned to provide information on the explosibility of metal-powder dust clouds. This subject has become increasingly important because of the large quantity and variety of metallic powders now used for military and industrial purposes. To provide the increased amounts of metallic powders needed in the manufacture of munitions and to supply the demand created by the rapid growth of powder metallurgy, existing metal-powder plants have been enlarged, production schedules accelerated, and new plants erected. In some cases new methods of producing metal powders have been developed. This increased production and the development of new manufacturing methods have caused an increase in the number of metal-powder fires and explosions, with accompanying heavy loss of life and property. These have emphasized the need for information on methods of providing protection against hazards inherent in the production and handling of powdered metals. This paper gives results of laboratory inflammability and explosibility tests made to April 1, 1943, and is a progress report. Many descriptive details have been omitted purposely; they will supplied in a later publication, expected to be a Bureau of Mines bulletin."

Oct 1, 1943

This publication contains 10 papers presented at a symposium on ATRS systems in Charleston, WV, on June 23, 1983. Included are papers by MSHA Technical Support (Roof Control), West Virginia Institute of Technology, the Bureau of Mines, and seven roof bolter manufacturers and/or designers of ATRS systems. These papers summarize the most recent developments in ATRS technology and can serve as a guide to potential designers, developers, and users of ATRS systems.

Jan 1, 1985

By Sidney A. Suhler

A field operable, breadboard model, borehole radar was developed for the detection of hazardous geological anomalies in and above a coal seam in advance of mining. A four-inch diameter downhole probe was fabricated and tested in several environments. The radar transmitter was also employed in a cross-hole or through transmission mode to determine natural geotechnical and man-made conditions between boreholes. Sensitivity to underground conditions in both modes of operation were indicated.

Jan 1, 1978

By C. B. Manula

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a Southwestern surface mine using draglines and front-end loaders is described. The specific objective of the study is to demonstrate the application of the simulator to analyze mine planning and to analyze alternatives for increased production. The simulator was verified by comparing long term production figures to the simulated results from data collected on a mine visit. A short term and a long term alternative are studied with projected productivities and scheduling. No economic analysis of these proposals were performed.

Jan 1, 1977

By J. B. Carman

This paper, describing the concentrator of the Molybdenum Corporation of America in Taos County, northern New Mexico. 7 miles east of Questa, is one of a series on milling methods being prepared for and published by the United States Bureau of Mines. The mine from which the ore comes is 1 1/4 miles from the mill, and produces about 40 tons of ore per day by the cut-and-fill method.3 The ore contains about 5 per cent of MoS2. The mill has a capacity of 50 tons of ore per day and utilizes flotation methods. Water is taken from Red River. Power is generated by a water wheel, or by a Diesel engine in times of water shortage during the winter. The mill is located close to the bottom of a canyon, in order to obtain maximum head or, the water wheel, and the flow of ore is therefore maintained partly by gravity and partly by an elevator and pumps. ORE TREATED The MoS2 content of the concentrator feed ranges from 4.5 to 7.5 biotite, fluorite, small amounts of rhodochrosite and calcite, and the minerals of the granodiorite country rock.

Jan 1, 1932

By J. W. Paul

The material that composes the roof in coal mines differs in strength according to variations in its physical nature and characteristics. Some material such as limestone and massive sandstone, (free from slits) and carbonaceous shale or bone, will often remain in place in narrow work without the use of timber or other means of support, but in wide places the use of supports becomes a real necessity. Roof material composed of shale, fire clay or small laminations of sandstone, or shale or sandstone interspersed with laminations of thin coal, presents conditions that call for timber support in both narrow and wide work. However, in narrow work such unstable roof material may be taken down until the strata assume an arch that is self-supporting for overlying firm strata such as a roof coal, a touch weather-resisting, shale, sandstone, or limestone. The proper support of the roof in roadways used for haulage or travel adds to the economy of operation by preventing delays in transportation and increases the safety of those who travel these roadways.

Jan 1, 1930

By Stephan Stecura

Crystallographic modifications and kinetics of solid-state phase trans-formations were determined for five rare-earth" sesquioxides--La2O3, Nd2O3, Sm2O3, Eu2O3, and Gd2O3. Oxides used for crystal modification studies were prepared by thermal decomposition of the following high-purity salts of the five rare-earth elements--carbonates, chlorides, fluorides, nitrates, oxalates, and sulfates. X-ray diffraction patterns of the cubic and hexagonal oxides were indexed by a graphical method and patterns of the monoclinic oxides by Ito's method. The kinetics of crystallographic transformation were determined by high-temperature X-ray diffractometry. The kinetic data were interpreted using a shrinking sphere model. All of the transformations followed first order kinetics. Activation energies were calculated by application of the Arrhenius equation. These solid-state phase inversions were concluded to occur by a reconstructive transformation mechanism.

Jan 1, 1965

By Graham W. Marks

Recently it was shown the total energy method of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing, this work, the present report deals with analyses for beryllium, zinc, cadmium; and indium. There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved. As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is, associated with zinc and cadmium in zinc ores.

Jan 1, 1948

By Lloyd H. Banning

Crucible-smelting tests at the Northwest. Electrodevelopment Laboratory and a pilot-plant test on electric smelting of western phosphate rock for the Westvaco Chlorine Products by the Tennessee Valley Authority indicated that the small vanadium content of the rock is concentrated in the ferrophosphorus by-product of Phosphorus smelting. This research is concerned' mainly with recovering vanadium and phosphorus froth the ferrophosphorus produced from western phosphate rock. Exploratory tests were made of several methods of treating vanadiferous ferrophosphorus. Attempts to separate vanadium as a carbide dross by saturating molten ferrophosphorus with carbon were unsuccessful. Volatilization of phosphorus from ferrophosphorus was accomplished to some extent, both with and without addition of sulfur in several forms, but elimination of phosphorus was not complete. Brief testing in a small experimental converter on oxidation of vanadium and phosphorus; into a slag by blowing with air showed promise. A method that comprised fusing vanadiferous ferrophosphorus mixed with soda ash under oxidizing conditions gave encouraging results and was tested beyond the preliminary stage. A slag product of the fusion contained most of the phosphorus and vanadium as water-soluble sodium phosphate and. virtually water-insoluble sodium vanadate. After leaching the sodium phosphate froth the slag, the leach residue was reroasted with soda ash and salt. This roasted product was leached again with water to extract the vanadium.

Jan 1, 1951

By John C. Feeley

This paper is the result of a field study of prospect drilling in the Florida phosphate fields. The objective is to describe the drilling methods employed . . Since the general policies of the operating companies in the land - pebble area do not permit the dissemination of prospecting information and costs thereof , the writer has carefully avoided mentioning names and locations except by reference to existing publications ,

May 1, 1949

By John E. Conley

Of the three chemical elements most vitally essential for plant growth the United States, before World War I, had developed ample domestic supplies of but one-phosphorus. During and shortly after the war period, the fixation of nitrogen was greatly expanded in this country, as in many others, insuring a supply adequate for agriculture as well as for munitions. However, in spite of a search for sources of the third element, potassium, which began years before the war, attained almost frantic intensity between 1914 and 1919, and continued for 10 years thereafter, it was not until 1921 that the American Trona Corporation put its Searles Lake operations into continuous production. This company in 1926 became The American Potash & Chemical Co. but has never supplied much more than 15 percent of the potash consumed in the American market. Likewise, though discovered in 1921 in drill cuttings from oil wells, it was not until 1926 that domestic deposits of potassium salts adequate to render the United States independent of foreign sources of supply were proved to occur in the Permian Basin of Texas and New Mexico.

Jan 1, 1944

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood-block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 2010

By Edmund Newton

The Haile mine has been the outstanding gold-mining operation and the largest single producer of gold in the Appalachian region. Gold was discovered at the Haile in 1827, previous to the present operation, production has been nearly $4,500,000 (gold at $20.67 per ounce.) from somewhat over a million tons of ore, with an average extraction of about 70 percent. The Haile property, now operated by Haile Gold Mines, Inc., is in the southern part of Lancaster County, South Carolina, 3-1/2 miles northeast of the town of Kershaw and 55 miles north of Columbia, the State capital. (See fig. 1.) The corporation has a lease and purchase contract on 1,805 acres, covering the present productive area. In addition, it holds lease contracts on 1,500 acres additional adjacent to this area.

Jan 1, 1940

By Walter G. Dupree

When the original version of this study was published in 1972 it was evident that a problem was developing on the energy scene. The ability of the United States to find the energy supplies it needed within its own boundaries--at least in the forms desired--was declining. Production of crude oil in the United States had peaked in 1970 and was declining slowly; environmental restrictions had begun to hamper the production and consumption of high sulfur coal; natural gas reserves were beginning to dwindle; and the development of nuclear power was proceeding more slowly than originally planned. Shortfalls in energy supply were being met through the importation of increasingly larger quantities of petroleum, but supplies were adequate and the price of the imports was below that of domestic production. The energy problem was more prospective than current. In October of 1973 the prospective problem became the "Energy Crisis' when the Arab petroleum exporting countries reduced crude oil production, imposed an embargo on the shipment of crude oil to the United States, and then raised the price of crude oil in a series of large steps. This crisis was a clear demonstration of the dangers of the dependence of the United States on imported petroleum, and of the Nation's vulnerability to the actions of the oil exporting countries. After the embargo was lifted, attention shifted to the immediate hardships resulting from the higher prices for gasoline, fuel, and electricity,

Jan 1, 1975