Search Documents

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1986 was $405.2 million, a slight decrease from that of 1985. Alabama was second in the Nation in production of bauxite, crushed marble, and ferroalloys; third b fire clay; fifth in masonry cement and lime; sixth in total clays; and seventh in recovered sulfur. Alabama ranked 19th nationally in value of nonfuel minerals produced. Cement, clays, lime, sand and gravel, and stone were the major commodities produced.

Jan 1, 1988

By Steven J. Page

Since 1982 standard calibration materials recommended for respirable crystalline silica analysis by the Mine Safety and Health Administration (MSHA) P7 Infrared Method and the National Institute for Occupational Safety and Health (NIOSH) X-ray Diffraction (XRD) Analytical Method 7500 have undergone minor changes in size distribution. However, a critical assumption has been made that the crystalline silica in ambient mine atmosphere respirable dust samples has also remained essentially unchanged in particle size distribution. The objective of this work, therefore, is to compare recent particle size distributions of underground coal mine dust and the silica component of these dusts with estimated aerodynamic particle size distributions of calibration standard materials MIN-U-SIL 5, Berkeley 5, and SRM 1878 used by two crystalline silica analysis techniques. This work provides resolution to a previously reported discrepancy involving the proper sample dilution for the particle sizing method used. Dust impactor sampling data for various locations in 13 underground coal mines were collected between 1991 and 1998 and analyzed for the respirable mass median aerodynamic diameters. The data suggest that the MSHA P7 Method will underestimate the silica content of the sample by at most 8.5 % in the median size range of 0.9–3.6 µm and that it is unlikely one would obtain any significant error in the MSHA P7 Method analysis when the method uses Berkeley 5, MIN-U-SIL 5, or SRM 1878 as a calibration standard material. The results suggest that the NIOSH Analytical Method 7500 would be more appropriate for a dust sample that is representative of the total (no cyclone classifier) rather than the respirable airborne dust, particularly since the mass fraction in the size range below 4 µm is usually a small percentage of the total airborne dust mass. However, the NIOSH Analytical Method 7500 is likely to underestimate the silica content of an airborne respirable dust sample by only 5–10 %. The results of this study also suggest that any changes that may have occurred in the median respirable size of airborne coal mine dust are not significant enough to cause any appreciable error in the current methods used for respirable crystalline silica analysis.

Aug 3, 2005

By W. R. Byrnes

This project was initiated on October 1, 1980 and will be completed on December 31, 1983. The project was Initially approved and funded by the Office of Surface Mining and subsequently was moved to the jurisdiction of the Bureau of Mines. It was administered through the Indiana Mining and Mineral Resources Research Institute. The research was done to assess reforestation success and ultimate productivity for areas reclaimed under the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87). The Permanent Regulatory Program for implementation of P.L. 95-87 Includes provisions for revegetation that require seeding of ground cover plants to control erosion until permanent vegetation such as tree species Is established, and restoration of mined land to its original or better productivity. Much of the land to be surface-mined presently supports forest cover and it is anticipated that reconstructed minesoils will exhibit high productive potential for hardwood tree species. Hence, information was needed on compatibility of ground cover and tree seedlings when established concurrently as well as on revegetation success under postmining versus premining conditions.

Jan 1, 1983

"Requests are frequently received by the Information Service of the Bureau of Mines for published information on the coals of different foreign countries, as compared with coals mined in the United States. The analyses of various coals from several countries on the Pacific, which were submitted to the Fuels Division for certain tests between the years 1913 and 1916, may be of interest, and are shown below: Results of Analyses of Various Coals from China, New Zealand, Japan and Australia."

Sep 1, 1925

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

By Michael L. Boninger, Erik J. Wolf, Rory A. Cooper

Although wheelchair users are regularly subjected to whole-body vibrations little research has been conducted to assess these vibrations or attempt to reduce them [2,3,5]. Most of the wheelchair and whole-body vibration research done to this point has been conducted on manual wheelchairs. Van Sickle et al showed that manual wheelchair propulsion over a simulated road course produces vibration loads that exceed the ISO 2631-1 standards for the fatigue-decreased proficiency boundary at the seat of the wheelchair as well as the head of the user [6]. In a study by Boninger et al [1], 66% of wheelchair users reported neck pain since acquiring their wheelchair. One of the key reasons believed to be the cause of pain, was the exposure to whole-body vibration. Kwarciak et al [4] and Wolf et al [7] performed similar studies using two methods of analysis to evaluate vibrations on suspension and non-suspension wheelchairs while descending curbs of varying heights. Both studies revealed no significant difference in the abilities of the wheelchairs to reduce the amounts of vibrations transferred to the wheelchair user. Although the efforts of wheelchair companies to reduce the amounts of whole-body vibration transmitted to wheelchair users through the addition of suspension systems is encouraging, the technology is not yet ideal. Additionally, the research to date has focused on manual wheelchairs exclusively, while little attention has been shown to powered wheelchairs. Methods This study includes the use of two suspension electric powered wheelchairs: The Quickie S-626 and the Invacare 3G Torque SP Storm Series. Each subject tested all of the configurations of the suspension wheelchairs. These included the Invacare with suspension, the Quickie with suspension set to three settings (most stiff, least stiff, and 50% stiffness), and both wheelchairs with solid inserts to act as non-suspension wheelchairs. Sixteen able bodied subjects have been recruited for this study so far. In each of the configurations of the wheelchairs, the subjects traversed an Activities of Daily Living (ADL) course. Vibrations were collected from a tri-axial accelerometer attached to a seat plate beneath the cushion during driving over the activities course. A mixed model ANOVA was used to determine if there were differences between suspensions based on Vibration Dose Value (VDV). Results Statistical analyses of the VDV data revealed significant differences between the six different suspensions over each of the obstacles in the activities of daily living course. Post-hoc analyses revealed that for each of the obstacles, significant differences existed between the Invacare suspension and the Invacare solid insert. For the Quickie power wheelchair the solid insert setting was not significantly different from the most-stiff setting for each of the obstacles

Jan 6, 2006

By R. J. Fantel

The Bureau of Mines investigated the resources, costs, capacities, market relationships, and short- and long-run supply of phosphate rock and phosphoric acid. The 206 mines and deposits evaluated in 30 market economy countries contain an estimated 35.1 billion mt of recoverable phosphate rock (demonstrated resource level). U.S. resources are sufficient to satisfy the domestic and export markets for phosphate products well beyond the year 2000. Because of resource depletion at current producers, however, new properties (with higher cost levels) need to be developed if U.S. production levels are to be maintained. Existing worldwide capacity can satisfy expected demand through the early 1990's. Expansion at existing mines or low demand growth could mean that no new property development will be needed before the late 1990's. Worldwide, almost $8 billion could be required for development of new phosphate rock properties between now and the year 2000, given 3-pct annual growth in demand. Most properties that could develop in the 1990's would require price increases of 20 to 50 pct to break even. To earn a 15-pct rate of return on investment, prices must rise to nearly double the present level of $24 to $29 per metric ton.

Jan 1, 1988

In This Chapter [Finding the dust source Ventilation and dust collector malfunctions Upgrading the dust controls Design stage ventilation planning ] This chapter explains how to reduce respirable dust76 in hard-rock tunnels during excavation by using tunnel boring machines (TBMs). The first steps in combating a dust problem are to take dust samples to pinpoint the source, check the ventilation system, and check the dust collector. If the ventilation system and dust collector are operating properly, then other dust controls such as water sprays and conveyor belt scrapers must be upgraded. For tunnels in the design stage, recommended air quantities are provided. FINDING THE DUST SOURCE AND LOOKING FOR VENTILATION MALFUNCTIONS [The first steps in fighting a dust problem are to take dust samples to pinpoint the source, check the ventilation system, and check the dust collector. Without knowing the exact source, efforts to reduce dust are hit-and-miss (mostly miss).] Taking samples to pinpoint the dust source. In tunnels with high levels of airborne dust, the first task is to pinpoint where the dust enters the airstream. Most dust originates from rock breakage at the tunnel face, but the location where this dust enters the airstream can vary. Dust can leak from behind the TBM face shield, from gaps in the ventilation duct, or from a mal-functioning dust collector. It can be entrained into the air from the muck on a moving conveyor belt. It can even be shaken loose from the underside of the belt as it passes over the idlers. As a start, to locate the dust source, dust samples and air quantity measurements should be taken at the following locations:

Jan 6, 2003

By Charles Vaught, JON VOLKWEIN, ROBERT PETERS, ERICA HALL

Since 1999, the CWP level among miners with 25 years or more experience, for instance, has risen from slightly more than 4% to 9% (See Figure 1). While it is obviously necessary to protect all miners’ lungs, there is now a technology to improve the chances that new miners’ lungs will be protected from the day they begin work.

By Mark S. Redfern, Kim M. Corneliusa, Christopher A. Hamrick, Sean Gallaghera

Coal miners often handle heavy electrical power cables, weighing up to 10 kg per meter. These cables are manually lifted and attached to the mine roof to prevent damage from mobile underground equipment. Data suggest that workers who commonly perform cable handling tasks experience a high rate of lost time back injuries. In this study, six male underground miners performed a total of 12 cable-hanging tasks in standing, stooping, and kneeling postures, during which kinematic and ground reaction force data were collected. Reductions in vertical work space were found to result in a linear increase in the peak moment experienced by the lumbarspine (p<0.05). In restricted postures, peak moments were not significantly different in stooping vs. kneeling postures (p>0.05). Average lumbopelvic flexion during the tasks was highest in stooping conditions, followed by standing and kneeling exertions (p<0.05). Implications of this data with respect to design of cable handling tasks are presented and discussed. Keywords: Biomechanics, posture, low back pain, restricted workspace, mining

By R. Newman

An inexpensive slow-speed data acquisition system has been adapted to digitally record multiple parameters simultaneously at intervals of 15 seconds. The system was built for use with standard soils testing equipment to automatically record load and displacement parameters at predetermined instants in time. Simultaneous readout is achieved by the use of special signal conditioner and sample-and-hold circuits which read the multiple signals simultaneously and hold them until the slow acting system can print out. Three channels of a 10-channel system have been converted and found to operate successfully during a series of direct shear tests. A unique feature of the system, which significantly reduced its cost, is the power supply units. Dummy circuits are used to maintain a constant power demand during sampling) thus eliminating the need for a costly power supply with rapid response characteristics. The entire system, having an overall accuracy of 0.25 percent, was put in operation for a cost under $2,500.

Jan 1, 1970

By Manuel Gomez, V. F. Parry, John B. Goodman

"INTRODUCTION The need for an accurate and precise analytical method for determining moisture in coals of high water content has been recognized by the coal industry as well as the fuel technologist. Interest in this particular phase of coal technology extends back to the early work of German investigators on the brown coals of Central Europe. Studies by these workers led to the establishment of a direct immiscible liquid-distillation method 4/ as the accepted moisture determining technique in European laboratories. Direct moisture determining methods, those methods that utilize various techniques to drive off the water from a given sample of coal and either collect the water in a calibrated receiver or selectively trap the water driven off in a suitable absorber, have found little favor in the United States. They have been treated merely as research tools.5/ The problem of moisture determination in low-rank coals of the United States has not been given much consideration because such coals contribute only about 2 percent of the total United States production. With renewed activity in low-temperature carbonization and with the growth of interest in coal and coal-tar hydrogenation, the American coals of lover rank containing 20 to 40 percent bed moisture will be subjected to extensive investigation. If the low-rank coals of the United States are to be accurately appraised, the need for qualitative and quantitative analytical proceeded becomes more pronounced. These coals, especially the lignites of Texas and North Dakota, are highly susceptible to oxidation, a process that proceeds to a greater or less extort when low-rank, high-moisture coals are treated by oven-drying methods. The extent of this atmospheric oxidation has been described and evaluated by numerous workers. 7/In many respects, the problem of moisture determination in low-rank coals, those found in the United States and the high-moisture coals of Central Europe, is similar. Conversely, the problem of moisture determination assumes a different aspect when the coals of the eastern and the middle-west sections of the United States are considered. Present methods, the loss in weight gravimetic-type procedures, serve adequately to test these low-moisture coals. The determination of moisture in coals containing 20 to 40 percent water should be approached from a direct method rather than from an indirect gravimetic-type procedure because of the oxidative tendencies of these coals and the demonstratrated inability of a loss-in-weight technique to remove all the water in a given sample of coal."

May 1, 1953

By Robert G. Gibson, Joel D. Gibbons

Measurements and analyses were conducted of whole-body vibration aboard seven commercially available passenger and/or recreational vehicles: sedan; sport-utility vehicle (SUV); pickup truck; moving truck; motorcycle; all-terrain vehicle (ATV); and boat. The purpose of the testing was to measure and assess whole-body vibration exposure in a range of typical vehicle environments in order to gain understanding of typical exposure levels characteristic of activities of daily living. Vehicle models tested (and model year) were: Ford Taurus (1995); Jeep Cherokee Sport (2000); Toyota Tundra SR5 (2002); Ford F-350 (1997); Harley-Davidson Electra Glide Classic (2004); Yamaha Kodiak 400 4x4; and Steiger Craft Model 21 Montauk. All vehicles were tested with their standard factory-installed seats and were operated under a range of normal operating conditions and speeds typical of intended vehicle use. Methods The measurement, processing, analysis, and exposure assessment methods follow the guidance of generally accepted, national and international consensus standards relevant to the evaluation of whole-body vibration, including ISO 2631-1 [1] and ANSI S3.18 [2]. Seats were instrumented with low-mass triaxial accelerometers mounted in seat pads. Accelerometers used in the test are specified to have flat frequency response over the frequency range of 0.5 to 80 Hz, and all accelerometers were recently calibrated traceable to the National Institute of Standards and Technology (NIST). Seat pads were installed following guidance in the relevant standards [1, 2], with sensitive axes of the accelerometers following the standard coordinate system with respect to the seated occupant. (The x-axis represents fore-aft motion; the y-axis represents side-to-side motion; and the z-axis represents vertical motion with respect to the occupant.) Vibration data processing and analysis, including filtering, sampling, frequency-weighting, averaging, summation, and determination of basic and additional metrics followed procedures in the relevant standards [1, 2]. Digitized time series data were acquired and stored using a PC-based data acquisition system. Whole-body vibration exposure analyses were conducted via post-processing. During data processing, recorded periods of seat acceleration that were identified and verified as resulting from occupant-induced motion rather than vehicle motion were excluded prior to exposure analysis. The basic evaluation metric for whole-body vibration is the frequency-weighted root-mean-square (r.m.s.) acceleration, aw. The primary additional evaluation metric is the fourth-power

Jan 6, 2006

By J. W. Thompson, M. N. RICH

That there is wide interest in the preparation and properties of metallic zirconium and its salts is indicated by the many articles recently published in scientific and technical journals and the many patents issued. The compounds of zirconium have numerous important uses and more uses will doubtless be found. In the course of the special work on rare metals that were of military importance during the war, the authors of this bulletin were detailed to the Golden mining experiment station of the Bureau of Mines to prepare metallic zirconium and to investigate its properties. A number of investigations in recent years have indicated that sintered or coherent zirconium metal is very resistive to acids; that it can be used for electrodes, and it probably will find metallurgical uses. A steel containing zirconium has been proposed for use in armor plate and automobile parts, and nickel-zirconium alloys have been suggested for high-speed cutting tools and for cutlery. Numerous articles in scientific journals have recommended the use of zirconium oxide as a refractory, an abrasive, a pigment in paints, and as an opaquing agent in enamel ware. The salts have been used in the textile industry' as a mordant and also for weighting silk. When the authors began their investigation, they found it necessary to collect all of the available literature on the general subject of zirconium and its compounds. Pure salts could not be obtained on the market, and in order to get these, as a preliminary step to the preparation of the metal, the literature had to be classified and the methods of preparing the salts investigated. Also, there was much difficulty at first in making satisfactory analyses, and this phase of the work received careful attention. As it was necessary to begin with a historical review of the literature, such a review is given as Part I of this report, and a bibliography is included as Part IV. References to the numbered items in this bibliography are made throughout the text, the usual footnote references being omitted. Analyses of the products and conclusions as to their purity are given under the descriptions of methods of preparation. A table showing the properties of the amorphous metal, and another showing the properties of the coherent metal, will be found under appropriate headings in Part II. No attempt has been made in the historical review to discuss fully all the published information about zirconium and its compounds, but only such material has been assembled as has a direct bearing upon the present work. Considerable difficulty was experienced in collecting this material because of the confusion of terms by various authors who perhaps did not thoroughly understand the chemistry of zirconium.

Jan 1, 1921

By Jim Ploger, Peter W. Johnson

Bus drivers represent a large segment of the US transportation industry and research has shown an association between exposure to Whole Body Vibration (WBV) and the high rates of low back disorders. Impulsive WBV exposures have been recognized as a risk factor for low back injury and new guidelines exist for their measurement and assessment (ISO 2631, Part 5). Methods to accurately and better characterize the impulsiveness of WBV along with the temporal patterns of the exposures are needed. The development of a hardware and software system to measure continuous TWA and raw, impulsive WBV exposures and the design of a subsequent study are presented. Methods Using two Larson Davis HVM 100 as accelerometer amplifiers, small external batteries, and a Pocket-PC (PDA) with 1 Gb of compact flash memory, we can collect up to 16 channels of data for a full day 600 Hz. Tri-axial WBV exposures will be measured and characterized at the frame of the bus and at the driver/seat interface (seatpad accelerometer). Using a repeated measures design, 20 bus drivers will drive on selected routes which include both city streets and highways, and within and between subject components of variability and exposure determinants related to the bus, bus seat, the bus driver, and the route will be identified. Global Positioning System (GPS) data will also be collected and integrated with the WBV exposure data to facilitate the identification of the location, velocity and type of road associated with high average TWA and impulsive WBV exposures. This system may be used to develop administrative (alter speed and/or route of bus, systematically vary type of routes) and/or engineering controls (identify and trigger the need for street repair) to reduce high WBV exposures. Results Our portable Pocket-PC based data acquisition system is up and running and we can collect seven channels of WBV data (seat pan tri-axial accelerometer, bus frame tri-axial accelerometer and GPS data) continuously for a full shift. The software analysis of the data is complex but nearing completion. We have incorporated the vibration dose calculations from ISO 5321, Part 5 and have obtained a Matlab-based routine to appropriately weight the continuous signals. Discussion In summary, the measurement of WBV is complex but new technologies open avenues of collecting and assessing WBV exposures that were previously not possible. The standardization of impulsive WBV exposure assessment methods is needed to further the discipline and better enable comparisons across studies.

Jan 6, 2006

By Michael S. Contratto, Dave Marshall, Tom Brodersen

The European Union (EU) completed a new directive 2002/44/EC1 called the Physical Agents Directive (PAD) that establishes action and limit values for hand-arm and whole body vibrations. The directive specifies that: “…workers shall not be exposed above the exposure ‘limit value’.” 1 and “…once the exposure action values … are exceeded, the employer shall establish and implement a programme of technical and/or organisational measures intended to reduce to a minimum exposure to mechanical vibration and the attendant risks…” 1 The PAD limit value is effective for new machines starting July 6, 2007 and for used machines by at least July 6, 2010. These requirements apply to the users of machines, but machine manufacturers will be challenged to provide machines and information to help the users comply with the directive. Caterpillar manufactures machines with the goal of enabling our customers to comply with all regulations dealing with health and safety. Caterpillar designs all of our machines to provide a safe, comfortable and productive work environment. This study was to determine if seat suspensions could provide a reduction in the vibration environment experienced by operators of Caterpillar mid sized (<50,000KG) Track Type Tractors Methods Seat manufacturers were asked to provide seat suspensions that provide improved isolation over and above current seat suspension. Each supplier was provided with ride profiles and was asked to demonstrate the vibration reduction on a shaker table. Two suppliers provided suspensions that were compared with the current seat suspension in a field study. Three full factorial experiments were conducted. The first experiment was to evaluate overall suspension performance for four operations. The second experiment was to determine the benefit of the adjustable vertical damper at three different levels and the third experiment was to determine the effect of the fore/aft and side/side isolators. Six operators were used for the study. Acceleration was measured at the seat base and at the operator seat pad. Both the transfer function and the ISO 2631 RMS ride values were used to determine the seat suspension’s effectiveness of isolating the operator from vibration. A structured questionnaire was used to determine the operators’ subjective assessment of the seat suspensions. Results There was significant operator-to-operator variability in the vertical direction (>35%), however there was little variability in the fore/aft and side/side direction based on seat base

Jan 6, 2006

By John Paul Gries

This Bureau of Mines report reviews the mineral industry of the Black Hills area, including Butte, Custer, Fall River, Lawrence, Meade, and Penning- ton Counties, S. Dak.; and Crook, Niobrara, and Weston Counties, Wyo. It includes discussion of geological occurrence, processing, and potential of 27 commodities that have been produced from the nine-county area. The value of mineral production exceeds $70 million annually. Gold and petroleum account for two-thirds of the total, followed by clays, cement, sand and gravel, and rock. The combined mineral industries annually consume 268 million kilowatts of electrical energy, 933 million Mcf of gas, and 2 million barrels of fuel oil. Water consumption is about 10,000 gallons per minute. About 2,700 persons are employed on a year-round or significant part-time basis.

Jan 1, 1974

By R. Demont, A. Pranesh, S. Rakheja

Ethical concerns of in-vivo procedures and poor repeatability of non-invasive techniques have been major limitations in estimating vibration-induced spine loads through experiments. The biodynamic models of seated human body exposed to whole-body vibration (WBV) have evolved for defining the frequency-weightings, enhancement of human responses to WBV, and developing anthropodynamic manikins for seating assessment activities. The widely reported mechanical-equivalent models, solely based on through- or to-the-body biodynamic response functions, do not seem to resemble the biomechanical structure and do not yield information on the dynamic loading and deflections of segments of concern, namely the spine. On the other hand, biomechanical models with representative anatomical structure and anthropometry are being attempted to simulate segmental movements and the coupling effects, using Finite elements (FE) or multi-body dynamics (MBD) formalisms, which could provide important insights into the inter-vertebral forces [1]. While the FE models pose considerable complexities primarily related to characteristics of the bio-material properties, the MBD technique with discrete rigid bodies offers the flexibility to create multi-segment models with relative ease and lower computational cost. In this study, a preliminary multibody dynamic model of a seated human body exposed to WBV along the vertical direction is formulated using MSC/ADAMS software. The model validity is demonstrated by comparing selected responses with the available measured data. Methods The seated human is represented by nine rigid body segments, including: head, neck, thoracic and lumbar torso, pelvis, hands and thighs, as shown in Fig. 1. The rigid bodies are coupled through different rotational and translational joints, some of which are force elements to allow vertical translations and sagittal–plane rotations of the segments. The measurements of transmission of vertical vibration through-the-body generally require subjects to voluntarily maintain a vertical head position to reduce head-accelerometer orientation errors. The head–neck–shoulder joint is thus considered to be rigid. The shoulders are assumed to be rigidly attached to the thoracic segment. The torso is made up of three (upper, middle and lower) segments connected by visco-elastic revolute and translational joints to permit relative pitch and vertical motions. The forces and torques generated by the joints are derived assuming linear stiffness and damping properties, which were identified from published studies. The pelvis is connected to the rigid seat by similar elements representing the visco-elastic properties of the buttock tissues. The two thighs are rigidly connected to the pelvis, while the segment masses are chosen from the anthropometric data for the 50th percentile male subject. The initial model parameters for the joints were obtained from [2]. The model was analyzed to determine the force-motion relationship at the buttock-seat interface expressed in terms of

Jan 6, 2006

By N. Kumar Kittusamy

The purpose of this study was to assess the adequacy of the cab design and to determine the percentage of musculoskeletal symptoms among workers. A questionnaire was designed to assess demographics, work information, job history, and musculoskeletal symptoms in operators of heavy construction equipment. Information concerning equipment included design of the seat/chair, levers, pedals, bothersome vibration, quality of egress from the equipment, proper preventative maintenance and repairs, and age of the equipment. The body regions that were evaluated included the neck, middle/upper back, low-back, shoulder/upper-arm, elbow/forearm, wrist/hand, hip, knee, and ankle/foot. One hundred and eighty nine operators completed the questionnaire. The results indicate that these workers are at risk for developing musculoskeletal disorders, the need to perform a larger survey to further substantiate the outcome, and the need to quantify risk factors (i.e., whole-body vibration and static sitting postures).

Jan 1, 2003

By Gerald A. Muson, Fremont F. Clarke

"INTRODUCTION The use of scrap mica as an industrial raw material has grown rapidly during the past two decades. Demands by various industries for ground mica for use in the roofing, paint, rubber, plastics, and wallpaper trades as well as for less extensive uses in insulation, oil-well drilling, welding, pipeline enamel, decorative material, and for other purposes exceed present (1947) supplies.A small proportion of the raw material used comes from the Black Hills of South Dakota, where casual recovery has been practiced in the exploitation of pegnatite deposits for more valuable minerals. The annual production of scrap mica in the Black Hills for the years 1939 to 1946 is shown in figure 19. 4/Although small, this production of scrap mica materially augments the incomes of numerous operators.Volume production of mica would offer attractive opportunities for obtaining steady and more economical supplies of the rare minerals as byproducts. Appreciable supplies of beryl, lithia minerals, sheet mica, tantalite-columbite, and cassiterite could accrue. Furthermore, a stable scrap-mica production would complement the production of quality feldspar, for which the Black Hills pegmatites are noted, and would help balance the economy of pegmatite mineral production.Mechanical methods of separation are requisite to production of enough scrap mica to be generally profitable. Various phases of the characteristics end treatment of mica have been investigated by the Bureau of Mines. A bibliography of these reports is appended.In 1945 the Bureau of Mines conducted pilot-plant tests to recover scrap mica by selective screening of crushed pegmatite. More recently the problem has boon studied in the Pegmatite Research Laboratory to aid in developing technological methods by which scrap mica may be separated from crushed pegmatite."

Feb 1, 1949