Search Documents

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

By Mark I. Copeland

A study was conducted to determine if commonly used alloying additions or coating materials can prevent the formation of a liquid-copper phase during the reheating of copper-containing steels. If so, the tendency of such steels to surface-crack during hot-working might be eliminated. Steel specimens were scaled by heating them either isothermally or in a programed manner that simulated industrial furnace practice. Metallographic examination of the heated specimens showed that molten fayalite (Fe2Si04) completely prevented the formation of liquid copper at the surface. Fayalite, which melts at 2,200° F (1,205° C), was formed by internal oxidation of the silicon contained in the steel. By forming complex molten oxides, coatings of borax glass were also effective in preventing the occurrence of liquid copper at the steel surface.

Jan 1, 1972

By L. E. Cardwell

This publication contains routine analyses and related source data for 475 natural gas samples from 17 States and two foreign countries. Of this total, 454 samples were collected during calendar year 1971. The remaining 21 samples were collected during previous years, but releases granting permission to publish the analyses were not received until 1971. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Thirteen previous publications have presented the results of 9,427 gas analyses prior to 1971. The first three, Bulletins 486,5 576,6 and 617,7 contain analyses and related source data on 5,218 gas samples collected from

Jan 1, 1972

By R. L. Blake

The crystal structure of hematite, a-Fe203, has been refined as part of a continuing study of the behavior of phases in the Fe-O system during reduction and oxidation. Three-dimensional diffraction intensities were collected on two spherical single crystals of hematite with a semiautomated Buerger single-crystal diffractometer. The first crystal refined was a natural Elba hematite with minor impurities. The other, a synthetic crystal, was refined at the request of Mossbauer spectroscopy investigators concerned with impurities in the natural crystal. The structure has been refined with a least-squares program and the final structure for the natural crystal irradiated with CuKa-radiation gave a discrepancy factor (R) of 3.65 percent using 49 unrejected reflections of the 51 measured. For the synthetic crystal, using MoKa-radiation, the discrepancy factor converged to 2.8 percent using 95 unrejected reflections and was 3.3 percent for all 109 reflections. The structure model of Pauling and Hendricks has been confirmed with essentially no change in the iron coordinates and approximately a 5-percent change in the oxygen coordinates. Selected interatomic distances and angles were calculated as were anisotropic temperature factors.

Jan 1, 1970

During the second quarter of 1983, the economic recovery showed further strength abetted by the performances of consumer spending, residential investment, and the slowing down of inventory reductions. Real gross national product (GNP) increased from the first to second quarter at an annual rate of 9.2 percent, compared with 2.6 percent from the fourth quarter of 1982 to the first quarter of 1983 and an overall 1.9- percent decrease in 1982. Total industrial production increased 1.8 percent in July, and productivity as measured by output per man-hour increased 1.3 percent between 1982 and the first quarter of 1983 (table 1). Especially noteworthy .was the performance of real consumer durable goods expenditures, which increased at an annual rate of 32.0 percent from the first to the second quarter (about half of the increase consisted of automobile sales) and real consumer spending, which increased between these periods at an annual rate of 9.7 percent. Residential investment increased at an annual rate of 76.1 percent between the first and the second quarters,1/ and private housing starts by about 38,000 units in both March and May.

Jan 1, 1983

By R. H. Bedford, F. T. Johnson

"In California the history of tin mining began in Riverside County in 1853, with the discovery of the Temescal deposit. This deposit remained the only one with a production record until recent small shipments were made from Kern and San Bernardino Counties.According to the California State Division of Mines, Temescal's total output has been about 125 tons of tin, all of which was produced in 1891 and 1892. It was idle from 1892 to 1928.An extensive but unsuccessful development campaign carried on in 1928 and 1929 by the American Tin Corp. produced only half a ton of the metal, and the property again was idle until 1943, when an attempt to resume operations proved unsuccessful. After 1929 no production is recorded from California until 1944 end 1945, when small shipments of sorted ore from Kern County returned about 2 tons of tin and 1-1/3 tons was recovered from sorted ore and concentrates from San Bernardino County. The total output of tin from California has been less than 150 tons, and less than 4 percent of this was produced in the last 50 years, in spite of numerous attempts during that period to promote tin mines,So marked a scarcity of a metal essential in war makes any occurrence interesting. When some prospects were reported to the Bureau of Mines in July 1942, in a new field 10 miles east of Gorman, they were at once examined and the preliminary exploration by the owners closely followed. Eventually one was explored by bulldozing end diamond drilling as a joint project by the Bureau of Mines and the Geological Survey.To supplement this joint project, the authors undertook independently a general survey of tin in California - a survey designed to check reported occurrences and to bring their status up to date. In this work, the 37 places described in the text and spotted on the accompanying map, (fig. 1) were visited end sampled. Although traces of tin were found in many pieces, nothing that suggested a tin mine was found anywhere, and it is difficult to base much hope for appreciable future tin production upon anything found thus far in California."

Apr 1, 1946

By J. L. Howell, D. E. Pollock, A. B. Cecala, A. D. O’Brien

Dust from worker,s clothes has been shown to be a problematic source of personal dust exposure. A recently completed effort between NIOSH and the Unimin Corporation has resulted in a quick and effective way to clean worker clothing. The process involves a booth under negative pressure with an air spray manifold to supply compressed air to blow off the dust from the clothing. The overall system is designed to meet MSHA and OSHA requirements. Results of field testing indicated that the manifold cleaned the clothes 10 times faster and removed 50% more dust than cleaning methods used by workers today.

By R. Larry Grayson

In the October 1998 issue of the Holmes Safety Association Bulletin, NIOSH authors Mark Stephenson and Carol Merry wrote the article Hearing loss among miners and measures to protect hearing, which focused on the extensiveness of hearing loss among miners and the use of hearing protection to prevent hearing loss. While the primary importance of engineering controls in preventing hearing loss was discussed, since miners do not generally have control over their work en­vironment or assignments, the article focused on the importance of consis­tent use of hearing protection. In this article, all aspects of a compre­hensive approach to the prevention of hearing loss in miners will be covered. The discussions will do the following: ? describe application of the hierarchy of controls in preventing hear­ing loss in miners, ? give an example for each type of control measure and its impact, ? explain the major provisions, be­yond the hierarchy of controls, of the recent NIOSH document en-titled Criteria for a Recommended Standard: Occupa­tional Noise Exposure, Revised Criteria 1998 relative to a hearing loss prevention program, and ? summarize important points on control of noise exposure for every miner to remember, equipment in most facets of operations. Miners are well aware of noisy areas in or around equipment, icluding extraction machinery such as draglines, power shovels, longwall shearers, and continuous mining machines; powered haulage equipment such as load-haul-dumps, shuttle cars, large trucks, and continuous haulage units; roof bolting machines; jackleg drills and stopers; auxiliary equipment such as compressors, fans, and pumps; size reduction equipment, etc. They are not well aware of the insidious nature of pro­gressive hearing loss, which is per­manent, but they are generally aware of what levels of noise are hazardous and what measures can be taken to reduce their personal noise exposure. Behaviorally, however, there are many reasons why miners choose not to use hearing protection faithfully.

Jan 1, 1998

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to 5-ton pieces, a 150-ton batch-type retort was designed and constructed at the Bureau of Mines Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11 ½ feet inside diameter, and is supported in a 95-foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, was used as the test shale. To date, 11 runs have been completed, and the results of the last 10 of these are reported. The effects of oxygen content of the retorting gas and the superficial gas velocity of the retorting gas on oil recovery from a column of mine-run oil shale were studied. In one run, the average particle size of the shale was substantially increased to determine its effect on oil yield. Oil recoveries ranged from a low of 39.3 to a high of 65.8 volume-percent of Fischer assay.

Jan 1, 1974

By Rudy J. Matetic

Over-exposure to noise remains a widespread and serious health hazard in the U.S. mining industries despite 25 years of regulation. Every day, 80% of the nation’s miners go to work in an environment where the time weighted average (TWA) noise level exceeds 85 dBA and more than 25% of the miners are exposed to a TWA noise level that exceeds 90 dBA, the permissible exposure limit (PEL). Additionally, MSHA coal noise sample data collected from 2000 to 2002 show that 65% of the equipment whose operators exceeded 100% noise dosage comprise only seven different types of machines; auger miners, bulldozers, continuous miners, front end loaders, roof bolters, shuttle cars (electric), and trucks. In addition, the MSHA data indicate that the roof bolter is third among all the equipment and second among equipment in underground coal whose operators exceed 100% dosage. A research program was implemented to: 1) determine, characterize and to measure sound power levels radiated by a roof bolting machine during differing drilling configurations (thrust, rotational speed, penetration rate, etc.) and utilizing differing types of drilling methods in high compressive strength rock media (>20,000 psi). The research approach characterized the sound power level results from laboratory testing and provided the mining industry with empirical data relative to utilizing differing noise control technologies (drilling configurations and types of drilling methods) in reducing sound power level emissions on a roof bolting machine; 2) distinguish and correlate the empirical data into one, statistically valid, equation, in which, provided the mining industry with a tool to predict overall sound power levels of a roof bolting machine given any type of drilling configuration and drilling method utilized in industry; 3) provided the mining industry with several approaches to predict or determine sound pressure levels in an underground coal mine utilizing laboratory test results from a roof bolting machine and 4) described a method for determining an operators’ noise dosage of a roof bolting machine utilizing predicted or determined sound pressure levels.

Jan 1, 2006

By I. L. Nichols

The Bureau of Mines is investigating vanadium recovery from various domestic resources. A low-grade carnotite ore sample containing 0.34 pct V20S and 0.04 pct U30S was leached, and the results were compared with those of similar leach tests using a mill-grade sample containing 1.26 pct V205 and 0.19 pct U308. Experiments on the two ore samples included agitation leaching, pugging, salt-roast leaching, and autoclave leaching. None of the leaching methods investigated showed any significant advantage over another except autoclaving, which reduced the leach time but at the expense of greater acid consumption. Typical of the experimental results attained are the data gathered from the agitation leaching tests. Agitation leaching of the mill-grade ore with 100 lb/ton H2S04 resulted in extractions of 94 pct U308 and 33 pct V205. To increase the vanadium extraction from 33 to 91 pct required concentrations of 300 lb/ton H2S04 and 10 lb/ton NaC103. Complementary agitation leach tests on the low-grade ore required 200 lb/ton H2S04 to extract 94 pct U308, and 300 lb/ton H2S04 and 10 lb/ton NaC103 to extract 90 pct V205.

Jan 1, 1983

By D. Bienstock

To develop a rugged catalyst capable of withstanding hydraulic attrition resulting from the oil-circulation process for synthesizing liquid fuels, use of an iron catalyst containing an active coating surrounding an inert solid core of metal was investigated. This massive-iron catalyst in the form of steel shot and lathe turnings was activated by partial oxidation with steam at 600° C, impregnated with alkali, and reduced with hydrogen at 450° 6. The massive-iron catalysts were resistant to oxidation and spalling, and a 6-month catalyst life was attained. Higher operating temperatures could be employed than with fused iron oxide catalysts, resulting in greater gasoline yields. Because the lathe turnings pack with void volumes of 70 to 90 percent, it has become possible to employ a fixed bed without the danger of cementation that occurs with fused iron oxides.

Jan 1, 1963

By Anderson Dana

THIS PAPER describing methods and costs of mining and preparing gravel and sand for market at the Port Jefferson plant of the Seaboard Sand and Gravel Corporation, is one of a series of articles on gravel and sand mining, prepared for and published by the U. S. Bureau of Mines, which is designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs, It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical [ ]

Jan 1, 1932

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

By B. Gillenwater

This report describes the results of investigations into four specific areas related to trolley wire power distribution systems in coal mines. These are: 1. Partially insulated (shielded) trolley wire 2. High-speed insulator fault detectors 3. Dual-wire trolley systems 4. Insulator failure indicators. Prototype devices or designs were developed in each area. In addition, a brief survey was made in an attempt to assess the Future of mine trolley systems, and data was collected and reviewed in an attempt to analyze the nature of trolley wire related accidents. Other options for decreasing the risks associated with trolley systems that arose .during the study are briefly described in appendices. These include insulating equipment and miners from return and/or energized conductors and use of a segmented trolley wire with local control of current delivering capability.

Jan 1, 1981

By Dale R. Spangenberg

This Bureau of Mines Information Circular on phosphate is one of a series of minerals availability commodity directories. Nonconfidential information from the Minerals Availability Program data base covering 148 domestic and 103 foreign phosphate properties and deposits has been abstracted for use in this directory. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operational information.

Jan 1, 1983

By William C. Cooley

This report includes a review of all relevant data on underground hydraulic coal mining technology collected during Phases I and II of the contract. Data collection and analysis procedures are discussed. Information is included on past and existing underground hydraulic coal nines in the USSR (27 mines), Poland (1 mina), Germany (1 mine), Japan (1 mine), Canada (1 mine), China (1 nine), as well as underground tests conducted in the United Kingdom (2 mines), and in the United States (5 mines). Data is also included on Czechoslovakia and New Zealand. In all operational hydraulic mines, coal is transported underground in flumes. In most cases, bituminous coal is broken by monitors with nozzle diameters larger than 16 mm (0.63 in.) and jet pressures of 50 to 125 atm (710 to 1780 psi). Technical design and performance data are included on all key types of equipment and components which have been developed for, used in, or which could be potentially be used in hydraulic coal mining systems. Data sheets are presented on 180 types of equipment, divided into 24 major categories. Where available, sketches, drawings, photographs, and price estimates are included. Data are included on pitching coal seams in the United States which potentially can be mined by hydraulic methods. Preliminary conclusions are presented, subject to revision as a result of economic feasibility studies to be completed during Phase III. An outline is presented of the final report, which will include economic studies and recommendations for research and development.

Jan 1, 1975

From the time of its establishment in 1910, the Federal Bureau of Nines has studied the carbonization of coal, and a considerable part of this effort has been devoted to investigations in the so-called low-temperature carbonization range, 450° to 700° C., in which there is minimum decomposition of primary products and maximum yield of Liquids - a yield two to threefold the amount produced in high-temperature carbonization at 900° to 1,200° C, The solid residue, char, or coke, produced in low-temperature carbonization is 70 to 80 percent of the coal charged and may be used directly as a smokeless fuel or for blending with coals to produce metallurgical coke, Although some thought was given to the use of tar and to the illuminating value of gas derived from lm-temperature carbonization, the main emphasis in early work of the Bureau of Mines was on the preparation of smokeless fuel, especially for home use, For example, a carbonizer was designed and operated for making char and briquets from North Dakota lignite without recovery of by- products; however, the shortage of high-temperature coal-tar products in the United States during World War I had already indicated the potential usefulness of low-temperature tar.

Jan 1, 1959

By T. L. Muldoon

The bagging of dry pulverized products using fluidized air packers creates severe respirable dust problems in many surface mining operations. During bag filling, excess air and product blows by the bag valve/nozzle interface. After bag ejection, dust blows out of the bag valve. During conveying and handling dust is released from the bag valve and dirty bag surface. Overexposure of the bagging machine operator and bag handlers is common. This report describes the development and testing of a new dust control system for bagging machines. The system features a new bag clamp design to reduce product blowby during filling. A controlled vacuum system removes excess air from the bag before ejection, eliminating the problems after bag ejection and during conveying and handling. The system has shown significant reductions in dust exposure for both bag machine operators and bag handlers. These reductions are achieved with no significant effect on total mill productivity.

Jan 1, 1985