Search Documents

By Donald Little, Larry Unger

This paper will give a detailed insight into hard rock, large diameter surface blasting including some practical tips to improve blasting practices. These tips will be non-technical, of the nuts and bolts type, intended to help the man in the boots. The paper will begin with the importance of communication between the engineering department and the blasters. What looks good on the mine development map might not blast very well. Tight inside corners, 90 degree outside corners, too few rows; are a few of these problems.

Jan 1, 2006

By David A. Smith, B L. Jr Lindsey

Arkansas bauxite varies enormously in its consistency and composition which makes blasting a very difficult operation. Blasting rounds have to be designed based on each particular mine's ore characteristics. The variances are so great in some mines that blasting procedures have to be changed almost daily.

Jan 1, 1979

By Gregg R. Gitschlag

There are more than 4,000 oil and gas structures present in the U. S. Gulf of Mexico. Approximately 100 structure removals occur each year and 66% of these are removed with explosives. From 1993-1995 an intensive study was conducted on the fish kill resulting from the explosive removal of 6 platforms off the Louisiana coast in water depths from 14-28 m (45-92 ft). After explosives were detonated, all floating fish and a sample of the dead fish which sank to the sea floor were collected.

Jan 1, 1997

By Yuji: Wada Ogata, Kunihisa Katsuyama

It is well known that a compressed stress wave reflects at the free face, it propagates to the backward as a tensile stress wave, and cracks grow when the tensile stress becomes the dynamic tensile strength. The behavior of these cracks has been discussed through the observation of the dynamic photoelastic high speed photography.

Jan 1, 1993

By Adrian J. Moore, Alan B. Richards, Rob Evans

Air and ground vibration from blasting is influenced by the delay pattern that is used. Wavefronts from blastholes fired in a blasting pattern can combine in certain circumstances to give increased blast vibration levels. A simple computer model has been developed which shows the combined effect of wavefronts from a multi-hole blast and identifies if wavefront reinforcement occurs, and permits delay patterns to be designed which will avoid or reduce wavefront reinforcement.

Jan 1, 1994

By J W. Edl, F C. Wu

In instrumented model rock blasting experiments in granite blocks, best fragmentation results were obtained when delays between holes were 1 to 2 milliseconds per ft. of burden and when a rectangular shothole pattern was used with spacings larger than the burden. Effective fragmentation in multiple hole blasts seemed to depend primarily on the full development of the crack network around each hole before the charge in the next hole was detonated. The test results showed that simultaneous or almost simultaneous initiation of shotholes in bench blasting resulted in poor fragmentation.

Jan 1, 1975

By J S. Kuszmaul

The economic development of modified in situ oil shale retorting will benefit from the ability to design a blasting scheme that creates a rubble bed of uniform permeability. Preparing such a design depends upon successfully predicting how a given explosive will break rock. Numerical models are used to make predictions of the extent of damage caused by an explosion.

Jan 1, 1985

By Philip Barnhard, Lyman G. Bahr

By recording the arrival time of a pipe wall at evenly spaced intervals in a plane perpendicular to the pipe axis, application of the equations of motion permits calculation of the pressure of the explosive acting to accelerate the pipe wall. Data observed from various non-ideal explosives are presented, together with values of pressure to be expected from thermodynamic calculations.

Jan 1, 1981

By Zhou Jiahan Wang Feng

This paper introduces the mechanism and the operating process of dike building by silt squeezing blasting. DBSSB (dike building by silt squeezing blasting) has the following advantages: shorter construction period (the construction period is decided only by the speed of rock materials filling)greater consolidation of the body of the dike, more structural stability, smaller settlement. Therefore by conventional standards the same dike can be designed with a smaller cross section than other construction methods, and at a reduced cost when enough rock materials can be provided in site.

Jan 1, 2006

By Lyall Workman, Jack Eloranta

In this paper results of drill to mill research are examined. It is found that several descriptors of blasting results change when the powder factor is increased. Fragmentation shifts toward a finer distribution. The Bond work index decreases and the product of the t10 model breakage parameters increases. Both of these indicate more softening of fragments. There is research that found large differences in bond work index and other studies that find a much smaller decrease. Even at the lower decrease, however, some savings in energy cost can accrue in hard ores ground to small size.

Jan 1, 2009

By Mark S. Stagg, Steven V. Crum

The Bureau of Mines is conducting research to develop methods to control fragmentation and improve productivity in surface mine blasting. As part of this research, PRONT02D, a two-dimensional finite element computer program developed at Sandia National Laboratories, was employed to model the fragmentation produced from RS-50, a single hole, reduced scale bench blast in a massive dolomite. The fragment size distribution obtained from the computer simulation was calculated using a submodel that utilizes the crack density and nominal flaw size values computed by PRONT02D.

Jan 1, 1989

By Jack Eloranta

This paper documents the relationship between material handling and processing costs compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this case study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong, inverse correlation with powder factor (lbs powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

By Shih Wen Wang, Ronald R. Rollins

A blast casting model is proposed to predict the burden velocity in bench blasting. This blast casting model is the first theoretical model that 1) explains the throwing procedures and mechanisms, 2) uses the explosion pressure as the primary source in throwing rock fragments, 3) applies them to field conditions successfully. Also the predicted burden velocities are based on the rock properties, the explosive properties, and the drilling and initiation patterns. This blast casting model is programmed into a computer software "ROCKFRAG". The comparisons between "ROCKFRAG" predicted values and two field test data are in good agreement.

Jan 1, 1992

By Quian Liu

The problem of cross-hole explosive malfunctioning in rock blasting (including sympathetic detonation, desensitization and cut-offs) is a function of delay and spacing in a blast which should be designed to avoid such occurrences. On a delay-spacing chart, the phenomenon of explosive malfunctioning is explained by dividing the chart into different regions, while the shape and size of each region could vary from one explosive to the other. Over seventy blasts have been carried out at the CANMET Experimental Mine to identify the malfunctioning characteristics of specific emulsion, water-gel and dynamite explosives. In each experiment, two parallel blastholes, 32 mm in diameter and 1.7 m deep, were drilled downwards in an underground drift.

Jan 1, 1994

By J R. "Dick" Daniel

In the fall of 1988, The Cannon mine decided to investigate a central blasting system based on conventional electric blasting detonators being used to initiate rounds primed with Nonel detonators. The advantages of this hybrid detonator system were viewed as being safety and cost effectiveness. A study was done reviewing the safety aspects of utilizing a permanent blasting line installed throughout the main haulage drifts to a central blasting station located at the mine portal. The study addressed the following potential safety hazards: radio frequency induced current, stray current from both electrical utilities and transmission lines, galvanic and electrostatic sources of extraneous current.

Jan 1, 1989

By John M. Bolger, Keith E. McMaster

Excessive salt fines are undesirable in underground salt mining as they are considered a costly waste by-product. This paper describes an extensive explosive application program conducted at The Canadian Salt Company Ltd, located in Pugwash, Nova Scotia, Canada. The prime objective of the program was to reduce the quantity of fines generated from this company's underground production blasts. The program was known as the "The Fines Reduction Program".

Jan 1, 1996

By Richard Scales, Giles Hellyer, Ian Travers, Dean French, Peter Bellairs

"The Mt Whaleback iron ore mine is located in the Hamersley Province situated about 1OOOkm to thenorth of Perth, the capital city of Western Australia. A small but significant portion of the waste in Mt Whaleback presents problems due to its ability to react with normal commercial bulk explosives resulting in premature detonations, two of which occurred at the mine in 1983 causing great consternation as well as disruption to the mining operation. The techniques and procedures developed to overcome this problem were based on the use of tough durable, acid and heat resistant liners to provide a physical barrier separating the explosive from the rock togetherwith the development of an accurate down the hole remote temperature logging technology. The liner technology was developed due to the inability to produce a reliable inhibited ANFO despite exhaustive mine based testwork."

Jan 1, 1999

By P. Katsabanis

Numerical modelling was used to examine damage in wall control operations. Decoupled charges appear to create larger damage zones than fully coupled low density charges with similar charge distributions: Air was shown to be a very efficient coupling medium, while water coupling resulted in significant damage. However, Mach stems are formed when air is used as a decoupling medium, leading to compression of the charge ahead of the detonation wave. Air decked charges generate two damage zones, one close to the charge and another close to the air-deck/stemming interface, where pressure pulses are reflected. The extent of the latter depends on the length of the air-deck.

Jan 1, 2001

By Paul V. Sterk, James Wieser

Mining in underground situations requires constant change due to changing ore bodies and economics. The Homestake Mine in its 122 years of existence has gone through numerous changes due to these factors. Recent sustained low prices in gold and ore bodies that are smaller or within mined out areas have forced the mine to reevaluate how these ore blocks will be mined. This paper will describe the design, drilling, and blasting of a complex ore block using the blind raise uphole bulk mining method.

Jan 1, 1999

By John Manka

Emulsion manufactures often spot buy the diesel fuel used in their fuel phases from various sources. Because their diesel source changes, there can be large fuel variation which may affect the quality of the resulting emulsions. This paper shows that the diesel fuel used in manufacturing emulsion explosives has a significant impact on emulsion stability and that the fuel additives dosed into the diesel fuel as it is made also have an impact on the emulsion characteristics and stability. We found that fuels with higher distillation ranges improve emulsion stability. We also found that while none of the diesel fuel additives affected the initial formation of the emulsion, some fuel additives did affect the characteristics and stability of the emulsions as measured by emulsion viscosity, droplet size, high and low shear testing, bin storage testing and freeze thaw cycling.

Jan 1, 2002