Search Documents

By Marlyn G. King, Robert L. Martin

Blasting activities in all four pits at Thunder Basin Coal's Black Thunder Mine are focused on cast blasting. With widths varying from 190 feet to 265 feet and bench heights varying from 90 feet to 175 feet, casting efficiencies vary with different geometry's. For example, the percent cast to final in the 200 foot pit is on the average higher than the 270 foot pit. The powder factors are somewhat higher in the narrower pits, thus increasing the cost of blasting. This leads to a very detailed look at the actual benefit of cast blasting and the associated cost of these benefits.

Jan 1, 1995

By John F. Mitchell

Large production blasts involving many series in parallel have long been a source of complication. When speed and accuracy are most necessary in blast preparation an efficient and precise method of wiring is required. After loading a large number of holes and being pressured for time, due to lack of daylight, equipment shutdown, etc., an effective hook-up plan can eliminate many last minute problems. It is the intention of this paper to offer a simplified wiring proceedure which when employed can save precious time and encourage efficient and economical utilization of blasting personnel and material.

Jan 1, 1976

By Karl E. Burgher

Accidental explosions occur throughout the world. They can happen at chemical plants, fireworks plants, grain depots, or as a result of collisions involving volatile or hazardous chemicals. It is interesting, as we know as blasters, that we can take two very harmless products and mix them under certain conditions and produce a violent explosion. It is often very difficult for the investigator to determine the magnitudes of blasts after the fact. However, an estimate must be made to settle vibration and airblast damage claims. The blasting consultant or technical representative is often called upon to act as an expert to mitigate these claims.

Jan 1, 1993

By Robert E. Miller

Mass blasting of open stopes and pillars is a normal operating practice at Isa Mine. Three main parameters are used to classify the types of mass blasts. These are type of explosive used, blasthole diameter and system of initiation. Both electric and non-electric initiating systems are currently employed. The advantages gained by large firings are many. More efficient utilization of manpower, due to the concentrated and continuous charging, is achieved. There is no requirement for men to re-enter areas where localised ground conditions may have deteriorated and exposure of ringfirers to stope voids is reduced.

Jan 1, 1980

By Donald H. Matthews

The Society of Explosives Engineers is an international organization of over four hundred members involved in the explosives industry, with most members being active in the United States. The regulations imposed by regulatory agencies on the explosives industry have drastic effects far beyond the industry. Since explosives are used in mining, manufacturing, construction, entertainment, and art, all phases of man's activities, including fundamental needs for survival, are affected by how efficient the industry uses explosives. We, as members of SEE, must be sincerely concerned with both the quantity and quality of government regulation, and this paper spells out some of the problems caused by regulations and offers a solution.

Jan 1, 1980

By Thomas P. Dowling

Historically, laws controlling the manufacture, sale, transportation and storage of high explosives and regulations governing the use of explosives were formulated to prevent accidents or eliminate incidents that might jeopardize public safety. Many of the original laws and regulations regarding classification of explosives and blasting materials, tables of distances for separation and/or isolation of explosives, construction of storage magazines and methods of blasting were based upon empirical data, field experiments or scientific facts. During the past few years, however, it appears that some of the explosive laws and blasting regulations introduced and/or enacted by federal, state and local agencies seem to be based more on political expediency than on factual information or technical data.

Jan 1, 1976

By Charles B. Ingram, Neil E. Gehrig

The development of water gel explosive products has been the single most important development in explosive research and development since the invention of nitroglycerine and dyne-mite many years ago. m e Explosives Department of Gulf Oil Chemicals Company has been engaged in the research, development, manufacturing an marketing of slurry explosives and blasting materials for over twenty years. Explosive research and development is being carried out at the Jayhawk Technical Laboratory and the Underwater Testing Facility near Pittsburg, Kansas. There are fourteen manufacturing facilities geographically located around the country to serve the mining, quarrying, and construction industries with a complete line of explosives, blasting agents, and accessories. This paper discusses the Gulf slurry products, their properties, and uses.

Jan 1, 1977

By Dale S. Preece, Stephen H. Chung

"In bench blasting, the distribution of loaded explosives with respect to the burden rock has strong effects on digging especially at the toe area. Blast design often focuses on other results such as percent-cast or fragmentation, sometimes leaving a diggability problem at the toe of the blast that is not discovered until excavation. A method for assessing the influence of blast design on diggability has been developed. This method relates the kinetic energy and rock displacement experienced by the material in the muckpile to its diggability. Simulation of the blast along with the calculation of kinetic energy and diggability is done with the discrete element computer program DMC_BLAST(DMC: Distinct Motion Code)."

Jan 1, 1999

By Q Liu, P D. Katsabanis

Dust explosions in underground sulphide and oil shale mines result from the detonation of explosives in the blasting operations. Explosive composition, oxygen balance, priming and ideality of detonation were examined theoretically and experimentally in the presence of reactive sulphide dust. It was found that the temperature as well as the chemical composition of the gaseous products of detonation are the controlling parameters related to the explosive. Non aluminized, oxygen balanced emulsion explosives were proven to be relatively safe, while explosives creating combustible products were proven to be extremely dangerous due to the secondary flame they generate. Since a large number of dusty orebodies are often very friable, low density emulsion explosives are also examined for application in production blasting.

Jan 1, 1991

By Virgil L. Lewis

On September 7, 1994, a Burlington Northern coal train crashed into a parked train in the downtown Gillette, Wyoming rail yard. I would like to address two issues in regards to this accident. One, a slide presentation of the damage created by the accident and the resulting required clean-up and two, a simulation of "what if" had there been an explosion during the course of the crash.

Jan 1, 1996

By J R. Brinkmann

The South African gold mining industry presently uses four different types of explosives in stope blasting. There is general agreement that the type of explosive has considerable effect on Important blasting results such as the degree of rock fragmentation, the intensity of damage to surrounding rock, and the success of break-out at the toe of the hole.

Jan 1, 1989

By W. Fourney

In the late 70’s and early 80’s in conjunction with other oil and gas well stimulation studies, personnel from the Dynamic Effects Lab performed model testing to demonstrate the effectiveness of utilizing an open section of borehole just before a plug. We called the process stem induced fracturing. The open section beneath the stem was used to increase the pressure magnitude and spread out the duration of the pressure pulse. This technique was later utilized to by Frank Chiapetta (1) in the fracture and fragmentation of rock in quarry blasting situations. He called his technique air deck blasting. In fact, Frank found that the Russians had previously discovered the same technique. There is currently interest in utilizing air deck blasting with an open section of hole beneath the explosive at the bottom of the bore hole to better remove the toe in a fragmentation shot. This paper reviews the development of stem induced fracturing and then describes a series of model tests conducted to measure borehole pressure at points along a borehole when an explosive charge is detonated at the midpoint of the borehole. Tests were conducted in both stiff boreholes (aluminum) and less rigid boreholes (PMMA-Plexiglas). Pressure time profiles were measured at the charge site, midway between the charge and the bottom of the hole, at the stemming at the top of the borehole, and at the bottom of the borehole. Crack initiation sites and crack propagation were also determined in the PMMA models. Some high speed pictures were taken of the event in the PMMA.

Jan 1, 2006

By Paul Ross, Harry Burchett, Lou Case, Calvin J. Konya

"The Cumberland River in Harlan, Kentucky has flooded the town for numerous years. TheU.S. Army Corps of Engineers funded a project to divert the river. The project consisted oftunneling through a mountain to divert the river. The approaches to the tunnels requiredcontrolled blasting to create noses to help channel the water and debris into the tunnels.The geologic structure was such that conventional presplitting techniques were notproducing the desired results and were causing severe backbreak. Replacement of the rocknoses with concrete would cost about a million dollars; and therefore it was important tosave them if at all possible. Blasting techniques were developed which allowed the projectto be successfully completed. This paper will discuss the case history of the controlledblasting procedures."

Jan 1, 1993

By Justus Deen, Paul Sterk

Overbreak into the wall rock of a development drift leads to the inevitable need to rehabilitate a drift. Moreover, overbreak in a production heading can lead to external dilution and lower ore grades. Both of these factors are critical to bottom line costs of underground operations today. The geology of the Homestake orebody makes this an even more complex problem. For over fifteen years the Homestake Mine has attempted to implement perimeter blasting techniques that are both safe and cost effective. Many practical perimeter methods and products have been tested including air decking; low density emulsions; various types of stick powder; various decoupling media including rope, low density ANFO, polystyrene ANFO, salt based ANFO, and various grain detonating cords up to 200 grain.

Jan 1, 1997

By Michael E. Kovach

This discussion is an overview of an approach to drilling and blasting angle holes at Martin Marietta Aggregates. Method of determining burdens, hole depths, angle settings and explosive selection will be discussed in detail with an emphasis on safety and production. Such techniques and methods involve the use of hand-held surveying instruments such as the Abney level, pocket transit and inclinometer along with measuring tape and burden pole. An interesting method developed by Oscar Banfield a retired Martin Marietta and E. I. duPont engineer, for setting the proper angle on a drill will also be presented. This treatise is a discussion of the use of simple yet important tools and techniques a blaster should use to resolve both routine and complex problems encountered during quarry blasting operations.

Jan 1, 1992

By Qi Jingyue, Wang Zhongquian, Yang Nianhua

Qinling Tunnel is the longest tunnel in China. The rock stratum is very hard rock - intact mixed gneiss. At the beginning of the construction, drift-pilot excavation is very costly due to the use of regular drill and blasting methods. After tests on the acoustic impedance match between rock and explosive, watergel explosive, which has a high velocity of detonation and high brisance, has been used for hard rock blasting. In addition, different cut plans have been compared. It was found that four-large-hole cut is the most effective. And the number of drillholes and specific charge cut down and the average advance reaches more than 94% of the blastholes depth. Thus, the difficult problem of hard rock blasting in drift pilot is successfully solved, while safe and quick construction is guaranteed.

Jan 1, 1998

By Justus Deen, Paul V. Sterk

Through the 119 year history of the Homestake Mine various methods of raise mining have been used, these include conventional, bored, and drop raises. These raises provide passage for men and supplies, provide ventilation, transfer broken rock from level to level, and serve as emergency escapeways. As the 1980s came to a close, many of the larger ore bodies in the mine had been mined out. This has resulted in many crown pillar situations that required a method to mine them. In addition, the Homestake ore body also contains numerous ore reserves that have short vertical height. The ore itself can be from vertical to 50 degrees in dip. Due to the high cost of drift and ramp development many of these ore bodies are sub-economic using conventional mechanized cut and fill mining.

Jan 1, 1996

By Dale L. Ramsey

The Pinkerton Tunnel Open Cut Project is part of the National Gateway Clearance Initiative improvement project to achieve a minimum of 6.4 meters (21 feet) of vertical clearance along CSX Transportation rail corridor so that double-stacked intermodal railcars can be transported between Mid-Atlantic States and their ports to Midwest Markets in the U.S.

Jan 1, 2014

By D G. Dressler, Paul Yeager

A previously little-known facet of seismic frequency spectrum analysis is gaining significance. The frequency spectrum of seismic waves promulgated from blasting is a significant factor in causing blasting complaints and threshold (architectural type) damages.

Jan 1, 1987

By Terry Matts, Henry Heidrich, Cluny Randell, Carl Kottmeier

Until 1990, all production of asbestos ore at Cassiar was by open-pit methods. With the impending exhaustion of open-pit reserves, a decision was made in February 1988 to continue mining underground, using the block-caving technique.

Jan 1, 1992