Search Documents

By S. V. Petrov

Oxidised ores possess a significant share among raw materials which are treated by traditional plant technology. As usual, the chemical composition of these ores is rather simple. They can be treated by standard cyanidation. In this case, the resulting wastes have an alkaline reaction. Their toxicity (in case of ROM ores treatment) is mainly due to the presence cyanides and thicyanades. The tails are dexotified before disposal. However, chemical reagents used cannot provide a complete removal of toxic matters. In this case, this disposal poses a real problem because these tails contain a significant amount of CN and SCN and their behavior during a long disposal should be studied. A sample with a simple composition taken from cyanidation tails was studied. The sample presents itself the quartz low-grade sulfide gold-bearing ore. Sulfide sulfur content is 0.15 per cent,and heavy metals content is 0.023 per cent. Method of testing is described further. The samples were tested under moderate and subarctic climates based on the difference in temperature, moisture and the degree of oxygen saturation of air. The pH of water extract, which was prepared using distilled water, was also determined besides measuring the concentration of cyanides and thiocyanates. This demonstrates the stability of sulfide-bearing minerals in the disposed tails. The tests time was 820 days. It was found that the alkalinity of the samples tends to lower under oxygen-containing conditions in proportion to temperature increasing. Under conditions without oxygen, the pH lowering is minimal. Mineralogical and chemical properties of the ore material give positive alkaline balance during testing. The solid sample contains enough alkaline agents to compensate dangerous to the environment reactions of sulfides oxidation.pH value maintaining under alkaline conditions witnesses to the possibility of a safe disposal of this tails type. The largest amount of cyanide is removed under acid-containing conditions at positive temperatures. The higher the temperature is, the more intensive destruction is. At the moment, of finishing the tests at 20ºC temperature, the residual concentration of CN- was 0.06-0.10 mg/L, at 4ºC, the residual concentration of CN- was 0.2-0.3 mg/L and at -18ºC was 0.4-0.6 mg/L. Under conditions with the lack of oxygen, cyanides can be removed within the first 200 days. Then, this process fully stops. A stabilized cyanides concentration is 3.0-4.0 mg/L. The presence of sulfides increases the content of cyanides at the initial stage of testing. Then, the concentration of SCN at the temperatures above 0ºC decreases rapidly under oxygen-containing conditions. At the rise of temperature, a narrowing of peak at the curve and an increase of the destruction process are observed. At the end of testing, the concentration of thiocyanates in the moisture of wastes was 0.2-0.3 mg/L at the temperature of 20ºC and 0.5-0.6 mg/L at the temperature of 4ºC, respectively. The concentration of thiocyanates contained in a frozen sample and media which have the lack of oxygen stabilizes at a certain level owing to sulfides and does not practically change further. It was found that detoxification of oxidized cyanidation tailings with a simple composition which were disposed as filtration cakes can be possible. In this case, the concentration of cyanide in the moisture of disposed wastes can have a close value or equal to actual concentration during cyanidation. In order to meet the requirements of high ecological safety standards and successful detoxification process of toxic compounds in the tails under the action of natural factors, the conditions of air aeration with oxygen for the whole volume of tails are required. Keywords: cyanides, thiocyanates, storage, detoxification, flotation cakes

Sep 1, 2012

By V. E. Vigdergauz

The work presented shows results of electrochemical study of pyrite hydrophobicity evaluated by air bubble induction time (IT) measurements. On the basis of measured IT?s an average thickness of the thin liquid film prior to its rupture has been evaluated, which confirms long-range character of the interactions between air bubbles and hydrophobic surfaces. Obtained data are discussed in the frame of recent studies of structures of solid-liquid interface based on molecular dynamics simulations and results of surface force measurements.

Jan 1, 2014

By A. R. Videla, P. R. Brito-Parada, I. Mackay

"Linking results from laboratory scale experiments to industrial flotation behaviour is challenging. Typically, such experiments involve batch tests in which the system does not operate at steady-state, making it difficult to infer the effects that operating conditions have on flotation performance. In order to overcome this limitation a 4-litre recirculating tank was previously developed at Imperial College London. This tank is capable of reaching, and operating at, steady-state by recycling overflowing concentrate back into the feed. As well as instruments to control operating conditions, it is fitted with a system of sensors that allow the surface of the froth to be dynamically monitored. From this information, it is possible to measure the air recovery—a proxy for froth stability. Thus, this bench-scale tank can be used to understand the effect of differing operating conditions on flotation performance at steady state. However, so far, this cell has only been used to investigate idealised systems with only one or two species.Reprocessing of tailings dams is not only environmentally desirable but also increasingly economically feasible due to the declining head grades of primary deposits. There is also the added benefit of no further milling being required prior to flotation. However, the effects of fine and ultrafine particles on froth stability are not yet fully understood. In this work, the bench-scale continuous tank has been used for the first time to determine the flotation response of a complex feed, consisting of samples from a copper tailings dam, to changes in operating conditions. It was shown that the froth stability in the system is comparable to that of previous work and industrial tests, with a peak in air recovery being found at a superficial gas velocity of 1.13 cm/s. There is scope to optimize the froth stability of tailings flotation for enhanced metallurgical performance."

Jan 1, 2018

By S. Martins

The aim of this work is to compare three different results of charge motion in a modified 5ft diameter lab mill and to identify differences and similarities in these results. The lab mill is modified from tumbling a ball charge to tumbling a charge of disks. This modification replicates 2D motion. This 2D condition is measured using an instrumented disk (iDisk) and analysed using a video imaging system. The iDisk is equipped with a 3D accelerometer array and rotation rate sensors. With the help of a video system, some measured quantities are also determined externally. The results of these three predictions or measurements are presented. A discussion is included.

Jan 1, 2014

By T. C. Sun

Two wasted activated sludges (WAS), from an industrial wastewater treatment and a sewage treatment plant respectively, and 7 collectors are used to investigate the feasibility of air flotation thickening of WAS by adding the collectors used in mineral processing. The collectors experimented include straight chain fat acids with different chain length, sodium oleate, alkyl sodium sulphonate, sodium dedecylsulfonate, and dodecylamine. The results show that the thickening efficiency varied depending on different collectors. Of the collectors experimented, dodecanoic acid and dodecylamine are best collector for thickening both sludges.

Jan 1, 2014

By E. V. Bratygin, S. P. Elnikova

"In the article carrying out technique of experiments for estimation of power efficiency of process of crushing in cone crushers «in a layer». The conformity of the granulometric characteristics of the crushed products obtained as a result of the tests, the theoretical equations for the size characteristics, and the choice of the optimal equation for the prediction of the granulometric characteristics of the final products obtained by crushing ""in a layer"". Optimization of granulometric composition of power of crushers working ""in a layer"" is carried out with the purpose of reduction of the electric power consumption at reception of a product of required quality. As a result of the experiments, dependencies are obtained, the relevance and applicability of the crushing process ""in the layer"" for obtaining crushed stone of improved quality is proved. INTRODUCTION A number of equations have been proposed for calculating the breakage energy. These include equations by Kirpichev and Kick, Rittinger and Bond (Bogdanov, Olevsky, 1982). Another equation for calculating the specific breakage work in breakage by impact and in stratum was proposed by Devyatkin (Boiko, 2003). In these equations, the breakage energy is proportional to the particle size raised to some power. In the equation proposed by Devyatkin, the ore piece thickness or the feed average diameter is used. The relationship between energy and breakage can be expressed as an equation (Lynch, 1981; Tikhonov, no. 3, 2008) where k is a coefficient characterizing the energy parameter depending on the strength of the feed, l is size in microns. The Rittinger formula is obtained for n = 2, the Kirpichev-Kick formula for n = 1, the Bond formula for n = 1.5. For n = 3 or higher, the equation describes fine and ultrafine grinding. R. Hookey proposed a formula (Lynch, 1981, Tikhonov, no. 3, 2008), where the size exponent n is substituted by a size function In all of the above equations, a single value of the feed and product size is used; for example, in the Bond equation, size is defined as the particle size of the 20% oversize (P80 and F80). However, a single size value can represent multiple distributions, making that the Bond method inappropriate for determining the size (Lynch, 1981). Describing an equation for estimating the grinding energy will allow to design the electric drive and ore preparation circuit for the given breakage method."

Jan 1, 2018

By John Nell, Paul den Hoed

Carbochlorination tests were conducted with matched particle-size fractions of rutile, ilmenite and high-titania slag in a small bubbling fluidized-bed reactor. The effects of temperature, the type and proportion of solid reductant in the charge, and the fraction of Cl2 in the fluidizing gas were investigated. Tests confirm the need for solid carbon in the bed if chlorination is to run at high rates. With solid carbon in the bed, CO supplied with the fluidizing gas does not increase significantly the degree of chlorination after 75 minutes. Ilmenite is chlorinated more quickly than titania slag, which in turn is chlorinated more quickly than rutile. Rates of chlorination at 1100°C and 1000°C are much the same and significantly higher than at 900°C. Chlorination is associated with significant increases in particle porosity (even for rutile), which is brought about by the rapid initial chlorination of FeO and MnO (in ilmenite and slag) and (it is argued) by the chlorination of Ti2O3 which forms at high-energy surface sites. A reaction mechanism is presented; where possible, its validity is demonstrated by the support of empirical observations.

Jan 1, 2003

By A. Güney, G. Önal

"Karagedik Chromite Concentrator of the ETI Holding Co., which is located in Fethiye (south Turkey), has been producing chromite concentrate assaying 47-48 % Cr2O3 from the chromite ores containing 30-35 % Cr2O3 by using gravity separation methods since 1920. The tailings having 13-14 % Cr2O3, which had been removed from this plant, were accumulated at the stockpiles amounting about 1.2 million tons. In order to recover the ultra fine chromite particles from the Karagedik Concentrator tailings, the new process including Wet High Intensity Magnetic Separation and column flotation, was developed and the Karagedik Research Pilot Plant based on this process was commissioned in 2000. At this plant, the final concentrates assaying 46-48% Cr2O3 were produced and overall plant recoveries are about 60-65%.At the chromite concentrators using gravity separation methods, if their material size is about minus 1.0 mm, chromite particles especially pass to fine fractions according to their mineralogical structures and the ore-genesis (Önal and Güney, 1990). Generally, after crushing and grinding, the shaking tables and spirals are used at the chromite concentrators; therefore fine size chromite particles (-0.038 mm) are removed as tailings. Cr2O3 content of the -0.1 mm size fraction with 52.3% of the total amount is 19.58 % with Cr2O3 distribution of 82.6%.In order to upgrade the minus 0.1 mm size fraction of the tailings, assaying about 20% Cr2O3, Karagedik Research Pilot Plant (KRPP), which includes Wet High Intensity Magnetic Separator (WHIMS) and Column Flotation units, was installed by Istanbul Technical University (ITU), Mineral Processing Section in 2000.Feeding material of the KRPP having 5 tons per hour capacity is obtained from stockpiles amounting 1.2 million tons. After attrition scrubbing, the feed is sent to a screen with aperture of 1.0 mm. The screen overflow, assaying 5-6 % Cr2O3 is removed as tailings. Screen underflow is classified to –1.0+0.1 mm and minus 0.1 mm size fractions by using cyclone and sieve bend. –1.0+0.1 mm size fraction assaying 6-7 % Cr2O3, is sent to existing gravity separation plant. Minus 0.1 mm size fraction is firstly fed to WHIMS for pre-concentration and non-magnetic product assaying 10-11 % Cr2O3 consisting of serpentine, talc and olivine minerals are separated as tailings. Also magnetic product (25-30 % Cr2O3) obtained from WHIMS is fed to the two stages conditioners after dewatered to 30 % solid ratio."

Jan 1, 2003

By B. Mishra, Rahul Mohanty, Swati Mohanty, Swagatika Dash

Wet high intensity magnetic separators have been widely used in the mineral industry for separation of mineral particles based on magnetic properties. Usually, magnetic separators employ ordered array of grooved plates such as Lenoir and Jones plates onto which the magnetic particles get attached in the presence of a magnetic field. In the present work, we have carried out computational fluid dynamic (CFD) simulation, using Eulerian-Eulerian model to study the flow dynamics of magnetic and nonmagnetic particles within a matrix consisting of 2 mm size spheres of magnetic material, which are interconnected by wires, in the presence of a magnetic field. The three phases considered were the water, magnetic particles and non-magnetic particles. Model equations were developed considering each sphere in the matrix as a magnetic dipole, and the strength of the magnetic field at any point in the domain is due to all the dipoles. The size of the magnetic and nonmagnetic particles was 45 and 40 micron, respectively. The feed consisted of a slurry having 25 wt. % solids. The volume fraction of the magnetic particles was 0.04, and that of the non-magnetic particles was 0.045. The simulation was first carried out without the imposition of the magnetic field till a steady state was reached, and then the magnetic field was applied. The magnetic particles, as they flow down the matrix were attracted towards the region of maximum field gradient, which was in the central region of the matrix. A symmetrical pattern in the upper half as well as the lower half of the matrix was observed. As the particles moved downwards, the pattern changed, and near the outlet, most of the particles were found to flow out from the central part of the plane. This study can lead to a better design of a magnetic separator.

Jan 1, 2014

By Slobodan B. Vujic

"Some twenty years ago, during construction of flotation in the “Veliki Krivelj” copper and non-metallic mine Bor, a computer supported system for remote controle of technological process was installed. Nowadays, the major part of equipment of this system is worn-out and technically old-fashioned. Having this in mind a decision was made to design a new computer supported information-management system for Flotation. The paper presents a concept and features of project solutions.For the requirements of remote monitoring and management of technological process in Flotation of “Veliki Krivelj”, Copper and non-metallic minerals mine in Bor, Yugoslavia (hereinafter: CNM Bor), a measuring-regulation equipment was implemented and a computer control system, adjusted for that time, built some twenty years ago. The major part of this equipment is today worn out and technically out of date.Having estimated that production and business activities could hardly be more efficient, operative and successful on one hand, and available mineral and other resources rationally exploited, the CNM Bor made a decision in 1999 to improve information-management function of Flotation. The idea was that the set task be realized through development and introduction into practice up-to-date integrated and computer-supported production-business information-management system. The first logic step in completion of this task refers to engineering-creative determination of information management system (hereinafter: IMS), namely to project elaboration.When considering the real system from technical, technological, organization, monitoring-management, logistic and business aspects, the Project on IMS of Flotation, should provide a rational, modern and, for the real system conditions, complete solution. The Project solutions should be based on the most recent knowledge from computer and measuring-regulation technics as well as from CIM concept (Computer Integrated Manufacturing)."

Jan 1, 2003

By P. Gao, J. W. Yu

"Magnetizing roasting-magnetic separation is an important route for the beneficiation of refractory iron ores. In this investigation, a pilot-scale fluidized magnetizing roasting reactor was introduced and used to study the effects of roasting temperature and the flow rates of reducing gas CO and fluidizing gas N2, on the magnetizing roasting performance of an Anshan-type carbonate-bearing fine iron ore. The results showed that the hematite was almost reduced to magnetite by a gas mixture of 4 m3/h CO and 1 m3/h N2 at a roasting temperature of 540 °C. Under the optimized conditions, a high-grade magnetic concentrate assaying 66.1 wt.% Fe with a recovery rate of 91.2% was achieved from an Anshan-type carbonate-bearing fine iron ore assaying 42.0 wt.% Fe. The XRD, VSM, and optical microscopy analyses revealed that the siderite was successfully converted to magnetite by roasting. Some coarse hematite particles were difficult to reduce to magnetite completely; however, these generated magnetite particles with a fine hematite core could also be effectively recovered by magnetic separation after liberation from gangue minerals due to their strong magnetism. INTRODUCTION Magnetizing roasting followed by low-intensity magnetic separation has been considered as an effective solution, both technologically and economically, when upgrading refractory iron ores (Zhang et al., 2012; Peng et al., 2012; Li and Zhu, 2012). According to the type of roasting reactor, the magnetization roasting can be divided into shaft furnace roasting, rotary kiln roasting, and fluidized bed roasting (Zhu and Li, 2014).Shaft furnace magnetization roasting system is mainly composed of heating and reduction processes. The hematite ore is first heated to 700~800 °C in the heating zone, then falls into reduction zone where the weakly magnetic hematite is reduced to magnetite by coke oven gas at 550~600 °C (Yan et al., 2012). However, several years of engineering practices indicate that the shaft furnace can only process the hematite ores with a granularity of 15 ~75 mm, and the shaft furnace roasting is also characterized by heterogeneity of roasted product. Hence, the shaft furnace magnetization roasting technology is gradually replaced by high-gradient magnetic separation with the development of high-gradient magnetic separator. The rotary kiln generally handles the hematite ores with a grain size of less than 30 mm (Zhu and Li, 2014), however the formation of clinker ring in the rotary kiln will affect the yield of iron resource. In the fluidized bed furnace, the hematite ore is shaken up by an upward current of gas which maintains the individual particles in suspension (Yu et al., 2018). The precise adjustment of the gas velocity to the particle size and the specific weight of the hematite ore, make it possible to generate a floating mixture of gas and solids which behaves almost like a liquid (Yu et al., 2017a). The process is reported to have the following advantages over the other roasting techniques: ease of control due to absence of moving parts within the reactor, homogeneity of roasted products, ability to handle fine particles, and high efficiency of heat transfer and mass transfer (Li et al., 2015; Yu et al., 2017b). However, the simultaneous heating and reductive magnetization of hematite ore occur at the same place in the conventional fluidized bed reactor. Therefore, the reductive atmosphere, as well as the safety and stability of anti-explosion are hard to be controlled. Besides, the roasting temperature for conventional fluidized bed furnace is usually up to 950~1150 °C (Liu et al., 2017). Thus, the formation of clinker ring caused by high temperature will affect the operating efficiency."

Jan 1, 2018

By S. M. Bradshaw, C. Dorfling, F. Ngandu

"Selenium removal and platinum group metal (PGM) recovery from copper sulfate leach solutions form an integral part of platinum producers’ base metal refinery operations. Recent studies found that substantially higher PGM recoveries can be achieved if excess thiourea instead of sulfurous acid is used as precipitation reagent; however, the impact of the proposed process on downstream processes was unknown. The objective of the current study was therefore to investigate the effects that excess thiourea and residual selenium present in the rich copper sulfate electrolyte have on copper electrowinning. This was achieved by performing cyclic voltammetry tests using a platinum rotating disk as working electrode, a graphite auxiliary electrode and a saturated calomel reference electrode. A synthetic copper sulfate electrolyte containing 0.01 M Cu2+, 1 M H2SO4 and varying amounts of selenium (20 – 150 mg/L) and thiourea (10 mg/L and 100 – 300 % excess) was used. The results obtained have shown that both thiourea and selenium interact with the cupric ion cathodic reduction reaction. Thiourea polarized the working electrode and lowered the efficiency of the cupric reduction reaction. Tests on the solutions with high selenium concentration showed simultaneous reduction of copper and selenium, which led to copper selenide formation. Nodule formation on the deposit surface also became significant at higher selenium concentrations. Based on these results, it was concluded that precipitation of PGMs from the copper sulfate solution with excess thiourea is not feasible due to the detrimental effect on downstream electrowinning operations.INTRODUCTION During the high pressure oxidative leaching stage in a typical base metal refinery (BMR) circuit, selenium, tellurium and some platinum group metals (PGMs) are dissolved along with the desired copper ions. The impurities (selenium and tellurium) may pass to the copper electrowinning circuit where it can result in the formation of nodular copper electrodeposits or reduced current efficiency. The presence of PGMs in solution, on the other hand, increases the precious metal inventory and potential losses of the operation. Currently, sulfurous acid is widely used for selenium and tellurium precipitation from copper sulfate leach solutions. Sulfurous acid is capable of reducing cupric ions to cuprous ions; the generated cuprous ions then react with Se4+ and Se6+ to precipitate selenium as a copper selenide (Bello, Dorfling, 2014). Recent studies have, however, proposed the use of excess thiourea as a precipitating agent for the removal of selenium and tellurium; it has the advantage of improved PGM recovery in the Se/Te precipitation step (Lottering, Eksteen et al., 2012; Mulwanda, Dorfling, 2015)."

Jan 1, 2018

By Megha Patel

"The objective of this project was to investigate the application of Prompt Gamma Neutron Activation Analysis (PGNAA) technology to provide real-time on-belt elemental analysis of feed ore in base metal sulphide processing, in this case at the Mount Isa Mines Zinc-Lead Concentrator Heavy Medium Plant (HMP). After initial exploratory testwork proved successful, a Geoscan On-Belt Elemental Analyser was retrofitted onto the existing HMP feed conveyor. Dynamic calibration of the Geoscan was conducted based on laboratory XRF analysis results of the HMP feed conveyor hammer autosampler samples from May to November 2013. Comparison of the Geoscan results to the laboratory XRF analysis results during and after dynamic calibration indicated the technology had acceptable accuracy to be incorporated into HMP process control. The variation between the two sets of data includes all primary sampling, sample preparation and XRF analysis errors as well as the Geoscan errors themselves. The Geoscan instrument precision must be calculated separately through a duplicate sampling campaign and independent laboratory analysis before extending the scope of its range of application beyond HMP process control. The expected benefits of integrating the Geoscan real-time data into HMP process control are optimised HMP metal recovery, improved cost efficiency and improved stability of the downstream processes (milling and flotation). Utilisation of the Geoscan will also enable improved feedback to mines on grade control and dilution, and provide additional information on individual ore types when fed as campaigns to HMP."

Jan 1, 2014

By Wenying Liu, Marek Pawlik

Long-chain ionic surfactants, with fatty acids and amines as the most important representatives, are widely used as collectors in froth flotation. These surfactants, generally referred to as weak electrolyte collectors, frequently form solid insoluble precipitates within a certain pH range. However, the action and behavior of these colloidal precipitates in froth flotation systems are not well understood and has not been well decoupled from those of dissolved forms. The objective of this study was to understand and compare the role of colloidal precipitates with that of the dissolved forms at gas-liquid and gas-liquid-solid interfaces. Using primary amine as the model surfactant, experiments were carried out to measure: the maximum volume of bubbles generated in the presence of dissolved and precipitated forms of the surfactant; surface tension for both forms of the surfactant using the drop shape and maximum bubble pressure methods; and contact angle using the sessile drop method. The experimental results showed that: in the presence of the precipitate, bubble volume was smaller, which was correlated with the lower surface tension and higher contact angle measured; the surface tension of solutions containing surfactant precipitate was affected by the surface age of liquid droplets. This study enhances understanding of the interfacial behavior of long-chain ionic surfactants under different conditions, which would help improve the efficiency of reagent utilization in froth flotation.

Jan 1, 2014

By A. A. Novoselov, U. Kelm

"Large volumes of mine tailings accumulated in surroundings of porphyry copper deposits represent a growing threat to environment. They contain significant concentrations of toxic metal and metalloids which can contaminate river runoff, ground waters or can be transported by wind. Both extreme pH of fluids in tailings impoundments and high surface areas of processed mineral grains provide their increased reactivity. As a result, during only a few decades, As, Cu, and Mo can be mobilized, redistributed through the tailing column and accumulated through post-deposition leaching, evaporation and contamination with natural fluids. Those processes are reflected in the forming of secondary minerals. Gypsum, Fe oxides/hydroxides, efflorescent salts and clay minerals are typical alteration products in tailings. Here we present the results of reactive transport simulations implemented on the base of PHREEQC and SUTRA codes. The one-dimension model emulates the mass balance between rainfall, evaporation and subsurface runoff, the kinetically- and thermodynamically-driven dissolution of tailing minerals, advective and diffusive transport of tailing fluids, and precipitation of secondary phases. A typical tailing column is composed of four unequal layers with predominance of (i) evaporation, (ii) secondary mineralization above, (iii) below water table, and (iv) near the bottom of dump. Those horizons are characterized by contrasting pH, chemical composition and bulk mineralization of pore fluids, distinct accessibility of atmospheric oxygen and, as a consequence, distinct intensity of sulfide oxidation. The modeling and its verification on Chilean tailings impoundments reveal the complexity and high rates of secondary mineralization. The accumulation of toxic alteration products is controlled by fluid transport through the tailing column induced by both rainfall/evaporation and exchange with subsurface runoff. The geochemical modeling is a powerful approach which allows comparing the processes in tailing deposits produced by distinct flotation regimes and providing the long-term predictions of their environmental impact as well as identifying sectors of tailings for possible re-processing."

Jan 1, 2018

By Victor V. Karmazin

"The appearance of the precise equipment for analysis of results of the laboratory tests with using of the computer processing allows raising accuracy of the estimation of the expected indexes of the mineral processing. Certainly, laboratory tests will not be able to substitute completely industrial ones, but allow reducing the amounts of the industrial tests, that vastly reduces the cost of technological forecast and preparation of data for projection.Calculation of the potential indexes of mineral technology (mass yields and the metal content in products) is fulfilled on the base of results of measurements of the mineralogical liberation parameters using special formulas.The quality of the concentrate ßc = a + ?l • ?s • ?i (ßt - a) can be achieved on a level of the theoretical metal content of a mineral - ßt only if coefficients of mineral processing, of liberation ?l and selectivity ?s of grinding, effectiveness of separation, will reach 1 (a - metal content of the row ore).Increase ?l by overgrinding automatically decrease ?s, and only by destroying of particles of ore along surfaces of accreting of minerals (?i = 1) and when values of all three coefficients will aim to 1, then ßc ? ßt.The degree of liberation of the useful mineral is the ratio of mass of free grains of the useful mineral in the product to general mass of the same mineral in this product. The factor of the liberation, which is defined by curves of dressability by angle of slop of the curve of the elementary faction - ?, is Kr=1 – tga. Kr changes from 0 to 1 when a changes from 45o to 0o. The liberation is reached by grinding of the material, although degree of the liberation, as a rule, is lower than the degree of the grinding."

Jan 1, 2003

By D. Izerdem, S. L. Ergun

"Beneficiation of the finely disseminated valuable minerals has been an important issue in the mineral processing field for decades. Treatment of the fine materials becomes difficult with using traditional gravity concentration equipment. To investigate particles behavior in a commonly used conventional gravity concentration equipment, a comprehensive study was undertaken in a plant, which only consists spiral concentrators as concentration units. Spiral concentrators require relatively coarse material to effectively concentrate valuables as well as offering greater simplicity for especially higher grade feeds. In the current work, chromite ore (d80 = 290 µm) was treated using spiral concentrators and the performance of spiral concentrators was examined. The design of the separation circuit comprised of rougher, cleaner and scavenger stages. The resultant fractions produced by each separation unit and feed samples were analyzed to identify the particle sizes, mineral liberations and chromite content. Grade and recovery comparisons were presented in size-by-size manner and the separation tendency of the particles were determined in varying feed rate conditions. The overall results indicated valuable mineral loss of the plant and alternative suggestions were pointed to reach the target values.INTRODUCTION Spiral concentrators are simple low energy consuming devices, which are generally used for pre-concentration of the minerals. They are cost efficient equipment separating minerals mainly based on density differences of the minerals. The adjustable splitters remove the concentrate as the remaining stream continues to move down the spiral. Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational force, centrifugal force, hydrodynamic drag and Bagnold force (Atasoy and Spottiswood, 1995; Burt, 1984). Since the classification in a spiral concentrator depends on particle specific gravity and size, the operation of spirals can be analyzed using size recovery or partition curves (Bazin et al., 2014). Spiral concentrators possess multiple design parameters for a variety of applications. The design parameters that govern the performance of the spiral can be identified as the diameter, number of turns, slope, pitch and the profile of the trough. For an efficient separation on a spiral concentrator, the properties of the slurry flowing on a spiral, ore texture, percent solids and flow rate play important roles."

Jan 1, 2018

By S. P. Das

Tumbling mill is an important unit operation in a mineral processing industry whose operation needs to be understood to make it an energy efficient unit. One of the important mill parameters is the impact spectra generated by collision of the moving charge mass on the mill shell. This process also generates mechanical vibration on the mill shell and propagates to the plumber block of the mill. In this work, we tried to understand the impact spectra by using different minerals such as Banded Hematite Quartzite (BHQ), Hematite and Quartz as mill feed of a semi-autogenous (SAG) mill. The said mill is of 1000 mm diameter and fitted with a force sensor on the mill shell and a vibration sensor on the plumber block. The analysis of the impact spectra was done by taking into consideration the peak impact force above a certain threshold value. It clearly shows that the impact force decreases as the particle size become finer irrespective of the mill feed material. This can be used as an effective tool by the mill operators to have an understanding of the mill product size reduction. The mechanical vibration tapped by a tri-axial accelerometer was analyzed by power spectral density analysis. The vibration signal analysis shows the variation in the power spectrum magnitude both at lower and higher frequency. It also shows inconsistency in case of BHQ where it shows a significant decrease in vibration at lower frequency and increase in vibration at higher frequency. Therefore, the impact spectra analysis is a better method compared to vibration analysis in understanding the mill product size reduction.

Sep 1, 2012

By I. Yu. Rasskazov, A. V. Rasskazova, N. M. Litvinova, N. A. Lavrik, V. G. Kryukov

The possibility of the intensification of the gravity processing of complex iron-manganese ore, which contains the finely dispersed inclusions of gold and platinum is shown. Clear mineral fractions of precious metals were sorted out of the different types of ores (quartz-braunite and carbonate- magnetite ore, ferruginous quartzite, carbon-containing shale, breccia-limestone and dolomite breccia). Composition and structures of precious-metals particles was detailed. The industrial content of platinum and gold was found. Precious-metals mineralization is character for all types of ores. High content of platinum is indicated in the carbonate-magnetite (up to 11.3 mg/kg) and quartz –braunite (up to 10 mg/kg) types of ore. Gold is presented in the ferruginous quartzite (up to 1.29 mg/kg) according to the data of the reduced mineralogical analysis. The composition of native platinum depends on the type of the ores: 1) quartz-braunite type contains isoferroplatinum (Pt3Fe) with Cu, Rh, Ir, Ru; 2) carbonate-magnetite type contains isoferroplatinum with Cu, Sn, Ni, Rh, Ir, Os; 3) pyritic-carbon ore contains isoferroplatinum with Sn, Ni; 4) ferruginous quartzite contains isoferroplatinum without admixtures. The ultrasonic treatment of mineral aggregates (P = 41.5 Watt, I = 15 W/cm2) made possible the liberation of fine particles of precious metals. Smooth-shaped or crystalline mineral aggregates are effectively liberated after acoustic treatment. Their surface is freed from impurities. The aggregates with the complex form and structure, which consist of the numerous plates and the grains, are not effectively liberated from impurities. It is shown that the ultrasonic treatment of aggregates with the fine inclusions of precious metals contributes to the liberation of the particles of platinum and gold and intensification of the gravity processing of refractory ore. This approach contributes the increase of the raw-material base of precious metals.

Jan 1, 2018

By Venkata S. Buddhiraju

Pelletization of iron ores involves balling on a rotating disc to produce wet pellets and induration of wet pellets on a moving grate to produce fired pellets. The quality of pellets produced and the productivity of the pelletization process depend strongly on the characteristics of the feed to the pelletization disc, especially the particle size distribution and the moisture content. The upstream processes involved in the preparation of pelletization feed include grinding, thickening and filtration of the iron ore slurry. The focus of the present work is the closed circuit wet grinding of iron ores. The circuit consists of a primary ball mill, a regrind mill and a hydrocyclone. A population balance model was developed to predict the grinding kinetics and an empirical model was fitted for the separation of fine particles from the coarse particles in the hydrocyclone. Batch grinding kinetics experiments were performed on a laboratory scale ball mill to obtain the ore breakage parameters which were subsequently used for the simulation of the industrial mills. The models were customized for the industrial operations and the effects of different process variables like feed flow rate, water flow rate, etc., on the size distribution of product from the grinding circuit were studied. Additionally, different circuit configurations were simulated to determine operating conditions that could result in the desirable product particle size distribution. The results of simulation were in close agreement with plant observations and the new circuits explored through simulation have helped in identifying potential opportunities for process optimization and control

Sep 1, 2012