Search Documents

By C. Vipulanandan, M. Dawood, Dongmei Pan

"With the aging infrastructure, there is a need to maintain and extend the service life of steel structures in general and steel piles in particular. Steel piles support not only vertical loads but also dynamic horizontal loads in onshore and offshore applications. In order to select the appropriate methods to repair corroded steel piles used in onshore and offshore application, corrosion mechanisms were investigated with the rate of corrosion in various environments. The corrosion rate of steel in soil, water and soil-water interface varied from 2 to 500 µm/year. Based on literature review and analyses, the repair methods can be broadly characterized as protective coating, electro-chemical methods, wrapping and encasement and partial replacement of steel. Also, methods to evaluate the repair materials and the repair configuration have been documented.IntroductionOne of the biggest challenges facing the aging infrastructure is the materials loss and deterioration due to corrosion. Many studies indicate that in the US alone, costs due to corrosion loss is more than $276 billion annually (Michiel et al., 2010). Corrosion is the major cause of deterioration of steel structures and components (MNC, 2005). Load bearing steel piles are used as foundations for various types of structures and hence corrosion is very much influenced by the environment such as soil, water and soil-water interface. Corrosion of steel pile foundations may result in reduced capacity in the axial and lateral directions. Hence, understanding the rate of pile corrosion is essential to select the appropriate repair methods to avoid excessive deflection and failure (Decker et al. 2008).To prevent the deterioration mechanisms that attack a pile, it is fundamental both to identify and understand the deterioration mechanism that has been the cause of damage. Understanding the deterioration mechanism allows the engineer to design a repair that will combat this type of damage. It is widely recognized that the corrosion of carbon steel in soil, water and soil-water interface proceeds according to the following simplified anodic reaction and cathodic reactions in the presence of oxygen (Decker et al. 2008)."

Jan 1, 2017

By Haijian Shi, Drew Pizzo

This article focuses on the appropriate application of subsurface investigation methods for transmission structures, which are typically designed to resist lateral rather than vertical loads. Currently, the three methods used most often for the subsurface investigation of transmission structures in the field are the Standard Penetration Test (SPT), the Cone Penetration Test (CPT), and the Flat Dilatometer Test (DMT). Each of these methods has advantages and disadvantages, and each is more applicable to some scenarios than to others. To gain a better understanding of these test methods and the implications of using them for various kinds of applications, a comparison study was conducted in the field in Maryland, for three boring locations. Each boring location was explored using each of the three tests as stated. The results of the tests and lessons learned are presented and compared, and these comparisons show that the three test methods agree on the majority of the findings. The results from each test method were also used to derive key parameters such as the soil friction angle for given foundation designs considered in order to establish a clear basis for comparison. Recommendations for performing transmission structure subsurface investigations are made in order to optimize the use of each method and thereby optimizing subsequent foundation designs. INTRODUCTION For overhead transmission structures, the most important structural requirement for determining the foundation design differs from the requirement for other structures such as buildings and bridges in accord with the conditions the transmission structures will need to withstand. In addition to the ability to bear a given vertical load consistent with its use, the foundation must bear lateral loads arising from wind and other weather conditions. The foundation types used most often for overhead transmission monopole structures include concrete drilled pier, vibratory caisson, and direct embedment. In order to determine an appropriate and even an optimum foundation design for any given set of conditions, an appropriate subsurface investigation method or approach is needed. Currently, the standard penetration test (SPT), the cone penetration test (CPT), and the flat dilatometer test (DMT) are the three most commonly used subsurface investigation methods.

Jan 1, 2018

By D. R. Dance

The Resonant, or as it has more commonly come to be known the 'Sonic' Pile Driver, dates back to the early 1960's, when prototypes were produced by Charlie Guild, of Providence, Rhode Island, and A1 Bodine of Los Angeles, California, these were later to be developed into the unit known as the BRD 1000. Based on this initial work, the Shell Oil Companies of Sonico and The Resonant Pile Corporation, produced and operated 30 of these BRD 1000 machines, which were used throughout the U.S.A. and Canada on a wide range of foundation projects. Subsequent to this, Raymond International and G K N, of England, operated units on programs; the G K N units being of slightly modified configuration. In 1973 Hawker Siddeley Canada Ltd., acquired the license for the Pile Driver and related systems with the intent of promoting the use of the machines to install support pilings on the Alyaska Pipeline Project, but this did not materialize due to problems with the oscillator. After radical redesign and field testing of the oscillator system the unit was employed on a number of test projects principally in Northern Canada and Alaska.

Jan 1, 1987

By Andrew L. Peterson

CATOH Inc. of Weedsport, New York recently completed a very challenging Bored-In Pile project which features unique construction techniques in the installation and load testing of 45 and 100 ton capacity piles. The bored-in piles were installed on a twenty-nine million dollar New York State Department of Transportation project which began in the fall of 1995 and ended in March of 1997. The project included the construction of 5 new bridges to alleviate a very congested traffic network which had come to be known as the "Octopus" in the small city of Ithaca, New York. CATOH Inc. was awarded the piling contract by general contractor Santaro Industries in the fall of 1995. Piling installation work was completed in March of 1997. BACKGROUND The project is located at the southern tip of Cayuga Lake which lies in the heart of Upstate New York's Finger Lakes Region. This region is popular not only for wine making and vacationing, but also for its impressive geological history. The glacial activities that helped to form the deep valleys of this scenic area are also responsible for creating challenging underground conditions for deep foundations work. CATOH developed two pile designs to accommodate differing site conditions on the project. Internally reinforced piles were developed for use in the center of the valley and externally reinforced piles were developed for locations close to the valley wall.

Jan 1, 1997

Jan 1, 1987

By J. M. Mitchell

Kuala Lumpur, Malaysia is underlain by karstic limestone. Firm clays, mudstones and siltstoncs of the Kenny Hill Formation overlie the limestone for about two thirds of the city. The remaining third has deep deposits of very soft alluvium, or tin mining slimes, overlying the limestone. It is only recently that large buildings have been constructed in the area. Arup Jururunding have been concerned with several projects located on the limestone, although space here only permits the description of four sites in detail. The experience has allowed the development of a design approach for the foundations. The aim is to make the architectural scheme compatible with the geology. This is not always possible, and examples are given of both situations. The case histories give examples of compensated foundations, and piled foundations include steel H-piles, precast concrete piles, micropiles, bored piles with rock sockets, and barrettes up to 90m deep.

Jan 1, 2010

By Ray. K. Filip

The concept of installing a steel sheet pile retaining wall into the ground by "pressing" has resulted in the development of various equipment solutions over the last thirty years e.g. Taylor Woodrow ?Pile Master', Giken 'Silent Piler" & Tosa 'Still Worker?. Dawson Construction Plant Ltd (DCP), have recently advanced the pile pressing concept with the introduction of their 'Push-Pull' system. This advancement offers significant improvements in the quality of installation compared with traditional pressing solutions but also greater versatility, higher productivity and, most importantly, generates new opportunities through a wider range of applications for "silent piling'. This paper will focus primarily on the use of the Push-Pull concept in the construction of a unique "integral" bridge in Milton Keynes, England. Finally, the paper touches on the development of quiet, vibration-less pile extraction equipment, which allows steel to be considered the foundation material of choice for truly sustainable construction. It is no longer acceptable to leave unwanted piles in the ground.

Jan 1, 2006

By E. Stoetzer

In all known deep mixing processes the existing soil is mixed with self hardening slurry by mixing tools that rotate about a vertical axis (augers, mixing paddles). Wall panels are constructed using sets of multiple mixing tools combined into a single unit. These techniques have been developed on the principle of the rotary drilling technology. In contrast, the new Cutter Soil Mixing or CSM technique is derived from the cutter technology. The soil is loosened and broken down by cutter wheels, then mixed in-situ by the rotating cutter wheels with the self-hardening slurry - introduced into the ground between the two wheels - to form a soil-slurry mortar. The main area of application lies in the construction of cut-off and retaining walls.

Jan 1, 2006

By Yin Zongze

The pile foundation of Sutong bridge pylons is an extra large pile foundation. The length of piles is 115m, and the diameter of the piles is 2.5-2.8m. Since the traditional design method may not determine the settlement and capacity reasonably for such a large pile foundation, the finite element method is used to study stress and deformation of the foundation. The interface element is set to simulate the possible slide between piles and soil layers. The hyperbolic model is taken for soils. Parameters are determined from triaxial test first, and then modified by back analysis on basis of in-situ loading test. The computation results show that the axial force of piles changes with the location of the pile. Outer piles support greater axial force and also friction. The settlement will not be greater than 26cm. The stress and deformation of the pile cap, the abutment, are obtained too. The whole foundation is safe.

Jan 1, 2006

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shaft (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, ? Design and construction of the scour protection for the two main pylons, ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2005

By Kazimierz Gwizdala

In the paper the method for estimation of settlement of vertically loaded piles in a group is presented. The method is generally based on the hybrid procedure with non-linear solution for single piles and with interaction between them for the low-strain shear modulus. Some attention is paid to the influence of deformation and strength parameters used in calculations. The applied model is verified in the framework of the research programme carried out recently in the Geotechnical Department of Gdansk Technical University. It concerns monitoring and analysing the settlements of the existing structures on piles. A comparison of calculation and measurements results for two tested buildings is presented as an example.

Jan 1, 2002

By B. Ladanyi

The design philosophies for piles in unfrozen and frozen soils are compared, and their similarities and differences are underlined. It is shown that in frozen soils, the long term behavior of a pile is difficult to predict, because of inadequate knowledge on the behavior of adfreeze bond with time, and on the value and variation of the lateral normal stress acting on the pile. Both of these problems are discussed in the paper on the basis of laboratory tests and theoretical analyses.

Jan 1, 2010

By Derek J. Lennon

Ground conditions in central Glasgow generally comprise loose granular deposits overlying stiffer soils. CFA piling would normally be preferred for urban sites in these ground conditions, but flighting of the superficial deposits has on occasions resulted in building damage. Over the last five years rotary bored piling with vinyl polymer support fluid has proved to be an economic alternative to bentonite slurry. Two case histories in central Glasgow are described in this paper, one for piles founding in granular soils and one for piles founding into bedrock. A comparison is made between the methods required for disposal of the liquid waste from bentonite and vinyl polymer slurries.

Jan 1, 2006

By Giuliana A. Zelada

This paper reports on a study of 43 compression load tests (five fully instrumented) and ten pullout tests of auger cast-in-place (ACIP) piles in sand. Eight design methods reported in the literature were used to predict the measured pile capacities. Ultimate load capacities of the ACIP load tests were determined using two different definitions of ultimate capacity and compared with predictions. Load transfer behavior was determined from a study of the fully instrumented pile tests and compared to predicted values. Recommendations are made regarding the design approach most appropriate for these foundations and the best procedure for estimating ultimate capacity from pile load tests.

Jan 1, 2000

By P. H. Derbyshire

The use of continuous flight auger piles has increased significantly in the U.K. to such an extent that it is now the most widely used method of constructing small diameter bored piles. This paper describes the improvements in equipment, techniques and particularly monitoring that have led to this growth. A review of the equipment in use describes how purpose built self erecting machines have been generally adopted. Improvements in ancilliary equipment are described. Concrete has almost completely replaced grout and techniques have been developed to extend the length of reinforcement that can be placed. Leading specialist contractors have developed instrumentation to monitor the construction of the pile (in terms of time, depth, torque, concrete pressure and flow) and keep a record for checking. A further significant development of this monitoring by means of sensors at various levels in the auger stem is described. The results obtained from this monitoring are reviewed and future developments discussed.

Jan 1, 1989

By Tom A. Armour

Different variations of soil nailing techniques have been used in the United States since the late 1970's. Such techniques owe their origins to French developments, which began in the early 1970's as a spin-off from European tunneling excavation support practice. The growing demands of urban infrastructure development and rehabilitation and environmental protection have created an active and expanding soil nailing market demand for earth retention and slope stabilization in the United States since its early developmental years. There is a clear need for a fundamental review of the large number of soil nailing techniques that are currently being used in the United States. Following a brief summary tracing the historical development of soil nailing and a generic classification of applications, this paper provides a review of the different recent advances in the design and construction of soil nailed systems. Discussion topics include nail design advances, permanent "top-down", structure support/underpinning, alternative face stability measures, composite systems, hollow bar and fiberglass nails and architectural reinforced concrete/shotcrete facings. Case histories will be presented to illustrate each of these advances.

Jan 1, 2003

By Saeed Salehi Malekshah

In hybrid foundation system or piled raft foundation (PRF), the raft has adequate bearing capacity and piles are usually required to ensure overall stability of foundation and also to act as settlement reducer for high rise structures. When piles are connected to the raft, a high axial stress may develop and one alternative is to disconnect the piles from raft and consider them as stiffeners for supporting soil. This system is known as disconnected piled raft foundation (DCPRF). Cushion, a compacted coarse grained soil layer, can be used beneath the raft to redistribute and adjust the stress ratio of piles to subsoil and plays an important role in mobilizing the bearing capacity of subsoil and modifying the load transfer mechanism of piles. In this study, finite element method (FEM) has been employed to investigate the effect of different parameters such as cushion stiffness, gap height, raft thickness and piling configuration on the behavior of disconnected piled raft foundation. The analysis is performed on different foundations of hypothetical and real case histories. Results indicate that increasing the raft thickness reduces the differential settlement and pile head axial stress. Concentrating the longer disconnected piles similar to connected ones beneath the central area of raft, decreases settlement of raft. With increasing cushion stiffness, vertical stress ratio of piles to subsoil increases, but settlement decreases. Increasing gap height from 0.1 m to 1 m decreases the vertical stress ratio of piles to subsoil.

Jan 1, 2011

By Rick Deschamps

The Block 76 project includes the demolition and redevelopment of an entire city block for mixed use retail, office and residential properties directly adjacent to Historic Temple Square in Salt Lake City, Utah. Excavation was carried out 65 ft below street grade and by as much as 50 ft directly below adjacent buildings supported by shallow foundations. Movements of the earth retention system and adjacent buildings were monitored in real time using automated equipment which complemented traditional geotechnical instrumentation. In the areas immediately adjacent to the existing buildings 9 stories or greater, anchored diaphragm walls were employed. Areas of the site not supported by diaphragm walls employed a soil nail wall system. Jet grouting was used for water cutoff in lieu of dewatering along the north and east sides of project. In total, the earth retention scope included 45,000 sq. ft of diaphragm wall, 104,000 sq. ft of soil nail wall, and micropile underpinning of 3 buildings. This paper provides an overall description of the Block 76 project. A detailed account is provided of the technical and commercial lessons learned. The project provided a unique example of how an owner can receive best overall value by acceptance of some technical risk up front. Benefit was gained by allowing the contractor to reduce contingencies within the bid from unknowns on a fast-track project.

Jan 1, 2009

By G. X. Zeng

A calculation programme of finite element method has been developed in order to study the behavior of excavation with sheet piling in soft clay. Based on a series of isotropically consolidated-undrained tests (CIU) on Hangzhou clay a linear relationship between the normalized initial tangent modulus number, E1, and stress-path parameter, a, is found for four different stress paths, and stress-path dependent modulus equations derived. Meanwhile, several influence factors, such as embedment depth and stiffness of the wall and soil conditions, were taken into consideration in the programme. Some valuable conclusions were obtained. Finally, a case history was studied by the proposed method of calculation. The result of calculation and the field observation are in good agreement.

Jan 1, 2010

By Alan D. Fisher

Amtrak made a decision to replace an aging bascule bridge with a vertical lift bridge for their crossing of the Thames River in New London, Connecticut. The new lift bridge occupies the same alignment and shares the same foundations as the bascule span. During construction the deep foundation caisson supporting the bascule span settled and tilted. Investigation into possible reasons revealed interesting historical facts, both of the construction of the innovative open well caisson foundations and of the state-of-the-art in tremie concrete placing methods in use at the turn of the century. This paper describes both of these topics.

Jan 1, 2008