Search Documents

By B. R. McEwen, A. N. Samis, J. H. Gray

"The Quebrada Blanca Copper Mine is an open pit copper project located at 4200 m elevation in the Chilean Andes. The deposit is a world-class supergene enriched porphyry with a mining reserve of 89 Mt of 1.3% copper. The supergene zone will produce 6.3 Mt of ore per year for more than 15 years to produce 75 000 t of cathode copper per year.This paper will review the project geology the computer model ling of the deposit, the mine planning process and the property production scheduling. With copper production .fixed by the onsite electrowinning capacity, the planning and scheduling aspects to optimize the project NPV will be discussed. Some of the logistics, equipment. personnel and process difficulties of operating a mine at 42()() m elevation will also be described. IntroductionProject DescriptionThe Quebrada Blanca Copper Mine is an open pit copper project located in the northern part of the Chilean Andes. The project is based on the supergene enriched portion of a porphyry deposit which has a mining reserve of 89 million tonnes at 1.3070 copper. Below the enrichment blanket, the protore represents a further resource.All ore will be leached, the higher grade material will be crushed and stacked for thin layer heap leaching, and the lower grade and oxide material will be dump leached as run-of-mine material. Solvent extraction and electrowinning will be used to produce 75 000 tonnes of cathode copper per year. Power will be supplied by a 40 MW on-site diesel generating plant with the waste heat being used for process heating. The leaching operation will operate in excess of 15 years and may be followed by open pit mining and conventional ore concentration of the underlying primary sulphide mineralization.Because of the dry location water will be piped 37 km from a ground water source at the Salar de Michincha. Water requirements will be approximately 1.5 million m3/year. The operation will eventually employ approximately 550 people on a 7-day-on, 7-day-off rotation with two twelve-hour shifts per day with an on-site camp. Busing will be provided to the port city of Iquique."

Jan 1, 1994

By László Guczi1

Nanosize model gold particles with varying size were fabricated by deposition of a 10 nm thick gold film onto SiO2/Si(100) substrate by electron beam evaporation followed by modification using low energy Ar+ ion bombardment. The change in particle size were monitored by the Au 5d valence band states determined by ultraviolet photoelectron spectroscopy (UPS). The gold/iron oxide interface was studied by iron oxide deposition on gold. It was found that the energy profile of Au 5d valence band states are strongly redistributed with decreasing the gold particle size mostly affecting at the lowest and at the highest binding energies. The size effect in the UPS spectra can be interpreted by the energy redistribution rather, than by narrowing the 5d states. The iron oxide deposition increases the catalytic activity in CO oxidation whether it is on gold nanoparticles or on a continuous 80 nm thick gold film. The activity enhancement is significantly larger in case of gold nanoparticles. The interface interaction is operative in enlargement of the catalytic activity even if gold particles are not exposed to the surface, but they are located below the iron oxide layer.

Oct 1, 2003

By G. Danha, S. Wabula, D. Glasser, D. Hildebrandt, N. Hlabangana

"Impact tests on single particles or a bed of particles are used to determine the fracture characteristics of particles. Many different techniques have been adopted in comminution in order to find ways of optimizing energy consumption in the size reduction process. In this paper, we apply one such method called the Attainable Region (AR) analysis technique to optimize the impact energy on a bed of silica particles. The attainable region is a fundamental approach that is equipment-independent and can be used to analyze breakage processes. The AR is defined as a set of all possible outcomes, for the system under consideration that can be achieved using fundamental processes operating within the system.INTRODUCTIONThe energy crisis in Southern African has reached such critical levels, that most cities in countries like Zambia, Zimbabwe, Lesotho, Swaziland and even South Africa are experiencing load shedding challenges lasting sometimes up to 18 hrs a day. Southern Africa is well known for its riches in mineral resources, and the economies of most states in this region are driven by the mining & mineral processing sector. With the emergence of small scale miners due to government empowerment policies, national energy providers have had to resort to power cuts mainly to domestic users in a bid to cope up with the huge industrial electricity demands.It has been estimated that about 4% of the total energy used in the world is consumed by the mineral processing sector (Fuerstenau & Lutch, 1999). Tomanec and Milovanovic (1994) estimated that milling alone accounts for more than 50% of the total power used in mineral processing, but this can rise to as high as 70% for hard or finely dispersed and inter-grown ores. Today, the greatest challenge in mineral processing is how to optimize energy input to the size reduction process (Dey & Das, 2013; Nomura & Tanaka, 2011), where it has been observed that only a small percentage (1.5%) of the total energy input really does the breaking (Khumalo et al., 2008) while the rest is consumed by the equipment concerned and lost to contacts that do not result in breakage. The immediate benefits of focusing research on the optimization of energy in size reduction operations in the mineral processing sector lies in potential savings on industrial electricity usage that may then be directed towards domestic users."

Jan 1, 2016

By Brian Lewis

"IntroductionThe ion exchange process is classed as a purification and concentration stage. In the uranium industry it is used to separate, and recover uranium, from a solution produced in the leach and subsequent solid washing circuit, that contains uranium as well as some impurities. The final product from this circuit is a solution, containing uranium at a 15 to 25 fold increase in concentration, with a chemical composition suitable for the ""Precipitation"" circuit.The process is a reversible chemical ""ION"" exchange, between a solution, and solid phase, with the ""resin"" being the solid phase. Various chemical changes in the solution phase will permit the resin to remove uranium from a solution or have the uranium removed from the resin back into a solution phase. The former loads uranium onto the resin, and is called the ""adsorption cycle"", and the removal or stripping is known as the ""elution cycle"".Ion Exchange resin is a semi-rigid polystyrene spherical bead, approximately 10 to 30 mesh. It is used by placing the resin in a vessel, so that a porous bed of resin is formed, through which the solution may flow.There are many different types of vessels, and systems used to hold the resin, but it is not the intention of this chapter to describe them all, but to describe two methods used in Elliot Lake. These are the ""fixed bed"", and ""moving bed"" systems, the condition of the bed during normal operation signifies the name of the system.Chemical and Physical Characteristicslon Exchange ResinThe resin used is a strange base Anionic resin, semi-rigid, and spherical in shape. The size of the wet resin is approximately 9007o between 20 and 40 mesh. Physically the beads of resin are broken early, but some have lasted over 15 years and are still in use."

Jan 1, 1989

By Robert B. Parsons

"A study recently completed by the Prospectors and Developers Association, assisted by the author and computerized mine models he developed, presents a strong case that present tax rules severely handicap the junior exploration company relative to the established producer. This month, Tax Notes briefly summarizes the highlights of the study and some of the Association's ideas which came out of the study.IntroductionIn the case of any industry, a particular project or investment will generally generate a more attractive after-tax rate of return to a tax paying entity than to a non-tax paying entity: the ability to shelter current taxable income with tax deductions related to the project or investment can present a definite advantage as compared to shielding taxable income in the future with the same deductions. But, this advantage is probably seen nowhere more clearly than in the mining industry where the tax rules allow for substantial up-front write-off's. Studies show that the junior mining company which is earning no taxable income currently can be seriously disadvantaged, compared to the mining company which is currently generating taxable profit and paying taxes. This is particularly disturbing when one considers the importance of the junior segment of the mining industry. One might well ask where the equity is, in a tax system which causes the junior company to look at a deposit and see rock in the ground, when at the same time the deposit represents a viable mine to an operating company. This inequity and the importance of the junior mining company have been recognized to some extent in the income tax legislation. In recent years, the expansion of the rules for deducting certain earned depletion allowances against any source of income, and changes to improve the flow-through share rules, have gone part way in helping to put the junior on a more equal footing with the operating company. But it is questionable whether or not these helpful changes to the tax rules have done enough to alleviate the apparent inequities in the income tax legislation."

Jan 1, 1985

By Zhang. L.

Ordered intermetallic PtSb had been synthesized by arc-melted and then sintering treatment. The electro-oxidation of formic acid on PtSb was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results are compared to those at a polycrystalline platinum electrode surface. It was found that PtSb intermetallic was catalytically more active than pure platinum according to the onset potential and current density. XRD and XPS technologies had been used to investigate the crystal structure and electron effect. We think formic acid decomposition on PtSb favors the reactive intermediate route and is not very much affected by the CO intermediate as compared to Pt.

Jan 1, 2005

By W. D. Fogwill, P. J. Clarke

"The Dawn Lake uranium deposits are located 340 km north of La Ronge, Saskatchewan, in the Athabasca Basin between the Midwest Lake and Rabbit Lake deposits. Four zones of uranium mineralization, called the ""11, 14, 11A and 11B Zones,"" lie within the Athabasca Sandstone, at the sub-Athabasca unconformity and in the basement.At Dawn Lake, approximately 100 metres of Helikian Athabasca Group clastic sediments overlie Aphebian Wollaston Group pelitic and calcareous metasediments and pegmatites. Uranium with some nickel, cobalt and copper, occurs near the sheared stratigraphic contact between calc-silicate gneiss and graphitic, pyritic pelite. The mineralization lies in an area of low magnetic susceptibility which is thought to represent a rock sequence lying stratigraphically high within the Wollaston Group. There is no obvious vertical displacement of the unconformity by faulting, despite considerable brecciation, shearing and slickensides seen in the basement rocks. This suggests horizontal displacement on steeply dipping wrench faults as the main tectonic control along the 11, 11A and 11B trend.Below the Athabasca unconformity, the Wollaston Group rocks are altered to fine-grained mixtures of clays, chlorite and silica commonly called regolith. Along the mineralized trend post-Athabasca fracturing and (or) compaction have occurred through this clay-rich alteration zone, causing the steeply-dipping primary foliation to become contorted. This ""crenulated"" horizon can reach depths of 35 metres below the unconformity and is thickest along fault zones in the calc-silicate rocks. The ""crenulite"" is a distinctive unit which at Dawn Lake is commonly found above pods of ore located deep below the unconformity.Much of the mineralization in the 11A and 11B Zones occurs above, beside and below the thickest part of the crenulated zone, although the crenulated rock itself contains negligible amounts of carbonate, pyrite and uranium. Intense vuggy alteration and collapse breccias are found in calc-silicate rocks deeper and to the west of the 11A and 11B mineralization. There are at least two ages of uranium deposition in the basement zones, shown by small bright cubes of ""pitchblende /"" overgrown and replaced by duller botryoidal ""pitchblende II. ""Sooty pitchblende and yellow secondary minerals are the result of still younger reworking.The geological setting of mineralization, along the contact between carbonate-rich calc-silicate rock and pyritic pelite, suggests that the uranium was concentrated at a pH/Eh boundary located between deeply weathered, carbonate-rich and sulphide-rich basement rocks."

Jan 1, 1986

By Ö Yilmaz

In this study, the behaviour of rock mass subjected to blasting load is investigated using three dimensional finite difference numerical modelling. In the analyses, Mohr-Coulomb failure criterion has been used for the characterisation of the rock mass strength. Stresses acting on the borehole boundary have been simulated by an exponential function which reaches its maximum within a short time and then falls to zero value in a considerable time period. The strain rate effect on the mechanical properties of rock material has also been taken into account in the analyses. Four different explosive-rock mass combinations have been studied to investigate blast induced damage zone. It has been observed that proposed equation for the dynamic compressive strength of rock material fits very well to general suggestions. Results have shown that blast damage analysis model recommended with this study is successful.

Aug 1, 2013

By F. Gaul, H. R. Manouchehri, A. Mosser

"Mining is a major energy intensive industry that contributes in consuming about 7% of the total world’s energy in which almost half in comminution. The underlying trait that drives energy consumption upwards appears to be somewhat persistent due to increasing in population, demands and growth rate. High grade resources have been/being depleted; consequently, low grade, high competent and complex ores with complicated geological structure are brought into perspective. For efficient extraction of values from such resources comprehensive multistage mining and processing strategies must be taken into account. Different treatment technologies, including ore sorting, must be considered to improve resource efficiency and productivity while taking into account the reduction in energy and water consumptions and related sustainability issues.The implementation of sorting technology in mining industry has a long past and its impacts on improving the overall efficiency of both mining and milling have been proven. However, the lack of complete understanding of its potential combined with ore complexity and low capacity of sorting machines have prevented the large scale application in mining industry. The application of X-Ray transmission sorting at Mittersill Tungsten Mine in Austria is presented and discussed herein. A technoeconomic analysis of the technology has revealed a significant potential of adding value to the concentration process. The rough feasibility study has given a strong feed-back on profitability and short time payback of about 2 years for the investment. Except the economic benefits the technology has positive environmental impacts. The potential for saving energy and water is large. The rough calculations have revealed that the energy saving can be up of 840MWh/annum. Furthermore, the ongoing cooperation between Mittersill mine and the sorting manufacturer is a good example on how the development of more competitive products, and product offerings, can be made."

Jan 1, 2016

By H. R. Manouchehri

"It is well understood that, apart from particle hydrophobicity, the flotation process is strongly influenced by the cell hydrodynamics. Once the chemical conditions were optimized and fixed, the flotation rate is essentially determined by impeller speed and the air flow rate.The collection efficiency in flotation is a product of collision, attachment and stability/detachment efficiencies. The collision efficiency for a given particle diameter is increased by decreasing the bubble size and bubble velocity as well as increasing the power input to the cell. The attachment efficiency, however, is defined by bubble size and its velocity. The detachment/stability depends on the relative magnitudes of the attachment force between the bubble and particles and the detachment force acting on the bubble-particle aggregates. For the particles having specific contact angle, the stability decreases as the energy input increases. Therefore, there must be an optimum energy dissipation to maximize recover of defined size fraction.A comprehensive laboratory study was devoted to determine the effect of power input in recovery of finely grind Cu-Ni bearing ore. Several flotation tests were conducted to define the hydrodynamic parameters for a laboratory scale Runge cell under different impeller speeds. An increase in flotation recovery of finely ground ore was observed when the impeller speed was increased from 450 to 1,200 rpm. The experimental results have shown increasing in water recovery and improving in flotation kinetics of fines by increasing the power input to the flotation cell. Implementation of the Wark flotation model to the experimental data revealed a good correlation between the experimental data and the model. For the particles having enough hydrophobicity the flotation rate increases by increasing the impeller speed due to a higher value for collision efficiency within the cell."

Jan 1, 2016

By D. A. Mackie, J. E. Rider

"Good belt conveyor design is the most often neglected detail in the engineering of a plant. This results in downtime from spills or jams and premature failure of equipment components. Careful layout and component selection will result in better operation, a cleaner plant and therefore lower maintenance costs.IntroductionDespite the availability of many excellent sources of data on conveyor design, such as the Conveyor Equipment Manufacturers' Association (CEMA) Manual, ""Belt Convyors for Bulk Materials"" , there continues to be repetitive errors made in design. Why? Certainly, there is no substitute for experience, but largely, classical errors in belt conveyor design is rather elementary and so the temptation to have the work done by relatively inexperienced designers is great. What that does is develop "" experienced"" designers who become incompetent through no fault of their own. It is hoped that this paper will supplement available design data, help those who are "" put into"" a design situation to better cope with their predicament, and ease the lives of plant maintenance personnel."

Jan 1, 1990

By L. I. Kiss, A. Larouche, V. Dassylva-Raymond

Control of the quenching capacity of the cooling water is of primary importance for maintaining the quality and recovery rate of ingots produced by direct chill casting. Industrially, this can be done using a cylindrical metallic probe undergoing rapid quenching by direct immersion in a reservoir filled with casting water. Such a test rig originally developed at Alcan Arvida Research and development Centre was modified and used to assess the role of key parameters affecting the boiling heat transfer. During the tests, the probe of the instrument undergoes the effects of different heat transfer mechanisms. An experimental study was performed in order to clarify the details of the probe-water heat transfer during rapid quenching. The heat flux along the surface was determined by mathematical modeling using the measured temperature signals, while the corresponding heat transfer regimes like stable and unstable film boiling, nucleate boiling and natural convection were identified by the analysis of high-speed video recordings. Aluminium

Jan 1, 2006

By J. G. Whellock, R. J. Phillips, J. W. Matousek, P. J. Marcantonio

"Stillwater Mining Company (SMC), a partnership of Chevron Resources and Manville Corporation, produces a copper-nickel, platinum-palladium flotation concentrate at its Nye, Montana mine. The concentrate is then toll processed in Europe. Recognizing the economic advantage of treating the concentrates at the mine site and of retaining this strategic resource in the United States, the Company commissioned Tolltreck International Limited and International Process Research Corporation to conduct pilot scale smelting tests with a flowsheet that would maximize metal recoveries while satisfying the environmental requirements of operations at Stillwater.Primary smelting was conducted in a single phase, 50 k W, submerged-arc, electric furnace. Refining the product mattes to copper-nickel ""white-metal""; containing approximately 2% iron, was accomplished in a Tolltreck, IV-litre, top blown rotary converter. Over-all platinum and palladium recoveries were approximately 99%; copper and nickel recoveries averaged 94%. INTRODUCTION(l-4)Stillwater Mining Company (SMC) a partnership of Chevron Resources and Manville, operates a copper-nickel, platinum palladium mine and concentrator at Nye, Montana, located in the valley of the Stillwater River, approximately, 100 km southwest of Billings. It is North America's only primary producer of these precious metals. The Stillwater area was mined for chrome ore during World War U and the Korean War, but it was not until 1961 that attention was drawn to the similarities between the Stillwater Complex and the Bushveld Complex of South Africa with its deposits of platinum group metals.A concentrated search for platinum was begun by Manville Corporation in 1967. Its presence, together with palladium, in mineable quantities was confirmed in the period 1976-1978, and the first partnership to develop the deposits was formed by Manville and Chevron in 1979. Anaconda joined the group in 1983, and in 1985 its share was purchased by Lac Minerals. In 1988 the interests of Lac Minerals were purchased by Chevron and Manville.The decision to develop the mine and build a concentrator was made in 1986. Construction began in the fall of that year, and the first concentrate was produced six months later, in March 1987. Underground mining is done in a two-shift, five day- week operation. Since startup, the concentrator has operated on a 24 hour/day, 7 day/week schedule, treating an average of 635 tonnes of ore per day and producing approximately 10 tonnes of concentrate."

Jan 1, 1989

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"Cu ore bodies commonly contain oxide Cu at the surface, with sulfide Cu content increasing with depth. The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Current practice of oxide Cu recovery involves sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors. CPS has shown to improve recovery of oxide Cu but has the following limitations: a) HSE issues with NaSH, b) high consumption of NaSH, and c) inability to recover certain oxide Cu minerals because they are refractory to sulfidization. The oxide Cu flotation is further complicated by the presence of certain non-sulfide gangue minerals which adversely impact both recovery and selectivity.Over the past eight decades, numerous collectors have been proposed and evaluated for the direct flotation (i.e. without sulfidization) of oxide Cu minerals, the most researched of which is alkyl hydroxamate. While there are numerous publications dealing with the fundamentals of interaction of alkyl hydroxamates with single minerals, there are few publications which discuss the practical aspects of alkyl hydroxamate use in ore flotation, particularly their use with sulfidizing agents. Case studies in this paper include methods to identify optimum combinations of sulfidizing agents and oxide collectors to maximize recovery for various types of ores. It was observed that some ores do not require any sulfidization, while others require at least partial sulfidization to improve efficacy of AHX. Depending upon the ore type and mineralogy, recovery improvement in the range of 5 to 15% units, over and above that achieved with CPS, has been observed with the use of AHX. For ores requiring high dosages of NaSH, it was shown that AHX can be used to reduce the NaSH consumption significantly. The challenges associated with the presence of non-sulfide gangue minerals in oxide copper ores are included, and the use of modifiers to alleviate the associated problems and enhance the performance of AHX is discussed."

Jan 1, 2016

By W. B. Evans, D. P. Taylor

"ANFO has two major disadvantages as an explosive low density and no water resistance. ANFO can be blended with more dense, water-resistant explosives to form ""Heavy ANFO"". The use of emulsion or slurry explosives as a matrix is an attempt to correct deficiencies on the basic ANFO while maintaining cost effectiveness.This paper will deal with four main topics.1. Product description, general properties, strengths and weaknesses.2. Technology of ""Heavy ANFO"" , the emulsion matrix concept and the range of products.3. Relative performance and economics in various rock types.4: Current status in Canada and worldwide, and the expectations for future use.IntroductionANFO has been in use for roughly three decades and remains the explosive of choice where conditions are suitable. ANFO has not become the universal explosive - despite its undoubted superiority in cost effectiveness - because it has serious flaws as an explosive. The most serious of these flaws are the low density and absence of water resistance in ANFO. Low density implies a low concentration of explosive energy in a borehole. The amount of energy available can be increased by. adding an energetic material, generally aluminum, or by drilling more holes. Both solutions add considerably to the over-all costs. The absence of water resistance in ANFO is inherent and can only be overcome by changing the fundamental nature of the product. The history of research in the explosives industry since the advent of ANFO is mainly the story of the various attempts to overcome one or both of ANFO's shortcomings.Many technologies and products have been developed to compete against ANFO, among them slurries, emulsion s and the so-called Dense ANFOs (ANFO with an extra nitroalkane liquid sensitizer). None of them was cost-competitive with ANFO so their market penetration has been limited to wet holes or specialized applications. The exception to this result is Heavy ANFO. The aim here was to have the best of both worlds, the high density and water resistance of emulsions or slurries plus the low cost of ANFO. The concept is very simple. ANFO is about 50 % air, roughly 30% in the prills and 700,10 between the prills . The air in the prills provides the necessary sensitivity but the air between them is waste volume. If one fills this volume with a high density, waterproof product, the resultant mix will be denser and more water resistant than ANFO and with very little added cost. This basic concept was invented by B. Clay in the 1970s and is covered by Canadian Patent No. 1 115 959. The water resistance and/or density of the mix can be tailored by changing the emulsion level. Because Heavy ANFO is relatively inexpensive while providing good in-hole densities and water resistance, it can compete successfully against all other bulk products. It competes against ANFO and Al / ANFO by allowing pattern expansion and reducing over-all costs while it competes against emulsions and slurries on price."

Jan 1, 1987

By J .. A. Nemes, I. Ragai

This paper discusses one of the common problems associated with sheet metal forming processes, which is spring back. The materials presented here, stainless steel 410 and Inconel 718, are commonly used in aerospace applications for their superior material properties. Standard tensile tests were performed to determine their tensile properties, as well as material anisotropy. In addition, the effect of anisotropy on springback was assessed experimentally through simple multiple-bending experiments in different directions to the rolling direction. Finally, draw-bending experiments were carried out to study the effect of forming conditions, such as blank holding force, on the final springback angles of the formed parts. For both materials, it was found that the R-values measured for different sheets exhibited variation. However, the specimen orientation does not have a large effect on material tensile behavior or springback angle for simple bending. For the Inconel 718 specimens, the springback angle slightly increases with each stage of deformation during multiple bend experiments. The effect of the blank holding force on springback angles was also examined and found to have a significant effect on thin specimens.

Jan 1, 2006

By Robert B. Parsons

"It is generally acknowledged that Canadian and foreign-based mining companies are spending relatively fewer dollars in Canada and more dollars abroad than was the case not many years ago. It is common to see the Canadian tax system being fingered as one of the causes in this shift in direction. However, if one takes the time to peel away the surface of our tax system, and to probe a little deeper into its substance, it will be found that the Canadian taxation of mining is generally quite competitive. IntroductionCross-border shopping in the mining industry? - Absolutely! Economics 100 teaches that dollars are votes in the capitalist system, and mining companies are going to cast their limited number of votes where they can achieve the highest return at the least risk. The Canadian consumer knows that taxes are a major factor in cross-border shopping, and mining company executives know that the same tenet holds true in their industry. Unfortunately, mining operations are subject to such a bewildering array of tax rules that making an intelligent decision is not always an easy matter.Statutory Tax RatesConsider, for example, the ""statutory"" tax rates shown in Table 1. (Statutory tax rate in this table refers to the simple sum of federal and provincial tax rates on profits as specified in the tax legislation.) Looking only at the total statutory tax rates (such as 66070 for Manitoba) , one might quickly observe that the Canadian mining industry is subject to a truly onerous tax regime, especially as compared to the United States where statutory tax rates can be in the 34% range."

Jan 1, 1992

By Frédéric Flament, Mary Goldman, Gille Barbery

"Pilot plant testwork on autogenous and semi-autogenous grinding was conducted at the Centre des Recherches Minérales du Québec (CRM) to investigate the effect of ball addition, solids concentration in the feed, specific energy consumption and feed size distribution.A mathematical model that incorporates breakage and surface mechanisms of loss of mass was developed to predict load size distribution of autogenous and semi-autogeneous mills. An empirical model was used to predict product size distribution of autogenous and semi-autogeneous mills.IntroductionAutogenous (AG) and semi-autogenous (SAG) grinding circuits offer potential capital and operating cost savings when compared with conventional grinding. Empirical relationships have been developed to calculate specific power consumption for SAG mills using pilot plant test results (Mular et al., 1989; Barrett and Allan, 1986). Empirical models can be obtained from plant practice data but are applicable only to the particular ore and set of operating conditions used in the model. Grinding mechanisms have to be taken into account in order to develop a model that can be applied to different ores and mills.In AG and SAG, the ore itself acts as grinding media, with the finer sizes being crushed by the coarser ones. Surface mechanisms of loss of mass, in which the inner core of the particle remains intact, also take place. In SAG milling, the effect of balls also has to be taken into account. The role of each one of these mechanisms changes with particle size and the model has to account for such changes."

Jan 1, 1991

By Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the North American database.

May 1, 2006

By Yve Aymong

"The objective of this paper is to help readers benefit from the practical experience of persons who have been engaged for several year s in the testing and repair of power transformers. Power transformers are known to be reliable pieces of equipment with expected usage of 25 to 30 years, but simple problems such as leaking radiators, or a bad contact on a tap changer, could shorten the life of a transformer. To ensure a longer life span, transformers should be checked on a regular basis.What is a Power Transformer?It can be a 90 MVA transformer for Hydro-Québec or a power transformer can be a 500 KVA unit in a small hospital. Generally a power transformer is an oil -filled type of 3 to 5 MVA. It can also be a dry type transformer, that should be treated in the same manner as oil-filled transformers, and some of the tests explained in this paper also apply."

Jan 1, 1984