Search Documents

By S. C. Livanou, S. P. Tampouris, E. N. Zevgolis

In ferronickel (Fe-Ni) production from oxidized nickeliferous ores, mechanical losses of ferronickel in the slag are reduced by magnetic separation. Slag from the electric furnaces (E/Fs) contains 0.16% Ni. Its magnetic separation gave a pre-concentrate with 0.76% Ni, weighing approximately 6.5% of the feed. Nickel recovery was 29.7%. This pre-concentrate was then treated in a second (concentration) plant. Concentration treatment involves screening, crushing and magnetic separation. A pre-concentrate with 0.76% Ni gave a magnetic concentrate with 2.58% Ni and a non¬magnetic part with 0.35% Ni. Smelting of the non-magnetic part without the addition of a reduction agent in a laboratory electric arc furnace, gave a ferronickel alloy with approximately 20% Ni and a slag with 0.16% Ni.

Jan 1, 2005

By B. R. Rakishev

Balanced development of mining works at all the benches of a working zone by use of the excavator-automobile complex is achieved by transition to the technology of the bench excavating with cross panels by the two-sub-bench scheme with the changing levels of the working platforms (is patented in Kazakhstan). In deep quarries realization of this technology will allow to reduce the current volumes of the stripping ore excavation by 10?15 % and more, to increase the opened reserves of minerals by 20?50 % to decrease volume of mining-capital works for construction of stripping excavations by 2?4 times and to provide efficient use of powerful excavator-automobile complexes.

Aug 1, 2013

By A. M. Cormie

Introduction The purpose of this paper is to give a brief, general outline of mining practices at Torbrit Silver mine. The geology of the mine is touched on as it is felt that a rough picture of the geology will result in a clearer understanding of the mining methods employed. The main part of the paper deals with mining methods and a section is included on haulage. Development practice is mentioned only briefly. Torbrit Silver Mines, Limited, a subsidiary of Mining Corporation of Canada, is located in the Alice Arm area of northern British Columbia. Access to the mine is by boat to the village of Alice Arm at the head of Alice arm, then truck road, following the course of Kitsault river for 18 miles in a northerly direction to the plant site. The main portal is a further two-thirds of a mile along the course of the river, at approximately the same elevation as the plant, 1,014 feet above sea level. Geology The ore occurs in a massive, irregular-shaped quartz-barite body replacing a folded area in a series of volcanic breccias, tuffs, and flow rocks locally referred to as 'green-stones'. A series of parallel, nearly vertical, fine-grained basic dykes cut across the formation at right angles to the strike of the ore belt over a horizontal distance of 140 feet. The whole of the quartz-barite vein material, which ranges up to several hundred feet wide in places, carries silver values but commercial grade is confined to lenses and shoots where there have been more than usual concentrations of native silver and silver-bearing minerals. The ore-bearing structure plunges at approximately 25 degrees along an axis striking roughly N.65°W.

Jan 1, 1951

By P. M. Shibley

"IntroductionMine drainage, surface. drainage and process liquors are the principal mine and mill effluents. The quantity and quality of these flows varies according to mineralogy, type and scale of mining, the process, tailing disposal, local ground conditions and climate.Typical contaminants remaining after solids sedimentation are colloidal or semi-colloidal particles, acids, alkalis, metals in solution, cyanides and thiosalts. Environmental regulations and guidelines have been issued in detail by the appropriate government agencies and will not be reviewed here. Revisions and additions are being made as our comprehension and abilities increase. Some contaminants of consequence have not been specifically regulated as practical treatment technology has not been identified. Thiosalts fall into that category as do the derivatives of the first stage of cyanide oxidation - cyanates.Most mining activities have present or foreseeable water treatment requirements. Because process economics can be adversely skewed by the environmental factor, the acknowledged objective of every operation must be to identify and anticipate those requirements.The evaluation and selection of water treatment techniques for mine-mill applications is complicated by the fact that most mine-mill effluents are high volume, dilute and chemically complex systems. Treatment processes applicable to most contaminants are: chemical or biological oxidation; neutralization and/or precipitation; liquid/solids separation. Other processes such as ion exchange, electro-deposition, foam fractionation, freeze crystallization and reverse osmosis offer the possibility of selective removal or concentration of contaminents. The latter tediniques, representing a slightly higher level of technology, are less suited to the large, low value flows usually encountered in the mine environment."

Jan 1, 1989

By M. Rafieazad, P. Fathi, X. Duan, M. Mohammadi, A. M. Nasiri

"Direct metal laser sintering (DMLS) is a metal additive manufacturing technology that creates highly complex components by fusing metal powder into a solid part. In this study, the impact of surface roughness on corrosion resistivity of AlSi10Mg_200C alloy manufactured through DMLS was investigated. The as-printed DMLS-AlSi10Mg _200C alloy was subjected to various surface finishing processes including grinding and sandblasting. The corrosion performance of the surfaces was then evaluated using potentiodynamic polarization testing and electrochemical impedance spectroscopy (EIS) in a 3.5 wt.% NaCl solution to mimic seawater environment. Surface characterization and corrosion morphology of the samples were assessed by Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) spectroscopy. The results of this study show that the surface finishing process and the resultant surface roughness has a significant impact on the corrosion resistivity of the DMLS-AlSi10Mg_200C alloy in the seawater environment.INTRODUCTION Direct Metal Laser Sintering (DMLS), also known as Selective Laser Melting (SLM) (Sames, List, Pannala, Dehoff, & Babu, 2016), Laser Beam Melting (LBM), or Laser Metal Fusion (LMF) (Herzog, Seyda, Wycisk, & Emmelmann, 2016), is an additive manufacturing process that utilizes a precise, high-power laser to micro-join powdered metals and alloys layer by layer to form almost fully dense and functional components in three dimensions from the 3D computer-aided design (CAD) data. Complex geometries not possible with conventional manufacturing processes can be readily manufactured with high accuracy using the DMLS process with no need to time-consuming tooling."

Jan 1, 2018

By S. Sundararajan, J. Brousseau, P. Bocher, M. Galopin, N. Barka

This research is committed to the prediction of the hardness profile produced by induction heating, using a computer-modeling software. The paper presents the simulation of the induction hardening process to analyse the sensitivity of the induction parameters on the hardness profile of a low alloy steel specimen. The developed numerical model includes the coupling effect between electromagnetic and thermal fields, and takes into account the non linear behaviour of the material properties. The study applies an enlightened experimentation method to build the feasible domain of the process and to achieve predictive empirical modeling. The ultimate goal is to replace the trial and error method that is usually used for the development of new parts, by costless experiments with the numerical model. Further development of this approach will lead to the computation of the residual stresses and finally to the assessment of the mechanical properties of the part. The end result will be the ability to shorten the development time and to improve the quality of the hardened part.

Jan 1, 2006

By Charles Tkaczuk

In order to remain competitive the mining industry must keep up with changes in technology. Many innovative technologies from the mining perspective are commonplace in other industries. A ?Global? review of technologies will often reveal existing technologies that can be innovatively applied in the mining industry. Industries, which are rife with proven solutions include, medicine, biotechnology, security, manufacturing, telecommunications, etc. This paper addresses the communications aspect of mining where greater productivity, lower costs and the ability to quickly react to mining related events is obtained through an increase in remote monitoring and operating control. A review of the communications systems in place globally reveals technologies that, with minimal modification, can be immediately applied to the mining environment. We discuss the concept, advantages and implementation of existing communications technology from an industry that is not usually associated with the mining industry. This technology will form the basis of a solid platform on which can be built a state-of-the-art process monitoring, control, and communication system. This lays the groundwork for providing one solution to the underground mining industry?s most difficult problem, establishing a reliable, maintainable and cost-effective underground bi-directional wired/wireless data, video and analog communications system. We need look no further than our own doorsteps to find such a solution. The cable that you see coming from the simple green or brown box on the boulevard into your home contains hundreds of television broadcast channels, FM radio channels and data channels. And if you have a set-top box, you are in control of it all. The Cable Television Broadcast Distribution System suppliers of today are at the leading edge of converging all the different methods of communications onto a common carrier, coaxial cable or fibre optic cable. There is no fundamental difference between providing a reliable communications network to a city/neighbourhood/home/personal computer than there is to a mining operation/underground level/equipment or person. The principle is the same. Only the application is different. Realizing this, we can capitalize on the efforts of other industrial sectors, to solve our communications problem. Where else can you find a solution to a problem that is mature, having been developed with the input of thousands of engineers, and having hundreds of millions of dollars spent on research and development, manufacturing, distribution, global presence and engineering support?

May 1, 2003

By F. G. Smith

Abstract Laboratory methods are now in use whereby the temperature and pressure during the crystallization of hydrothermal minerals can be determined. The techniques include the use of the decrepitation method of studying liquid inclusions, and electrical measurements of pyrite. The determinations are sufficiently accurate that the data can be used in solving a variety of ore deposition problems. Within the last year, several new laboratory techniques have been developed in the Geochemical Laboratory of the Department of Geological Sciences, University of Toronto. The results of several tests of ore by these methods have proved to be useful in treating some problems which previously were considered unsolvable. It is now possible to determine the temperature of deposition of most of the minerals in a hydrothermal ore deposit, also the depth below the surface during deposition. Measurements can also be made of the reopening history of a complex ore. The temperature-pressure determinations depend upon the fact that minerals deposited from a hydrothermal solution always trap a small amount of the solution at the time of crystallization. The solution, being predominantly composed of water, has a density which depends upon the temperature and the pressure prevailing during crystallization. After ore deposition is complete, erosion and isostatic uplift finally exhumes the vein. During this slow fall in temperature and pressure, the solution contracts and a gas bubble appears. If the trapped solution in the mineral is examined, the gas-liquid ratio records the density of the solution at the time the mineral was deposited (except for a slight change in the volume of the mineral). The thermal expansion and compressibility of water and water solutions are known to a sufficient degree that, if the gas /liquid ratio can be determined, the temperature-pressure relations during deposition can be calculated.

Jan 1, 1949

By C. J. Sullivan

It is of importance, in prospecting, to distinguish ores of magmatic origin from those derived by the meta-morphism and granitization of source rocks and from those accumulated in certain sedimentary facies. The magmatic ores, which are characterized by their occurrence along fault structures, may be associated with volcanic (including explosive) phenomena. Heat effects are local. The magmatic sequence is well de-fined: kimberlite, with diamond pipes; ijolite, with carbonatites; peridotite, with nickel deposits; norite, with nickel-copper deposits; and diabase-gabbro, with copper-zinc deposits. These deposits are characteristic of Precambrian shields, where a thick sialic crust may rest on basic to ultrabasic magma. The sequence is resumed in the Paleozoic terrains (in a broad sense), with monzonite porphyries and associated copper, copper-gold, and cop-per-lead-zinc deposits.

Jan 1, 1962

By B. D. H. Knights, M. A. W. Bryson

Flotation of PGM ores, specifically UG-2, presents a number of technical challenges. These centre on the prevalence of chromite. Subject to over-grinding, chromite is primarily recovered to the flotation product through entrainment. This is of unique concern as it must be kept below a threshold for downstream smelting, with significant operational and monetary penalties being imposed should it exceed this concentration. A number of strategies have been developed to maximise PGM recovery in the presence of this unwanted contaminant. Specialised flowsheets form a vital basis and advanced control algorithms further enhance PGM recovery while minimising the recovery of chromite. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By Peter S. Jack

"IntroductionTHE ORES treated at the concentrator of the Britannia Mining and Smelting Company, Limited, Britannia Beach, B.C., have always contained some lead, but it was not until 1950 that the combination of lead headings and lead price was such that recovery of this metal at Britannia became worthwhile. In that year, with the mining of a new orebody, the lead in the mill feed was raised from 0.07 per cent to 0.15 per cent. Chalcopyrite, sphalerite, and pyrite concentrates are produced by flotation at Britannia, •and 95 per cent of the lead in the mill feed reports with the chalcopyrite concentrate, so that the rise in lead headings was reflected almost wholly in the lead content of the copper concentrate. In 1950, investigation was started to determine if some of this lead could be recovered economically."

Jan 1, 1953

By E. Ettles

This paper features some of the spectacular new advances in the fields of fluorescent penetrant inspection and magnetic particle concentration. Casting fractures in the various stages -before the repair, during the repair and in the completed repair -using the cold process method will be discussed. This cold method of repair eliminates problems of pre-heating and cooling and the stress factors that are involved in any heat repair.

Jan 1, 1971

By J. F. Shirley

"Very seldom, if ever, is a molybdenite by-product plant operated exactly the way the process design engineer visualizes it. The best thing the design engineer can do is provide a sound, basic circuit with enough room and flexibility in order that the operating staff can make the necessary modi fi cations to optimize the process. The plant, with minor modifications, should be capable of handling more than one process. This is especially true when the client is having the plant designed for a new process.The writer would like to propose the following ten ""rules-of thumb"" for designing by-product molybdenite plants where the molybdenite is floated out of a copper concentrate. The term rules-of-thumb is used, because there are probably valid reasons for not using one or more of them in a particular plant design. In fact it was 1980 before the writer was all owed to start up a plant where all of these rules were honored in the plant design. This was after 19 years of experience in the design of molybdenite by-product processes and plants. The main reasons for not following the rules are available capital, available space, and the client's experiences based on pilot plant and laboratory test results."

Jan 1, 1981

By Z. F. Lodhi, J. H. W. De Wit, H. A. Terry

Zinc and its alloys have been extensively used as replacements for Cadmium coatings in aeronautical and automobile industries. Zn alloys with low Co or Fe have been highly investigated but coatings with higher amount of Co are very difficult to achieve due to anomalism associated with these coatings. Anomalous Zn-Co-Fe alloy is a relatively recent addition to the family of Zn alloys. It is found that the addition of Fe in the electrolyte assist in overcoming the anomalism. In this research Zn-Co-Fe alloys especially with higher amount of Co (>15%) and Fe (~1%) are investigated, after overcoming the anomalism associated with its deposition, and the corrosion resistance is compared with pure Zn and Cd. It is found that an increase in Co to higher than 25 % accounts for a shift in the OCP to a level near Cd yet keeps it electronegative to steel. The coating shows superior corrosion resistance, in terms of its sacrificial and barrier properties in 3.5% NaC1 as compared to Zn and Cd.

Jan 1, 2006

By A. Scheltema Beduin, M. Kalisch, E. Floch, R. J. Dijkhuis, H. J. Oterdoom

In metallurgical copper production, the traditional aim is to increase recovery of copper to the maximum. SMS Siemag (SMS) has supplied numerous furnaces for this application. New targets are to make sure end of line products are as safe as possible with respect to health and environment, and to maximize raw material utilization. This means a for example a minimization of leachable metals in slag, so it can be safely used as a construction material, and either a targeted concentration or fixation of volatile compounds, such as arsenic. Currently, 2 process routes are generally applied for slag cleaning. The first is grinding followed by flotation, and the second is slag cleaning in an (electrical) furnace. Popularity of both options has fluctuated over the years, and currently the milling-flotation seems to be the more popular option. In this article some of the advantages and disadvantages of both methods are described, and especially how long term environmental policies could have an impact on the decision which process route to choose. Finally, this article will describe some of the developments SMS is working on in pyrometallurgical slag cleaning that could influence the direction for the design of the copper plant of the future.

Jan 1, 2014

By H. E. Johnston

There are currently a number of options in terms of plant feed comminution tests: Bond work index tests, JK drop weight and SMC tests, SPI, low impact crusher work index tests, to name a few. However, information regarding specific energy requirements for regrind mills is often requested, which can be difficult or very expensive when only a small mass of concentrate is produced from bench-scale flotation tests. This research was aimed at developing a test methodology that would produce a similar result as an IsaMill Signature Plot but require less sample mass allowing for preliminary estimates of regrinding power at a lower cost. Initially, the laboratory test methodology was completed on a single sample in comparison to the IsaMill Signature Plot for that sample. Results indicated a very good correlation between the laboratory tests and the IsaMill Signature Plot for this sample, though some parameters did impact laboratory regrind mill efficiency. The developed methodology is subsequently being applied to a range of concentrates, investigating a range of material particle sizes and material types, in comparison to a full IsaMill Signature Plot on the same sample. This new test procedure has been called ‘The Eliason Test’.

Jan 1, 2014

By J. Stachulak, M. Scobie

"This paper addresses the occurrence and indicated causes of conveyor fires in North American and European underground mines. Some significant convey or fires which have been experienced in recent years in Canadian hardrock mines are then reviewed. The nature of existing conveyor monitoring technology is considered in the context of such fire hazards. Experiences with new monitoring technology recently installed at several conveyor sites at Inca Ltd. mines are then reviewed.IntroductionFires associated with conveyors have long been recognized as a serious hazard in underground coal mines. Recently, however, there have been some significant conveyor fires in Canadian underground hardrock mines. These offer important evidence as to the nature and causes of potential hardrock mine fifes. They also warrant attention with a view to improving over-all mine design, ventilation and emergency preparedness.In addition, a new era in mine communications and monitoring technology has been entered which should offer improved capability to protect against such fires. This paper was motivated by the need to understand the causes and mechanisms of conveyor fires in order to improve their safety. This should be possible through implementing more effective monitoring systems, as well as improving conveyor design. Underground mines are becoming more intensively mechanized, with less human surveillance of equipment and a greater dependency on remote monitoring systems."

Jan 1, 1992

Experimental determination of the response of an AG/SAG mill treating two components of significantly different impact resistance is challenging for two main reasons: firstly, small scale laboratory tests have yet to be confirmed as valid representations of the full scale milling environment, and secondly pilot plant testing requires 10-20 tonnes of ore per scenario which precludes the use of drill core, rendering the process very expensive. In order to mitigate these difficulties, modelling was considered as a potential way forward. However, as the JKSimMet AG/SAG model currently has no capacity to simulate the interaction of two ore types with differing impact resistance, density and/or feed size distributions, an alternative modelling approach was developed. This approach aims to essentially calibrate the AG/SAG process under a set of given conditions, for which survey data and the ore properties of the main components in the feed blend already exist. This paper describes a new conceptual model, which provides a simplified approach for investigating the multi-component behaviour of two ores of differing hardness/SG in a given AG/SAG milling environment, and which can potentially be used for scale-up from laboratory/pilot testwork and geometallurgical estimation of throughput.

Jan 1, 2012

By J. Dupre, A. Gontcharov, H. Pepin

Produced by the conventional TIG welding CMSX-4 welds had been studied. It was demostrated that microstructure of welds depended on filler materials, welding parameters and joint design. Epitaxial solidification of CMSX-4 clad deposits produced a directionally solidified structure while welding with the similar filler material. Defects free clad welds were obtained by TIG welding without preheating using similar and dissimilar filler materials.

Jan 1, 2006

By P. L. Wright

"This is a brief history of the development of the mining project, with a description of the proven geology. The paper describes how the experiences gained progressively demanded change in the mine design. The equipment used is described, together with methods of working. Interesting facts have been proved regarding gas emissions and roof. supi;iort. The. working cycles evolved are completely flexible m operation and lend themselves to maximum utilization of the most productive units. The two underground mines are compared, showing the variance in conditions already experienced. Programs currently in operation to improve standards and production are: the training of miners, maintenance men and officials; experiments in floor consolidation and continuing roof support trials; and the effect of comparative stability of working crews on the performance of the operation."

Jan 1, 1973