Search Documents

By Jie Zhu

Coal bumps are a special form of release of geologic strain energy that has already been one of the most dangerous hazards to underground mining safety in China. A number of coal-bump models have been developed to quantify coal failure under assumption that a bump is a kind of non-gas induced outburst. However, some technical experts in charge of micro-seismic and gas monitoring have found unusual gas emissions before and after bump, which suggests that it is possible for gas to trigger coal bumps. Considering the coal reservoir as geological body composed of the coal matrix and gas, a new model based on Lippmann?s bump model is proposed to understand the initiation of coal bumps. The redistribution zone from excavation of a roadway has been calculated and analyzed regarding its relation with mining depth. It is shown that high gas pressure may push the coal seam to overstep the critical state due to extension of the plastic disturbed zone, and this is harmful to the stability of coal seam. This model successfully explains the bump phenomena of the Xinzhouyao mine at shallow depth.

Aug 1, 2013

By R. R. Rogers

Introduction The subject of cathodic protection is not new. In 1824 Sir Humphry Davy, in publishing the results of his investigations for the British navy, pointed out that copper could be protected from sea-water corrosion by connecting it electrically with zinc or iron. Since that time much work has been clone in this field, particularly in the protection of metals from the action of sea water, neutral brines, and treated and untreated waters. Special mention should be made of the successful protection of underground pipe-lines which formerly were badly corroded by the water in the ground. So far, magnesium alloy and zinc anodes have been the most popular. However, fairly recent work has indicated that aluminium anodes will give good service under certain conditions. The principle of cathodic protection has been applied extensively in coating steel articles with zinc and in cladding aluminium alloy sheet with pure aluminium. A valuable discussion of the fundamentals and applications of cathodic protection recently was presented in the Corrosion Handbook. A useful list of references was included in the article.

Jan 1, 1949

By J. W. Cox, W S. Jones, A E. Chase

For a long time the Oil Industry has been looking for a logging tool which can determine the quality of the cement job behind casing. Older methods such as Temperature Surveys and Radioactivity Surveys might detect the presence of cement behind the casing, but short of production tests, it was impossible to tell that the producing zones were adequately sealed off from adjacent zones. A new logging method, which is called the •Cement Bond Log, operates on the principle that a sonic pulse transmitted by the casing is greatly attenuated when the casing is strongly bonded to an outer annulus such as cement. The down-hole tool consists of a source of sonic energy which is detected by a receiver situated a few feet away from the source. The amplitude of the detected energy is measured and the resulting signal transmitted to the surface where it is recorded versus depth. Amplitude is a function of attenuation and thus the log is readily interpreted.

Jan 1, 1961

By Curtiss O. Ehrsam, M. Naseem Mian

Alaska’s Red Dog Mine is strengthening its position within Cominco’s “Vision 2000”strategic plan by continually improving quality and quantity of production while reducing costs. Red Dog has evolved into a stable and mature operation, after six years of milling experience. A high grade, partially oxidized orebody in the severe Arctic environment, along with competing producers in a volatile metals market, are the continuing challenges facing Red Dog. The Red Dog Mine is striving to meet these challenges with emphasis on operator training combined with creative systems development and increased production. This paper describes developments in operations along with future plans.

Jan 1, 1996

By S. Gheibi, H. S. B. Duzgun, N. Dadashzadeh

It is widely recognized that there are various uncertainties in the analysis of rock slope stability owing to inadequate information for site characterization and inherent variability and measurement errors in geological and corresponding parameters. Therefore, reliability-based approaches that allow the systematic and quantitative treatment of these uncertainties have become a topic of increasing interest in rock slope engineering. There has been extensive reliability analysis of rock slope stability in the literature. However, all of these analyses are based on the First-Order Reliability Method (FORM). The probability of failure of a rock slope in the First-Order Reliability Method is provided by a linear approximation of the failure function. The FORM is most commonly used because it is efficient; its accuracy, however, deteriorates when the nonlinearity of limit-state function increases. A better approximation of the failure function can establish a more accurate value of the probability of failure. The Second-Order Reliability Method (SORM) overcomes this drawback with a cost of lower efficiency in terms of the number of function calls and computation expenses. Despite considerable studies of the application of the SORM in other engineering fields, a few attempts have been made in the slope stability studies. In this study, a recently published Second-Order Reliability Method with First-Order Efficiency (SORM-FOE) is implemented on a selected rock slope in Amasya, Turkey. The SORM-FOE overcomes the low efficiency of the SORM by decreasing the number of function calls. The probability of failure of both FORM and SORM-FOE are obtained and the results are compared. It is shown that, in high value of failure probability, SORM’s do not significantly affect the analysis and design. However, in very low failure probability, the discrepancy between FORM and SORM-FOE becomes pronounced. It is also shown that, where the second order methods are required, the SORM-FOE is more efficient than the conventional curvature fitting methods in terms of computational costs.

Jan 1, 2015

By Lev Filippov, Saeed Farrokhpay

"Flotation process has had less success to recover nickel from laterite ores. Nickel in laterite ores is often finely disseminated in various minerals in very fine size. Therefore, fine grinding should be used to liberate nickel containing particles. Particles resulted from fine grinding are often very fine, and recovery of such particles is generally low using conventional flotation methods. One option to overcome this problem is enhancing the particle-bubble interaction by increasing the particle size and forming flocs. Selective flocculation of fine particle can be therefore the key to enhance the flotation performance of low grade laterite ores.INTRODUCTIONThe majority of the world’s nickel resources occur as laterite ores which are complex, low grade and expensive to treat using conventional smelting and high temperature and/or high pressure autoclave methods (Xu et al., 2013). While about 70% of the nickel resources are contained in laterites, only 40% of the world’s nickel production comes from these ores. Researchers have tried to improve the nickel laterite flotation recovery by using a number of feed preparation techniques. For example, in a study on a laterite ore sample from Australia, flotation tests on a narrow sized fraction of 38-75 µm resulted in only a small increase in the nickel content, from 1.0% to 1.4% (Quast et al., 2015a). In fact, no physical separation technique (including flotation) has been able to dramatically upgrade nickel in laterite ores (Quast et al., 2015b). Thus the challenge of processing low grade nickel laterite ores still exists. This paper aims to explore the possibility of applying selective aggregation in pre-concentrating of valuable minerals in nickel laterite ores."

Jan 1, 2016

By Jinsuo Zhang

Investment in coal resource development is affected by a variety of uncertain factors. Investors can make a flexible, strategic decision to achieve the value of risk implicated in those uncertain factors. Therefore, based on real-option theory, we identified key uncertain factors that affect a coal resource investment project, and revealed the formation mechanism of option value in coal resource developing investment project. Then, a multi-factor decision making model was established for a coal resource development investment project with random changes of coal price, interest rate, convenience yield and production cost. Finally, we tested the model and analyzed relevant parameters by applying living data. Our results indicate this model reflects the value of risk implicated in uncertain factors for coal resource development investment, and is able to determine a critical point of decision making change when coal price and production cost varym respectively. By means of parameters analysis, the convenience yield has a positive effect on the project value. The interest rate has a negative effect.

Aug 1, 2013

By Qing-hua Tian, Xue-yi Guo, Fei Li

A novel process for the preparation of a-Al2O3 from secondary aluminum dross was studied. Factors including alkali dross ratio, salt dross ratio, smelting temperature, smelting time, leaching temperature, leaching time, and the solid-liquid ratio, which possibly influence the transfer of Al into water were studied, and the feasibility of using seed precipitation as a treatment technology of the leachate was discussed. The optimum condition of the process was determined as: alkali dross ratio 1.3, salt dross ratio 0.7, smelting temperature 500°C, smelting time 60min, leaching temperature 60°C, leaching time 30min, solid-liquid ratio 1:4. The results show that using the seed precipitation method, the leaching of aluminum reaches 92.71%, demonstrating the technique as a feasible and effective treatment technology of the leachate.

Jan 1, 2011

By Wei Huang, Anh V. Nguyen

"Potash flotation is an industrially proven success of flotation of soluble salts, but its collector adsorption mechanism remains elusive. In this paper, specific ion effects in NaCl-KCl flotation with carboxylate collectors were investigated. Flotation recovery and contact angle were determined as a function of brine composition of NaCl and KCl. The experimental results have shown that wettability of KCl and flotation of the soluble salts with laurate collectors were dependent on brine ion composition. Specifically, adding Na+ to brines decreased hydrophobicity of KCl crystals and their flotation recovery. Both KCl and NaCl could be floated with laurate collectors. However, flotation of NaCl was greatly enhanced by adding K+ to brine whereas flotation of KCl was significantly suppressed by the presence of Na ions. The decrease in KCl recovery upon adding Na+ is attributed to the counter-ion binding in the pulp. The flotation recovery enhancement of NaCl in the presence of K+ is explained by two effects: 1) increasing K+ concentration leads to a better dispersion of collector colloids in the pulp and 2) K+ enhances the collector adsorption at NaCl crystal surfaces. The water affinity matching rule can explain the specific ion binding behaviors and supported by the SFG spectroscopic results.INTRODUCTIONPotassium is an important fertilizer. Its primary source comes from potash ores, which are a mixture of sylvite (KCl), halite (NaCl) and many other complex double salts such as carnallite (KCl·MgCl·6H2O), alkali nitrates such as KNO3 and NaNO3, and sulfates-langbeinite (2MgSO4·K2SO4) with water-insoluble minerals such as clay and carbonate minerals. Previously, these salts were recovered with a lengthy hot leaching method, with further crystallization of potassium salts from saturated saline solutions. Selective flotation has been preferred since 1940s. Various collector adsorption mechanisms have been proposed soon after the industrial introduction of potash flotation. These include the formation of the insoluble compound model (Halbich, 1933; Singewald, 1961), an ion exchange model (Fuerstenau and Fuerstenau, 1956), a heat of solution model (Rogers, 1957), the surface hydration model (Schubert, 1988), the surface charge model (Roman, 1966; Miller et al., 1992), the interfacial water structure model (Hancer and Miller, 2000) and the colloid adsorption model (Leja, 1983; Burdukova and Laskowski, 2009). Most of the early exercises attempting to propose a unified rule on collector adsorption mechanisms can be seen as heroic endeavors due to the consideration of a vast number of salts in the pulp including alkali halides, nitrates, and sulfates, even the practically insoluble heavy earth metals. Additionally, several types of surfactants with different polarization features and alkyl chain length have been employed. As for the recent models, due probably to the preferential application of long chain amines as collectors in industrial potash flotation, most researchers are only devoted to collectors with low polarization features like amines and sulfonates (Hancer and Miller, 2000; Du et al., 2014). Collector adsorption mechanisms are therefore proposed based largely on a neglect of carboxylates as collectors. However, carboxylates remain an important collector type in soluble salt flotation systems where both salt minerals can be floated using anionic collectors and cationic collectors. Fatty acid type collectors are still one of the widely used collectors for soluble salt flotation and also one of the first to be applied on an industrial scale for the separation of potash ore (Hernáinz et al., 2003; Titkov, 2004). Here we examine some recent models that are relevant to our study to reveal a long neglected specific ion binding effects in potash flotation."

Jan 1, 2016

By Ki-Bok Min, Bona Park

"In spite of the applications of DEM models to emulate the elastic modulus, Poisson’s ratio and strengths of isotropic rock in laboratory scale, extensions to anisotropic rock and larger engineering scale still have many challenges to overcome such as robust verification and validation against observed field case. In this study, a discrete element modeling was performed in order to represent a transversely isotropic rock such as shale, and the upscaled model was applied to foundation and borehole problems using PFC2D. The applicability of the upscaled rock mass model was verified by an analytical solution. The DEM modeling of stress redistribution induced by an applied surface line load compares well with Boussinesq’s isotropic solution and anisotropic solution given by Bray. The borehole model with a circular opening under biaxial stress was compared with both isotropic and anisotropic solutions resulting in good agreement. The abilities of DEM model to investigate the micromechanisms accounting for complex macroscopic behaviors and to predict the macroscopic behavior are discussed.The results demonstrate that DEM modeling has the potential to be applied to anisotropic rock mechanics problems on larger engineering scales such as wellbore stability problems especially in shale formations. Furthermore, the effect of anisotropy modeled through this study may be able to explain failure behavior of anisotropic rock encountered frequently in real cases.INTRODUCTIONAnisotropy is prevalent in various types of rocks, especially in shale that contain a set of parallel bedding planes. These weak planes in various forms are sources of large deformation and low shear strength and contribute significantly to the anisotropic behavior of rocks (Amadei, 1996; Cho et al., 2012; Kim et al., 2012). As elastic and strength behavior of anisotropic rock is substantially different from that of isotropic rock, proper consideration of anisotropy is of great importance. There is extensive of experimental evidence showing the anisotropy of shale. Niandou et al. (Niandou et al., 1997) analyzed the plastic deformation and failure mechanisms of Tournemire shale were highly dependent on the orientation of bedding planes. Cho et al. (Cho et al., 2012) presented various deformations and strengths of Boryeong shale obtained from laboratory experiments. Fjaer and Nes (Fjaer and Nes, 2013) performed uniaxial and triaxial compressive strength tests using Mancos shale, and they observed that the shear sliding along the planes of weakness before the occurrence of a major failure can reduce the strength of anisotropic rock. The recent research has demonstrated that the anisotropy of rock is an important consideration in rock engineering."

Jan 1, 2015

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. Moreover the texture parameter of the ARB-ed samples was calculated using their XRD patterns and the related equation. Additionally, the texture evolution during the ARB process was demonstrate by analyzing the measured pole figures and orientation distribution functions (ODF) and skeleton lines. The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. Texture analysis revealed fiber textures have been discovered with continiuose of the ARB process cupper. Brass, S and dillamor textures identify which their differences are in intensity of ARB process. Results indicated conformity between mechanical evolutions and texture evolutions during ARB process.

Oct 1, 2011

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. In order to clarify the failure mode, fracture surfaces after tensile tests were observed by scanning electron microscopy (SEM). The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles, lamellar structure elongated in the rolling direction contains lamellar boundaries was formed. With increasing the strain, mean spacing of lamellar boundaries decreased. Finally, continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. The tensile strength and hardness of the 6 cycle ARB processed 5083 aluminum alloy sheet increased about two and three times of the initial values, respectively. Results indicated conformity between mechanical evolutions and microstructural changes during ARB process. Fracture surfaces observations showed that failure mode in ARB processed aluminum is shear ductile rupture with elongated small dimples.

Oct 1, 2011

By T. Tsutsumi, S. Kukino

"During the diametrical compression test, the tensile stress generated near the loading plate is influenced by the contact area between the loading plates and specimen. However, very few studies have determined the contact area. Theoretical or analytical models have shown that for an orthotropic material (i.e., with material properties that differ along each of three mutually orthogonal twofold axes), the maximum tensile stress is generated at the center of disk when the angle of the principal material direction to the loading direction is close to ?/4. The maximum value is almost constant, regardless of the contact area. Conversely, the maximum tensile stress is generated near the loading plate when the angle between the principal material direction and loading direction is small. The maximum value decreases as the contact area increases. Therefore, in the latter case, the influence of the contact area on tensile strength measurement of is significant.In previous studies, the distribution of stresses applied on the loading plate is assumed to be a uniform load. In reality, the applied stress is highest at the center of loading plate and seems to decrease with distance from center. The applied load disappears at the edge of loading plates. In this study, in order to satisfy this boundary condition on the loading plate, the cosine curve is adopted as the distribution of load applied on the loading plates in a theoretical model of the diametrical compression test. Furthermore, the elastic solution using boundary conditions shown in this study is used to obtain the tensile stress distributions on the loading axis for an orthotropic circular plane. These distributions are compared with empirical results obtained under uniform loading with a loading plate or concentrated loading in previous studies."

Jan 1, 2015

By Ken J. Brouwer

Stillwater Mining Company commenced construction and development of the East Boulder underground mine in 1998. This new PGM mine is situated adjacent to the East Boulder River approximately 35 miles south of Big Timber, Montana. Project planning and development incorporated detailed collaboration between the regulatory agencies, concerned citizens and mine personnel. A unique ?good neighbour agreement? was established with a local environmental group who have become actively involved in the review of ongoing site development and the implementation of environmental and compliance monitoring. Environmental management systems allow for integrated management of tailings, waste rock and water in order to minimize surface disturbances and to prevent adverse impacts to the East Boulder River. Long-term site development plans contemplate implementation of comingled waste rock and paste tailings. Water management capabilities allow biological treatment of all excess mine water in order to reduce nitrogen loadings prior to land application disposal by means of spray evaporation, snow making and land application. The comprehensive waste and water management plans have also been integrated with staged mine development and interim reclamation requirements.

May 1, 2002

By Francisco Tamargo

"This paper refers to a new process for the full recovery (above 98%) of zinc and other valuable metals (Pb, Ag, Au) accompanying zinc in its concentrates while iron is separated as a marketable product free of any harmful impurities and suitable for sale to the cement industry. The process has been especially designed to achieve the following goals: maximizing the recovery of zinc and those valuable metals that are present in most zinc concentrates (lead, silver, gold); allowing the recovery of other valuable metals such as indium or germanium that could be present in some zinc concentrates; avoiding or minimizing the need for residue disposal in safe areas as it is the common practice nowadays in the zinc industry. Finally, the process achieves the previously related goals at a competitive cost, in line with the existing more efficient operations while using conventional equipment working under atmospheric conditions. The new process can be easily implemented in those smelters using the jarosite or goethite processes as well as in those smelters using direct leaching as a part of the processing facilities. A study has already been conducted on the use of jarosite in the cement manufacturing process, in the raw mix preparation as well as for a set controller. It shows that use of clean jarosite in the manufacture of ordinary Portland cement can result in improved quality of the clinker. Jarosite showed compatibility to influence the burning characteristics of the cement raw mixes. The presence of SO3 bearing mineral phases such as natrojarosite showed the suitability of clean jarosite for use as a set controller in cement production.INTRODUCTION Iron is by far the most abundant impurity accompanying zinc in its concentrates, and consequently, iron residue disposal is a major environmental concern for many zinc smelters in the world. This is especially true during the last 30 years when environmental restrictions became more and more strict. Much research work has been carried out during the last 30 years to try to find a solution for this important issue, but with little success. Only the jarofix process represents a partial solution to this problem as jarofix is stored nearby the smelters with certain limitations as a non-contaminant residue. However, it does not avoid the need to dispose of an important amount of residues every year, representing an environmental liability. Meanwhile, the number of countries limiting or banning the disposal of iron residues generated by the zinc smelters is growing, so that the solution to this problem is becoming an urgent matter right now. At the same time, the lack of appropriate available land for iron disposal is also a major concern in many cases."

Jan 1, 2016

By A. Fischersworring-Bunk

The new inline six spark-ignition engine is the realization of BMW's concept of efficient dynamics at high technological level to achieve the attributes of low weight and high efficiency, The paper presents different aspects of the development and manufacturing of BMW's inline six-cylinder engine magnesium-aluminium composite crankcase, Reference will be made on the AJ magnesium alloy optimization approach to balance between mechanical properties and the high pressure die cast ability requirements, Next to this aspect some mechanical design issues will be covered, with CAE methods playing an instrumental role in the early project stage for the assessment of the compound concept, Due to the compound design chosen, the interface posed challenges to both design and productions, A set of novel techniques has been used to cope with these tasks.

Jan 1, 2006

By Larry B. Smith

"Feasibility studies are the means by which mineral reserves are established prior to financing a project. However, guidelines are generally lacking for the content, data quality and accuracy of these studies. Regulators take a principle-based rather than prescriptive approach to the content of studies and look to the industry to define study content. Professional organizations, engineering firms and mining companies must eventually establish guidelines and best practices for this work. Most likely these will draw on standards or “stage gates” that have been developed by major mining houses and engineering firms. Engineering studies must: 1.,Define optimal mining and processing methods, production rates, infrastructure, product sales, environmental management and risk mitigation. 2.,Increase confidence in resources, reserves, production plans, processing performance, infrastructure design, environmental management, permitting, capital and operating costs, and financial performance to support financing. 3.,Provide engineering designs suitable for accurate cost estimates. 4.,Develop project execution plans with sufficient confidence that project delays and cost overruns will not occur. Conceptual (scoping, preliminary assessment) Establish the principal characteristics of the project from the geology, resources, metallurgy and development constraints. Assess different approaches to mining and processing. Identify project execution requirements. Test project viability with economic analyses. Recommend additional work to increase the confidence in geology, resources, metallurgical performance, infrastructure, operating and capital costs, environmental conditions and permitting to allow selection of the best development options."

Jan 1, 2003

By N. T. Avard

THE Joggins coal field, Cumberland county, Nova Scotia, is on the easterly side of Chignecto bay, at the head of the bay of Fundy. In area, so far as proven, the field extends easterly from the town of Joggins about fifteen miles to Chignecto. The distance across the outcrops of the several seams exposed is approximately one mile. HISTORY Early records of coal mining in this locality are somewhat obscure, but it is known that prior to 1750 the French settlers were mining coal for their own use from the seams which outcrop in the floor of the bay adjacent to the shore, where, at low tide, the reefs are bared for a mile or more. Coal was also mined from the seams outcropping in the cliffs. It is known, too, that at Joggins coal has been mined commercially for over one hundred years. At first, all shipments were made by water, but in 1882 a railway connecting with the Intercolonial railway at Maccan was built to serve this field. GEOLOGY Due to the abundance of fossils in the strata forming the Joggins cliffs, this area was for many years a mecca for geological students from all over this continent. A 'sunken fcrest' in the shoreline was of particular interest but, due to constant erosion by the sea, this has apparently been all washed away. On the Joggins shore, the cliffs stand sixty to one hundred feet high, and six workable coal seams, with numerous smaller ones, are there exposed. Others outcrop in the reefs extending from the shore toward the bed of the bay. In working underground, fossilized trees are often found immediately overlying a coal seam, and standing at right angles to the pitch of the seam. This is said to be an unusual condition. In most cases, the bark of the tree is a fine-quality coal, with high carbon content, whereas the pulp has turned to 'stone'. There is a definite tendency for the coal to run out, or turn to shale. One seam, workable two miles from the shore, has almost completely disappeared in the outcrop at the shoreline. ? It was thought that a large area could be mined under the bay from an opening near the shore, but the first submarine level had to be abandoned at a distance of 4,000 feet, where the coal became very dirty and shaly, and the mine able area to the westward became more restricted as the mine was developed to the deep. This tendency is common to all seams.

Jan 1, 1944

By Timothy W. Ellis

Gold-based materials have been a mainstay of the electronics and semiconductor industry since the physics was just a laboratory curiosity. Gold is the workhorse material in wire bond, flip chip and off wafer interconnections due to its corrosion resistance, ability to form metallurgical bonds by soldering or cold welding, and ease of fabrication. As the electronics and semiconductor industries grew, so did the use, of Gold in spite of the feature size reduction so elegantly demonstrated in Moore?s law. However, several revolutions in the Silicon miracle are threatening Gold?s place as the material of choice. Although cost is always an issue, the limitations are associated with the chemistry of Gold based alloys. Will Gold remain? Emerging requirements of bioelectronics, photonics and power requirements in conventional device represent new opportunities for Gold to shine. Additionally, as the world market demand for electronic, semiconducting, bio-electronic and photonic technology increases, given the right technology, Gold still can provide value proposition.

Oct 1, 2003

By R. R. Potter

"IntroductionAlthough iron formations were recognized in western New Brunswick about 1820, commercial production was not achieved until 1848. The Jacksonville deposits near Wood stock were developed first, and ore was treated at a blast furnace constructed 5 km to the southeast on the Saint John River. Several charcoal burners were also constructed. Pig iron was produced sporadically until 1884, when operations were finally suspended. There was little further interest in the area until 1953, when Stratmat Ltd. initiated an ambitious exploration program. At the same time, the company carried out research on an electric-reduction process to produce metallic iron and ferromanganese. The technical feasibility of this process (Udy process) was confirmed, however the high energy costs were prohibitive and work ceased in 1957. Some metallurgical research was carried out by Mandate Refining Ltd. about 1970 and more recently by the New Brunswick Research and Productivity Council.The Years Prior to 1848New Brunswick became a separate province in 1784, shortly after the influx of a large number of Loyalists from the United States. Man y of these people sett led along the Saint John River, including the area of excellent farmland near the present town of Woodstock.There were indication s that some of these earl y settlers recognized iron formations in the vicinity of Woodstock about 1820, however the nature of the deposits was not known until 836 when Dr. C.T. Jackson, a geologist commissioned by the Stat e of Maine, investigated the mineral potential of the area. Jackson (1836) described the ""ore"" as compact red hematite yielding 44 per cent pure metallic iron, and suggested that sizable tonnages may be present. It was about this time that an extensive limonite deposit was found in north-central Maine, near Mt. Katahdin. Other iron deposits were found in the Nictaux area of Nova Scotia, and a few years later at Londonderry."

Jan 1, 1983