Search Documents

By I. Orford, V. Rozon

"The Sä Dena Hes Joint Venture Mill was designed to process 450,000 tonnes per year of ore grading 11.3% lead and 13.2% zinc.Run of mine ore is crushed in a jaw crusher and then ground in a closed circuit SAG mill and ball mill. A standard differential float in conventional flotation cells produces quality lead and zinc concentrates. Dewatering of concentrates is achieved using high rate thickeners, lamella clarifiers and pressure filters. Process water is 100% recycle.Plant design was based on metallurgical test work performed on drill core samples. The plant is operating at better than design specifications.INTRODUCTIONSä Dena Hes Joint Venture was formed in 1989 to develop the Sa Dena Hes lead/zinc sulphide mine, located approximately 45 km north of the Town of Watson Lake, Yukon. The mine is owned by a Joint Venture partnership between the operator, Curragh Inc. (87.5%) and Hillsborough Resources Limited (12.5%).The project was completed in a record ten months, working throughout the severe Yukon winter and through an abnormally wet spring and summer. The first truckloads of concentrate were shipped from the mine on August 1, 1991.The mill currently processes 550,000 tonnes of ore per year grading 6.9% lead and 11.5% zinc. Ore is crushed in a jaw crusher and ground to 60% passing 75 microns in a closed circuit operation of one SAG mill and ball mill. Using conventional flotation cells a 150,000 tonnes of concentrate is produced in a year with lead concentrate grading 78% lead and a zinc concentrate grading 60% zinc at overall recoveries of 89% and 90% respectively.Concentrates dewatering is accomplished using high rate thickeners, clarifiers and pressure filters. The lead concentrate and zinc concentrate contain 5.4% water and 7.8% water respectively. Concentrates are trucked to Skagway, Alaska for subsequent shipping to overseas smelters."

Jan 1, 1993

By P. B. Marchant

"Based on laboratory and pilot scale continuous biooxidation of complex sulphide concentrates, commercial processing design and scaleup considerations are discussed. Capital and operating cost estimates for commercial biohydrometallurgical operations are summarized and potential applications of biotechnology are discussed. Biooxidation as an oxidative pretreatment alternative to enhance precious metals extraction from refractory sulphide concentrates in stirred tank reactors has received considerable attention recently due mainly to advances in the practical applicability of the process. Biooxidation of sulphides is certainly not a new process, however, application and control in large scale hydrometallurgical operations to treat refractory sulphides remains conceptual and the limited data available is restricted to relatively small laboratory and pilot scale operations. It is the intent of this paper to indicate scaleup and plant scale process design considerations for commercial bioleach circuits, based on recent operating experiences with laboratory and pilot scale continuous bioleach systems. An indication of the expected range of applications will be presented parameters for optimization will be discussed."

Jan 1, 1986

By C. Bazin, D. Hodouin, M. Ounpuu

Sensors are now available in mineral processing circuits to monitor pulp flowrate and density, as well as ore characteristics and other process variables. The amount of information provided by these instruments is considerable but in many cases poorly exploited. This paper gives the results of the application of time series analysis techniques to signals generated by the sensors installed on an industrial Pb dezincing flotation circuit in New-Brunswick. Autocorrelation and cross correlation functions appear to be interesting tools for a preliminary circuit analysis, however the calibration of single input single output discrete transfer functions using collected sensors signals leads to conflicting results. For this reason a phenomenological approach, based on the kinetic and transport properties of the flotation process, is also considered. It has several advantages over the empirical transfer function modelling but also limitations in its applicability to industrial processes. A combination of the transfer function and kinetic modelling approches appears to be a promising avenue for better process modelling and control.

Jan 1, 1985

By K. Poorhaydari, B. M. Patchett, D. G. Ivey

In this paper, some applications of carbon extraction replicas, as samples for transmission electron microscopy (TEM), are discussed. Modern high strength microalloyed (HSMA) steels, used as structural or pipeline materials, have very small grains with substructures. Replicas used in TEM can resolve the grain boundaries and can be used for grain size measurements in cases where the small size of the grains pushes the resolution of conventional optical microscopes. The grain size variations obtained from replicas correlated very well with mechanical property variations, indicated by hardness, in the fine-grained heat-affected zone and base metal of some welded HSMA steels. Replicas are also very suitable samples for precipitate examination with analytical TEM. Advantages and limitations of the application of replicas, as well as some corrections for the estimation of the volume fraction of fine precipitates, are discussed.

Jan 1, 2005

By C. Sui, J. E. Nesset, M. Li, J. Y. Kim, S. L. Chryssoulis

"A plant study of zinc rougher flotation at Brunswick Mining was conducted using lime, soda ash and a combination of both as the pH modifiers in order to establish the effects on sphalerite and pyrite kinetics and mineral selectivity. The plant sampling and analysis was augmented by surface analysis using TOF-LIMS, SEM and XPS as well as fundamental precipitation and surface-charge studies in the sphalerite Ca/C03/S04 system.The results revealed the important role of carbonate ions in cleaning the sphalerite surface for effective activation by CuS04 to occur, and the beneficial role of combined soda ash and lime in increasing pyrite and galena depression.1.0 IntroductionThe studies reported in this paper were initiated as part of an investigation into the causes of a particularly pronounced seasonal deterioration in metallurgical performance at the Brunswick Mining concentrator during the summer of 1995. The concentrator treats a complex base metal ore having a typical feed composition of 9.0% Zn, 3.5% Pb, 0.4% Cu and 100g/t Ag at a current throughput of 9,000 TPD, although at the time of the problem in 1995, the average production rate was closer to 10,500 TPD. Zinc, lead, copper and bulk (zinc-lead) concentrates are produced with overall metal recoveries of 86% zinc, 63% lead, 60% copper and 60% silver; results which are typical of the lower recoveries associated with fine-grained, highly complex VMS and SEDEX type deposits. The main economic minerals of interest are an iron-containing (7% Fe) sphalerite, galena and chalcopyrite with the main diluent (about 60% wt) being pyrite.Figure 1 shows a simplified flowsheet of the Brunswick milling circuit while the seasonal decrease in summer metallurgy in 1995 is illustrated in Figure 2. Of significance is the rapid drop in copper and lead recovery in June while there is an apparent delay until late August-September before the zinc deterioration reaches its lowest point. A more typical seasonal effect within the experience of the authors is the reverse of the Brunswick situation, namely an improvement in summer performance thought to be associated with improved differential flotation kinetics during warmer weather leading to better mineral selectivity. The historical Brunswick experience was particularly severe during the summer of 1995 with estimated incremental losses of $10 Million for this period. The potential of the very significant economic benefits to be gained from understanding and hopefully improving the annual drop in performance led to an investigation involving the minesite metallurgical group, the Noranda Technology Centre (NTC) as well as researchers in Professor Jim Finch's group at McGill and the surface analytical services and interpretive skills of AMTEL."

Jan 1, 1998

By Julian V. Simela

Conventional methods of underground surveying use theodolites/total stations and 3D laser scanners to obtain information about the underground environment. Current methods of geo-referencing these instruments to a mine reference system include triangulation, trilateration and resection. However, despite technological advancements, surveying procedures have remained slow, laborious and relatively unchanged during the last half-century. Recent innovations in the robotics community have shown that automated mapping of underground mining tunnels can be undertaken using 2D/3D laser scanners. These techniques have the potential to, in turn, improve upon current underground surveying and mapping methods. Automating surveying and mapping using current surveying tools without changing the setting up procedures or removing current constraints, or even changing the type of equipment used, does not change the status quo. The problem of moving from a static, tripod based surveying and mapping system to an unconstrained mobile surveying and mapping system is the subject of this paper. A current challenge for automated mapping is the ability to automatically geo-reference a mobile mapping system to a mine reference system. For a mobile mapping system that uses a horizontally mounted 2D laser scanner to gather data of the underground environment, the challenge of determining its position and orientation within the mine environment is magnified even more. This paper introduces Mobile Automated Scanner Triangulateration (MAST), a technique under development at Queen?s that is designed to geo-reference a mobile mapping system to a mine reference system for the purposes of underground mine surveying. MAST quickly and automatically determines scanner 2D position and orientation (azimuth) in a mine reference frame by using minimal human input.

Aug 1, 2013

By M. Xiao Bo

In recent years, there has been a heightened interest in the hydrometallurgical processing of sulfide ores and concentrates (especially copper sulfide ores and concentrates) mostly in the USA and Chile. Currently, hydrometallurgical operations account for about 30% of the primary copper production. In the present research, the leaching phenomena of IOCG (iron-oxide hosted copper-gold) ores and concentrates were studied. The IOCG ore, which is characterized as having a predominant amount of magnetite with fine chalcopyrite, is currently the center of attention for new copper resources. Heap leaching of IOCG ore is desirable because of its low cost. However, the leaching characteristics of the ores and concentrates and the mechanisms of copper leaching require investigation. This study defines the factors, which affect the leaching operation, such as the ORP, pH and oxidizing agents. Based on these results, the optimal leaching conditions are provided for pilot column leaching test and ultimately, commercial operations.

Jan 1, 2007

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, L. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite by an acid pressure leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project.

Jan 1, 2004

By C. G. Anderson

Alkaline sulfide leaching technology (i.e. ASL) has been studied, presented and published throughout the literature and utilized in some current engineering studies. Yet, the actual industrial applications are very few and the knowledge about these is very limited. Hence, a large gap between the laboratory, publications, engineering studies, and the actual industrial plant exists. Recent studies of ASL applied to copper enargite concentrates definitively bear out this dichotomy. Hence, this paper will seek to dispel the common misperceptions that continue to surround the selective industrial ASL hydrometallurgical technology. For edification of the reader, a listing of ten common misconceptions and myths is listed. As well, ASL history, fundamental aspects and a new flowsheet application for simultaneous gold and high purity antimony oxide production from low grade materials is included. The associated estimated economic considerations are also included to heighten enlightenment about the application of this industrially proven technology.

Jan 1, 2014

By Z. D. Hora

Brick shales and refractory clays are mined at Sumas Mountain near Abbotsford. Sholes and stoneware clays elsewhere in the province have not been developed. THE SUMAS MOUNTAIN deposit near Abbotsford, 80 km east of Vancouver, has been in continuous production since 1905. The deposit is exposed in a small outlier and comprises a sequence of alternating beds of clay and sand. Beds are of Eocene age. Within the 400 m thick ness of sediments are seven distinctive conglomerate members, some up to 20 m thick, interbedded with fine grained sediments including claystones and siltstone , or "shales". Shale is quarried to produce a variety of bricks, sewer pipes and similar products; it is also used for cement. Several different shale beds have been mined over the years and exhibit a variety of fired colours ranging from buff-pink grey to deep red; pyrometric cone equivalents (PCE) range from 3 to 20. A layer of fireclay 3 to 4 m thick that occurs at the base of the sequence has pinkish white to light buff fired colour and PCE of 30 to 33. It is used as a 266 primary component to produce refractory bricks. The shale is quarried and processed by Clayburn Industries Limited of Abbotsford. Another similar but smaller outlier of the same geological formation is known from Blue Mountain, about 20 km northwest of Mission. Other ceramic clays in British Columbia are reported from Quesnel (7 m bed of white stoneware clay, PCE 17 to 19), Giscome Rapids (25 km north of Prince George, 10 m bed of stoneware clay to PCE 31) and anaimo-Comox area (buff to red firing "shales", PCE 8 to 10-1 12) . From 1959 to 1974 Cretaceous shale from Saturna Island in the Strait of Georgia was used to produce lightweight aggregate. Similar deposits of expanding shale are known from the vicinity of Duncan on Vancouver Island.

Jan 1, 1984

By Guichao Wang, Geoffrey M. Evans, Graeme J. Jameson

"In this paper we present a new method for studying the detachment of particles from bubbles in a rotating turbulent eddy. The eddy is formed in a wall cavity in a two-dimensional water tunnel with transparent walls. When water flows through the tunnel, a vortical flow field develops in the cavity. The properties of the eddy can be modulated by changing the free-stream velocity of the water in the tunnel. Bubbles are pre-loaded with one or more particles in a fluidized bed flotation device located beneath the vortex cavity. Loaded bubbles are released one at a time into the cavity, and the motion of the bubbleparticle aggregate is studied using a high-speed video camera. The diameters of the particles and the bubbles, and the number of particles initially attached to the bubble, can be varied. The trajectories taken by the bubbles are quite complicated. In some cases, the bubble moves to the centre of the eddy, and particles rotate around its axis. If the rotational speed is sufficient, particles may detach due to centrifugal force. However, other modes were observed, including inertial detachment due to rapid changes in direction of the surface of the bubble, because of changes in trajectory of the bubble as a whole, or because of pulsations and oscillations of the bubble surface. Clusters of bubbles held together by particles were seen to form and reform. In the traditional explanation for the detachment of particles in flotation cells, it is assumed that particles detach from bubbles rotating in an eddy due to centrifugal force (Schulze, 1977). Although the conditions assumed in Schulze's theory may exist, it is only one of a range of phenomena that can lead to the detachment of particles from bubbles in a turbulent vortex.INTRODUCTIONThe recovery of particles by flotation methods is dependent on the particle size. The recovery in the existing flotation machines reaches a peak for particle size, typically in the range of 20 to 100 µm. This size range varies as a function of the particle’s properties (type and composites). For coarser particles, the recovery drops very quickly (Gaudin, Groh & Henderson, 1931; Jowett, 1980). If the upper size limit can be increased for flotation, dramatic savings in the grinding energy can be achieved."

Jan 1, 2016

Why innovate? ? How are we doing in Canada? ? How can we do better? ? Why now? ? What?s next? ? Lowering production costs ? Improving productivity ? Increasing value-added ? Discovering new mines, extending life of existing ore bodies ? Reducing environmental footprint ? Improving health and safety

May 1, 2008

By A. Perucho, J. P. Harrison, A. Bedi, L. Alejano, L. Lamas, A. Sofianos, A. M. Ferrero, R. Migliazza, R. Olsson, J-F. Mathier

"In 2010, the Eurocode for Geotechnical Design, EN-1997-1:2004 (CEN, 2004), informally known as Eurocode 7 or EC7, became the Reference Design Code (RDC) for geotechnical design – including rock engineering design – within the European Union (EU). EC7 is one standard within the comprehensive Structural Eurocode suite, which as a whole has been also adopted by a number of other countries beyond the EU. EC7 is thus becoming a key design standard for geotechnical engineering worldwide.As part of the Structural Eurocode suite, EC7 requires designs to adhere to the principles of Limit State Design. However, it is not clear that current rock engineering design practice can satisfy this requirement. In addition, evidence is accumulating that EC7 is currently difficult to apply to, and may even be inappropriate for, rock engineering design. These issues may be due to the fact that the development of EC7 to date took place without any formal input from the international rock mechanics and rock engineering community.In early 2011 under the auspices of CEN (Comité Européen de Normalisation / European Committee for Standardisation), EC7 entered a formal period of maintenance which was aimed at improving the applicability and ease-of-use of the Code. This maintenance cycle will conclude in 2020 with the publication of a revised version of EC7.This paper describes a number of critical aspects for rock engineering in the context of EC7, inparticular the following:– the history of the Structural Eurocodes and the concepts they embody;– the nature of Limit State Design and the challenges and opportunities it poses for rock engineering design;– the formal means by which the Structural Eurocode maintenance cycle proceeds;– the plans currently being developed for improving EC7 with regard to rock engineering design and construction;– the unique and vital opportunity for the entire international rock mechanics and rock engineering community to comment on the Code and make suggestions for its improvement."

Jan 1, 2015

By A. A. Shirzadi, E. R. Wallach

"Liquid gallium has been used successfully to modify/remove the surface oxides prior to diffusion bonding similar and dissimilar nickel-base superalloys. Using this approach, bonds in nickel-base superalloys with ""virtually invisible interfaces"" were produced, and the compositions in the bond region were very close to those of the bulk alloys. Room temperature tensile and bend tests showed no preferentially failure at the bond lines. Creep tests on samples made between two different Inconel alloys also showed failure away from the joint, i.e. in the parent metal of the Inconel alloy with lower creep resistance. The high temperature lifetimes of these samples were as long as those of the unbounded Inconel, confirming that the joining approach has no adverse effect on the nickel-base superalloys being joined."

Jan 1, 2006

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By L. M. Cumming

"The contact between dolomite of the St. George formation (Cambro-Ordovician) and limestone of the overlying Table Head formation (Middle Ordovician) is a regional disconformity. This is best illustrated from exposures on Pointe Riche Peninsula, near Table Point, and along Port au Port Bay. The contact occurs along 180 miles of the west coast of Newfoundland from St. John Island in the north to the western part of Port au Port Peninsula in the south. A disconformity of the same age occurs between the Romaine and Mingan formations on the north side of the Gulf of St. Lawrence.Dolomitic beds beneath the disconformity locally contain concentrations of base-metal sulphides. Sphalerite occurs in dolomite pseudobreccias of the St. George formation at Zinc Lake, 7 miles northeast of Daniels Harbour. The 'Western Newfoundland Lower-Middle Ordovician regional disconformity is interpreted as having originated on and near the edge of a broad platform, and to have provided an important regional geological control in the localization of zinc mineralization."

Jan 1, 1968

By Jean-Pierre Birat, François Hanrot, Gérard Danloy

Global warming presents an enormous challenge to the steel industry, which is both carbon-intensive and energy efficient. Lean production can provide some short-term emission mitigation, at the level of the Kyoto requirements. In the middle term, more use of scrap will also help alleviate emissions. But to reach much larger reductions in GHG emissions, on a par with the likely targets that will be set after the Kyoto period, the steel industry will have to imagine new production paradigms, which constitutes its most formidable challenge for the years to come. Carbon capture and sequestration, processes leaner in carbon use, electricity and hydrogen from green sources will have to be added together in a patchwork of process routes, which will have to be developed at great risk in the next decade, hopefully through broad international cooperation.

Jan 1, 2004

By David G. Dixon, Ahmad Ghahremaninezhad, Edouard Asselin

"Atmospheric leaching of chalcopyrite in sulfuric acid solutions is a slow process due to the mineral’s passivation. We have investigated the nature of the passive film in this work. Electrochemical reduction and oxidation of chalcopyrite over the potential range of -0.5 to 1.2 VSHE were investigated in 0.5 M sulfuric acid solution (pH 0.3) at 25 ºC by multicyclic voltammetry and open circuit potential measurement. The influence of scan limits on the evolution of current peaks was studied with both stationary and rotating electrodes. It was observed that the anodic oxidation of chalcopyrite begins at potentials above 0.6 VSHE, most likely by preferential dissolution of iron atoms over copper atoms. The selective electro-dissolution process results in formation of a metal-deficient sulfide passive film (i.e. Cu1- xFe1-yS2, y > x). The passive film dissolves at 0.9 VSHE. Elemental sulfur is one of the products of chalcopyrite dissolution above 1.0 VSHE. Cathodic reactions within the potential region of 0.1 to 0.6 VSHE and anodic reactions at potentials lower that 0.5 VSHE are associated with at least one soluble species from solution. The soluble species involved in the cathodic reactions are likely ferric and cupric, while the soluble species involved in the anodic reactions is likely H2Saq."

Jan 1, 2014

By Chen Bang, Xia Xiao’ou, Zhang Feng

"Ores with compressive strength lower than 150 MPa are usually easy to be crushed by conventional jaw crushers and cone crushers. However, for hard ores with compressive strength exceeding 150 MPa and 200 MPa and even up to 250 MPa, such as andesite, hard basalt and olivine, it is difficult to reach satisfactory crushing size and yield or difficult to meet service life and stability use requirements of quick-wear parts by using conventional crushers. As continued increase in ore mining depth and constant generation of new type materials, equipment demand for crushing hard ores becomes increasing high. A new type inertia vibrating crusher is designed. It is powered by a high-speed rotating vibration exciter and can obtain required crushing force by adjusting eccentric mass, eccentricity and rotating speed so as to crush various ores with high hardness. This paper introduces the design process of its structure and working principle, discusses the design calculation methods of vibration excitation system, vibration damping and energy storage system and other key mechanism and provides technical references for this type of vibrating crusher.DESIGN PHILOSOPHYThe conventional jaw crusher mainly acquires extrusion force from crank motion to realize crushing. The motor drives the eccentric shaft via the transmission device to bring the moving jaw to swing relative to the stationary jaw. When the moving jaw moves close to the stationary jaw, ores between them are crushed by extrusion; when the moving jaw moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving jaw and the stationary jaw.The conventional spring cone crusher and the hydraulic cone crusher mainly acquire extrusion force from cranking motion to realize crushing. The motor drives the eccentric sleeve via the transmission device, the moving cone shaft generates an eccentric distance to make cranking motion under the action of the eccentric sleeve. When the moving cone moves close to the stationary cone, ores between them are crushed by extrusion. When the moving cone moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving cone and the stationary cone under the action of dead weight."

Jan 1, 2016

By N. Chow, W. McCombe, G. Remple, J. Nikkari, L. Nightingale-Mercer

Orano Canada Inc. (Orano) operates the McClean Lake mill in northern Saskatchewan, processing high concentration uranium ore, delivered in slurry form, from the Cameco operated Cigar Lake mine. This slurry is ultimately processed into the purified uranium oxide product known as calcined yellowcake. During the calcining process, sulphate (SO42-) entrained in the yellowcake undergoes thermal decomposition into sulphur dioxide (SO2). SO2 is a colourless gas that poses health and safety risks. Since 2016, an anhydrous ammonia dosing system was successfully added to the existing Venturi particulate scrubber system to provide efficient removal of SO2 from the calciner off-gas. Within the pH controlled scrubber solution, SO2 exists in a pH dependent equilibrium with sulphite/bisulphite (SO32-/ HSO3-). The presence of a significant fraction of reduced sulphite and bisulphite in mill solutions presents a hazard in downstream circuits. Should these solutions drop in pH, either through natural oxidation or inadvertent mixing with low pH solutions, the solution equilibrium will shift from SO32-/HSO3- in favour of SO2, resulting in the evolution of SO2 gas from any liquid surfaces. In 2018, Hatch Ltd. (Hatch) and Orano implemented a design change in the calciner scrubber system. Blowdown from this system is now treated in an oxidation pre-step utilizing hydrogen peroxide (H2O2) and anhydrous ammonia (NH3) for pH control, in order to convert the residual sulphite/bisulphite present in solution to stable ammonium sulphate product. This paper will detail some of the challenges and actions undertaken to minimize SO2 risk, culminating in the recent introduction of a novel system designed to oxidize sulphite/bisulphite and prevent mobilization from the calciner scrubber solution into other mill areas where there is the potential for acidification and SO2 release.

Jan 1, 2020