Search Documents

By N. Shi, T. G. Joseph

ABSTRACT A revised equilibrium approach to evaluate dipper-ground interactions during the dig cycle of ultra-class mining shovels operating in soft unblasted uniform ground conditions is presented. A review of previous approaches, leading to an outline of the modifications and ground condition considerations, is made in support of the reasoning and basis for the derivation presented. An analytical solution is provided to the scenario of a cable shovel dipper digging in soft ground material such as oil sands.

Jan 1, 2012

By L. A. Anestiev

A method based on use of calorimetric data for the determination of solidification kinetic parameters is proposed. The method incorporates recent theories of nucleation and growth and allows modeling heat fluxes observed in calorimetric experiment. Statistically optimal estimations of the kinetic parameters, which include the activation's energies of nucleation and growth, are derived from experimental data by means of nonlinear regression analysis. The method is applicable to pure substances and alloys. The evaluation of the kinetic parameters characterizing solidification of pure Al is used for clarifying and exemplifying the method.

Jan 1, 2004

By M. J. Nicol

The leaching of gold with thiosulfate solutions in the absence of ammonia and copper ions was investigated using electrochemical and kinetic methods. In sodium thiosulfate solutions, the electrochemical oxidation of gold was hindered and the leaching rate using pure oxygen as the oxidant was very slow. It was found that the addition of a small amount of thiourea or formamidine disulfide to the thiosulfate solution greatly enhanced the oxidation of gold. However, the enhancement to the overall dissolution of gold using dissolved oxygen as the oxidant was limited. This was attributed to the fact that the oxygen reduction process was unaffected by the additives and remained slow, which limited further improvement to the overall kinetics. An alternative oxidant, the ferric EDTA complex having a reduction potential of approximately 0.12 V, was found to be promising. The cathodic reduction of ferric EDTA was fast and reversible at neutral pH. While the ferric EDTA complex was effective in oxidizing gold, it did not appear to significantly oxidize thiosulfate. A thiosulfate solution containing thiourea and ferric EDTA has been shown to quickly dissolve gold in the form of a powder as well as from gold ores. In the leaching with the ores high gold recoveries of above 90% was achieved with the best performance obtained in neutral solutions (pH 6-7).

Jan 1, 2005

By D. McConchie

The use of Bauxsol? (physically and chemically modified alumina refinery residues) to treat acid rock drainage (ARD), and sulphidic waste rock and tailings, provides new options for managing some intractable environmental problems at both derelict and active mine sites. Treatment of ARD waters using the Bauxsol technology shows that the effectiveness of raw Bauxsol material can be enhanced by including modest amounts of selected industrial minerals or common chemical additives. The type and amount of additive required and the amount of the blend needed to treat the water depends on the initial composition of the water and the target water quality; for some ARD waters, optimum treatment may require one or more changes in the type or amount of additive used. Maximum treatment efficiency can be achieved only when a balance is maintained between the rate of trace metal binding and the rate of change in water pH; adding treatment reagents faster than can be accommodated by the reaction kinetics will not result in more rapid water treatment. This paper presents the results for treating several ARD waters to illustrate the importance of blend selection and treatment procedure. Although treating ARD water is often necessary, this strategy treats the symptoms rather than the cause. The best permanent solution is to treat the sulphidic waste rock or tailings such that they do not continue to oxidise and produce acidic metal-rich leachates; sulphide oxidation needs to be stopped or slowed to a rate that can be accommodated by normal environmental processes. Capping lined impoundments is not a solution because all caps and linings will inevitably fail some time in the future creating a nasty surprise for some future generation. Adding lime is also less than ideal because the lime leaches from the treated material; treatment often appears to be effective for a few years and then fails. Bauxsol technology offers effective alternatives to conventional liming and capping procedures and Bauxsol blend application rates and procedures can be planned to ensure that no acidic or metal-rich water can ever escape from the site. Bauxsol can be physically mixed with the sulphidic mine wastes or it can used to form subsurface permeable reactive barriers, or both. Bauxsol treated waste rock and tailings can be immediately and effectively revegetated. In this paper we present leachate quality and plant growth rate data for several sulphidic waste rock and tailings deposits treated using the new technology.

May 1, 2003

By Andrew D. Lapworth

The use of geological and grade models has been standard practice in mine design for many years now, with a wide range of software available to create and analyze the models. Although geotechnical parameters are also of vital importance for mine planning, there has been very little in the way of commercially available systems for integrating geotechnical data into the mine planning and design process. Sirovision is a new technology based on digital photography for automated, safe and accurate 3D mapping of geological and geotechnical features in rock faces. Datamine has integrated this capability into its product range so that Sirovision becomes an integral part of day-to-day face mapping, mine geology and geological / geotechnical modeling in both open pit and underground mines. This results in improved fragmentation for loading, hauling and processing, and for open pits local geotechnical conditions can be taken into account to improve slope design and control. This paper describes some of the ways that geotechnical modeling can be used to create more refined and cost effective mine designs and then discusses the role of Sirovision in enabling the raw data required for such modeling to be collected quickly, safely and reliably.

May 1, 2007

By H. W. Hughes

"The Wasamac Gold Mines mill, situated 10 miles from Rouyn-Noranda on highway 59, commenced milling April 1st 1965 at a rate of 700 tons per day. This has gradually increased to over 1200 tons per day in December. The mill has done up to 1400 tons on occasion.The ore was formed in the Wasa shear zone by means of replacement. The minerals which replaced the original rocks were carbonates, quartz, pyrite, chlorite, gold and silver. Work index varies from 9. 6 on the chlorite to 11. 6 on the quartz. The gold is very finely disseminated throughout the gangue and while associated with the pyrite is not included in the pyrite. Very seldom is gold found or seen in the free state.Test work showed a medium fine grind of 85 to 90 per cent was necessary to achieve a 95.00 per cent extraction. Straight cyanidation time of 30 to 36 hours was indicated. This has been borne out by subsequent mill performance with a grind around 87 per cent minus 200 mesh and extraction ranging from 95 to 96 per cent.When it was decided to bring the Wasamac property into production, the Bicroft Uranium Mines Ltd. crushing and grinding units together with one pebble mill and the pachuca tanks from Dyno Uranium Mines Ltd. were purchased.Wasamac crusher house and mill buildings are of laminated wood construction, covered with 5/ 8th inch plywood and corrugated iron sheeting."

Jan 1, 1966

By M-A. Thibault, C. Gauthierand, J-P. Gagné, J-Y. Carrier, P. Rochette, G. Dufour

"Anodes consumed in the electrolytic process for the production of primary aluminium are considered consumables. They need to be replaced at regular intervals of approximately one month. The so-called anode butts which are removed from the cells contain the metal supports (rods), cast iron thimbles, crust and residual carbon material. Cleaning is required to remove the waste material before the rods are fitted with new anodes. An inspection is required to ascertain if repairs to the rods are necessary. Presently, this inspection is carried out visually. ST AS, in 2004 in collaboration with Alcoa Deschambault, initiated a project to develop an automated inspection system. The objectives were to find a technical solution to perform these functions with a very simple system. Such a system was designed around ""artificial vision"". The inspection system developed uses only one fixed camera and does not require a separate step in the process for the anode rod assembly to perform the inspection. This paper presents the initial steps of the work performed to develop the equipment and software as well as a summary of the results obtained."

Jan 1, 2006

"In 2000 the CIM Council approved the CIM Standards on Mineral Resources and Reserves – Definitions and Guidelines, developed by the CIM Standing Committee on Reserve Definitions. The Definition Standards established definitions and guidelines for the reporting of exploration information, mineral resources and mineral reserves in Canada. The Mineral Resource and Mineral Reserve definitions are incorporated, by reference, in National Instrument 43-101, Standards of Disclosure for Mineral Projects, which came into force in Canada in February 2001 and was amended in December 2005.CIM DEFINITION STANDARDS- For Mineral Resources and Mineral ReservesPrepared by the CIM Standing Committee on Reserve DefinitionsAdopted by CIM Council on December 11, 2005FOREWORDCIM Council, on August 20, 2000, approved the ""CIM Standards on Mineral Resources andReserves - Definitions and Guidelines,"" developed by the CIM Standing Committee on ReserveDefinitions. The CIM Definition Standards on Mineral Resources and Reserves (CIM DefinitionStandards) establish definitions and guidelines for the reporting of exploration information,mineral resources and mineral reserves in Canada. The Mineral Resource and Mineral Reservedefinitions were incorporated, by reference, in National Instrument 43-101 - Standards ofDisclosure for Mineral Projects (NI 43-101), which became effective February 1, 2001.At the August 20, 2000 Council meeting a new CIM Standing Committee on ReserveDefinitions was established consisting of the following: John Postle, Bernie Haystead, LarryCochrane, Normand Champigny, Mike Hoffman, Colin McKenny, Jack Mullins, Phil Olson,Fred Payne, Jody Todd and Joe Ringwald.Subsequent to the publishing of the August 20, 2000 CIM Standards on Mineral Resourcesand Reserves, various CIM committees have compiled and published more extensivedocumentation on mining industry standard practices for estimating Mineral Resources andMineral Reserves. These standard practices provide more detailed guidance than that containedin the August 20, 2000 CIM Standards on Mineral Resources and Reserves. On November 14,2004 CIM Council adopted an update to the CIM Definition Standards to reflect the moredetailed guidance available and effect certain editorial changes required to maintain consistencywith current regulations. This version of the CIM Definition Standards includes further editorialchanges required to maintain compatibility with the new version of National Instrument 43-101which is expected to become law at the end of 2005. The CIM Definition Standards can beviewed on the CIM website at www.cim.org."

Jan 1, 2003

By Robert J. McCarthy

Mining has a record of achievement in developing and adopting new technology to facilitate the extraction of increasingly challenging resources. Certainly larger, or more capable, mining equipment has allowed mining companies to mine mineral deposits at lower unit costs; however, there has also been the advent of computerized systems that aid in the management and tracking of mining operations. Unfortunately, the latter computerized systems have not always had the success anticipated with their implementation. This paper explores the view that increased transparency of the planning and operating cycle in a mine, as provided by certain computerized systems, can result in some resistance from those whose work becomes ?exposed?. Examples are drawn from industry-leading technologies for both mine management and reconciliation that illustrate the issues and challenges that result. The adoption of appropriate change management principles is suggested as a best practice in planning and mitigating the challenges in implementing technologies which increase transparency in the mining environment.

May 1, 2011

By Mihaita Matei

An adaptive approach to control the deformation in tube hydroforming process is presented. This requires: the use of an existing non-linear FE software (ABAQUS) that incorporates a user material model (VUMAT), the development and implementation of an adaptive control strategy to coordinate the internal pressure and the axial load so as to prevent fracture and wrinkling failures (knowledge-base controller) and the application of the developed adaptive simulation approach for finding the optimal loading path required to hydroform a defect-free part with as uniform thickness distribution as possible (user's load subroutine (VDLOAD). In order to validate the approach, the case of conical hydroforming and the case of bending followed by hydroforming component is discussed.

Jan 1, 2011

By T. G. Sitharam, Resmi Sebastian

"Wave propagation studies across jointed rocks have significance in the fields of rock mechanics and geophysics. The passage of a seismic wave induces strains in rocks and often, these strains are of low magnitudes except at the vicinity of source. These low magnitude strains are generally in the elastic range and hence elastic constants necessary for the design and analysis of strength of rock mass, can be derived from wave velocities. Measurement of travel time velocities and measurement of resonance frequencies are the two methods usually adopted for obtaining wave propagation velocities.Resonant column apparatus measures wave velocities from the resonant frequencies obtained during testing. Depending on the type vibration applied, torsional or flexural, shear and compression wave velocities are secured. By varying the amplitude of vibrations applied, various strain levels can be introduced and corresponding resonant frequencies and wave velocities can be calculated. The resonant column experiments were performed on a model material, hardened Plaster of Paris (POP) samples, in laboratory. The paper explains the preparation of samples and the working mechanism of resonant column apparatus along with the estimation of wave velocity from resonant frequency. The numerical simulation of resonant column apparatus using distinct element method and its validation with the experimental results are presented in the paper.A distinct element code is usually used to simulate the movement of materials with intersecting discontinuities. Finite rotations and displacements of individual blocks representing the material are permitted and new contacts between the blocks are identified as the calculation progresses. Three dimensional Distinct Element Code (3DEC), the software intended for the numerical simulation of rock engineering projects, can well simulate the behavior of jointed rocks under static and dynamic loading conditions. The numerical simulation of resonant column apparatus has been performed with 3DEC considering its efficiency in modeling jointed rocks.The numerical modeling of the resonant column apparatus with application of torsional and flexural vibrations to the sample is elaborated in the paper. The response of samples to a range of frequencies is obtained and the frequency that induces maximum displacement in the sample is measured as the resonant frequency, for any particular strain level. The displacements measured at various points of the sample during application of vibrations are compared and presented. The numerical modeling of resonant column apparatus with an intact sample (without joint) and a sample with a joint incorporated are explained at a particular strain level. The resonant frequencies obtained from laboratory experiments and numerical simulations are compared and illustrated. It has been found that resonant frequencies obtained using numerical and laboratory experiments are in good comparison and can be extended for various strain levels and sample conditions."

Jan 1, 2015

By K. John

"THE most recent estimate of minteable coal reserves in Saskatchewan was made by the Federal Royal Commission on Coal (1944- 6). Saskatchewan was then estimated to have some 24 per cent of the Canadian reserves and two-thirds of this is located in what is called the Souris-Estevan area, which lies in the southeast corner of the Province and border's on the International boundary. It is also estimated that there are some 61/2 million thousand-tons in this area of lignite coal which grades 8,000 B.t.u. or less and has a moisture content ranging from 30 to 33 per cent. Ownership of coal rights in the Province is widely dispersed between the Crown, individuals, and corporations, and a recent survey disclosed that 40 percent of ownership was vested in the Crown and 60 per cent in private individuals and corporations. Coal rights on Crown lands may be leased at an annual rental of $ 1.00 an acre. Under such leases, a royalty of 5 cents a ton is levied on all coal mined. A royalty of 7 cents a ton is levied on coal produced from lands where mineral rights were purchased from the Federal Government prior to the transfer of jurisdiction over natural resources to the Province, in 1931. An annual mineral tax of 50 cents per acre has also been imposed by the Provincial Government on all coals within a defined producing areas."

Jan 1, 1952

By Shigeru Sarata

A wheel loader is one of the main loading machines in open pit mines. The authors have been conducting research and development on autonomous operation of loading by a wheel loader. The most common loading method by a wheel loader is the ?V shape? path method. The loading operation consists of cycles of scooping from the pile, traveling to the dump truck, loading on the dump truck and return traveling to the scooping point for the next cycle. The traveling path includes a switchback in the middle of the path. The moving direction of the loader is changed at the switchback point. From observation of V shape path loading operations by experienced human operators, it seems that they control the bucket position between the scooping point and loading point on a shorter path for higher productivity. A new path planning method is proposed this paper, whereby a point on the center of the tip of the bucket is controlled moving from the initial point and the final point. The motion of the controlled point is generated by the wheel steering the wheel loader. The controlled point is moved along the direction to the final point; however, the motion and mechanism of wheel loader have restrictions, such as the velocity of the loader, the steering angle, and the steering angular velocity. Because of these restrictions, the path of the controlled point is not a straight line between the initial and final points. When this control method is applied between the scooping and the dumping points directly, the planned path is not stable in the leaving wing of V shape path. Therefore, the initial position of the wheel loader is set at the switchback point, then two approach wings to the scooping and the dumping points are made. The whole planned path is obtained by connecting the two paths. The shape of the planned path is strongly affected by the position of the switchback point, as well as the scooping and the dumping points. By simulation of path planning at different switchback points with the combination of the scooping and the dumping points, the paths for more effective loading are determined. The results of the simulation are presented in the paper.

Aug 1, 2013

By E. G. Joe

"Recent trends in Canadian mineral processing were reported in seven areas of interest covered by seventeen technical papers at the 1976 Annual Meeting of the Canadian Mineral Processors, held at Energy, Mines and Resources' Camsell Hall, Ottawa. New milling equipment included the Enviro-Clear thickener, large-volume Outokumpu flotation machines and abrasion-resistant polyurethane screens. Grinding experiences from a variety of milling operations were reported. Opportunities for increased sizing and grinding efficiency were presented. Flotation control by digital computer and by chemical additions were described in two mill operations. Slurry pumping and sampling techniques were described for various operations. Environmental control in milling was reported concerning dust suppression, arsenic removal and tailings disposal. Several aspects of gold milling were described by the most recently commissioned gold mine and by CANMET. Potash operations were reported showing the similarity of processing and process control to that of metallic minerals."

Jan 1, 1976

By A. Bouajila1

Minerals processing organisations will be more and more under intense competitive pressure. Major changes are being experienced with intense respect to resources, processes, production strategies and markets. As result of international competition, only the most productive and cost-effective operations will survive. That is why operators in the minerals industry have always aimed to obtain better performance from their processes along the mineral extraction cycle starting from exploration up to the smelting step if any. A principal ingredient and perhaps the most important one in the process of evolution toward improved productivity is the achievement and implementation of an error-free production synonym of an ignorance-free operation. This is, at the same time, a guarantee for quality, a minimising factor for waste materials production, handling and disposal, and a maximising factor for labour utilisation. The notion of ?error or ignorance-free? -usually identified as a ?made in Japan? manufacturing mythology, will sound, at first impression, like a pious ideal, to be striven for but impossible to attain. Nevertheless, the introduction of measurement and detection technology in the minerals industry along the last century should benefit from the today?s sensors and control systems that explosively expanded beyond their traditional production base into far-ranging commercial ventures. The fastness and spread of those technologies will play an important role in the survival of innovative plants. Their role in information assimilation, and control of operations to maintain an error-free production environment, will help many plants to stay effective on their competitive course. In this paper the feasibility of the zero process ignorance concept as applied to the comminution circuits will be discussed and the challenge behind this ambitious move toward improved productivity will be outlined. Examples of pre-competitive R&D projects started at COREM in order to fulfil this prerogative will be presented.

May 1, 2001

By W. Dolsak

Introduction Alternative bolting injection resin Hollow bars, rebars, and cable bolts Results from an in-house product development project Sept. 2011 to Feb. 2013 Goals Introduction of a newly developed bolting silicate injection resin as alternative to cement grout based injection systems Definition of easy-to-use pumping devices and installation accessories Accomplishment of installation trials and performance evaluation

May 1, 2013

By W. J. Stickney

"Over-all recovery of cadmium has been increased at the plants of the Hudson Bay Mining and Smelting Co., Limited, since the construction of a slag fuming plant and baghouse where smelter flue dust is recovered. This pa-per outlines the distribution of the cadmium in plant products from the concentrator to the refining department.The leaching of cadmium-bearing precipitates from the zinc plant is also discussed. This consists of a two-stage leach; first with sulphuric acid and then with copper sulphate. Details of the leaches are outlined along with the safety measures practised in handling the hydrogen and arsine evolved.The paper describes the final preparation of electrolyte for the refining cells by purification for copper and thallium. Deposition of cadmium, using a polyacrylamide as an addition agent, is discussed.An outline is given of the melting procedures, under either sodium hydroxide or zinc chloride, and of the sub-sequent treatment of the dross to recover entrained cadmium and thallium."

Jan 1, 1966

By Richard W. Herzer

Introduction Thermal methods have been predominant in the metallurgy of the base-metals ever since the foundation of the industry thousands of years ago. Development in hydrometallurgy has been confined largely to the past six or seven decades. It was at first necessarily slow, then for a number of years rapid progress was made. At present, the uncertain state of the metal industry has curtailed research on the subject; however, in the next few years one may assuredly look forward to an ever increasing use of wet processes. Leaching methods have attained the dominant position in the case of certain metals, notably zinc. For others, they have made no headway at all. Copper presents a situation all its own. Due to the varied nature of its ores and to the large number of localities in which it is mined, a great number of processes have been developed, each suitable in its own particular field. In the case of this metal, therefore, it is more difficult to arrive at definite conclusions. It is the purpose of this paper, first, to review the outstanding developments of base-metal hydrometallurgy, and, secondly, to consider possible Canadian applications of some of the processes in use. The discussion will be confined to the three metals, zinc, lead, and copper, with particular reference to the last mentioned. Zinc General Note At present, zinc is produced by two principal processes, the older retort process and the electrolytic process. The latter is a development of the last twenty years and, judging by its present progress, bids fair eventually to supplant older methods in a large proportion of cases. It is certain, at least, that in the erection of a new plant, a hydrometallurgical process would be given the most serious consideration

Jan 1, 1934

By P. Dauphin

"CANMET’s Mining and Mineral Sciences Laboratories have developed the Canadian Mining Technology Network (CMT-Net), a website to provide industry with up to date information on technologies in several areas. This paper gives background on the Mineral and Metal Processing sector, describes the steps leading to the development of the websites strategy and gives a tour of CMT-Net. IntroductionThe government of Canada is developing a strategy aimed at fostering the development of value-added activities in the area of mineral and metal processing (MMP). Natural Resources Canada (NRCan) and Industry Canada will partner in delivering on this strategy. Instrumental in defining the main thrusts of the value-added strategy was a series of consultations held across Canada with representatives of companies and organizations active in the sector. The objective of the consultations was to identify barriers to the development of activities which add value in the sector, as well as point to positive factors.Following the consultations, a discussion paper was produced, “From Mineral Resources to Manufactured Products: Towards a Value- Added Mineral and Metal Strategy for Canada” (Natural Resources Canada, 1998). The paper reviews the sector’s structure and main statistical information, lists some of the positive factors and barriers to value-added activities and defines a new partnership between industry and government that will lead to more valueadded activities. The main objective of the paper is to serve as a discussion document between stakeholders during the development of the strategy."

Jan 1, 1999

By T. L. Tanton

"The New Helen mine is 12 miles east of Michipicoten harbour on lake Superior. It is 2 miles east of Wawa station, on the Algoma Central railway, with which it is connected by a spur line railway and a highway.The mine was discovered by Ben Boyer in 1898 during the gold rush near Wawa lake, Ontario. The original discovery was of solid hematite ore extending to a height of 100 feet on a hill rising abruptly on the east side of Boyer lake. The property was acquired by the Algoma Steel Corporation and mining was commenced in 1899. The first iron ore was shipped in 1900. The mine was operated until 1918 when the hematite became exhausted at a depth of 800 feet below Boyer Lake level.Drilling at the Helen mine, after 1910, revealed a large body of siderite both below and to the east of the hematite. By 1913, the body was known to be about 200 feet wide, 3,000 feet long, and at least 2,200 feet deep. In this there was estimated to be 100,000,000 tons of proved and probable siderite ore. An adit was driven into this body in 1917, and in 1918 work was suspended. In 1937 the Algoma Steel Corporation proceeded with the development of the New Helen mine by open-cut mining, and the beneficiation of the ore by sintering. Production commenced in 1939 and has since been maintained at the rate of approximately 500,000 tons a year.From 1900 to 1918, inclusive, the total production from the Helen mine was 2,823,369 tons of hematite ore and 51,930 tons of pyrite. From 1939 to the end of 1945 the total production from the New Helen mine was 3,921,455 gross tons of siderite ore.GEOLOGYThe Helen property is underlain by rocks of Precambrian age. For general description, and a statement on the structure of the iron deposits, the map-units are those shown in Fig. 1.The oldest rocks occur in a complex that lies north and south of an east-west trending zone, 1 ½ miles long and ¼ mile wide, in which the iron deposits occur. That part of the complex lying south of the iron deposits includes small masses of altered conglomerate and slate, and greenstones and pyroclastics. Other fairly abundant rocks are sericitic, chloritic, ottrelitic, and carbonatized schists of doubtful origin, and almost massive metamorphic rocks in which a development of carbonate, ottrelite, quartz, and other minerals has obscured a pre-existing schistose structure. Felsite and quartz porphyry are· prominently exposed south of the iron deposits."

Jan 1, 1954