Search Documents

By G. Stokreef, B. R. Davis, M. Kadiyski, Alvear Montenegro, H-P. Loock, V. Montenegro

An optical probe for burner monitoring in copper flash smelting, first developed at the University of Concepcion, is being industrially tested in a collaboration between Kingston Process Metallurgy, Aurubis AG, and Queen’s University. The sensor uses fibre-optics and optical emission spectroscopy to analyze the light emitted from combusting particles in the furnace reaction shaft. Information that can be extracted from the emission spectrum includes the temperature and brightness of the flame, as well as emission lines or bands from excited atomic and/or molecular species. Laboratory proof of concept testing of the sensor was first completed in a continuously fed drop tube reactor using O2/S stoichiometric ratios between 0.8–4.0. These O2/S stoichiometries capture the industrial operating condition, which is typically less than 1. The results from lab testing justified a plant trial of the optical probe, which was done in the Aurubis Hamburg flash furnace in September 2018. From this trial, approximately 31 hours of spectral data were collected and synchronized with furnace operating data. The results from both drop tower test work and the plant trial are discussed with implications for process monitoring in the commercial furnace. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process. It is used to treat copper sulphide concentrates and small amounts of secondary materials, such as dust generated by the process. O2 enriched air and the concentrate blend are fed into the furnace reaction shaft through the concentrate burner. As the particles fall through the reaction shaft, they heat up and ignite, causing rapid, exothermic reactions that oxidize the iron sulphide, some copper sulphide and impurities in the feed. Reacted particles fall into the settler of the furnace, melt and separate into a matte and slag, while the SO2 enriched off-gas is carried out of the furnace for heat recovery and H2SO4 production. Operation of the furnace is achieved by adjusting a limited number of control variables. The main variables are the blast feed rate, blast oxygen enrichment, SiO2 flux feed rate and CH4 combustion rate (CH4 is used when the chemical energy of the concentrate is low) all measured relative to a set feed throughput. (Davenport & Partelpoeg, 1987; Davenport, King, Schlesinger & Biswas, 2002) The batch tapping nature of flash furnaces makes operation difficult because these control variables impact each other, and product quality can only be measured when matte and slag are tapped from the furnace. This means that operation of a furnace is based on feedback control from matte and slag assays. Because of the time-delay associated with understanding product quality, there is interest in using technology to monitor the combustion reactions that happen in the furnace reaction shaft.

Jan 1, 2019

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By Andrea M. Ouchi

A major focus of ground control research presently being conducted by the Geomechanics Group in the University of British Columbia Mining Engineering Department is to incorporate weak rock masses (RMR76 less than 50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented by mapping of one mine in Montana and of several mines within the Carlin and Getchell Trends of Nevada. In addition, a neural network analysis has been performed and modifications of the span design curves at the lower RMR76 range have been made. The common factor in all the above mentioned mines is a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be dealt with to safely extract the mineral bearing rock. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

May 1, 2004

By B. Hart, J. Marois

"Scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM–EDX), and Time of flight secondary ion mass spectroscopy (TOF-SIMS)were used to analyze pyrochlore grains from Niobec froth flotation plant. Samples from the mill feed, pyrochlore rougher feed, pyrochlore rougher concentrate, and tail were analyzed in order to identify a potential relationship between pyrochlore matrix composition and selective separation. SEM-EDX analyses indicate that pyrochlore grains with high Fe content appear to be less recoverable than those with a lower Fe content and that the flotation response is related to matrix Fe rather than Fe occurring as inclusions. TOF-SIMS was used to analyse the surface of high Fe and low Fe pyrochlore, in order to identify a potential relationship between pyrochlore matrix composition and the related effect on cationic collector adsorption (tallow diamine). Surface analyses of pyrochlore from a conditioning test show that species indicative of the collector favour the surface of Fe poor pyrochlore relative to the Fe rich variety. The results from the conditioning test illustrate a negative relationship between collector loading and the presence of Fe and related oxidation species. This study identifies the link between pyrochlore matrix Fe content and, the presence of surface oxidation products, to collector loading. Poor Fe rich pyrochlore recovery noted in the Niobec froth flotation plant may be partially explained by this mechanism.INTRODUCTIONPyrochlore, the most abundant niobium containing mineral (Perrault and Manker, 1981) is economically recovered in Brazil, China, and Canada (Niobec) (Kouptsidis et al., 2008). Since 1974 Niobec has been extracting niobium from the St-Honorécarbonatite deposit. Niobec is the only operating Nb extraction facility in North American and one of the three major world producers of ferroniobium (Dufresne and Goyette, 2004; Belzile, 2009).Flotation is the preferred and most cost-effective method for pyrochlore recovery (Burks, 1958; Shapolov and Polkin, 1958; Zakharov et al., 1967; Razvozzhaev and Nikiforov, 1972; Bogdanov et al., 1973; Abeidu, 1974; Raby and Desrochers, 1975; Wilson, 1979; Biss and Nadeau, 1982; Biss, 1985). With the aim of optimising the flotation process for the Niobec ore, numerous experiments were performed on the influence of surfactants and type of water to optimise pyrochlore recovery and grade during flotation (Gomez et al., 1987; Rao et al., 1988; Dufresne and Goyette, 2004; Belzile, 2009)."

Jan 1, 2013

By G. M. Ritcey, K. E. Haque, S. H. Lucas

"Laboratory-scale hydrochloric acid leach tests were conducted on an Elliot Lake uranium ore. Hydrochloric acid leaches without an oxidant or with molecular oxygen (i.e., air or pure oxygen gas) as an oxidant favoured uranium and radium extractions. Conditions for maximum uranium, thorium and radium extractions with hydrochloric acid in the presence of sodium chlorate were determined. The highest extractions of uranium (96%), thorium (81%) and radium (91%) were obtained using a mixture of 44.0 kg HCI and 2.5 kg NaCIOJ per tonne of ore at 75°C with 18 hours ' retention.Flowsheets for two-stage leaching are proposed. The residues obtained from the second-stage leach contain uranium (0.002%), thorium (0.006%) and radium (15 to 20 pCi/g). Tailings of this nature are considered suitable for mine backfill, and, if pyrite is removed, suitable for surfacedisposal.IntroductionThe nuclear energy industry forecasts an increasing demand for uranium. This increasing demand requires not only largescale mining and processing of conventional and complex uranium ores, but also leads to the consideration of new and nonconventional sources of uranium, e.g., black shales, phosphate rocks, granite, sea water and fossil-fuel ash.Sulphuric acid leaching is the most widely used process to extract uranium from the ore(l). The leach liquor is separated from the solids (tailings), purified, concentrated in various intermediate stages, and finally a semi-purified product, yellow cake (80-85070 U30 8) , is precipitated. The tailings, which constitute nearly 98% of the total bulk of most ores, are usually discarded in surface disposal areas.The Elliot Lake region of Ontario is one of the major uranium producing areas in Canada. The principal uranium minerals are brannerite and uraninite, present as microscopic grains in the matrix of quartz-pebble conglomerates. The average grade is between 0.10 and 0.15% UPs. Up to 6.5% pyrite is also present in the conglomerates. Because pyrite is less reactive toward sulphuric acid leaching, almost all the pyrite goes into the tailings and eventually into' the disposal sites."

Jan 1, 1980

By Gunnar Nord

Introduction ??Atlas Copco has customers both amongst Miners and Contractors ??We believe that the contractor's approach to tunnelling is worthstudying ??For a tunnel contractor the incentive is speed as ?30 % of the costs are material related ?70 % of the cost are time related ?A tunnel contractor favours utilizing of the face ?A miner favours utilizing of the gear ??Statement; In mining, a long term average advance rate of more than 10 m / day can be achieved with the excavation techniques availabletoday

May 1, 2009

By K. Szafran, R. E. L. Seal, M. Tansey

Conversion of hydraulic equipment to fire resistant fluids has been hampered by less than satisfactory component performance and in some cases, catastrophic equipment failure. Concern over identifying possible causes to these problems led to a joint research project between the Potash Corporation of Saskatchewan Mining Limited and the University of Saskatchewan. This paper summarizes some of the results and conclusions derived from this joint project. In this study, the research was limited to evaluating the effects of potash contamination on the performance of hydraulic equipment. Two separate types of tests were conducted in order to provide a basis upon which trends could be established. This study concluded that the presence of potash dust in the hydraulic fluid can induce severe wear over relatively short periods of time. It was also deduced that a contaminant free fluid combined with proper fluid maintenance could extend the performance of hydraulic components using fire resistant fluids even under very severe operating conditions, such as elevated pressures and temperatures. Recommendations as to how to achieve this goal and the practicality of doing so are presented.

Jan 1, 1988

By Alex Doll, Derek Barratt

"There is a number of comminution tests commonly used in the mining industry. Many of the tests are used for a particular grinding model or mill sizing program and are incompatible with other tests of different models. This paper provides an overview of the commonly used grinding and crushing tests, which models (or practitioners) use a particular combination of tests and draws some relationships between the incompatible tests based on the DJB Consultants Inc. database of projects.Case studies will demonstrate similarities and differences between major mining districts with some comments about homogeneous and heterogeneous behaviour within the grindability results.INTRODUCTIONThere are a number of bench-scale grindability tests in use for sizing and predicting throughput for grinding circuits. Part of the reason for this variety is there are a number of different grinding models in use in the Industry, and those models operate using incompatible test results as input (Doll and Barratt, 2008).By using the database of testwork in the DJB Consultants, Inc. (DJB) Millpower 2000 database (see Table 1), some of the more commonly used tests are compared and relationships will be drawn."

Jan 1, 2011

By James Anstey

BHP Billiton?s Cannington facility is a mining and minerals processing plant near Mt. Isa in Central Queensland, Australia, producing silver, lead and zinc. Mine ore is processed in a concentrator, which consists of grinding, flotation, thickening and filtration. Grinding is carried out in a fully autogenous (AG) mill. The mill operates in closed circuit with a pebble crusher. Throughput is approximately 380 tph. Cyclone overflow from the grinding circuit is fed into a flotation circuit for the recovery of lead, zinc and silver. Two concentrates are produced (lead and zinc), which are then thickened and filtered. The filtered concentrate is transported by road to a rail receiving station. From here the concentrate is railed to port in Townsville for shipment to the smelter. Matrikon and Engineers at BHP Billiton?s Cannington Mine have used ProcessACT to develop a flexible, nonlinear dynamic simulator for the grinding circuit to further enhance process understanding, as well to investigate various optimization strategies. An online charge volume estimator was also developed for the AG mill to aid in the understanding of overload conditions, which for the previous two months had been the primary contributor to downtime. The models were developed using a combination of first-principles modeling along with input-output dynamic responses. Examples of models used include: Morrell ?C? model for power and charge shoulder/toe angle prediction; Whiten?s mixing model for breakage and hold-up; Nageswararao cyclone model for predicting cut size; slurry recovery and water recovery. The composite model simulates system dynamics starting from the stockpile reclaim system and finishing at the feed for the flotation process. The objective was to provide a tool that assisted Cannington in understanding their Grinding Circuit and allowed them to develop and evaluate circuit optimization strategies. BHP Billiton Cannington Mine is now considering development of a Grinding Circuit Optimizer utilizing the models developed for the simulator.

Apr 1, 2005

By G. M. Ritcey, K. E. Haque, S. H. Lucas

"Laboratory-scale hydrochloric acid leach tests were conducted on an Elliot Lake uranium ore. Hydrochloric acid leaches without an oxidant or with molecular oxygen (i.e., air or pure oxygen gas) as an oxidant favoured uranium and radium extractions. Conditions for maximum uranium, thorium and radium extractions with hydrochloric acid in the presence of sodium chlorate were determined. The highest extractions of uranium (96%), thorium (81%) and radium (91%) were obtained using a mixture of 44.0 kg HCI and 2.5 kg NaCIOJ per tonne of ore at 75°C with 18 hours ' retention.Flowsheets for two-stage leaching are proposed. The residues obtained from the second-stage leach contain uranium (0.002%), thorium (0.006%) and radium (15 to 20 pCi/g). Tailings of this nature are considered suitable for mine backfill, and, if pyrite is removed, suitable for surface disposal.IntroductionThe nuclear energy industry forecasts an increasing demand for uranium. This increasing demand requires not only largescale mining and processing of conventional and complex uranium ores, but also leads to the consideration of new and nonconventional sources of uranium, e.g., black shales, phosphate rocks, granite, sea water and fossil-fuel ash."

Jan 1, 1980

By S. W. Stogran

"Chemical and limited biological monitoring of mine and mill effluents are being used by regulatory agencies to monitor and control discharges to the environment. Amendments to the Federal Fisheries Act may make it mandatory for mines to conduct Environmental Effects Monitoring (EEM) which will change the emphasis from monitoring effluents to monitoring impacts on receiving waters. The EEM amendments may expand the scope of present environmental studies to include: effluent mixing zone delineation; inventory and classification of resource, habitat, and historical receiving environment; effluent quality determination; chronic and acute bioassay testing; tissue analysis; benthic invertebrate monitoring; fish population surveying; fish tainting evaluation; and the evaluation of impacts on fish habitat, invertebrate communities and fisheries resources. The requirements for EEM have not yet been worked out by the mining industry and the government committee. Experience at Lakefield Research in conducting biological monitoring studies for the mining industry has shown that biological monitoring may be useful for assessing environmental impacts only if programs are planned and executed to collect relevant data, thus minimizing costs and maximizing effectiveness.IntroductionThe chemical monitoring of effluents and water bodies receiving effluents is common practice in the Canadian mining industry and has been used routinely by regulatory agencies to control discharges to the environment. Biological monitoring has also been used on a limited basis, primarily to augment chemical data collected. A number of regulatory bodies, primarily in Canada and the United States, have been incorporating biological monitoring into environmental regulations.Various forms of biological monitoring techniques have been used in Canada and the United States to help assess the impact of mining operations and effluents on the environment. Biological monitoring includes a wide range of activities, from monitoring metal uptake in individual organisms to examining the population dynamics in ecosystems. The most commonly employed biological monitoring techniques are the chronic lethality toxicity tests. Also becoming widely used are in situ and chronic toxicity tests."

Jan 1, 1994

By D. Lindeman, R. M. Nendick

"From a technologist's point of view, there have been few fundamental 'breakthroughs' in the process of gold extraction since the turn of the century. However, the industry has made a great deal of progress in its response to the problems that have arisen: a changing demand for products, lower grade and more refractory ores, inflated labour and materials cost and the increasing control of governmental legislation. The trend in North America and South Africa to alleviate these problems has been to adopt a common policy to process larger tonnages of lowgrade ore through more efficient milling circuits. Here, however, is where the similarity ends.The purpose of this paper is to emphasise the different principles of practice employed by extraction plants in North America and South Africa to achieve the same common goal, namely gold bullion.2.0 INTRODUCTIONTwo very important aspects of extraction metallurgy for which the metallurgical engineer is responsible are plant design and plant commissioning.In North America and South Africa the importance of these aspects is due to the fact that both are related to the financial success of the project of which they form part. Good design is imperative if the capital invested in both the plant and the whole mining undertaking is to reap maximum profit. Furthermore, good design leads to a carefully planned and well executed start-up procedure resulting in bringing the plant into production on time, at designed efficiency and within budget.Due to the competent nature of the quartz pebble conglomerate and quartzite ore on the South African Witwatersrand, the characteristics of the ore type are not much different from one mine to the other. Thus a significant operating knowledge and experience has been built up over the years and there is considerably less risk in selecting a gold extraction process route."

Jan 1, 1992

By Kyle Selga, Christopher J. Greet

"The Pulp Chemistry Monitor (PCM) has been installed and operated in a number of concentrators in Australasia, and has produced some very interesting results. PCM measures the pH, Eh, dissolved oxygen, temperature and oxygen demand of process streams within a concentrator continuously and in real time.In the example presented in the paper the cleaner feed pulp chemistry is measured, and related back to changes in the mineralogy as well as variations in metallurgical response. For example, a decrease in Eh and dissolved oxygen as well as an increase in the oxygen demand. These changes in the pulp chemistry appear to coincide with increases in the feed grades, probably higher pyrite grades. Further, these variations in pulp chemistry and feed mineralogy have a negative impact on the concentrate grade and recovery.The implication is that if the pulp chemistry is monitored it is possible to predict changes in the mineralogy of the system, and from this the metallurgical response. Further, the changes in pulp chemistry can be used in a control system to counter the changes in mineralogy and maintain the metallurgy.IntroductionIt has long been recognized at a fundamental level that the flotation behaviour of sulphide minerals is dependent on the pH and Eh of the system (for example: Tolun and Kitchener, 1964; Woods, 1976). However, measuring pulp chemical parameters within an operating concentrator has had limited attention. Woodcock and Jones (1970a and b) were among the first to actually collect data from operating plants. Jones and Woodcock (1984) identified some of the chemical complexities of flotation pulps, and noted that most concentrators already operate at high levels of metallurgical performance but there was still considerable scope for improvement. These gains would, in part come from more effective chemical control. In the same volume, Healy (1984) discussed metal ion hydrolysis and precipitation, redox chemistry and how the surface chemistry of sulphide minerals can be influence flotation behaviour. The impact of grinding environment on the pulp chemistry and flotation response of a complex polymetallic sulphide ore is discussed by Forssberg and Subrahmanyam (1993). Their work essentially contrasts the pulp chemical and flotation performance of pulps ground with conventional ferrous grinding media to a fully autogenous system. The data suggested that the reduction or removal of iron hydrolysis contamination from the system could have a positive influence on flotation behaviour, and perhaps the first stage of “controlling” the chemistry of the system should be in the grinding circuit. Grano et al (1995) demonstrated that the collection of pulp, solution and surface chemical data could identify weaknesses within a concentrator, and from these data develop, test and implement solutions that improved the process. Greet et al (2006) showed that the pulp chemical trends observed through primary grinding and rougher flotation circuits of most sulphide flotation concentrators are approximately the same. There are differences in the magnitude of various pulp chemical parameters (pH, Eh, dissolved oxygen, temperature and oxygen demand) as a result of variations in the feed mineralogy and processes employed. Further, it was noted the Eh shifted to more reducing values of the ten days measurements were collected, and this change could be traced to an increase in the iron sulphide content of the feed. Metallurgically, this resulted in an increase in nickel recovery through the recovery of nickeliferous iron sulphides, and a decrease in nickel concentrate grade."

Jan 1, 2016

The common theme of these four objectives is declaration. Declaration tells the compiler that an entity exists and also provides the name and nature of the entity. Since everything you create has to be declared, you must know how to declare correctly and be able to make appropriate use of all the declaration tools available to you. This objective recognizes the importance of declaration by requiring you to know everything about Java declarations Write code that declares, constructs, and initializes arrays of any base type using any of the permitted forms both for declaration and for initialization. This objective addresses your understanding of all aspects of arrays. Arrays are the simplest possible data collection and are supported by all modern programming languages. However, Java?s arrays are different from those in other languages, especially C and C++, because they are actually exotic objects. This objective recognizes the importance of being able to make use of all the functionality of arrays. You will be expected to know how to declare, construct, and initialize arrays.

May 1, 2011

By L. C. St. Arnaud

"Open pit mines can produce large disturbances within regional hydrogeologic systems. The degree of disturbance and the consequences on the local environment depend on the size of the pit and on the physical setting of the mine. Comparisons and contrasts are presented for three Noranda base metal open pit mine sites.The Brunswick Mining and Smelting No 6 open pit has a surface area of 11 ha and a depth of 185 m. It is located within complexly deformed schists and meta-volcanic rocks. The massive sulphide and iron formations visible along the north and southwest walls of the pit generate acid drainage. Mining ceased in 1983, and the pit is presently being filled with waste rock and neutralized drainage water. Water balance calculations estimated a total fill up time of sixteen years. As the water level rises, leakage to groundwater could take place across a fault zone intersecting the pit.The Mattabi Mines F-Group pit has a surface area of approximately 3 ha and a depth of 50 m and is also set in meta-volcanic rocks and acid generating iron formations. Production at this site ceased in 1982, and the low pH pit water is neutralized and pumped into a nearby lake at least every five years. Major water inflows are from precipitation and groundwater. Groundwater mounds within adjacent high land surrounding the pit provide a natural hydraulic barrier to groundwater flow, except for the southeast side. As a consequence, the pit water elevation is being kept below the elevation of the nearby creek in which some of the pit water could drain.The Bell Copper open pit covers an area of 40 ha and is 270 m deep. With present ore reserves, the mine might be in operation until 1992. The geology around the pit consists of andesitic tufts, siltstones and shales, and the acid generation potential of the rock is relatively low. A recent hydrogeological study estimated fill up time by precipitation and groundwater to be in the order of 260 years.With increasingly more stringent requirements for mine closure, it is anticipated that more detailed hydrological and hydrogeological studies of open pits will be required to determine post-closure environmental impacts and the suitability of open pits for mine waste disposal."

Jan 1, 1990

By A. Pratt

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

May 1, 2010

By Tapio Leskinen

"In the 1960’s, when large flotation machines appeared on the market, this was a part of a world-wide trend towards the use of ever larger machine units.One factor that has played a decisive part in this development is the increased of the amounts of ore that have to be handled as the exploitation of successively poorer ores becomes necessary. The advancing application of instrumentation and automation has worked in the same direction.In 1970, a working group was set up within Outokumpu Oy, for the purpose of flotation machine development. The principal task of this group was to be the design and development of- a new type of rotor of increased efficiency, especially for the dispersion of large amounts of air- a mechanical-pneumatic flotation machine of substantially larger size that existing plant.This development project required an extensive program of theoretical investigation and experimental studies at several concentration plants of the company.The commonest flotation machine presently used in the concentration plants of Outokumpu Oy is the VK-3. It is of the mechanical-pneumatic type, and the volume of its cell tanks is 2.5 m3 per shaft. This machine was developed within the company, and its first development phase i s represented by the OKKO 3, built for the Kotalahti concentrator in 1959. It was, in its time, comparable in volume to the largest machines that were then in use anywhere in the world."

Jan 1, 1976

By Goutam H. Shahani

Today, the mining and mineral sectors are being impacted by highly fluctuating supply ? demand, extreme price volatility and tremendous market uncertainty on a world-wide basis. This pattern is expected to continue for the foreseeable future. In particular, large consumers of tonnage quantities of industrial gases (oxygen, nitrogen) all have to make informed investment decisions in this uncertain economic environment. Plant owners ? operators need to carefully examine their current and future industrial gas needs in order to develop the most cost-effective industrial gas plant configuration. This can be done by partnering with an experienced engineering company that offers a complete technology portfolio for producing industrial gases. Ideally, the mineral and engineering companies have to work together as a single team to identify the most efficient and economic plant design. This includes an in-depth assessment of capital and operating costs, in order to deliver an optimal solution, taking plant reliability and process safety into account. It is important to consider all the industrial gas needs at a given manufacturing complex, in conjunction with available utilities and infrastructure to develop the best possible long term solution. Oxygen (O2) requirements include: oxygen enriched and oxy-fuel combustion, smelting and hydrometallurgical operations. Nitrogen (N2) is used for annealing. All of these industrial gas requirements have to be examined at a given site over a long term horizon in a holistic manner. Cryogenic air separation was first practiced at a commercial scale in 1902. Since then, the technology has been constantly refined to reduce cost; and improve reliability and flexibility. Today, using advanced engineering techniques, including proprietary process simulation, and modern fabrication techniques, it is possible to build air separation plants that are both low cost and high quality at the same time. It is important to work with an engineering company that owns a complete portfolio of industrial gas technologies, functional engineering capabilities and a variety of plant solutions. Such a partnership can quickly identify a ?sweet spot? for a given situation. By drawing on experience gained from hundreds of projects, it is possible to quickly optimize a given requirement. In situations where a customer wants a complete solution it may be appropriate to provide an air separation plant on a turn-key basis. This will enable the mining and mineral processor to focus on their core business. By using global procurement and construction capabilities it is possible reduce cost and improve project execution, thereby making industrial gas plant procurement simpler and cheaper for the mining and mineral sector.

Nov 1, 2011

By R. H. Seraphim

"Western Mines Limited produces gold, silver, copper, lead and zinc from a number of Paleozoic volcanogenic deposits near Buttle Lake on Vancouver Island. The deposits were emplaced along a series of submarine linear volcanic ridges that extended for at least 6,000 metres in a northwesterly direction.Rock types mapped include: andesitic, dacitic and rhyolitic flow s and volcanic breccias; detrital breccias, tuffs and hematitic silts; black and green cherts; and a variety of dykes and sills, including quartz porphyry and diorite. Orebodies are associated invariably, and in places intimately, with quartzsericite schist and rhyolitic rocks. The ore is complex, varying in mineralogy and tenor both within each deposit and from one deposit to another.Recent studies have increased our knowledge of the structure and left no doubt that the orebodies were deposited both within the throats of the linear vents and on paleoslopes adjacent to these vents.IntroductionWestern Mines Limited operates an 850-tonne-per-day mine, located 85 km south of Campbell River, B.C. The mine is at approximately 400 metres elevation, near the south end of Buttle Lake on Vancouver Island (Fig . I). It has operated since early 1967 and produced 3,650,000 tonnes with an average grade of 1.9 g (0.06 oz) gold, 93 g (3.0 oz) silver, 1.6 per cent copper, 1.0 per cent lead and 7.5 per cent zinc per tonne by the end of 1978. Current reserves are 1,157,000 tonnes of 2.7 g (0.09 oz) gold, 117 g (3 .8 oz) silver , 1.2 per cent copper, 1.2 per cent lead and 8.0 percent zinc per tonne (December 31, 1978).Ore from one zone, known as Myra High-Grade, is mined and milled separately because of its grade. Ore milled prior to December 31,1978, plus reserves, 180,715 tonnes of6.6 g (0.21 oz) gold, 554.5 g (17 .7 oz) silver, 0 .8 per cent copper, 3.2 per cent lead and 10.6 per cent zinc are included in the figures listed in the preceding paragraphs."

Jan 1, 1980