Search Documents

"In mills, metallurgical efficiency is important in every step of the operation through to the tails. Different problems which hinder metallurgical efficiency exist in different mills. One such problem occurred in the Bralorne mill at the tailings end of the circuit, where the washing efficiency of the filters was so low that serious losses in dissolved gold occurred.The new cyanide plant at Bralorne went on stream in August 1961. Test work done showed that: a flowsheet of grinding in water, jigging, thickening, agitating, followed by double filtration, gave satisfactory results and was more economical than a counter current plant. Two filters, 141 x 161, with approximately 700 square feet of filtering surface on each, were purchased and installed in series. Test work showed that this was ample filtering area for 500 tons per day.When the plant started up a density of 45% solids was maintained in the agitators, and a 20 ounce cotton dl1ck was used on the filters. Vacuum was between 23 - 25 inches. Under these conditions the filters would not work and only picked up a very slight skim of pulp. Various speeds were experimented with, 4 minutes per revolution being the most efficient. At this speed the thickness of the pulp on the filters increased to about 1/8”• It was therefore quite apparent that, under these conditions, the filters would not handle very much tonnage and the mill tonnage would have to be reduced drastically until the problem was solved."

Jan 1, 1967

By T. C. Crosby

"Grinding has a marked effect on concentrator recovery and operating cost, and improved operation through automatic control can enhance plant performance. The correct application of automatic control can only be accomplished after the basic process variables and their effect on mill operation have been defined. This paper develops a control system for a closed circuit grinding system. Typical control systems, such as those for feed, water flow, level and circulating load, are discussed. A method of determining controllability, using the calculated reaction curve technique, is outlined. Various successful automatic grinding control applications are discussed and future possibilities are outlined. Although this paper primarily deals with closed wet grinding• circuits, the principles involved can be readily applied to other processes."

Jan 1, 1967

By Gordon MacVean

The object of this paper is to present for your consideration some of the present-day trends of safety practice in the coal mines in the United States and Canada. Coal mining at its best is a hazardous occupation. Men must be experienced miners in order to appreciate the existing hazards and must remain ever conscious of them if they are to work safely. The question is often asked whether our efforts for increased safety are showing results. So often it appears that strides are made for a period of a few years in the reduction of fatalities and lost-time accidents only to have all ground lost by an unfortunate year, after which progress is commenced again only to have a repetition of the same thing. Table No. 1 is an answer to this question. It shows the fatality rates over the last two decades in the coal mines of the United States and Canada. These are given in divisions of five years. The general trend is noticeably downward, exceptions being due to explosions or disasters which claimed an unusually heavy toll of life. These last are certainly not as common today as they have been in the past. It is only reasonable to suppose that this trend towards a lower fatality rate is the result of well directed safety effort. Reliable statistical organizations have offered figures to the effect that only 15 per cent of all accidents can be eliminated by the use of mechanical safeguards. The state of mind of the man involved, or his attitude towards safety, commonly called 'safety-consciousness,' is the controlling factor in the prevention of 85 per cent of our accidents.

Jan 1, 1931

By H. J. White

The effect of alloying elements on the mechanical properties and weldability of wrought gamma prime strengthened nickel- base superalloys is well known. An understanding of the basic guidelines concerning alloying additions has led to the invention and development of HAYNES® 282® alloy for applications in aircraft and land base gas turbines and other high-performance high-temperature environments. The alloy combines exceptional high temperature properties with good weldability and fabricability. At high temperatures (~ 900 °C), the alloy is stronger in creep strength than Waspaloy alloy (UNS N07001) and it approaches the creep strength of R-41 alloy (UNS N07041). Because the alloy has better thermal stability, fabricability, and weldability than Waspaloy and R-41 alloys, it is currently being considered as a candidate universal consumable for welding/ repair welding of gamma prime strengthened nickel based superalloys and it is also being considered as a suitable replacement for applications where R- 41, Waspaloy, and 263 (UNS N07263) alloys are currently being used. The alloy was designed to have improved resistance to strain age cracking, a problem common to gamma prime strengthened nickel based superalloys. In this paper, we present (1) results from hot ductility testing of annealed and annealed/aged material; (2) results from Time Resolved X-ray Diffraction (TRXRD) studies during a welding thermal cycle of annealed and annealed/aged material, and (3) gas metal arc (GMA) and gas tungsten arc (GTA) welding of annealed and annealed/aged material.

Jan 1, 2010

By F. Habashi

"While bioleaching of pyrite concentrates has been successfully used in industry to liberate gold from the sulphide matrix for subsequent cyanidation, the same technology cannot be recommended for leaching chalcopyrite concentrates for copper recovery. It will be shown to be uneconomical and cannot compete with pressure leaching technology. Data on the pilot plants that were constructed for this purpose and were shut down will be given.INTRODUCTIONBacterial leaching has been successfully applied for heap leaching of low-grade copper ores (Habashi, 1978, 1999). One of the major operations is that at Bingham in Utah (Figure 1). The leach solution collected at the bottom of the heap is extracted by organic solvents and the strip solution is electrolyzed to get high purity copper. The process was extended to treat auriferous pyrite concentrates to liberate gold and render it amenable to cyanidation by a process known as BIOX (Marsden & House, 2006; Lunt & Briggs, 2005).BIOX plants currently or recently in operation are the following:??Ashanti Goldfields Company, Ghana. Designed with an initial capacity of treating 720 tonnes of concentrate per day, the Sansu plant has since been expanded and currently has four modules processing 960 tonnes per day in all. It is by far the largest biooxidation plant in the world. The capital cost of the plant totalled US $25 million (1994 terms) and the operating cost is currently US $17/tonne milled.??Fairview, South Africa. The plant at the Fairview mine in Barberton, which was the initial pilot plant, has been fully operational since 1986. It was originally designed to treat 10 tonnes/day of concentrate but with the success of the project this has been increased to 55 tonnes per day. With the purchase of Fairview by Avgold’s Eastern Transvaal Consolidated, Avgold concluded a licensing agreement with Gold Fields, formerly known as Gencor, entitling it to use the BIOX technology to treat itsconcentrate.??Saõ Bento, Brazil. A BIOX plant was recently in operation in Brazil at the Saõ Bento Mine where a pressure oxidation circuit is used to treat the refractory flotation concentrate. This plant has confirmed the viability of combining bio-oxidation with pressure oxidation as a cost-effective method ofincreasing capacity at an existing oxidation plant.??Wiluna, Australia. The plant at Wiluna Gold Mine, Western Australia, was commissioned in 1993. Although originally designed to treat 115 tonnes per day of concentrate this has subsequently been increased to 158.??Other plants at Tamboraque in Peru, Harbour Lights and at Youanami in Australia have been commissioned recently."

Jan 1, 2012

By M. Li, T. H. Dubaniewicz, H. N. Dougherty

"INTRODUCTION Underground mines have the risk of accumulation of gases if not ventilated properly or during and after emergency situations when ventilation controls become damaged or stop working. Common gases that are monitored in underground coal are carbon monoxide (CO), oxygen (O2), and methane (CH4). Methane is a gas found in coal and released through mining; its explosive range is between 5% and 15%. Methane is commonly monitored on all mining equipment and with handheld gas sensors carried by most underground coal miners. Fiber optics (FO) is a popular technology applied in underground mining, particularly for its electric isolation. Many miners are familiar with FO cables hung throughout the mine, which are primarily used in the communication of voice and data (Taylor et al. 2010). Advancements in laser and fiber optics have made this technology well suited for gas sensing the harsh environment of mining applications. The work of the U.S. Bureau of Mines on the use of fiber optic monitoring of gases in mines started in 1992. Dubaniewicz et al. (1992, 1993, 1995, 1999, 2003) developed prototype gas sensors, including methane gas sensors, for research purposes. Previous research (Dubaniewicz & Chilton 1992) identified potential fiber optic gas detection cross-sensitivities associated with the index of refraction of various gases. Index of refraction effects was noted for carbon dioxide (CO2), which is produced in significant quantities by mine fires or explosions. NIOSH released a broad agency announcement (BAA) for the development and demonstration of mine safety and health technology (CDC NIOSH 2017). The objective of this announcement was to validate a sensor, specifically fiber optic, for the mine environment and test it in an actual working mine. The RSL FO sensor “OptoSniff” provided from this work is capable of hundreds of sensing points over distances of up to 20 km, has a measurement range of 0.05% to 100%, senses in an oxygen- deficient environment, and has no gas cross-sensitivity (RSL, 2014). The RSL system is totally electrically passive outside the central control unit (CCU), which can be housed in an MSHA-approved explosion-proof (XP) enclosure or in a control room outside of the permissive area. The sensor was tested in dusty and signal loss situations, showing it is tolerant of dust, has functioned at signal losses up to 90%, and was successfully tested in a mine environment for a five-month period (Walsh et al. 2014). This paper describes how the RSL FO sensor is used for testing using smoke and its contaminants for applicability in emergency situations. The testing investigates individual contaminants such as CO2, temperature, and smoke. Each test was performed separately and methane concentration, laser power, and response time data were collected."

Jan 1, 2019

By Jae-sang Ahn

As the amount of construction information used in the growing construction field increases, the importance of efficient construction field management has been growing. Therefore, construction industry have been tried to introduce and conjugate various software and IT technology such as PMIS, Web Camera, RFID, GPS, PDA. However, existing IT technology especially PMIS have not been performed systematically because of difficulty of real time information collection and decision-making from the insufficient handy equipment. These problems make construction manager cannot efficiently respond to diverse condition occur in construction sites. In addition, after the completion, individual who use PMIS have to move another site and use another system so than cannot use information from previous sites. On the other hand, development of IT technology transmute PDA phone for text-based work like schedule management, internet research to smart phone for network based multimedia service. In other words, smart phone is not just IT equipment but new way for overall industry and it can satisfy the demand IT technology on construction sites. Therefore, the purpose of this study is introduce mobile based individual unit PMIS system using cloud computing and SNS which is in development progress. It is expected to be possible to collect and record the real-time information that occur at the site and make rapid decisions based on the recorded information, by converting the office works that are managed based on the site PC or Web, if the site management system that is based on the smart phones and Cloud computing that will be constructed through this research are utilized. After this study, it is necessary to research about interwork with project unit PMIS system and test on real construction site.

Aug 1, 2013

By P. Morissette

Passive monitoring of support performance during rockbursts was conducted at three deep underground mines. A comprehensive database was constructed of 172 seismic events and the associated damage to support systems at 266 mine locations from January 2000 to September 2012. The majority of pertinent information was obtained through seismic system records and on-site field assessments. This work assesses the quality of collected information and evaluates the dynamic-load demand on support systems in seismically active mines.

Aug 1, 2013

By A. Zrimsek, G. Vingas, R. Wolke

IN 1952, prompted by the great demand of the Canadian drilling and foundry industries for sodium bentonite, the Geological Department of Magnet Cove Barium Corporation, Limited began an extensive search for bentonite deposits throughout western Canada. Their efforts were rewarded in 1958, when substantial deposits of high quality material were found approximately 100 miles southeast of Edmonton, Alberta. The bentonite material, a part of the Edmonton formation in the Upper Cretaceous, is located approximately nine miles south of the town of Rosalind. The land where the bentonite lies has in places .been eroded by stream and glacial action to form a wide gully, convenient for strip mining methods (see Figure 1). The bentonite bed is almost flat-lying, dipping to the southwest at approximately 12 feet per mile. The main bed is 8 to. 10 feet thick and is covered with 15 to 25 feet of overburden. Before stripping, the area is drilled and sampled to evaluate the quantity and quality of the bentonite.

Jan 1, 1962

By E. A. Cleveland

A glance at the map discloses the fact that the Pacific Great Eastern railway either traverses or crosses some of the most important rivers of the province: the Squamish with its branches the Stawamus, Mamquam and Cheakamus; and the Green, Lillooet, Birkenhead, Fraser and Quesnel rivers. Each of these and some of their tributary streams, having their ?sources and upper reaches in the higher altitudes in regions of abundant snowfall, is capable in greater or less degree of furnishing water under suitable heads for the economic production of power. Beginning at its present terminus at Squamish the railway has the only hydro-electric development within its territory among the whole list of streams mentioned. A 225 horsepower installation at the edge of the East branch of the Squamish river, using water from Stawamus river, a branch of the former, under a head of 418 feet, is a modest beginning. Two or three additional sites, where water may be used under somewhat similar heads, may be found on this little stream. Next above Squamish, along the route of the railway, is the Mamquam, a long tributary of the Squamish from the eastern slopes. It has a drainage area of something like 130 square miles with widely varying discharges of from less than 50 to about 14,000 cubic feet per second. The preliminary investigations so far have disclosed no suitable storage sites, so the Mamquam may be regarded as a small continuous power stream - probably less than 1000 horsepower.

Jan 1, 1925

This paper describes results of an investigation of fracture during tube expansion of 5052 and 5754 aluminum seam-welded tubes to optimize the forming of aluminum tubes during hydroforming. The tubes were produced in laboratory by press forming of tubular blanks and pilot-scale high frequency induction welding. The effect of property mismatch between the weld and base metal has been investigated. The material work-hardening was obtained by roll forming of sheet blanks in the 0-temper and H32 temper condition. The results showed that a significant work-hardening can be present in aluminum tube without causing weld fracture during tube expansion. The work-hardening increases the yield-strength mismatch between base metal and weld. Annealing reduces the hardness of base metal leading to more uniform deformation during tube expansion. As a result the occurrence of weld fracture is reduced. The study showed significant deformation of the welds during tube expansion. Weld thinning can be as large as parent-material thinning before fracture. To avoid fracture at the weld joint, good formability and high yield strength of the weld is needed. FEM simulation showed that minimizing the width of the weld joint can reduce thinning of the weld.

Jan 1, 2004

By C. J. Hodgson

"IntroductionThe Kitsault molybdenum mine is located 600 m above sea level on Lime Creek at the head of the inlet of Alice Arm, 140 km northeast of Prince Rupert, British Columbia (Fig. 1). The area of the mine is characterized by rugged topography and deeply incised creeks which drain into the Portland Canal - Observatory Inlet fjord system. Access is by air service or boat from Prince Rupert, or by secondary road from Terrace.HistoryThe deposit was first staked in 1911, at which time the main feature of interest was a polymetallic vein with values in silver located southeast of the molybdenum deposit (Woodcock and Carter, 1976). Turnbull (1916) was the first to describe the extensive zone of crisscross quartz stringers with Mo~ on the banks of Lime Creek which, although it clearly had the potential to contain a major deposit, was not then believed to be of commercial value.Following sporadic work through the 1920s and early 1930s, the ground lay idle unti11959 when Kennco Explorations (Western) Ltd. commenced a program of systematic diamond drilling on the stockwork-type mineralization adjacent to Lime Creek. In late 1964, Kennco announced the presence of an orebody of 36 million tonnes averaging 0.230Jo Mo~ which was to be put into production at a rate of 5450 tonnes per day under a new subsidiary, British Columbia Molybdenum Ltd., at a forecasted capital cost of $20 million (revised to $30 million).Between January 1968 and April 1972, 10.4 million kg of molybdenum were produced from 9.3 million tonnes of ore, at an average mill recovery of 90%, and with an average mill head grade of 0.206% Mo~. The ore was mined in an open pit with a waste to ore stip ratio of 1.5 to 1. The. operation was terminated in 1972 due to weak molybdenum prices and escalating costs.In May 1973, the deposit was purchased by Climax Molybdenum Corporation of British Columbia, Limited and in 1979 transferred to affiliate Amax of Canada Limited. In early 1979, following completion of detailed feasibility studies, Arnax commenced construction of the 10 900 tonne per day Kitsault mine and mill complex based on a mineable open pit reserve of 95 million tonnes at an average grade of 0.192% Mo~, sufficient for a mine life of 25 years. The original capital cost estimate was $143 million; it subsequently escalated to approximately $200 million."

Jan 1, 1995

By Du Xinfeng

The resource quantity of the low rank coalbed methane (CBM) accounts for 47% of the total resource quantity of CBM in China. Compared with the exploration and development of the high rank CBM in Qinshui Basin, China and the low rank CBM in Powder River Basin, USA and Albert Basin, Canada, the exploration and development of the low rank CBM are still in the initial test stage. In this paper, on the basis of analyzing the mining geological conditions such as that the Huanglong Jurassic Coalfield is largely situated in the hills and gullies zones, and the coal reservoir has the features such as the low metamorphic degree, large coal seam thickness, simple coal matrix texture, high permeability and small CBM content and so on, it discusses the key technologies such as the development pattern of CBM, well location arrangement, drilling and well completion technology and fracturing technology and so on. It indicates that the underbalanced drilling and the cavity well completion based on the reservoir protection will be the development directions of the CBM development technology in this area.

Aug 1, 2013

By Jun Dai

Based upon research findings from several countries, the combination of microwave and mechanical means to break hard rock holds promise for the future. To achieve this goal, it is essential to understand the laws governing strength reduction of hard rock, such as granite, induced by microwave irradiation. Two aspects to consider are: 1) laws associated with the tensile strength of hard rock after microwave irradiation and 2) the sensitivity of different types of rock strengths to microwave energy. In this study, granite with a range of tensile strengths was exposed to microwaves for various time periods to compare the response of rocks with different strength values exposed to the same microwave irradiation. In addition, a method based on hotspots is presented to explain the mechanism by which granite strength is reduced by microwave irradiation. Granite extracted from Qinling Mountain in Shaanxi Province, China is used in the research. ?50 × 50 mm cylindrical granite specimens were exposed to microwaves at a specific power level. The strength values of the heated granite specimens were compared with those of unheated specimens. Through the comparison and analyses, relationships were determined between 1) reduction in granite strength and microwave irradiation time period, and 2) granite strength and sensitivity to a given energy of microwave irradiation. Finally, a mechanism to explain the experimental results is proposed. Research findings will aid in the design of a microwave + machine rock-breaking system for use in rock breakage in underground mines at depth and for future mine applications on earth and other planets. In addition, the experimental approach could be used to test other rock types to further our understanding of rock damage induced by microwave irradiation.

Aug 1, 2013

By P. Personnet, D. Wheaton, E. Couzinie, V. Demetriou, Brooks. W., G. Girault, M. Meyer, L. Charbonnel

A common problem in Gas Treatment Centers (GTC) from primary aluminium smelters is the temperature of the gas to be treated : above a threshold, filtering media are irreversibly damaged. The traditional way of dealing with high gas temperature is to dilute with fresh air, which implies over sizing - and therefore higher cost for - the GTC in order to have the capacity to treat this dilution air without compromising on pot suction. A system was developed which decreases gas temperature without having to use dilution air. This system is based on water pulverization in gas collectors. The water vaporization leads to a temperature decrease of the gas. A pilot system was trialed in our R&D unit. Satisfactory results led to the development of an industrial system based on Envirocare equipment (partnership), which was trialed in our production plant in Tomago (NSW, Australia). This patented system was then generalized in this plant, which is now using it with success during austral summer.

Jan 1, 2006

By J. Illescas, N. C. Murray

This paper provides an economic comparison and technical evaluation of different approaches for copper recovery from small-scale resources such as historic tails, dumps, pond and pit water as well as acid mine/rock drainage. Factors such as the location, the availability and cost of reagents, power availability and cost and a local market for end product alter the preferred processing technique. A number of scenarios are presented and technologies considered include; solvent extraction, ion exchange, sulphide precipitation, cementation, copper sulphate crystallization, membrane (RO) and copper cathode production.

Jan 1, 2014

By O. F. Carter

"Coniaurum Mines, Limited, hold nineteen claims in Tisdale township, in the Porcupine district, adjoining the McIntyre mine on the east. They extend for over a mile along the strike of the Hollinger-McIntyre 'break'. The property has been explored extensively along the ore zone both laterally and vertically. Workings have been carried to a depth of 5,500 feet, and nearly 50 miles of lateral workings (drifting and cross-cutting) have been driven to date in development and in gaining access to the orebodies.Production started at the Coniaurum in June 1928 and has continued without interruption. To the end of 1946 the plant has treated 2,695,725 tons of ore, yielding gold having a value of $21,989,918.The Coniaurum is controlled by Ventures Limited of Toronto. Mr. John Redington, who has guided all operations since work began on the property in 1922, is Managing Director.GENERAL GEOLOGYAge and Types of RocksKeweenawan- Quartz diabase dykes.Algoman - Quartz porphyry intrusive; the veins are probably late Algoman.Keewatin - Lava flows.Brief Description of Rock Types.Diabase DykesTwo quartz diabase dykes traverse the property in a north-south direction, cutting all formations, including veins.Porphyry IntrusivePetrographically all porphyries in the Coniaurum are of the usual Porcupine type- quartz-feldspar with alteration advanced in most instances to the stage where the feldspars are completely dissolved, leaving a wellsheared carbonate and sericite matrix with embedded rounded quartz 'eyes'. Alteration is most extensive in the smaller bodies and in the narrow protuberances from the larger masses; the cores of the larger masses are generally much fresher, with more or less well defined feldspar phenocrysts."

Jan 1, 1954

By Z. Y. Ma, H. Y. Yang

The process of microwave-ultrasound assisted leaching of valuable metals from copper anode slime was proposed in this paper. Design of experiments has been used to study the effect of the main leaching parameters, such as microwave power, ultrasound power and reaction time. The central composite design (CCD) was used to predict the maximum leaching efficiency of copper, tellurium and selenium. The experimental data obtained were fitted to a second-order polynomial equation, and they also were analyzed by analysis of variance (ANOVA). The 3-D response surface plots and the contour plots were applied to determine the optimal conditions. The optimum conditions of microwave-ultrasound assisted leaching process were: microwave power 834W, ultrasonic power 638W and reaction time 403s. Under these conditions, the experimental leaching efficiency of copper, tellurium and selenium were 98.88±0.56% 98.96±0.78% and 98.57±0.67%, respectively, which agreed well with the predicted values.

Jan 1, 2014

By W. J. Przybylowicz, V. M. Prozesky, D. de Bruin

"The common style of gold mineralization in the Basal Reef and other auriferous conglomerates of the Witwatersrand Supergroup comprises clusters of gold grains occurring interstitially to quartz and pyrite pebbles as well as gold accumulations attached to the surface of and infilling hairline cracks and fractures in round, compact, detrital pyrite. The latter textural association is generally interpreted as a result of remobilization of originally detrital gold during regional metamorphism and related hydrothermal fluid circulation. There is general agreement that, although gold solubility was low, ore modification occurred during the metahydrothermal event, but uncertainty exists about the magnitude and scale of gold remobilization.Micro-textural and chemical investigation of compact round pyrite and associated gold accumulation has established that gold is preferentially deposited on chemically heterogeneous pyrite surfaces. Combinations of alternating high- and low-As zones in pyrite result in mixed np-type conductivity accompanied by electron exchange and the reduction-driven deposition of gold at the cathode. This model does not explain gold accumulations which are not immediately linked to chemical heterogeneities and it is inferred that an additional control on the deposition of gold was exerted by physical defects which lead to zones of increased charge density and/or areas of focussed conductivity. The inferred precipitation mechanisms suggest that submicrocopic physical and chemical controls are the important factors that determined the sites of gold nucleation and that precipitation mechanisms based on physicochemical changes of the hydrothermal system were not involved. The Basal Reef contains on average close to 5OJo of round, detrital, chemically zoned pyrite which provides a large number of electrochemically active pyrite surfaces. The extremely effective electrochemical precipi- . tation mechanism together with the low solubility of gold in Witwatersrand fluids is the main reason for the spatially restricted remobilization of gold in the conglomerate reefs."

Jan 1, 1994

By D. Gorc, T. M. Fraser, Z. T. Nikic, R. Pesalj

"Mount Polley is an alkalic porphyry copper-gold deposit of Lower Jurassic age within the Quesnel terrane in south-central British Columbia. The silica-saturated Mount Polley intmsive complex is assumed to be coeval with volcanic rocks of similar composition in the Nicola Group in which it was emplaced. Other intmsions and some of the volcanic rocks in the Mount Polley area are silicaundersaturated and contain feldspathoids.The Mount Polley deposit is characterized by multiple intrusions that vary from diorite to crowded plagioclase porphyry to monzonite. Intmsion breccias are associated with some of the intmsive phases. Abundant hydrothermal breccias occur on the margins and above plagioclase porphyry intmsions. These breccias provide the main host for mineralization and are associated with the highest concentrations of copper and gold. The breccias are subdivided into four distinct types based on the dominant hydrothermal mineral in the matrix. Actinolite breccia is developed in an elongate zone within the core of the Central zone and grades laterally and vertically into biotite breccia to the southeast. Magnetite breccia is irregularly distributed and is relatively sparse throughout the deposit and albite breccia is dominant in the West zone. Pervasive and vein-related alteration correlates with the breccia types. The core of the hydrothermal system at Mount Polley is subdivided into three zones: actinolite, biotite and K-feldspar-albite. The margins of the core zone are overprinted by a discontinuous zone of calc-silicate minerals. This intermediate zone passes outward into propylitic alteration. Mineralization is most prominent within hydrothermal breccias and is generally present as disseminations, blebs within the matrix and abundant veins. Mineralization is associated with a chalcopyrite-magnetite-bornite assemblage in the core of the deposit passing out into magnetite-pyrite-chalcopyrite. Relatively constant copper to gold ratios suggest that both metals were precipitated under similar conditions.Hydrothermal breccias are genetically related to the emplacement of the crowded plagioclase porphyry melt. Crystallization of the melt was probably accompanied by volatile/aqueous exsolution, forming a water saturated carapace. Decompression of the chamber in response to magma withdrawal, fracture propagation and possible fault movement allowed hydrothermal brecciation to occur at the apex and margins of the intmsion. Alteration and mineralization appears to have been controlled by fluids migrating away from the plagioclase porphyry."

Jan 1, 1995