Search Documents

By Michael J. Rosko

Methods have been developed for processing and analyzing reflected solar radiation data obtained by Landsat 5 Thematic Mapper multispectral scanner. Spatial resolution for the Landsat series satellites is 30 meters per side per pixel. Materials on the Earth?s surface absorb or reflect different parts of the electromagnetic spectrum depending on their physical and chemical properties and, therefore, typically have characteristic spectral ?signatures?. Using these signatures, environmental parameters such as surface water and vegetation may be identified and analyzed. Principal advantages of the satellite image method for environmental monitoring include: a relatively long historic period beginning in 1985 for which information is available, the reliable numerical basis for the results, and the ability to assemble a historic environmental baseline and provide on-going monitoring for large or remote areas where standard monitoring methods may not be practical. However, because the long-term continued operation of Landsat 5 is problematic due to the age of the equipment, QuickBird and IKONOS satellite images were processed to determine if the two systems are sufficiently similar in their results to allow continuing monitoring using QuickBird data. The QuickBird satellite was launched in 2001 and collects the same visible and near infrared spectral bandwidths as Landsat 5, allowing for equivalent process algorithms for QuickBird, IKONOS, and Landsat 5 data. Spatial resolution for the QuickBird images is 2.4 meter per side, allowing for more detailed characterization of the land surface; spatial resolution for the IKONOS images is 4 meter per side. Because of several differences between the satellite systems, including degradation of the Landsat 5 sensor, it is necessary to calibrate QuickBird and IKONOS results to the Landsat results to verify similarity. Recent images from the satellite systems have been processed and results have been compared to determine the validity of comparing Landsat 5 and QuickBird/IKONOS images so that these newer data can be used reliably in the future instead of Landsat 5 data. Results from this comparison are presented in this paper and suggest that analyses for vegetation using the two satellite systems are comparable, and that little calibration is required. Results from comparison of surface water results from the two systems are less comparable and is currently being investigated by the authors.

Oct 1, 2009

By J. S. Fox

It is generally recognized that the interpretation of bedrock geochemical data in volcanic terrains can be improved by adjusting for rock-type. Various chemical attributes of volcanic rocks have been put forward in the literature as rapid indicators of rock-type, but there is some question as to which of these is the most reliable . Only one such attribute, total iron, seems to have seen systematic use in geochemical mapping in the Flin Flon region. Discriminant analysis of 500 basalts, andesites, dacites and rhyolites suggests that SiO2 is the most important rock-discriminating variable and that MgO, CaO, TiD2, AI2O3 and FeOtot, are successively poorer discriminators. Lithological normalization in the subalkaline volcanic environment should therefore be made over ranges of this variable. Trace-metal data from drill core through the sulphide orebody at Hanson Lake, Saskatchewan are used to demonstrate various approaches to lithological correction, including silica normalization, factor analysis and trend analysis. All of these extract economically important information from the core that is not apparent in the raw data logs. However, silica normalization does not seem to be subject to as many serious limitations as factor and trend analysis in this case, and therefore seems to provide the most reliable basis for the interpretation of subsurface exploration geochemical data.

Jan 1, 1978

By N. Melnyk

"FOREWORDThis paper provides a unique description of a method devised for mining a very thick steeply dipping seam of soft gassy coal which was prone to spontaneous combustion. The editors con¬sider that the information in this paper should be important to those who may have to consider mining such seams again at some time in the future and therefore believe that the paper warrants reprinting in the present volume. The author was ask¬ed to review the paper and to add any additional relevant in¬formation. He provided the accompanying footnote, only a month before his death on April 22, 1982.IntroductionIn the past, the Cadomin Coal Company has opened four mines, all in the same coal seam or its folds. Three of these were opened from river level by horizontal entries or rock tunnels. and the fourth, the present working mine, by vertical shafts. This paper deals largely with some operating phases of this fourth mine, with which the writer has been associated.The seam worked here is a thick, steep, bituminous seam, and the writer feels there is a paucity of published data on the mining of such seams. Possible reasons for this are that such seams do not lend themselves to intensive development or mining, there is little chance to mechanize because of the extreme pitch, and operations are fraught with many problems. In addition the present operations in this particular' seam are being carried on at a level below the former workings, introducing new problems, not encountered on the upper level.Coal will, without question, long continue to be an impor¬tant factor in the national economy, and some of the best coal is to be found in thick, steep seams. But with the exhaustion of the easily-mined coal near the outcrops, future coal will have to come more and more from lower levels. At Cadomin there is still considerable coal on the second level, below the old river-workings, and there is a possibility that, in the future, still lower levels will be worked. It is the purpose of this paper to indicate some phases of such lower-level operations and to invite discussion."

Jan 1, 1985

By I. E. Puddington, F. W. Meadus

The beneficiation of barite in mill tailings using an agglomeration technique has been demonstrated. Barite was selectively absorbed from a conditioned aqueous slurry into a collector oil by mechanically mixing slurry and oil. The resulting oil-bonded barite-containing agglomerate was washed, to remove gangue material, and further mechanically contacted with dilute H2SO4 This treatment resulted in the transfer of barite into the aqueous phase. Grades as high as '97% BaSO4, with recoveries of 80%, have been obtained using this technique.

Jan 1, 1973

By Lorne Sivertson, Peter Kitrredge

"World metallurgical coal imports totalled 110million tonnes in 1978. Of this amount, Japan imported 50 million tonnes, making it by far the largest and most important coking coal market . British Columbia and Alberta exported 12.0 million tonnes of coking coal in 1978, or 11% of the world total. Virtually all of these exports were directed to Japan, making up 22% of total imports.Some observers have suggested that because Japan is almost the exclusive buyer of British Columbia and Alberta metallurgical coal, the benefits of the coal trade may be primarily on the side of the powerful Japanese buyers. Buttressing this suspicion is the fact that Japanese trading companies have taken substantial equity positions in B.C. coal mines, thus presenting the possibility of non-arms-Iength transfer arrangements. There is then at least some evidence to support the hypothesis that Canada's western coal producers receive prices that are less than would prevail in a more competitive market; that is, that they are exploited.This paper produces evidence that Canada's coals are not underpriced in respect to U.S. and world markets. The conclusion is drawn that British Columbia and Alberta metallurgical coals receive prices that are equal to prices known to be competitively determined. This conclusion follows an in-depth analysis of prices, coal qualities and the economic characteristics of all major coals traded in the Japanese market. A by-product of the analysis is an equation capable of predicting the value of any metallurgical coal sold to Japanese buyers, or, for that matter, any buyer. Hopefully, this can be of some use to coal producers in developing their marketing strategies."

Jan 1, 1980

By P. B. Marchant

"Considerable gold and silver values are lost to flotation tailing from both the South ern Tail orebody and the Main Zone orebody,The underlying mineralogical assemblage of the two ore types is quite different. This paper describes the research strategy employed to determine an economical method to scavenge gold and silver from flotation tailing.Much of the unrecovered gold in the Southern Tail ore is associated with arsenopyrite while silver losses are probably as unliberated tetrahedrite and minor silver-bearing sulphosalts. Processing alternatives tested include bulk sulphide recovery by flotation and gravity, selective pyrite-arsenopyrite separation, cyanidation, and oxidation pretreatments such as pressure leaching and bioleaching to enhance cyanidation response. Gold losses in the Main Zone ore are more closely associated with silver-bearing minerals, pyrite, and siliceous gangue and consequently respond more readily to conventional tank cyanidation. The 5 300 tid carbon-in-leach circuit to treat Main Zone flotation tailing is described in detail.IntroductionEquity Silver Mines Limited's open-pit silver mine, a 70% owned subsidiary of Placer Development Limited, is located 37 km southeast of Houston in north central British Columbia. The deposit consists of two major ore zones, Main Zone and Southern Tail (Fig. I). These zones are within a sequence of Cretaceous volcanic and sedimentary rocks striking 015 degree s and dipping 45 degrees west. Feasibility ore reserves were 28 million tonnes grading 106 g A g/t, 0.96 g Au !t and 0.38% Cu a strip ratio of 2.2 to I. A detailed mineralogical description has been presented and a comparison of the two ore zones is shown in Table I."

Jan 1, 1986

By P. E. Cavanagh

FOR THE PAST seven years Mr. W. Simpson, Chief Mechanical Inspector for the Nova Scotia Department of Mines, has carried out exhaustive field trials of non-destructive inspection equipment in the coal mines of that Province. This work has demonstrated the usefulness of a number of types of non-destructive inspection when used for periodic inspection of hoisting and haulage equipment in the coal mines of Nova Scotia. As a result, the Dominion Coal Company has instituted a programme of regular preventive maintenance inspection ?by a special staff of qualified and trained men. The purpose of this present paper is to describe how non-destructive testing techniques are used on ropes, axles, couplings, and other hoisting and haulage equipment, how these methods are being used in other industries, and the expected benefits from intelligent and properly organized use of these techniques in the coal mining industry.

Jan 1, 1956

By F. M. Waldie

THE 2,538-foot belt conveyor recently installed underground at the Sullivan mine hoists ore from the 3,350-foot level to the 3,900-foot or main haulage level, a vertical distance of 680 feet. The design and planning of development work, under the direction of Mr. R. H. Stewart, Consulting Engineer, was begun in the spring of 1941. Development work was started in July of that year from the 3,350-foot level, and headings were started on the 3,650-foot and 3,900-foot levels later in the same year. It was the intention at that time to keep three headings going on development work necessary for the installation of the system: two on the conveyor incline, and one on the 3,900-foot level. This programme was modified in 1942 when there was some doubt whether the material for construction could be obtained. This problem of supply was eventually solved and the development work was pushed to completion in December, 1943. Construction was started in December, 1943, "'under the supervision of Mr. G. H. McKay, Superintendent of Construction and? Maintenance, and was completed in November, 1944.

Jan 1, 1945

By Shuai-Jun Li, Xia-Ting Feng, Xian-Jie Hao

"The anisotropy of rock is of great importance to the rock engineering. To investigate the anisotropic character of slate, the rock samples of slate under different confining pressures and bedding plane angles was conducted on the MTS. The results indicated that the relationship between bedding plane angle and elasticity modulus, friction angle, cohesion and strength was shown as U pattern. The minimum value of them is located from 30°to 45°.In addition, the elasticity modulus and Poisson's ratio increase with the increasing confining pressure. The slate behaves brittle failure both in the uniaxial and triaxial compression. The failure pattern of uniaxial compression is generally tension failure, and triaxial test usually shows shear failure. The failure angle decrease with the increasing of confining pressure.INTRODUCTIONThe anisotropy of rock is that loading in different orientations the rock has different mechanical properties. The anisotropic property of rock is always an important problem in rock engineering (Hoek E. & Brown E. T., 1980). J. C. Jaeger (1960) first presented that transverse strength criterion for sliding fracture on joint surface. Later he revised rock parameters to anisotropy empirically for isotropic Mohr- Coulomb criterion. His main idea is revising cohesion according to loading direction (J. C. Jaeger, 1971). Then, many scholars study a lot on transverse strength criterion. E. Z. Lajtai (1969) considered the influence of connecting rate in all directions in joint groups for shear strength in intact rock; R. Mclamore and K. E. Gray (1967) referenced the theory of J. C. Jaeger. They not only revised cohesion also revised friction coefficient. Y. M. Tien (2000, 2001) made further study on the influence of connecting rate in joint group to transverse strength. R. Nova (1980) studied on the variation of strength when rock specimens in triaxial pressure and complex stress paths. O. Cazacu(1998) put forwards a new anisotropic strength criterion for analyzing rock strength. S. Pietruszczak(2000) introduced fabric tensor for characterizing inner seismic structure and he built an anisotropic strength criterion containing the invariants of stress tensor and seismic fabric tensor."

Jan 1, 2015

By C. Guo, R. J. Chalaturnyk, M. MacKinnon, J. D. Scott

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd. oil sands plant. Over the past years (since 1996), there has been a marked change in the densification behaviour of MFT in the MLSB. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings) at the area with intense microbial activity. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. It may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program was carried out to study the mechanism leading to the rapid densification phenomenon. A review and discussion of the research program is given and some results from the field investigations and small-scale column tests are presented in this paper.

Jan 1, 2007

By I. Lackey

In 2004, Zinifex Budel Zink commenced testing with the objective to increase the precipitation of aluminium in the iron purification stage of its hydrometallurgical zinc circuit, without the use of expensive reagents. Findings from the literature applied to the leach circuit at Zinifex Budel Zink demonstrated that aluminium removal from the leach circuit could be increased by lowering the ferric concentration and acidity in the vessels where jarosite precipitation occurs. An associated increase in copper precipitation was mitigated by limiting the extent to which the ferric concentration was lowered in the vessels where jarosite forms and lowering the ratio of copper to aluminium in the solutions entering these vessels.

Jan 1, 2006

By A. Chamanara

The gross vehicle weight (GVW) of an ultra-class mining truck comprises the unsuspended weight below the struts plus the suspended empty vehicle weight, plus the payload. Theoretically, one third of the suspended total weight is supported by two front struts and two thirds by two rear struts. However, since the payload position is not fixed when placed in the truck body and varies from load to load, compounded by uneven haul road profiles, the truck structure experiences higher than normal stresses, which manifest in the reduction of the life of the truck via structural fatigue. The downstream effects are a decrease in production and increase in operational and maintenance costs. In order to control the dynamic forces causing the high stresses on the truck structure, both the haul road conditions and the load distribution in the truck body need to be investigated. The latter aspect is the prime focus of this paper. A field test has been conducted in an oil sands mine where the Caterpillar 797B trucks are loaded by a Bucyrus 495 shovel. The strut pressure readings are collected using the data-loggers on the trucks as well as the truck velocity associated with each reading. Rack, roll and pitch are the main key performance indicators (KPIs) that are calculated to study the adverse effect of an unbalanced payload and consequently the truck structure. Finally, the shovel bucket load passes within the truck body are simulated and a new method is suggested to improve the truck payload balance.

Aug 1, 2013

By P. Nayak

"Comminution is an energy intensive and expensive process consuming approximately 40-50% of the total processing costs in a mining operation. This process poses an even greater challenge with gold ores due to their low elemental concentration and small particle size. Over 99.9% of the ore fed to the mill is waste which must be removed during the ore processing stage. Preconcentrating the Run of Mine (ROM) ore before feeding the mill will result in significant cost savings. In partnership with Sacré-Davey Engineering, Agnico Eagle Mines Limited identified this opportunity and is currently evaluating the implementation of sorting technology to preconcentrate the ore or upgrade the waste material at its operations. This paper will discuss the steps adopted by Agnico Eagle in the evaluation and installation of sorting technology at its operations. Since the Company has a large portfolio of operations, the first step in the project was to shortlist the operations that had the highest probability for successful application of the technology. Following this, the top three operations were selected for bench scale evaluation. The projects which showed the most economic potential were then considered for detailed evaluation and pilot plant installations. This paper provides an insight into the methodology followed by Agnico Eagle and Sacré-Davey in the evaluation of the technology.INTRODUCTION The benefits of ore sorting technology are being increasingly understood by the mining industry today. The application of ore sorting in gold mining is attractive due to the nature of the mineral distribution. The presence of high value minerals distributed in an extremely small mass of the ROM ore creates a tremendous opportunity for preconcentration with ore sorting. Since Agnico Eagle currently has a portfolio of eight operating mines and numerous development projects and exploration properties, the challenge was to identify the deposits which had the most favourable mineralogy and grade distribution for successful ore sorting. The success of ore sorting is mostly based on the minerals present in the deposit and the grade distribution. The minerals signify the amenability of the deposit for ore sorting and the kind of sensing technology to be used. On the other hand, the grade distribution demonstrates the amount of material that can be rejected without losing value. In order to understand a deposit’s characteristics, it is important to examine the sample’s behaviour with various sensors and then assay it to know its actual value. It is a common practice in the mining industry to document assay value of drill cores and/or material feeding in and out of the mill. However, those VALUES (are insufficient to understand the grade variability on a granular basis. To capture the ore variability in very high resolution and significantly improve the selectivity of the material feeding the mill, it is vital to assay the samples on a rock-by-rock basis, as this is the level of resolution which will be examined by the ore sorter during sorting. A careful and elaborate procedure was followed in evaluating the technology at Agnico Eagle’s operations which is discussed in this paper."

Jan 1, 2019

By K. Meshinchi Asl

In this study the effects of T4 and T6 heat treatments on microstructural characteristics of AZ91 alloy containing Rare Earth elements have been investigated. Formation of intermetallic Al1 1RE3 needle shape particles which have a good thermal stability reduces both formation of ß(Mg17A112) and discontinues precipitation in AZ91 alloy which are dominated at the grain boundaries and are responsible for poor mechanical properties specially in elevated temperatures. For AZ91-RE samples both T4 and T6 heat treatments led to a continuous precipitation of ß particles at the grain boundaries after aging. However, in AZ91 samples (with no Rare Earths) precipitation was discontinuous at grain boundary areas. This type of precipitation is one of the main reasons of poor mechanical properties of this alloy at elevated temperatures.

Jan 1, 2007

By Derek E. McBride

"Exploration work in the Beardmore - Tashota area has led to a reinterpretation of relationships between gold mineralization and the geologicalevolution ofthe area. The host volcanic rocks form two parallel volcanic belts connected by a much smaller cross-cutting band, which trends northeast from Beardmore to Tashota. This connecting band consists of mafic and felsic volcanic, plus clastic sedimentary rocks in a sequence conformable with the contact of the Onaman Lake Batholith to the east. A metamorphic aureole or incorporated xenoliths are lacking along this major contact and the only intrusive relationship observed is chilling between mafic dikes and a cold host granite in proximity to it. Granite dikes are totally lacking in the volcanic succession, or the overlying sedimentary sequence. A major part of this sequence consists of a polymict basal conglomerate with granite boulders and volcanic clasts in a fine-grained chloritic matrix. The nearest source for these boulders is the Onaman Lake batholith.Gold mineralization in significant economic quantities (+ 50 000 ounces) occurs at the top or above the mafic volcanic succession as quartz bands. In the Northern Empire Mine, the band is conformable, folded, boudinaged and the mineral zoning shows a relationship to variations in the host rock, not structural overprinting. In general, where the host mafic tuff is medium-grained, the quartz band is thicker, up to a metre wide, and carries economic grade; where the tuff is finer-grained and bedded, the band is very thin and low grade.Stratigraphic control and metal zoning shows that the mineralization formed as part of the development of the volcano- sedimentary succession. The other major deposits in the area (Leitch and Sturgeon River) have a similar structural history suggesting that they are also syngenetic in terms of the stratigraphic development. Regionally, these deposits were emplaced prior to any significant tectonic deformation but at the end of the mafic volcanic event.The mafic activity was related 10 a period ofextension which caused the volcanic troughs to develop along centres of rifting. The hiatus at the end of this event permitted extensive hydrothermal systems to form and deposit siliceous exhalite bands within sedimentary or terminal mafic volcanic environments in promixity to major thermal sources. Subsequently, the Kenoran Orogeny deformed the entire succession into upright folds with a sub-vertical schistosity. Evidence shows that the deposits have remained intact since deposition."

Jan 1, 1987

By John B. Riddell

"AN EXCELLENT review of the status of applied geochemistry was given by Warren (1959) at last year's General Meeting of the C.I.M. The purpose of this paper is to present recent developments and trends. Several important books were announced during 1958: Ginzburg, I. I. Principles of geo-chemical prospecting. (In process of translation from the Russian by V. Sokoloff).Vinogradov, A. P. The geochemistry of rare and zvidely scattered chemical elements in soils. Consultants Bureau, N.Y. Korzhinskii, D. S. Physicochemical basis of the analysis of the paragenesis of minerals. Consultants Bureau, N.Y.In addition to these translations Mason's Geochemistry' has been revised, and Hawkes and Webb (personal communication) are publishing a book on geochemical exploration. A Symposium on Geochemistry was head in Paris in July, 1957, in conjunction with the XVIth International Congress of Pure and Al-lied Geochemistry. The abstracts of the papers presented at this Symposium were published in Geochimica et Cosmocl1imica Acta, 1958, Vol. 14, pp. 150-167."

Jan 1, 1960

By J. A. C. Fortescue

During the past decade, geochemical prospecting methods have become important in Canadian mineral exploration. The object of this paper is to discuss the role of geochemical methods in a typical mineral exploration program involving parallel geological and geophysical methods applied at different degrees of intensity. Particular attention is given to the description of the degree of development of geochemical prospecting under different kinds of local conditions.

Jan 1, 1967

By Yanping Xiao, Ton van Sandwijk, Gus Van Weert, Larry McHugh, Thomas Zabev

"All attempts to remove significant amounts of arsenic from enargite via neutral or reductive pyro routes have required operating temperatures between 600 and 700 º C, too high to propose an equipment development program. Operating at reduced pressures, or using hydrogen or elemental sulphur as a sweeping gas did not help to lower these temperatures. Admixing iron powder gave excellent results, but still required 700 º C. By fortuity, in recent experiments to produce tennantite from an enargite mineral sample, it was observed that enargite was completely converted to bornite, chalcopyrite with minor residual tennantite within an hour at 400-450 ºC. This is believed to be due to the presence of pyrite in the mineral sample treated. All earlier decomposition work appears to have been done on predominantly enargite (i.e. low pyrite) samples, or at high operating temperatures, ignoring possible reactions at lower temperature. The decomposition of enargite into iron substituted tennantite plus some bornite under evolution of liquid elemental sulphur, followed by further decomposition of this tennantite into bornite and volatile arsenic sulphides, appears experimentally feasible at these low temperatures and mimics described ore genesis pathways at > 250 ºC in saline solutions. We suggest two pathways to describe the observed experimental results:20 Cu3AsS4 + 12 FeS2 ???5 Cu10Fe2As4S13 + 2 Cu5FeS4 + 31 S(l)31 S(l) ???31 S(g) (evaporation)5 Cu10Fe2As4S13 ???10 Cu5FeS4 + 10 AsS(g) + 5 As2S3(g)"

Jan 1, 2014

By M. C. Harris

"Excess Gibbs energy is a thermodynamic parameter which quantifies the difference between the value of the Gibbs energy for a real mixture and that for an ideal mixture. More specifically the partial molar excess Gibbs energy of a species (i) in a mixture is indicated by the change in the overall excess Gibbs energy of the solution as the number of moles of species (i) changes while keeping temperature, pressure and the number of moles of all other species in the solution constant. Generally it is obtained from the activity coefficient which in turn can be obtained for a species in a mixture using a variety of models. The most widely used method is to use UNIFAC. Flotation is probably the most important process in the concentration of minerals and requires the use of reagents such as collectors and frothers. There is abundant experimental data which illustrates that collectors of different alkyl chain lengths will change the contact angle and that frothers of different structures and molecular weights will result in changes in key flotation properties such as froth behavior, surface tension and critical coalescence concentration. In this paper it is shown that there is a strong linear relationship between measured parameters such as froth volume/height, surface tension, critical coalescence concentration and contact angle and the partial molar excess Gibbs energy of the molecules used. Proposals are made to explain these correlations.INTRODUCTIONAs is well known froth flotation is arguably the most widely used process in the separation of minerals. In broad terms the process relies on the use of reagents known as collectors to adsorb onto a mineral surface and thus render the mineral particle hydrophobic. Alkyl thiolates are very commonly used for this purpose. The hydrophobicity is induced as a result of the alkyl group’s molecular structural properties which results in it forming a non-ideal mixture with the process water. Surfactants (or frothers) are typically alcohols and are known to lower the surface tension of the system and also inhibit bubble coalescence and reduce bubble size. Since alcohols are polar they will also form a non-ideal mixture with water. The hydrophobic mineral attaches to the bubble and rises to the froth phase where the valuable mineral is recovered as a concentrate. Frothers have often been characterized using the so-called HLB (hydrophobic-lipophilic balance) number but recently it was shown that the use of activity coefficients (?) or excess Gibbs energy (G ex ), which is calculated using equation (1) is a much more appropriate way to describe the behavior of these reagents in non-ideal mixtures with water (Corin and O’Connor, 2014)."

Jan 1, 2016

By M. A. Nagle

Various strategic projects were carried out in 2002 to increase the capacity of Teck Cominco's integrated zinc-lead smelter at the Trail operations site in British Columbia, Canada. The lead smelter treats the iron residue from the zinc plant and optimizes the overall zinc recovery. This paper summarizes two options that were considered to reduce the zinc content in the leaching iron residue. The first option involved increasing the capacity of an existing hot acid leach circuit up to the iron loading constraints of the circuit. The second sought to maximize the hot acid leach capability by separating the ferrite-rich solids, followed by aggressive hot acid leaching (>100°C) and subsequent iron precipitation. Different forms of iron precipitation were reviewed in order to determine the most effective and economical approach. Among these, was a novel high temperature ferrite conversion process. The technical results and selection criteria are presented together with possible ways to integrate the process concepts into the current sulphide leaching plant circuit. The first option was selected for implementation and is currently being operated successfully.

Jan 1, 2006