Search Documents

By D. Doyle, T. Cienski

"This paper presents and discusses the results of a detailed study conducted on the subject of energy consumption in the comminution of industrial minerals. The study was based on pilot circuit testing, plant operating data collection, detailed equipment data and literature research. The areas covered by investigations include: high efficiency classification; air classifiers for cement grinding circuits; grinding aids in dry grinding; and dry grinding circuit control based on particle size measurement. Results obtained indicate a large potential for the reduction of energy consumption, in particular in the cement clinker grinding circuits. Better classification techniques and correct application of grinding additives can significantly reduce power used per tonne of product and also substantially increase grinding circuit output."

Jan 1, 1992

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012

By M. J. Scoble, H. L. Francis, D. F. Salter, G. R. Baiden

Intelligent ore delineation refers to the ability reliably to characterize the geological setting of a mineralized body and its grade distribution. This necessitates using all available geological information in a timely and efficient manner, such that effective geological control is achieved. The importance of geological control is paramount to improving the efficiency and competitiveness of underground mines. As a result, the development of new geosensing tools designed to provide more reliable and timely information should be a priority. However, as the sensing tools advance then so, too, must the decision support system in order to allow the full benefits of these tools to be achieved. One potential system considered able to provide this architecture is ’true 3D-GIS’ (Geographical Information System). GIS promises to provide a seamless data flow and to connect information currently unavailable to the underground mine operations by bringing together previously disparate and spatial data sets in a visually effective and timely way. This paper considers the potential revolution GIS offers over the flow and use of data in mining by focusing on the integration of geosensing data and GIS to facilitate intelligent ore delineation.

Jan 1, 2000

By M. Potesser

Higher prices for natural gas or oil have motivated the copper industry to reexamine the modes of oxygen and oxy-fuel burner usage at operating plants. With rising energy costs and the growing importance of environmental protection, burner usage and burner operations have become the focus of several investigations and optimization efforts. One possible approach to lower energy usage is through combustion using tonnage oxygen. When such oxygen is used, the flame temperature increases and operational efficiency is improved. As well, with the correct technology, due to the presence of lower levels of harmful substances such as NOx in the off gas, there is improved environmental performance. As regards copper production, furnaces are employed for both concentrate smelting or for melting and casting operations. The use of tonnage oxygen in concentrate burners for smelting provides for a higher thermal efficiency. For furnaces employed for melting, air-operated burners may in fact have an initial advantage because a long radiant flame is typically generated, thus providing for a higher degree of heat transmission. This paper describes the new experimental burner chamber of Messer Austria GmbH which provides for testing of the combustion of natural gas with oxygen or oxygen-enriched air and the use of special water cooling ducts that simulates a metal charge during melting, The operational effectiveness of the burner is determined from temperature and off-gas analysis data. The paper also discusses future trends in burner technologies including a new patented burner. Cu2007 - Volume III (Book 2) The Carlos Diaz Symposium ou Pyrometallurgy Edited by A.E.M. Warner, C.J. Newman, A. Vahed, D.B. George, P.J. Mackey, A. Warczok Toronto, Canada,

Jan 1, 2007

By Earl T. Hayes

This paper briefly reviews the laws enacted in the United States governing the coal miner. It discusses amendments to the Coal Mine Safety Act and describes the provisions of the Metal and Non-Metallic Mine Safety Act.

Jan 1, 1969

By M. Maccagni, J. Nielsen

"The recovery of lead from battery paste has been investigated for a long time and with the use of many different electrolytes. A number of processes have been presented, but none of them reached even the demonstration step. Engitec has developed a new concept for the battery paste electrowinning using a chloride electrolyte fed through a very innovative flow cell. The process has passed the lab and the demo scale and it is ready to be introduced on the market. In this paper, a description of the process will be provided.INTRODUCTIONThe need for improved energy storage systems as well as the introduction of commercially viable electric vehicles is providing a strong compulsion toward the research of new batteries. The lead battery is playing an important role because it is inexpensive, reliable and it is the most recycled material. This last aspect marks the lead acid battery as quite peculiar making it both the primary lead based product and the main raw material for lead production.In the last years the legislative pressure has become very strong and has forced the lead production to react through the introduction of important process innovations and market changes. The dispersive products, such as additives for paints and for fuel as well as bullets, have been practically banned all over the world while the battery market continues to grow. The lead acid battery remains the cheapest and most integrated energy storage system available and is improving to meet the new technical challenges. This is testified by the news coming from the development of new and more efficient lead acid batteries which are confirming their leading position.Unfortunately, the image of lead is very negative in the public opinion and some important actions are required to try changing this sentiment. Among them, better information to the market and users and the introduction of new and cleaner technologies in the production of lead can help."

Jan 1, 2016

By T. W. Wlodek

"AbstractIn this paper a new type of durable 'spiral-rolled' drill set is introduced and its performance discussed. Efficient and economical mine drilling-depends to a great extent on durability of the drill-set employed. Premature failure of this element damages the drill bit and is costly when tungsten carbide bits are used.Time of drilling of 'spiral-rolled' drill sets introduced at present in Canada is considerably larger than for the presently used drill steel, but laboratory simulated service tests and practical field tests show that the 'drilling life' of the spiral-rolled drill set is several times that of ordinary drill steel.Some features of differential plastic deformation and differential surface rolling, so called 'spiral-rolling', are given.Relations between the drilling machine drill set and characteristics of the ore are discussed. The effect of shims on conical drill rod attachments, the mechanism of failure of drill steel, .and stresses during mine drilling, are analysed.IntroductionIN MINE DRILLING operations, the main interests are: the drilling machines as a source of working energy, the drill set as the tool transferring the working energy to the cutting edges of the bit, and, finally, the drilling characteristic of the .ore or waste rock.This paper includes a review of the possibilities of metallurgical and mechanical improvements in the drill set, with particular attention to drill steel and the attachments.For economical and efficient mine drilling operations, a durable drill rod, attachment, and drill bit are essential. Premature failure of any of these parts interferes with mining operations and is costly."

Jan 1, 1955

By P. V. Golde, R. A. Poole, G. R. Baiden

"The results being presented in this paper are those obtained during 1996 on a drilling automation project at Stobie mine. This project has successfully demonstrated that the remote operation of multiple drills (by a single driller) from surface using Tamrock Data Solo 1000 Sixty drillrigs is technically feasible and can potentially bring significant rewards in terms of productivity and work environment improvements, as well as labour and maintenance savings. BackgroundThe ObjectiveThis paper is an update of a previous report on remote drilling research at Stobie mine. Enabled by the communications system installed at the mine, the ability to remotely control underground equipment from surface has been demonstrated (Poole et al., 1996). This paper discusses the needs and process required to carry this concept to consolidate the operation of multiple machines under a single operator.The TeamThe team assembled to develop and implement the automation and the communi-cations extensions needed to allow the multiple machines’ operation from the surface by one operator included the following:INCO Mines Research supplied the project management and original project initiative. The primary purpose was to prove the advantages of savings associated with the driller not being required to travel to the underground drill location coupled with the savings associated with one-man, multiple-machine techniques.Tamrock EJC supplied the Data Solo 1000 Sixty drills and the Tamrock specific machine-based custom software. The drills were produced in Finland with no provision for remote operation of the drill from other than the umbilical attached local console.Automated Mining Systems supplied the modifications to the drill communications equipment to allow the machine communications to become broadband compatible. As well, Automated Mining Systems also supplied the hardware necessary to be able to remotely control the portable video camera, as well as the data logging equipment.Stobie Mine personnel were made available to test the function and then integrate the concept of remote control drilling into the Stobie operations."

Jan 1, 1997

By C. J. Brown

Regeneration of hydrochloric acid steel pickle liquors has traditionally been accomplished by pyrohydrolysis. However, a number of factors have recently conspired to reduce the attractiveness of this approach. Moreover, the process is not amenable to small-scale operations. On the other hand, the standard technique for regeneration of sulfuric acid pickle liquors, which is the low-temperature crystallization of ferrous sulfate is applicable to any size operation. A similar technique has recently been developed to regenerate hydrochloric acid. Sulfuric acid is added to the ferrous chloride-bearing spent HCl pickle liquor. The temperature is then reduced to below 0°C, resulting in the crystallization of ferrous sulfate heptahydrate and liberation of free hydrochloric acid. Depending upon the crystallization temperature, variable concentrations of sulfate are left in the regenerated acid. Although this residual sulfate has an impact on the pickling characteristics of the regenerated acid, tests have shown that by adjusting the conditions, pickling rates will be at least equal to those using pure HCI, and an acceptable surface finish will be produced.

Jan 1, 2006

By L. Rao, P. Carabin

"Advances in thermal plasma torches have resulted in this technology becoming a commercially viable solution for chemical and metallurgical processes. The main advantages of plasma are its ability to control process chemistry and to build small footprint reactors due to its high energy density and reactivity of the free radicals that are produced. This paper focuses on thermal plasmas produced by DC torches and their applications for waste treatment, production of high purity metals, and nanomaterials. Both transferred and non-transferred torches have been used as either a source of heat or as a reagent in various industrial processes. INTRODUCTIONPlasma technology has become an ideal solution for many industrial chemical, metallurgical and mechanical processes (Venkataramani, 2002). Thermal plasma powered systems are typical used for their unique characteristics such as high energy densities, high temperatures, small installation sizes, rapid startup and shutdown features, controlled process chemistry and use of electrical energy as a heating source resulting in decoupling the heat source from the oxygen flow rate (Heberlein et al., 2007). Depending on the nature of the main plasma forming gas used, thermal plasma systems offer a high temperature heating source coupled with a highly reactive plasma plume rich in free radicals and ions which promote otherwise hard to drive chemical reactions, as well as high heat transfer rates.Industrial plasmas can be broadly classified as thermal plasmas and non thermal plasmas. Thermal plasmas are atmospheric pressure plasmas characterized by local thermodynamic equilibrium (Boulos et al., 1994). Thermal plasmas are typically established between any two current conducting electrodes separated by an insulator. A plasma forming gas is blown between the two conducting electrodes resulting in a high temperature plasma plume. A plasma torch generates and maintains an electrically conducting gas column between the two electrodes; a cathode (negative electrode) and an anode (positive electrode) (Camacho, 1988). If both electrodes are housed in a single housing, resulting in an arc enclosed inside the plasma torch, then such plasma generating torches are termed as non-transferred (NT) plasma torches, whereas, if the second electrode is external to the torch, creating an arc transferred between the cathode and the working piece, then such plasma torches are termed as transferred (T) plasma torches. Depending on the source of the electricity which can be either direct current (DC), alternating current (AC) at main network frequency or at radio frequency (RF), the plasma torches are classified as DC, AC or RF plasma torches (Venkataramani, 2002)."

Jan 1, 2012

By Dan Currie, Tom Lamb, J. Coady Marsh, Gary Landry

"This paper describes the Cape Breton Development Corporation's experience with the Lovat M-300 tunnel-boring machine at the Donkin-Morien Mine. Between January 3 and December 21, 1984, the 7.6 m (25 It) diameter TBM advanced 3350 m (10 990 ft) . The authors will describe experiences with the machine and highlight the implications of tunnelling machines to underground coal mine development in Canada. IntroductionThe Cape Breton Development Corporation (CBDC) has recently completed the drivage of a 7.6 m (25 ft) diameter tunnel, 3.5 km (2.2 miles) in length , to access the Harbour Coal Seam at the Donkin-Morien Project. The tunnel was successfully driven with the first Canadian rock tunnel-boring machine (RTBM or TBM), designed and built by Lovat Tunnel Equipment, Inc. The initial mine development consists of the drivage of two tunnels to the first major coal seam. Future plans are proposed for the development of a 4 million tonne-per-year mine (Marsh et al., 1983, Gillman, 1982), which will require the drivage of a further two tunnels and could access up to four coal seams. The tunnel cross-sectional areas were designed to provide sufficient ventilation area and access for a production of 4 million tonnes per year."

Jan 1, 1986

By P. C. Patnaik

Performance of industrial gas turbine engines in terms of power output, reduced cooling and efficiency have been continuously increasing in parallel with aero gas turbines due to the advances made in the development of new materials, protective thermal barrier coatings (TBCs) and the advanced diagnostics to monitor service induced problems such as hot corrosion, thermal and thermo-mechanical fatigue and other operational issues, Environmental attack (hot corrosion or high temperature oxidation) is a common degradation mode in the hot section of the gas turbine, Hot corrosion occurs when Na or K bearing compounds in the environment or in the fuel combine with other contaminants such as S and Pb or V to form corrosive sulphates or vanadates thus attacking the protective oxide on the turbine airfoil, These problems pose far more threat to new turbine engine materials such as directional solidified, single crystals and ceramic matrix composites (CMCs). The CMCs due to their increased temperature capability, when used in the combustion chamber, are likely to reduce the peak temperatures attained during combustion and therefore provide the benefits of reduced emissions of oxides of C and N, These issues will be reviewed critically and their impact will be assessed on gas turbine lives. With respect to alternate fuels, past experience has shown that utilization of residual oils and coal derived fuels in gas turbines have resulted in complex deposition and corrosion processes, In recent years biomass derived alternate fuels have been used either through a gasification cycle or through direct firing of the biomass derived liquid fuel with a view to reduce Green House Gases (GHGs) and improve the climatic conditions. In both cases, the resulting high temperature corrosion processes (in the presence of alkaloids in the fuel) are also very complex, leading to premature removal of hot section components, Technology solutions mitigating these fundamental problems will be reviewed and solutions presented.

Jan 1, 2005

By Lisa L. Van Loon, Neil R. Banerjee

Canada is a world leader in uranium exploration, but many deposits are located in remote regions making exploration targeting challenging. Novel approaches are needed to detect the presence of large-scale ore-forming systems and to vector toward mineralization. Boron is commonly used as a key pathfinder element associated with sandstone/unconformity-hosted and basement-hosted uranium deposits in the Athabasca Basin, but the genetic relationship remains uncertain. Alteration assemblages containing boron geochemical anomalies are commonly spatially-associated with – and possibly coeval with – uranium mineralization. Boron is commonly found in tourmaline minerals but in some portions of ore deposits the host mineral for the anomalous boron remains cryptic. Boron coordination chemistry within alteration haloes can better constrain boron host mineralogy, provide insight into the nature of the boron-uranium relationship, and thus has the potential to better constrain targets for exploration. Synchrotron-source X-ray absorption near-edge structure (XANES) spectroscopy is a direct, element-specific analysis that identifies boron coordinated in both trigonally- (BO3) and tetrahedrally-coordinated (BO4) forms. This makes XANES uniquely suited for identifying the geochemical hosts for boron that may be related to hydrothermal ore forming processes. XANES spectroscopy was conducted on whole-rock assay powders from uranium deposits across the Athabasca basin containing boron concentrations ranging from <10 ppm to >10,000 ppm. XANES directly identifies the relative amount of trigonally- (BO3) and tetrahedrally-coordinated (BO4) boron in these complex mineralogical mixtures. Our work suggests a link between boron and uranium that is likely related to the unique physiochemical characteristics of ore bearing fluids that may provide a unique vector to mineralization.

Jan 1, 2020

By T. F. Pugsley, D. Gignac

"The historical background to the project dates back to the mid-30s with the discovery of surface sulphide showings in the Cape Smith-Wakeham Bay ultramafic belt. In the mid1950s, orderly exploration commenced with an extensive work program by Asarco, INCO, Lemoine, Falconbridge and Raglan Nickel Mines Ltd. on exploration permits. In 1966, Falconbridge and Raglan Nickel Mines interests merged. Extensive exploration, drilling, under- ground delineation of the Donaldson orebody and the construction of basic infrastructure such as camps, airfield, road links from Douglas Harbour to Donaldson and Katinniq, a distance of 60 km, were completed.Production project design at that time consisted of plans for a 50 000 mt per year nickel mining and concentrating operation, including a 2000 person community and smelter at Douglas Harbour. These plans unravelled in the mid-70s due to high capital costs, poor nickel market conditions and the realization that the Raglan orebodies were not large enough to economically support the construction of green field smelter and refinery facilities for processing Raglan production. Nickel market conditions in the late 70s and early 80swere generally poor, resulting in further delays on production plans.While recognizing the very high potential to discover increased tonnages of high grade(3% Ni) in excess of 20 million tonnes, the project was deferred into the late 80s when a serious re-evaluation of exploration potential occurred and the requirement to prove up additional reserves resulted in an underground exploration program at Katinniq covering the period 1990-1992."

Jan 1, 1996

By G. Granata, C. Tokoro, T. Kato

"The goal of this study was to evaluate the effectiveness of mechanochemical activation by planetary milling as method to enhance the recovery of cerium from rare earth ores. For this purpose, a weathered ore was first ground by planetary milling and then leached by sulfuric acid. The influence of planetary milling was investigated by assisting the experiments with X-ray absorption fine structure (XAFS) in cerium LIII-edge and inductively coupled plasma spectrometry to measure the concentration of cerium dissolved by leaching. Results showed that, by increasing the grinding time, although the particle size of the specimen increased due to agglomeration, the recovery of cerium significantly increased. This finding clearly indicated that a smaller particle size actually hinders the recovery of cerium. In particular, XAFS analysis revealed that the longer the grinding time, the more tetravalent cerium could be converted into trivalent cerium and such conversion, also called mechanochemical reaction was beneficial to the recovery of cerium. Based on the obtained results, it was confirmed that approximately 70% of cerium could be recovered by mechanochemically activated leaching of rare earth ores.INTRODUCTION Rare earth elements (REEs) are a group of 17 chemically similar metallic elements comprising lanthanides, scandium and yttrium. Since REEs have various unique physical and/or chemical properties, they have become essential materials for advanced application (Adachi, 2015). REEs used in industry are usually supplied as rare earth minerals. In the last decades, flotation, gravity separation, magnetic separation and leaching have been widely applied to recovery of REEs from rare earth minerals like monazite (Archana, Rekha, Manis, Jitendra, & Jin, 2015). Among these operations, leaching has been widely studied in the recent years to improve the state of the art (Archana, Rekha, Manis, Jitendra, & Jin, 2015; Xiao, Feng, Huang, Huang, Chen, Liu, Wang, & Long, 2016; Farzaneh, Fereshteh, & Ahmad, 2017). Aiming to enhance recovery of REEs from rare earth minerals, a possible advancement of leaching technology could be the mechanochemically activation of the ore by high-intensity milling (Alorro, 2016). In the mechanochemical activation, an improvement of the leaching performances can be achieved through high-intensity milling operations which result into a dramatic decrease of the mineral particle size with a consequent improvement of the physical kinetics of leaching. Furthermore, the high mechanical energy provided to the sample during milling can determine the rupture of the crystal structure of the mineral, thereby transforming it into a more leachable form."

Jan 1, 2017

By L. M. Lowe, D. B. Chambers, D. G. Feasby

"Potentially economic deposits of rare earth elements (REE) often contain elevated levels of naturally occurring radioactive materials (NORM), primarily thorium and uranium and their associated radioactive decay products. The concentrations of NORM usually exceed typical background levels of natural radioactivity, sometimes by factors of ten or more, and can be of concern relative to occupational radiation protection and the management and disposal of REE mineral processing and metallurgical wastes. This paper provides a summary of the radiological issues normally encountered in the REE concentrate production industry. In addition to an introduction to background radiation and radioactivity, including the thorium and uranium radioactive decay series, radiation levels expected to be encountered in REE concentrate production are outlined. The occupational, environmental and regulatory aspects of REE production related to NORM, including radiation dose limits, radioactive waste disposal guidelines, and threshold VALUES (for the application of transport regulations, are presented.INTRODUCTIONConcurrent with the increasing demand for new sources of rare earth elements (REE) to meet modern industrial needs, there is also an increasing awareness of the radioactivity associated with the REE ores and resources. This is an especially important consideration in addressing questions from the public and local communities who are often concerned about “radiation” and “radioactivity”. Public concern is heightened by reference to legacy issues that arose during times of less regulatory oversight; as well, the benefits of modern technologies, practices and regulation are overlooked. Such concerns are also often inflamed by unfounded claims by non-governmental organizations (NGO’s). Thus, it is important that all concerned have a full understanding of just what the potential risks from radiation associated with REE are, or are not. This paper provides an overview of the sources of radioactivity, the potential implications of radiation and radioactivity in the REE industry, and a brief discussion of established and reliable methods of managing exposure to radiation and radioactivity."

Jan 1, 2012

By Melvin S. Taylor

The environmental control program at Cassiar Mine is an active one involving government, unions and company personnel all working together to achieve a goal- "A clean and safe working environment". This can only be achieved by utilizing three of Cassiar&apos;s most important resources; i.e., people, time and money. Past environmental programs have more than proved that the goal can be reached and. with the future programs now in progress. Cassiar Asbestos will achieve its environmental goals.

Jan 1, 1978

By J. C. Rudolph

"THE TOPIC on which I am speaking this afternoon is ""The Future of the Canadian Oil Industry.'' At the time of C + 100, we should take a searching look at ourselves, an honest appraisal of our achievements and a forthright accounting of our shortcomings as well as the uniquely Canadian aspects of this industry. I would like to put before you some of my views on the direction we are taking in the exploration field and in the production field. I would also like to speak briefly on some of our problems and the role of the various segments of our industry in solving these problems.First of all, let us look at the exploration picture. We are in the midst of an exploration boom. There were 133 seismic crews active in Western Canada this winter, the highest since 1957, land prices are appreciating rapidly, Canadian oil reserves increased + 16 per cent during 1966, there is a great demand for technical personnel of every kind and the whole industry, except the drilling segment, seems to be prospering. This surge of activity has its roots in two major occurrences. The first of these was the change in the pro-ration system in Alberta, the major producing province, accompanied by the change in spacing pat-terns. The proration change was designed primarily to encourage in-creased exploration and it has certainly had this effect. It has also had the unforeseen effect of put-ting everyone into what we, in the oil business, call ""elephant hunting."" In other words, the days of the development of barely economic, marginal fields are over. Oil companies today are only interested in high-reserve, high-productivity, high-quality reservoirs."

Jan 1, 1968

By Corby G. Anderson, Caelen D. Anderson, Patrick R. Taylor

"The United States contains a variety of domestic rare earth element mineral sources containing such as ancylite, bastnasite, monazite, and xenotime. Research has been performed to investigate the fundamental surface chemistry involved in the froth flotation of these minerals, and apply the knowledge gained to substantiate the results through experimental testwork on a domestically sourced rare earth ore. This paper will outline the fundamentals and literature of rare earth mineral flotation, review its industrial applications and provide some recent research updates.THE RARE EARTH ELEMENTSRare earth elements (REE’s) are a unique family of elements with nearly identical physical and chemical properties. They account for approximately 1/6th of all naturally occurring elements, but the entire group occupies only one position on the periodic table. These 15 elements make up the lanthanide series (atomic numbers 57–71), and all but one (promethium) occur naturally. In addition to these 15 elements, yttrium and scandium are also considered rare earths since they tend to occur in the same deposits as the rare earths and share similar physical and chemical properties as seen in Figure 1. In particular Figure 2 denotes, a cartoon of the subtle differences in each caused by the 4f atomic sub shell (Gschneidner Jr., 1964). These subtle differences result in very difficult challenges in the selective concentration and final separation of each rare earth. (Anderson, 2015, Kronholm, Anderson, Taylor, 2013)Rare earths are separated into two different subsections; the “lights” or LREE’s (lanthanum57 through europium63) and the “heavies” or HREE’s (gadolinium64 through lutetium71). Yttrium is generally considered a heavy rare earth since its ionic radius is close to that of the HREE’s, while scandium is not considered either a light or a heavy."

Jan 1, 2016

By H. C. Gunnings, C. O. Swanson

"The Sullivan mine; at Kimberley in southeastern British Columbia; is the largest silver-lead-zinc mine in the Empire and one of the largest in the world.The original discovery was made in 1892 by four prospectors. Until 1899, when the branch line of the Canadian Pacific railway from Cranbrook to Kimberley was completed, little work was done on the property. In 1900, systematic development was started, and during the next 3 years 5,000 tons of ore was shipped to the smelters at Nelson and Trail. By 1903, some 300,000 tons of ore was developed, and a smelter was started at Marysville, about 5 miles from the mine. However, this smelter closed down in 1907 because of metallurgical difficulties after treating 75,000 tons, and the property came under the control of the American Smelting and Refining Company. An option on the property was taken in 1909 by the Consolidated Mining and Smelting Company of Canada, who exercised their option in the following year. During the next 5 years by selective mining and sorting 188,000 tons of high-grade ore was produced and shipped to Trail. This tonnage came from the upper levels, about 4,600 to 4,800 feet in elevation. At the same time, deep drilling down to the 3,900-foot level showed the presence of an immense body of complex ore. In 1915, the main adit-the 3,900-foot level-was started, and by 1919 this had been driven a distance of 2 miles to develop the ore above this level. Meanwhile, progress was being made in overcoming the milling problems. An interesting account of this work was written by the staff ( 4). In 1923, the first unit of the present concentrator was erected, with a capacity of 2,500 tons a day, and thereafter the rate of production increased rapidly. In 1934 it was around 8,000 tons a day, and to date a total of about 30,000,000 tons of ore has been sent to the mill. In recent years, a considerable part of the production has come from levels between the 3,900-and 3,350-foot, which were opened by an internal incline shaft started in, 1930. In 1942, tin was added to the products separated at the concentrator."

Jan 1, 1954