Search Documents

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By Barry Hope, Javier Rico

"Goldcorp’s Hoyle Pond mine has recently completed several projects which have impacted the overall ventilation system. The project includes extending the Fresh Air Raise (FAR) to depth, development of a new Return Air Raise (RAR), and the installation of new sensors and ventilation controls throughout the mine. Two years after the completion of #2 Winze, the mine is ramping up its ore production to 1,300 tpd (up from 1,100). To ensure safe and profitable production, a reliance upon technology has been needed to provide the required ventilation to the work areas according to the mine plan. To systematically assess the mine’s ventilation in real-time, a significant increase in remote monitoring was required. This included installing additional flow, pressure, temperature and gas sensors. The first step in upgrading the existing monitoring was to purchase airflow and differential pressure monitors and install them in key areas of the mine. This paper presents the process of expanding the monitoring capability at Hoyle Pond mine, the selected equipment and the results of the implementation. The intended goal was to improve safety while minimizing capital and operation costs. The monitors were installed in strategic locations to provide immediate feedback on the impact of changes to the primary ventilation airflows. Comparing the available sensor technologies, installing them and systematically monitoring the ventilation served as a first step towards developing a mine wide Ventilation Control System. In addition, the initial state of the monitoring and control system, with final results and the chosen solution for the mine site, are presented. INTRODUCTION The Hoyle Pond mine is located in the City of Timmins, within the Porcupine mining district, Ontario, which has produced more than 70 million ounces of gold since 1910. Currently, approximately 60% of Porcupine Gold Mines gold production comes from the Hoyle Pond underground mine. Mechanized cut and fill and long-hole mining methods are used to extract the ore. The remainder of the ore comes from the Hollinger Open Pit mine. The Dome Underground mine ceased operations in 2017. Hoyle Pond is currently mining at 1820 meters below the surface and plans to go deeper. The average dry-bulb as wet-bulb temperature underground varies according to the depth and surface conditions which has extremes of –40°C in winter to +30°C in summer. The total airflow volume pushed down from surface is 240 m3/s to accommodate the diesel-powered equipment needed for normal operations. In order to improve the quality of air underground a program has been implemented to use diesel particulate filters, starting with the truck fleet and 6-yard scoops, followed by the intention to implement the rest of the functional diesel-powered equipment and eventually move to electric equipment."

Jan 1, 2019

By A. Golpaygan

Application of Computational Fluid Dynamics (CFD) modeling for simulation of fluid flow and combustion in industrial scale electric furnace is presented. Poor combustion efficiency, roof and/or side wall overheating, carry over to off-gas system and non-ideal radiative heat transfer to processes or cooling systems have been common limiting factors causing inadequate process performance of the furnace, operational problems, and safety hazards. This paper describes how CFD analysis can be used to obtain a better understanding of commonly observed problems associated with freeboard combustion. Examples are presented to describe using combustion CFD modeling to understand requirements to diagnose a problem with furnace design including required freeboard volume or possible roof/side wall overheating.

Jan 1, 2011

By A. Taylor, E. Thorn Corthay, R. Storey

In response to requests from its stakeholders, the International Standards Organisation is engaged in development of an international standard for Energy Management Systems (EnMS) which will become "ISO 50001". This new standard will build on the successes of both the EN16001 EnMS standard that has been used by dozens of European companies, as well as the ANSI/MSE 2000:2008 EnMS standard that is currently being used in several pilot projects in the USA and Ontario. This paper provides an overview of the key points of the EnMS standards, and describes how they can be used to drive sustainable energy reductions in the metallurgy industry.

Jan 1, 2010

By S. Sopher, C. Barsotti

"Inco Gold Company was created in 1987 as an unincorporated business unit of Inco Limited. In 1988, Inco Gold Management Inc. was incorporated to supply management, exploration and engineering services to this unit. The first new project, at Casa Berardi, Quebec, was brought to production in September 1988, less than two years after completion of exploration. For 1989, Inco Gold's exploration and capital expenditures have been budgeted at approximately $94 million, a record level. Inco Gold holds interests in more than 80 precious metals ventures and prospects in Canada, the United States, Brazil, Indonesia, Papua New Guinea and France. The most advanced projects, in addition to Casa Berardi, are at Mineral Hill, Jardine, Montana, where initial production is anticipated in the third quarter of1989, and Crixas in central Brazil, where production is scheduled to begin during the fourth quarter of the same year.BackgroundTraditionally, Inco Limited's mineral exploration has concentrated on nickel and other base metals but since the early 1980s Inco's exploration activity has focussed strongly on precious metals, principally gold. As a result, three deposits have been discovered and developed . In order to accelerate the establishment of a strong gold mining enterprise with its own specific growth and profit objectives, Inco Gold Company was created in 1987 as an unincorporated business unit. At the end of 1988 Inco Gold's share of drill-indicated gold reserves was approximately 14 million short tons containing 3.4 million ounces of gold.At Casa Berardi in northwestern Quebec, one mine is in production and another is planned to open in 1990. Properties at Crixas in Brazil and at Jardine, Montana, U.S.A., were being readied for production in 1989. By 1991, Inco Gold's share of gold production is expected to be 125 000 ounces with a target of 400 000 ounces annually by the mid-1990s."

Jan 1, 1990

By W. Dziurzynski, St. Wasilewski, T. Palka, A. Krach

"Air parameter monitoring systems, regardless of gasometrical protections, provide a significant number of measurement data. The obtained data broadens the knowledge on processes taking place in underground workings and shows the relationships and influence of machines and technological processes on the variability of ventilation parameters in the areas of longwalls. Nowadays, computer simulation methods are increasingly used to reproduce the flow of air and methane mixture in the area of longwalls equipped with shearers. The paper presents the results of a research experiment covering a long-term observation of a longwall area during mining with a shearer using sensors from the mine's monitoring system. Data from sensors for methane concentration, pressure and velocity were used and additional ventilation measurements were taken to determine the parameters characterising the air flow in the area. The influence of different machine cycles in the longwall on the changes of air parameters in the area of the longwall was shown. A numerical model of the ventilation area was developed and the computer program VentZroby was used for the calculations, which allows for the simulation of the process of ventilating the area of the active longwall during the extraction of coal with the use of a shearer and haulage of the run-of-mine. Computer simulation of the influence of the shearer's operation and the methane inflow associated with the distribution of the mixture of air and methane was carried out. The results of the simulation were compared with the data recorded by the monitoring system’s sensors during the measurement experiment. Comparison of the recorded methane concentration courses with the results of a computer simulation of the air and methane flow conditions in the mining area showed changes in the gassiness. INTRODUCTION Studies carried out in the Polish and global mining industry show that methane is an obvious factor in limiting mining production due to the loss of continuity in the operation of longwall complexes in hard coal mines under methane emission hazard (Schatzel et al., 2008). In addition, methane hazards have a significant impact on the safety of the operators of machinery in the longwall. The requirements of Polish regulations and the practice of safe operation of mining longwalls require correct determination of gas concentration, volume flow, as well as pressure and temperature of the flowing air. As part of the research undertaken in the Budryk (Wasilewski, 2010) and Bielszowice (Dziurzynski et al., 2009) mines to assess the methane hazard in the longwalls and workings in the vicinity of the longwall, research experiments were carried out, during which air parameters were recorded by the mine monitoring system and additional testing equipment in different cycles of shearer operation."

Jan 1, 2019

By J. N. Van der Merwe, M. Mathey

"The development and mechanical characterization of coal-crete, a composite material generated from coal fragments and some binder material, is described in this paper. Coal debris was obtained from a colliery in South Africa. The binder used in the study basically consists of cement and water, and further ingredients are added to the mixtures, such as sand, fly ash and polymers, in order to investigate alterations of the mechanical properties of coal-crete.Results from over 220 mechanical tests on coal-cretes with various binder mixtures give consistent trends for the material’s behaviour. Linear relationships are suggested between the uniaxial compressive strength, Young’s Modulus and the indirect tensile strength of the coal-crete.It is shown that mechanical properties comparable to coal can be achieved. Coal-crete is therefore suitable for physical modelling of mining situations in experimental studies and for use as backfill in underground coal mines. The latter application is particularly attractive when refuse coal is used as aggregate material. The indicated trends in this study may be used as a guideline for individual coal-crete design needs. However, some uncertainty remains as to the influence of particle shape, size and gradation, coal rank and age of the coal-crete. These aspects are recommended for further research."

Jan 1, 2015

By C. W. Davis

AN inclined shaft is usually more difficult to sink than a vertical shaft, yet it is often chosen because of the subsequent saving in cross-cuts required to reach an inclined ore body. This paper briefly discusses the factors which led to the choice of an incline and then describes the operations involved in the preparatory work and in the sinking. These operations included a programme of mining out the underground facilities and installing the structures required for a hoist-room, cable-raise, waste-pass, ore pass, two sets of skip dumps, and a collar station equipped with counterbalanced drop-rails. The shaft was sunk 1,000 feet and four stations were cut, each with loading pockets. As the sinking progressed, the rock changed from hard porphyries and dense cherts to blocky limestones and earthy rubble. These conditions called for a change in methods and it is to the red it of the shaft-sinking crew that they overcame the new difficulties as the shaft progressed, while maintaining a satisfactory monthly advance. The section mined out was nine feet six inches by seventeen feet overall. This gave room for three compartments: two skip compartments four feet three inches by five feet nine inches inside the timber, to handle two-ton skips, and a manway three feet six inches by five feet nine inches. The sinking began on December 16th, 1941, and was completed on February 15th, 1943.

Jan 1, 1945

By W. van der Merwe

With the gold industry looking to process more complex ores, the online measurement and control of cyanide addition to the gold leaching circuit has become more crucial. This paper compares the two commonly employed "free" cyanide online analysis methods (amperometric and potentiometric end-point silver nitrate titration) with the common site laboratory rhodanine endpoint silver nitrate titration and ion selective electrode methods. Measurement differences between these methods are presented and discussed for cyanide solutions containing copper and zinc with varying cyanide to metal ion ratios. The resulting cyanide available to leach gold is also compared with these measurements.

Jan 1, 2011

By S. J. Cook

Outstanding advances among the metals, marked the mineral production records for Canada during the first half of 1925. Production of metals and non-metals reached a total value of $90,347,698. as compared with $84,307,385. in the first half of 1924, an increase of 7.16 per cent. Metals and non-metals produced during the calendar year 1924 were valued at $17 4,202,537.; production during the first half of 1925 showed a sum equal to 51.86 per cent of this total. Advances among the metals were general. Gold rose to a new record. Lead advanced 62.41 per cent over the high mark attained in the first half of 1924. Nickel production was well maintained. Copper was up a million pounds. Silver showed increased values. Zinc followed the trend in lead to almost double the output recorded in the first half of 1924. Cobalt production continued to improve. Despite the loss due to the protracted strike in the Nova Scotia coal mines which reduced the output of coal in that province; during the six months ending June, to less than half the tonnage reported in the first six months of 1924, improved conditions throughout the rest of the non-metal mining field resulted in the production of non-metals during the half-year reaching a total value of $31,199,233. as compared with $36,844,286. in the first half of 1924; the loss in the value of coal output al one amounted to $5,723,873, while the decrease in the aggregate value of non-metals amounted to only $5,645,053.

Jan 1, 1925

By David Stone

North American Palladium is the owner/operator of the Lac des Iles mine located 115 km north of Thunder Bay, Ontario. The mine has produced an average of 65,000 ounces of palladium since 1994. Lac des Iles is currently undergoing the first phase of a major expansion that will increase ore production from 2,400 tons per day to 15,000 tons per day. A future expansion is being contemplated for 30,000 tons per day. The current expansion will increase palladium output to 250,000 ounces per year. The mine plan for the ultimate pit results in an excavation 1 km long by 800 m wide and over 450 m deep. This makes the ultimate pit at Lac des Iles one of the ten deepest open pits in the world, and the largest in Canada. This paper outlines the geotechnical data collection and design methodology for the ultimate open pit at Lac des Iles.

May 1, 2001

By B. J. McKay, K. Schneider, H. B. Nadendla

"A series of experiments were conducted to assess the impact of zinc additions on the morphology and soundness of the interface of Al-Mg compound castings. It was found that high amounts of zinc (>15wt%) are necessary to affect the morphology and microstructure of the interface. At these zinc concentration levels, the formation of the zinc-rich phases t1 and ? were observed along with the Al-Mg intermetallic phases ß and ?. The micro hardness of all phases across the interface was found to be similar, ~200 Hv. This even hardness gradient is thought to avoid mechanical failure in the interface under load. In samples containing large concentrations of zinc (>15wt%), the formation of bubble shaped voids as well as the complete transformation of the aluminium alloy was observed. While the exact mechanism causing the voids has not been identified it thought to be connected to the Kirkendall effect. INTRODUCTION Conventional single material components are increasingly failing to meet the demands, in terms of cost and performance, of the transport industry. Compound castings have been identified as a promising alternative as they possess a number of benefits (Bührig-Polaczek, Röth, Baumeister, Nowack, & Sussmann, 2006). Compound casting is described as a process in which a metallic melt is cast around a solid metal shape. Preliminary research has concluded that for the stability of such a resultant hybrid structure it is imperative that both metals form a sound connection via form closure, force closure, or material bonding. A continuous material bond between the two metals is also highly desirable as the formation of a crevice between the metals could lead to galvanic corrosion, particular in a humid environment (Lao, 2013; Rübner, Günzl, Körner, & Singer, 2011). Even though Al-Mg compound castings could offer the biggest potential in terms of weight savings to date only a limited amount of research concerning such structures exists."

Jan 1, 2018

By B. Garitte, O. K. Mahabadi, P. Marschall, A. Lisjak, H. R. Müller, T. Vietor, G. Grasselli

Numerous research studies have shown that clay rock formations exhibit favourable characteristics for the deep geological disposal of radioactive waste. However, one main concern is that the favourable long-term isolation properties of the intact rock mass could be negatively affected by the formation of an excavation damaged zone (EDZ) around the underground openings. The goal of this paper is to present new rock mechanics insights into the phenomena involved in the EDZ formation and evolution processes in Opalinus Clay, a clay shale currently being assessed as a potential host rock for an underground repository in Northern Switzerland. More specifically, discontinuum-based computer simulations, using a hybrid finite-discrete element method (FDEM) approach, were applied to two case studies considering circular excavations in an anisotropic Opalinus Clay formation. In the first case study, numerical modelling was applied to the HG-A experiment, a long-term in-situ test carried out at the Mont Terri underground rock laboratory to investigate the hydro-mechanical response of a backfilled and sealed microtunnel. A mechanistic analysis of the fracturing processes involved in the EDZ formation was carried out. In the second case study, the long-term effect of the bentonite backfill swelling on the EDZ around an emplacement was numerically analyzed. Overall, the simulation results highlight short-term distinctive rock failure kinematics due to the bedded rock structure, as well as a long-term reduction of the excavation-induced fracture porosity in response to mechanical loading.

Jan 1, 2015

"Since the publication of a literature review on this topic (McIvor and Finch. 1986), the author has been involved in more than thirty rod milling efficiency tests at seven different milling operations. There have also been several interesting additional articles on rod milling found in the literature. This update describes the most important findings from investigations carried out since the previous review, as well as developments in the techniques used to evaluate the grinding efficiency of rod mills.Rod Mill Power DrawA series of power draw versus charge level measurements were taken on the rod mills at Leg Mines Selbaie and Kidd Creek Mines Limited (McIvor. 1989). These revealed a significant (about 10070) loss in power draw with the installation of new liners, a common observation among rod mill operators. This loss in power draw depends on the liner design, particularly the average thickness and lifting face profile of the new liner. The theoretical power usage of both mills was approximately 5070 lower than that given by the Allis-Chalmers power draw formula (Rowland. 1982).The shape of the power draw versus charge level curve suggested an opportunity for reducing media consumption. By increasing mill speed, power draw could be maintained with a smaller mill load, most significantly for mills operating with high charge levels. Analysis of data from 62 installations confirmed this (McIvor, 1989). On average, a 10 percentage point increase in critical speed results in a 15070 in specific media consumption (Le. kg of steel consumed per kWh of energy consumed). Table 1 lists a number of relatively high speed rod milling installations. No negative effects on the drive train, liner life, or the tendency for rods to tangle have been reported. A reduced lifting angle of the new liner leading face (e.g. 45 versus 90 degrees from the mill perimeter) is recommended for higher speed rod mills (Leclerq, 1990)."

Jan 1, 1995

By Åke C. Rasmuson, Mahmood Alemrajabi, Kerstin M. Forsberg, Kivanc Korkmaz

"In the present study the recovery of a Panasonic Prismatic Module 6.5 Ah NiMH 7.2 V plastic casing hybrid electric vehicle (HEV) battery was investigated, separately processing the anode and cathode electrodes. The composition of the electrode materials was determined by total dissolution and analysis using ICP-OES. Nickel is the dominant metal in the active materials (65% by mass in the anode and 70% by mass in the cathode). Most of the rare earth elements (La, Ce, Nd, Pr and Y) are located in the anode active material, whereas only a small amount of Y is found in the cathode material. The electrode materials were further characterized by SEM-EDS and powder XRD. The electrodes were leached in sulfuric acid and in hydrochloric acid under different conditions. The dissolution was followed by taking out samples and analyzing the concentration of REE, Co, and Ni using ICP-OES. The results indicate that the dissolution of nickel could be limited by slow dissolution kinetics of nickel oxide. Further, it was found that light rare earths are lost through precipitation during sulfuric acid leaching with increasing extent as the temperature and sulfuric acid concentration increases. The separation of REE from the sulfuric acid leach liquor by precipitation as NaREE(SO4)2.H2O and from the hydrochloric acid leach solution as REE2(C2O4)3.xH2O have been studied by performing experiments using battery leach liquors. INTRODUCTIONIt is well known that the Hybrid Electric Vehicle (HEV) is becoming more common due to economic and environmental reasons. Batteries are widely used in HEVs’ such as automobiles or larger trucks for transportation purposes. The most common type of battery in these vehicles is nickel metal hydride (NiMH), largely due to Toyota's decision to use them in their popular Prius. More than two million hybrid cars worldwide are running with NiMH batteries, such as the Prius, Lexus (Toyota), Civic, Insight (Honda), and Fusion (Ford). Panasonic manufactures HEV prismatic NiMH batteries that have been used by Toyota and GM (among others), while Sanyo manufactures HEV cylindrical cell NiMH batteries, which have been used by Honda and Ford."

Jan 1, 2016

By A. C. Munro

The concrete work on the new Britannia mill was started in April, 1922. The erection of steel commenced on July 10th, following. The installation of wood work and machinery , began on November 4th of the same year and was pushed to completion in January, 1923. The new mill building is an all steel structure enclosed with galvanized corrugated steel. All main floors and foundations are of reinforced concrete, which makes the building practically fireproof throughout. The mill building rises on a steep hillside to a vertical elevation of 210 feet and has seven distinct floors, for the various opera-tions. Only one elevator, with 30-foot centres, is used in the entire mill. The building is exceptionally roomy and well lighted, both by day and night. The capacity of the mill, as originally designed, was to be 2000 tons daily, but this tonnage can be readily increased to over 3000 tons daily by making slight changes in the fine grinding equipment; in fact, an average of 2700 tons per 24 hours was maintained throughout the month of September.

Jan 1, 1923

By R. A. Rabnett, G. Paget, Patrick Walsh

"Tumbler Ridge, Canada's newest resource community, has been developed differently than have been other resource communities.Since its conceptualization, emphasis has been placed on the establishment of a traditional municipal government at early a stage as possible.Planning f or the community goes back to 1977. By then, extensive study by provincial agencies had shown a new resource town would be required to exploit north east coal. The Ministry of Municipal Affairs, in conjunction with a consultant named R.A. Rabnett began the extensive Tumbler Ridge conceptual plan.The results of the conceptual plan are evident in the organizational and planning goals of Tumbler Ridge. In every aspect from the election of officials to some financial matters, the town functions as a normal municipality. With the resource companies of the North East Coal Development within its municipal boundaries. Tumbler Ridge has been able to debenture its capital projects against its municipal tax base.The town's ability to function as a normal municipality is enhanced by its control over Crown land it has purchased from the province. This gives it further control over the development of the community and helps in establishing agreements with the resource companies and the provincial government to ensure that housing and service needs are met. While resource company representatives sit on certain municipal committees, their roles are advisory in nature.The community continues to move toward full municipal status and will have a fully elected Council by 1986.BackgroundPlanning for the development of northeast British Columbia coal resources began in 1976 under the aegis of the provincial Cabinet Committee on Coal Development. A series of subcommittees were established including a Townsite/Community Development subcommittee. The Ministry of Municipal Affairs chaired this subcommittee and continued as the lead agency for the provincial settlement planning effort over the period 1976 to 1981."

Jan 1, 1983

By D. Ling, Santos. R. M., T. Van Gerven, M. Guo

The valorization of alkaline waste materials from thermal processes utilizing intensified mineral carbonation routes is investigated. The principal advantages of this approach are the chemical stability and storage safety of mineral carbonates, the opportunities for process integration presented by the technology, and the potential for conversion of low-value materials into useful products. Treatment and disposal of steel slags are a costly burden on steel plants. Sustainable solutions for Argon Oxygen Decarbonisation (AOD) and Continuous Casting (CC) stainless steel slags and Basic Oxygen Furnace (BOF) steel slag are desired. An integrated on-site mineral carbonation approach is envisaged as a favourable solution.

Jan 1, 2011

By Y. W. Pan, Y. R. Liu

The disturbed natural rock mass tends to equilibrium state accompanying with non-equilibrium evolution process which has significant influence on the long-term stability of engineering structure. The deformation development in the non-equilibrium evolution is determined by two intrinsic processes, trend to equilibrium and damage development, which can be illustrated by evolution of excavated tunnel. Thus the creep and damage must be taken into account in study of non-equilibrium evolution process. Within Rice’s irreversible thermodynamics with internal state variable (ISV), the conjugate force function which equals to zero is a convex surface which divide the stress space into two parts, called equilibrium and nonequilibrium stress space respectively. The concept of effective stress of non-equilibrium has been proposed, in which the stress difference (d - d ) are the effective driving forces of non-equilibrium evolution process with hardening and damage effective. The formulations of inelastic strain rate and energy dissipation rate have been recast in the form of effective stresses. The inelastic complementary energy (ICE) is proposed to measure intensity of non-equilibrium evolution of material system. The specific equations of conjugated forces and kinetic equations of internal state variables are presented. The ICE and rate of energy dissipation are all calculated to be used to evaluate long-term stability of geo-engineering. The results show that rate of energy dissipation may be more convenience and flexible than ICE for internal state variable constitutive equation of rock mass.

Jan 1, 2015

By A. Robles-Vega

Personnel of Mexicana de Cobre, a subsidiary of Southern Copper located in Nacozari, Sonora Mexico have been working in the past few years on the development of a process to treat and manage, in an environmentally accepted practice, the residues and effluents generated during the process. To date, this team has been reviewing existing technologies and also has explored new alternatives. At the end of this phase, a novel, efficient and complete process has been configured which will be able to treat some solid and liquid streams such as Teniente converter dust, Peirce Smith converter dust, a Sb-rich precious metals slag, copper refinery electrolyte bleed, acid plant blowdown and an acid bleed of the precious metals plant. The process will consist of a leaching stage, followed by a very selective copper precipitation using novel technology which has been named as back reactions. After copper precipitation, impurities (As, Sb and Bi) will be precipitated mainly as arsenic trisulfide (As2S3) using H2S(g) which will be generated by means of a new process developed in our company. At the end of the process, small volumes of arsenic trisulfide will be vitrified and then disposed as a stable residue.

Jan 1, 2007