Search Documents

By C. Peña, C. A. Zaror, M. Bustamante, M. Vega

The goal of this paper is to present the carbon footprint of Chilean cathodic copper, as a function of the electricity generation mix, ore grade, and process efficiency. Ore grades and acid leach-solvent extraction-electrowinning (LX-SX-EW) yields in the range 0.5-1.0% and 60-80%, respectively, were considered here. Additionally, electricity supply from two Chilean suppliers, SING (1.0 ton CO2/MWh) and SIC (0.4 ton CO2/MWh) was assessed. Simulation results show that oxide plants located in northern Chile, served by the SING network, feature carbon footprint within 4.3 - 11.4 MWh I ton cathodic copper, as compared with 3.5 - 9.3 MWh I ton copper in plants served by SIC. The footprint was found to increase as ore wade and process yields decrease.

Jan 1, 2011

By J. A. Bossert

"In 1957, the Department of Mines and Technical Surveys (now Energy, Mines and Resources Canada) issued their first certificate for a fire-resistant conveyor belt. The testing procedure used was a combination of those used in the U.S.A. and the U.K. Subsequently, certification was granted to fire resistant electric cables (1974), fire-resistant mine duct material (1976) and fire-resistant hydraulic fluids (1978).Until recently, the testing procedures were copied from either the U.S. or the U.K. However, since the founding of the new Canadian Standards Association (CSA) Steering Committee for Electrical/Mechanical Mine Safety in 1981, these requirements have come under the close scrutiny of new CSA technical committees who will attempt to adopt or change the existing procedures to meet Canadian needs. This paper outlines the existing test requirements and attempts to predict how they will appear after ""Canadianization"" by the CSA committees.IntroductionFires in underground mines have always been considered more serious than in other locations because of the confined space and limited atmosphere. A fire can make escape difficult or impossible if it is blocking all of the routes to the surface. Also, the products of combustion from an underground fire can asphyxiate anyone not having self-contained breathing apparatus.In an underground coal mine, the consequences of a fire can be even more serious because of the presence of methane and coal dust in the atmosphere (which can explode) and because the coal itself is combustible.For these reasons, the inspection authorities having jurisdiction over underground mine s in Canada are quite concerned about the flammability of any materials that are used in quantity in the underground environmentAs early as 1957, the Canadian Explosive Atmospheres Laboratory (CEAL) was asked to certify conveyor belting as fire-resistant. This is because many miles of this material are used in underground mines in Canada and, as it generally travels through the mine, it is a perfect vehicle for spreading a fire."

Jan 1, 1982

By W. A. Jones

"The Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is near the north end of lot 1, con. II, Hislop tp., Ontario. The property comprises the north half of lot 1, con. II, and the south onethird of lot 1, con. III. It is readily reached by a good motor road from the village of Ramore, 7 1/2 miles to the southeast on the Ontario Northland railway. The mine is being developed to a depth of 1,500 feet, and the current daily production rate is approximately 300 tons. From the inception of operations in March 1935 until December 31, 1945, 692,000 tons of ore, with a total value of $5,762,685, was milled . The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines.TYPE OF 0REBODIES AND MINERALIZATIONThe orebodies consist of lens-shaped and pipe-like stringer lodes and tabular vein zones composed of parallel quartz stringers. The host rocks are steeply inclined eruptive breccias and tuffs, striking N.70°W., intruded by very small stocks of red syenite. The orebodies appear to be spatially related to an intricate system of fault planes. Hydrothermal alteration is widespread and is not zonally related to individual quartz stringers. The wall-rocks contain abundant fine-grained pyrite, but gold is confined to the quartz stringers.RELATIONSHIP TO REGIONAL STRUCTURELack of outcrops has prevented the detailed mapping of the Keewatin complex in the vicinity of the Ross mine with the degree of success that has been achieved in the Porcupine area.A northwesterly trending belt of slates and greywackes, bounded by faults, forms the central part of a broad anticlinal arch about 3 1/2 miles north of the Ross shaft. Lava flows forming the south flank of the structure face south toward the mine. If the sediments are to be tentatively correlated with the large areas of Keewatin slates and greywackes of the Porcupine area, it must be assumed that they are younger than the lava flows and that they have been down-faulted."

Jan 1, 1954

By Laszlo Imreh, Pierre Trudel, André C. Tessier

"The Siscoe gold mine is ranked as the fourth largest mine in the history of the Val d' Or mining district with a total production of 27.4 tAufrom1929 to 1949. Most of the gold mineralization occurred in quartz veins, hosted in a small (.69 km2) intrusion of altered quartz gabbro known as the Siscoe stock. The southern contact of the Siscoe stock is crosscut by a major shear zone (the ""K"" zone) trending 295/80 NE and from which gold mineralization was also exploited within the limits of the stock. Field and petrographic observations of the Siscoe stock combined with chemical analyses of major, trace and rare earth elements of the stock and its volcanic host rocks (Dubuisson Formation) suggest that:The Siscoe stock comprises four alteration facies formed from a homogeneous precursor: 1) the actinolite - Mg-chlorite facies, characterized by low FeOt,Na2O andTiO2 , and highAlp3 and MgO; 2) the albite- Fe-chlorite facies, containing high concentrations of FeOt and Nap; 3) the Mg + Fe-chloritefacies, which is transitional between the actinolite- Mg-chlorite and albite- Fe-chloritefacies; 4) the carbonate-chlorite facies, which consists of rocks that were subjected to extreme hydrothermal alteration, is spatially associated with mineralized veins and part of the K-zone. The first three facies are depleted in SiO 2, CaO and Au, and enriched in MgO, relative to fresh rocks of the Siscoe stock and the equivalent rocks of the Dubuisson Formation.Hydrothermal fluids introduced mainly along the K-zone ""channelway"" induced three types of element remobilization, resulting in the various alteration facies: 1) redistribution of elements within the stock from one facies to another (e .g., FeOt, Nap, Ti02 migrated from the actinolite- Mg-chlorite facies to the albite- F e-chlorite and Mg + Fe-chlorite facies); 2) remobilization of elements from the intrusive rocks into veins (e.g ., SiO 2 and CaO ); 3) introduction of elements by hydrothermal fluids in rocks of the Siscoe stock (e .g., Al2O3, MgO, H2O, CO2 and FeOt).The Siscoe stock and the Dubuisson Formation form part of the same tholeiitic suite. Similarly, the Bourlamaque batholith and the Val d'Or Formation belong to a single calc-alkaline suite. In view of this relationship, dissimilarities between the petrochemistry of the Siscoe stock and the Bourlamaque batholith suggest that the two intrusions are not co-magmatic.Finally, gold may have been leached from rocks of the Siscoe stock and remobilized into the quartz-carbonate mineralized veins. In order to account for the total production at the Siscoe mine, approximately 1.2 km3 of the Siscoe stock is thought to have been partially leached of its gold."

Jan 1, 1990

By Erik Q. Dahl

The strength of green and sintered pellets during reduction under various conditions in a laboratory kiln has been investigated. Equipment and test methods are described, together with the results obtained. The strength of sintered pellets drops sharply when the reduction starts, and goes through a minimum at the 70 per cent oxidation level. At more advanced reduction, the strength increases with increasing metallization. Successful use of green pellets as kiln feed requires that more attention be paid to the pellet preparation than is necessary when producing pellets for separate sintering. In particular, the ores have to be ground to a greater fineness. The initial strength of green pellets is low. Below the 70 per cent oxidation level, however, the strength of these pellets is about the same as the strength of sintered ones. Additions of such materials as silica, limestone and anthracite coal; within reasonable limits, affect the strength only slightly.

Jan 1, 1966

A series of field and laboratory evaluations were conducted in order to characterize the effects of a Mann+Hummel SMF-AR® diesel particulate filter (DPF) system on the aerosols and criteria gases emitted by diesel engines. This system, with a durable sintered metal filter media and available active regeneration via an on-board electrical heater, has been considered for retrofitting diesel engines used in light- and medium-duty underground mining applications. Two DPF systems were installed on a forklift and locomotive from the underground mining fleet of the Vale?s Creighton Mine and evaluated over a 1,500-hour trial. This evaluation was complemented with field and laboratory emissions tests. The field tests were performed on the vehicles while at the Creighton Mine surface shop. During those tests, the emissions were assessed for the engines operated at hydraulic stall, high idle, and low idle conditions. The laboratory tests were executed at the diesel engine emissions laboratory at the National Institute for Occupational Safety and Health (NIOSH), here the DPF removed from the forklift was further evaluated at four steady-state engine operating conditions as well as at transient conditions using a custom-designed duty cycle. Very similar methodologies were used during field and laboratory tests to measure concentrations of aerosols and criteria gases in the diesel exhaust, both upstream and downstream of the DPF system. The concentrations and size distributions of aerosols were measured using a fast mobility particle sizer spectrometer, in exhaust diluted by a partial flow dilution system. The concentrations of CO2, CO, NO, and NO2 were measured in the raw exhaust using a Fourier transform infra-red spectrometer. Both field and laboratory emissions tests showed that the evaluated DPF systems were very effective in reducing aerosol emissions from all tested engines, and for all test conditions. The systems were found to have minor effects on gaseous emissions from those engines. The findings from this study should help the mining industry to better understand the benefits and challenges of using DPF systems to control the exposure of underground miners to diesel aerosols.

Aug 1, 2013

RÉSUMÉ L’estimation la plus précise possible des coûts de minage est d’extrême importance pour les études de préfaisabilité afin de diminuer les risques financiers des projets miniers. Les méthodologies existantes d’évaluation des coûts de minage ne permettent pas de les évaluer avec des marges d’erreur acceptables tout au long de l’évolution des projets miniers. Elles visent à évaluer les coûts unitaires de minage des études préliminaires de faisabilité, pour les principales méthodes d’exploitation, en prenant pour l’hypothèse que ces coûts dépendent principalement du taux d’extraction journalière. Si cette hypothèse peut être justifiée pour l’évaluation du coût d’opération, elle est fort discutable pour l’évaluation des coûts de minage. Pour démontrer que cette hypothèse est inadéquate nous avons analysé la méthode d’exploitation la plus populaire sur le continent nord-américain c’est à dire celle par chambres vides avec retrait horizontal (Hr – Horizontal retreat), ou « Longhole » et celle avec retrait vertical (VCr - Vertical Crater retreat). Il ressort de cette analyse que les coûts unitaires de minage dépendent principalement des conditions géotechniques du massif rocheux et de la largeur du gisement et non pas du taux d’extraction journalière du minerai.

Jan 1, 2010

By T. Wajima

"A novel carbonaceous adsorbent for recovery of nickel from nickel plating waste solution was prepared from rice straw using sulfur impregnation. The rice straws were cut to 1 cm pieces, and then immersed in 0.01 - 3 M K2S solution to prepare sulfur-immersed materials. The immersed-materials were heated at 100-700 ºC in nitrogen gas to produce the sulfur-impregnated carbonaceous adsorbent by pyrolysis. The contents of carbon and sulfur in the adsorbent and abilities of adsorbent to recovery nickel from aqueous solution were examined. The contents of carbon and sulfur in sulfur-immersed materials are almost same as those in raw material. In pyrolysis, with increasing the heating temperature to 200 ºC, the contents of carbon and sulfur are almost constant, and then above 300 ºC those increase. The recovery for nickel using raw material, sulfur-immersed material and the product pyrolyzed at 100 - 200 ºC are almost same, and with increasing the heating temperature to 400 ºC, that of the product increases, and above 500 ºC that of the product decreases. In immerse step, with increasing K2S concentration, the carbon content of the product at 400 ºC gradually decreases, the sulfur content of the product increases, and the recovery for nickel using the product gradually increases and then above 1 M K2S decrease. The product prepared from material immersed in 1 M K2S solution at 400 ºC indicates a maximum recovery for nickel ion. The product can adsorb nickel ion in nickel plating waste solution coexisting with phosphate ion, and adsorbed nickel ion in the product was deposited as nickel metal after heating at 1000 ºC under N2 atmosphere.INTRODUCTIONRice is the second world’s largest cereal crop after wheat, but produces large amount of straw residues, of about 330 million metric tonnes. Rice is a widely grown crop in Asia, and rice straw is produced as a by-product of rice production. In most parts of rice fields, open-field burning of rice straw is commonly practiced in the region when there is limited time to prepare a field for the next crop. However, open-field burning of crop residues is an uncontrolled combustion process during which air pollutants are emitted into atmosphere. These air pollutants have significant toxicological properties and are potential carcinogens (Gadede et al., 2009). Although wildfires are prohibited in cultivation fields of most countries, farmers usually keep on burning their crop by-products. Biomass burning is an important source of aerosol particles which may affect local and regional air quality (Gao et al., 2011), and also contribute to global climate changes."

Jan 1, 2016

By Alan A. Barton

Introduction The Little Long Lac mine is situated in the Thunder Bay mining district, township of Errington, Ontario. The mine is located on the south side of the most westerly bay of Little Long Lac. The property consists of 36 claims, which comprise some 1,400 acres. This group of claims was staked in August, 1932, by Tony Oklend and Tom Johnson, and, after surface sampling, was optioned by the present controlling interests, who diamond-drilled it during the winter of 1932-33. In early spring, a small steam-driven plant was installed, and shaft sinking commenced on June 1st, 1933. During the summer, all supplies are transported to the mine from Hardrock station, at mileage 18 on the Canadian National Railway line from Longlac to Port Arthur. At Hardrock, which is seven miles from the mine, the railway skirts a bay of Little Long Lac, and supplies are loaded directly from railway cars to scows. Two scows are used, of 30-and 45-ton capacity, respectively. A 36-ft. pointer, powered by a 35 h.p. engine, is used as a tug. A good winter-road has been cut out from Geraldton to the mine, for winter transportation. Geraldton is about two miles north of the mine, and is also located on the Canadian National railway. A hard-surface road is now being constructed for summer as well as winter use. Geology The Little Long Lac gold area covers the northern limits of a large synclinal structure, the contact of the Keewatin flows and sediments, striking about twenty degrees north of west, with the dip of the sediments varying from eighty degrees north to seventy degrees south, the average being around eighty degrees south. The vein worked by Little Long Lac Gold Mines occurs in massive sedimentary rock of about the composition of arkosic or quartzitic greywacke, and consists of a shear-zone up to fifteen feet in width, striking N.75°E. and dipping steeply to the south, which has been filled by numerous narrow, parallel quartz veins and. veinlets. These are well mineralized. with arsenopyrite, pyrite, and some chalcopyrite and stibnite, and carry considerable quantities of visible gold. They show more than one age of quartz deposition, the quartz being fractured and re-cemented. The arkosic rocks separating the veins and veinlets are also slightly mineralized with pyrite. Work to date has indicated the probability that the vein-shear is controlled by local drag-folding.

Jan 1, 1935

By Y. Wang

In this study, homogeneous (unseeded) precipitation of nesquehonite (MgCO3.3H20) by the reaction of MgC12 with (NH4)2CO3 in supersaturated solutions at 30 °C was investigated. Factors which influence the precipitation of MgCO3.3H20, such as initial concentration, temperature, stirring speed, titration speed, equilibration time, have been studied. SEM images show that the initial concentration and titration speed have significant effect on nesquehonite's crystal morphology and particle size. In addition, stirring speed and equilibration time also have some influence on its properties. With the optimization of operating conditions, the crystals can grow up to a length of about 40µm and a width of 5µm, indicating good filtration properties. High purity nesquehonite obtained in this study was calcined to produce highly pure MgO at 800 °C as shown by XRD results. The novel process may be used to separate Mg and Li from high Mg/Li ratio brines in Qinghai, China.

Jan 1, 2007

By A. Mortazavi, H. Nasab

"The storage of petroleum products on surface is associated with difficulties and limitations. Accordingly, a viable alternative is to excavate underground space in rock and provide a safe way for oil storage. Soft rocks such as salt domes provide good conditions from environmental and operational points of view. The potential for high-volume storage and low permeability are encouraging aspects for oil storage in salt domes. The complicated shape of oil storage caverns, the complicated behavior of salt rocks, and boundary conditions associated with large underground openings are important challenges in the design of oil storage caverns. The aim of this paper is to delve into the stability and deformation mechanisms of storage caverns created in salt domes. A parametric study of effect of the cavern size, orientation, and depth is carried out as a function of ground stress regime. The stress field and deformation mechanisms are calculated for each case aiming at providing design guideline.INTRODUCTIONOne of the most popular soft rock that is used for underground oil storage is salt rock (halite). Salt rock has particular characteristics which makes it suitable for oil storage. Salt rock has several advantages for oil storage, these are: high production rate, high degree of availability, short filling period, high level of safety and low permeability [1]. The low permeability is due to the fact that halite deforms in a plastic manner over a wide range of pressures, temperatures and rates of deformations. This property prevents joints or gaps opening up in the formation, thus preventing the escape of liquids and gases. The state of stresses around the cavern in salt domes depends on the depth of the cavern (initial stresses and rock mass temperatures are increasing with depth), the in-situ stress state within the rock mass, and the internal oil pressure in the cavern. Furthermore, the salt creep behavior and the cavern geometry are influencing stress redistributions during loading and unloading phases.Rock mass structure, cavern geometry, material behavior and cavern operation patterns require complex physical models to describe the load-bearing behavior of the geomechanical structure. The determination of stress, strain and deformation in the rock mass due to cavern construction and operation are complex problems which can be evaluated employing numerical tools such as the Finite Element Method (FEM) or Finite Difference Method (FDM). In this study, the finite difference method was used to evaluate the behavior of oil storage cavern in salt rock."

Jan 1, 2015

By David L. Anderson

"The objective of this paper is to describe the potential impact of inter-provincial competition f or new output capacity on the Canadian potash industry. It will be shown that the ramifications of such actions are potentially severe, especially since the potash industry is one of the few non-fuel minerals in which Canada purportedly possesses a significant degree of market power. More specifically, the paper addresses the impact of possible expansions in New Brunswick, Manitoba and, perhaps, Saskatchewan. The findings suggest that such initiatives could result in substantial excess capacity and the dissipation of monopoly rents. In summary, given the market structure of the industry, it is unlikely that the employment and economic effects associated with industry expansion will offset the loss in national welfare attributable to rent dissipation.IntroductionThe objective of this paper is to discuss the potential impact of inter-provincial competition for new output capacity on the Canadian potash industry. The ramifications of such competition are potentially severe: given that the potash industry is one of the few non-fuel minerals in which we purportedly possess a significant degree of market power(1), it is important that sound supply management practices are followed. However, possible initiatives by New Brunswick, Manitoba and, perhaps, Saskatchewan may initiate an inter-provincial competition which could result in substantial excess capacity and the dissipation of economic rents(2). Given the market structure of the industry, it is not intuitively obvious that the employment and economic effects associated with industry expansion will offset the loss in national welfare attributable to rent dissipation."

Jan 1, 1985

MR. J. F. MYERS, Consulting J3eneficiation Engineer, Greenwich, Conn.: In the written discussion contributed by Mr. F. C. Bond in item ( 2) (page 515), speaiking about the significance of the ratio of mill diameter to the make-up ball diameter, he states: "When this ratio exceeds 100 the power and capacity of the mill are de-creased"; and the paragraph ends with a reference to the 30 per cent ball volume "with some de-crease in mill capacity". I believe this broad statement is incorrect. When we are dealing with a non-cataracting mill, pre-ceded by a good rod mill, there is a slight increase in capacity, but the power does drop. The second point that I consider needs consideration is Mr. Bond's item (8), Proper Mill Speed (page 516). This paragraph should be qualified to cover single-stage mills only. It does not apply where a rod mill is followed by a non-cataracting ball mill. The statement as is, with no qualification, gives an erroneous idea of proper mill speeds.

Jan 1, 1957

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By B. R. Rakishev

When transferring from the railway transport to the combined automobile-conveyor transport by stripping works at coal mines, it was proposed to form at the working zone a concentration horizon for reloading part of the stripping volumes at the railway transport. The procedure is adduced for substantiating parameters of bloc-panels, depending on the step of transferring of reloading points in interrelation with the intensity of the working zone?s development with observing the balanced movement of parts of the stripping zone relative to the temporary concentration level.

Aug 1, 2013

By Bruce J. Barker

"Environmental concerns have recently been growing over the disposal of reactive desulphurizing slag. Consequently, increased pressure has been placed on the foundry industry to reduce the reactivity of this slag.To address this problem, Cyanamid has developed a new product which significantly reduces the calcium carbide content of the desulphurizing slag. Testing equipment and procedures have also been developed to evaluate both the existing levels of carbide in the slag and the decreased levels which are achieved with this new material.The development and use of this engineered carbide desulphurizer has made possible significant environmental and efficiency improvements in the field of calcium carbide desulphurizing. Consequently, the lifespan of calcium carbide in ductile iron desulphurization has been increased, as have the benefits of its use in the foundry industry. IntroductionIn the production of ductile iron, calcium carbide has long been used for hot metal desulphurization external to the cupola. Its cost effectiveness, reliability and ease of use have traditionally made it the desulphurizer of choice for a great majority of ductile operations. Recently however, environmental concerns have been raised regarding the quantity of calcium carbide remaining in the slag after desulphurizing. Analysis has shown that as much as 25070 of the weight of the slag may contain active carbide. This has caused disposal concerns as calcium carbide when in contact with water, produces acetylene via the following reactionr:"

Jan 1, 1992

By Kazutoshi Haga, Batnasan Altansukh, Yasushi Takasaki, Mohd Yazid Bin Abdul Razak, Atsushi Shibayama

"In this study, the volatilization behaviour of arsenic (As) and antimony (Sb) from arsenicantimony bearing minerals such as tennantite (Cu12As4S13)/tetrahedrite (Cu12Sb4S13) in copper ore was investigated using a roasting process. Specifically, the thermal decomposition of tennantite and the arsenic volatilization were investigated under nitrogen and air atmosphere. The roasting experiments were performed at temperatures ranging from 500 to 1,200oC and different retention times using a laboratory electric furnace. The results indicated that over 95% volatilization was achieved at 700oC. On the other hand, when the temperature increased to 1,200oC, volatilization rate of Sb reached to 90%. Therefore, volatilization of Sb requires high temperature compared to As. It suggests that As and Sb can be separated using temperature difference. Selective removal of As is possible at 700oC, subsequently Sb can be recovered as a volatilized product by increasing the temperature to 1,200oC. Meanwhile, volatilization of Cu and Fe was not observed on these conditions. The content of As and Sb in the residues obtained from roasting at 700 and 1,200oC was less than 0.3 and 0.75 mass%, respectively. The Cu content in solid residue at 1,200oC increased to 34 mass%. The clean copper concentrate with lower amounts of arsenic and antimony was obtained from the process. INTRODUCTIONRecently, arsenic (As) and antimony (Sb) contents in copper (Cu) concentrates are increasing year by year. Arsenic and antimony are present with Cu minerals such as enargite (Cu3AsS4), tennantite (Cu12As4S13) and tetrahedrite (Cu12Sb4S13) that associate with copper sulfides [chalcopyrite (CuFeS2) and bornite (Cu5FeS4)]. They are normally concentrated by flotation and treated in copper smelters. However, treatment of copper concentrates containing high amounts of arsenic and antimony by a smelting process is difficult due to environmental implications of toxic arsenic and antimony. As demand for copper continues to grow, the need to source copper from several types of resources including those that contain high levels of As/Sb becomes necessary. Therefore, a novel processes for the treatment of As/Sb bearing Cu concentrates are required. Reviews on copper resources such as enargite, tennantite and tetrahedrite containing high amounts of arsenic and antimony are covered widely in literatures by many researchers (Padilla et al., 1998; Welham, 2001; Vinals et al., 2003; Guo & Yen, 2005; Balaž & Achimovicova, 2006a; Filippou et al., 2007; Mihajlovic et al., 2007; Lattanzi et al., 2008)."

Jan 1, 2016

By L. Shang

In conventional continuous hot rolling processes, metals are usually reheated to a temperature such that the workpiece will maintain appropriate hot working characteristics as it proceeds through the rolling mill, assuming that the temperature is continually decreasing. Metallurgically, reheating will reduce micro-segregation in the as-cast material, may increase the as-cast grain size and will affect any second phase particles present in the as-cast structure. All these changes can affect the hot working characteristics, and the final as-hot rolled microstructure. In order to study the effect of reheating on AZ31 magnesium alloy, a plate sample was cast in a water cooled copper mould and a series of compression tests was performed at a temperature of 350 °C, strain rate 0.01 5-1, and strains from 0.2 to 1.0, after different reheating schedules. It was found that there is no significant difference in flow behavior between the as-cast sample and all but one of the reheated ones. The reheat treatment of the 'anomalous' sample was a two stage heat treatment; it was first reheated to 450 °C, cooled to room temperature, then reheated to 350 °C. The effect on the flow curve was to increase the flow stress. This result may be related to changes in second phase particle characteristics.

Jan 1, 2006

By Rick J. Chalaturnyk

In Alberta, oil sands bitumen is utilized for synthetic crude oil production by surface mining, bitumen extraction followed by primary (coking) and secondary (catalytic hydrotreating) upgrading processes, or by catalytic hydrocracking and hydrotreating replacing the primary and secondary upgrading processes. Oil sands tailings, composed of water, sands, silt, clay and residual bitumen, is produced as a byproduct of the bitumen extraction process. Several processes have been proposed for the treatment of oil sands tailings, resulting in different recovered water characteristics, consolidation rates and consolidated solid characteristics, which may have effects on the performance of the overall plant operations. A process for the same purpose has been developed by treating the oil sands tailings with CaO lime and CO2 and thickening it using a suitable thickener. In this process a release water of acceptable properties is recovered in a short retention time, which makes it possible to recycle the recovered water, probably after a reconditioning treatment, as warm as possible to improve the thermal efficiency of the extraction process. The paper presents the theory and laboratory results for the CaO and CO2 thickening of low temperature flotation tailings. The water release rates, segregation potential of the thickened underflow and chemistry of the release water are shown and discussed. It is suggested that in using the proposed process, the thickened tailings underflow can be disposed for further consolidation, or combined with the coarse tailings to produce Blended Composite Tailings, corresponding to the Composite Tailings process in the existing hot water extraction plants.

May 1, 2002

By T. G. Carter

"During the early part of the 1980s, four new surface coal mines commenced operation in the Province of British Columbia. Each represented a major investment in both persons and materials in order to protect this investment in one significant area-the fixed portion of the surface coal handling system-a substantial amount of work was undertaken to ensure that the system was well protected from an outbreak of fire. A great deal of effort in this field had already been made by those coal mines which had been in operation for a number of years and experience gained at these operations was utilized in determining the level and extent of fire protection for the new mines.This paper summarizes the major problems, and suggests some of the methods of solution, in providing an adequate degree of fire protection for surface coal handling systems. It will also discuss the potential for gas and dust explosions together with ways to minimize this potential.The Fixed Coal Handling SystemNote: The word ""fixed"" has been used in its present context to denote that part of the coal handling system where the coal is moved via fixed installations such as a conveyor. It differentiates from that part of the system where coal is moved by mobile equipment.The raw coal delivered to the truck dump will undergo two major processes on its way to the rail load out. The first will be at the coal preparation plant where coal of specified quality will be extracted from the raw feed to the plant. If this coal is of metallurgical quality, and sometimes if it is of thermal quality, it will pass through a thermal dryer where part of the moisture acquired during coal preparation will be removed, i.e. the second process. As the complexity of both the coal preparation plant and the thermal dryer is such as to warrant separate considerations they will not form part of this paper. Each of the processes, however, is generally, housed in its own building, thus, containment of any hazards is usually more attainable than those existing or caused in the rest of the system."

Jan 1, 1988