Search Documents

By J. Q. Chen

The elastic-plastic behavior and the fracture mechanisms of two 2198 Al-Cu-Li thin sheets are investigated. The first material (2 mm thick) is in a recrystallized state after cold rolling. The second material (6 mm thick) is hot rolled and has a fibrous grain structure. The two materials are studied in both T351 and T851 conditions. Tensile tests are carried out along different sheet directions using flat and notched specimens. Fracture resistance was characterized using Kahn tear specimens and M(T) panels. Macroscopic fracture surface of smooth tensile specimens depends not only on testing material but also on the loading direction. For Kahn tear specimens, fracture is initiated in a small flat triangle whereas slant fracture is observed during crack propagation. Fracture mechanisms were investigated using scanning electron microscopy (SEM) and X-ray 3D tomography.

Jan 1, 2011

By C. O. Swanson

THE purpose of this paper is to discuss the use of the dip needle in the field of mining geology. The subject matter is new only to the extent that it reflects the writer' s added experience in recent years. The treatment is brief, and those interested in a more extended analysis are referred to the articles listed at the end of the paper. In the discovery and tracing of mineral deposits, the clip needle, like most other geophysical instruments, can be used in two ways. One method may be termed direct; the other, indirect. The direct method is that of finding or following certain ore-bodies by virtue of their magnetic properties. Explicitly, or by inference, it is the method which many mining men and practising geophysicists have in mind when they consider whether or not a certain property should be studied by geophysical means. In the ideal case, this method demands little or no knowledge of geological conditions. The indirect method uses the clip needle as an aid to purely geological studies in working out the structure of a mineralized area. Although not as simple as the direct method, it enjoys a much wider field of usefulness. The writer's experience in the past fifteen years, which is believed to be typical, is that the indirect method finds application four or five times as often as the direct method. The indirect method is of particular value because it furnishes information concerning the relationship between geological structure and ore occurrence. Most mining engineers will agree that structural control is an important factor in the localization of ore deposits, and therefore that the subject under consideration is of some interest in mining geology. Specifically, then, the present purpose is to outline the principles and practice of using the clip needle in working? out geological structure.

Jan 1, 1941

By H. Staton, XPS Consulting & Testwork Services, T. Deng, M. Kelvin

"Lundin Mining’s Eagle Operation, located in Marquette County, northern Michigan consists of a mine and concentrator that processes a Ni-Cu-(PGE) ore. Mine production began in 2014 and is expected to achieve production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year. The ore is trucked to the Humboldt Mill, where both a Ni and Cu concentrate is produced.XPS Consulting & Testwork Services (XPS) has assisted the team at Eagle since 2013. Prior to start up, the ore was piloted at the XPS lab in Sudbury, Ontario to demonstrate the concentrator flowsheet and establish flotation operating strategy. XPS consulting metallurgists worked closely with the Eagle team during the commissioning of the plant providing troubleshooting, sampling, metal balancing expertise and support. Finally, a series of monthly composites over a 6 month period was submitted for mineralogical characterization to assess plant performance, identify opportunities for improvement and to provide a baseline for the future operation.Lundin’s investment to test the ores ahead of mining and to team with XPS’s experienced mineral processing engineers to help commission the plant has led to the plant achieving concentrator production targets shortly after startup. The commitment to training and implementation of best practices, and a culture where ongoing testing is the norm, puts the Eagle Operation on sound footing for future operation.INTRODUCTIONLundin’s Eagle Mine is a subsidiary of Lundin Mining located in the upper peninsula of Michigan. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 2 hours to the Humboldt mill.The ore is an ultramafic hosted high grade Cu Ni deposit and exists as either massive or semi massive sulphides. The high resource grade of Cu (2.49%) and Ni (2.93%) make this a valuable ore source. (Owen & Meyer, 2013) A metallurgical team was put together by Lundin to ensure the mill was designed and commissioned to optimize metallurgy in the shortest time from this valuable deposit. The commissioning plan targeted commercial production by Q1 2015."

Jan 1, 2016

By Mario E. Rossi

Geostatistical conditional simulations are becoming increasingly popular as tools that provide models of uncertainty at different stages of a mining project. They have been used as grade control tools in daily operations, to assess the uncertainty of minable reserves at the project?s feasibility stage, and to assess mineralization potential in certain settings. Other applications include assessment of recoverable reserves, resource and reserve classification, and drill hole spacing optimization studies. All large-scale applications of conditional simulations intend to benefit from the ?correct? (or ?accurate?) characterization of uncertainty, adequately describing the variability observed from the data and its impact on the final objective. The objective of this paper is to compare the ad-hoc ?uncertainty model? provided by a traditional classification scheme with the probability intervals resulting from a conditional simulation model. It is argued that the uncertainty model derived from the use of classification schemes is of little practical use to the mining company or operation. The paper emphasizes differences in uncertainty based on the size of the mining unit considered and the extraction method, and local geological differences. Most importantly, it discusses confidence intervals for these mining units, as compared to the relative precision envisioned by a typical classification scheme. The application described in this paper is taken from a medium-sized Cu open and underground mine in northern Chile, and it demonstrates the impact of several variables on the resulting conditional simulation models. It also compares a more ?traditional? resource classification scheme applied, and the wide difference in local confidence intervals for each mining unit.

May 1, 2001

By D. C. Fraser, W. J. Scott

"Airborne electromagnetic surveys were flown during 1965 in the Moose River area of Ontario. The systems used were INPUT Mark II and the Canadian Aero Otter. Anomalies indicated by both systems were located on the ground with vertical-loop EM. Two such anomalies were drilled, with no explanation being found in the bedrock geology. Subsequent seismic, resistivity and gravity surveys indicated that the sources of these anomalies lay in the overburden. Current work in the similar geological environment of the Winisk River area has shown that comparable AEM anomalies can still be misleading. The lesson to be, learned from these experiences is that additional geophysical work can help to resolve doubtful cases before drilling decisions are made."

Jan 1, 1973

By M. N. Vu, G. Armand, A. Noiret, D. Seyedi

Extensive experimental observations have been performed around drifts and shafts at the Meuse Haute-Marne (North-Eastern France) Underground Research Laboratory (URL) to assess the extent and pattern of the induced fracture networks in Callovo-Oxfordian claystone. Two types of fractures can be distinguished, namely; shear (mode II) and extension unloading (mode I) fractures. The main goal of the present paper is to provide insights on the extent of damaged zone around the drifts by numerical simulations. A two-step approach is considered. First, 2D elastic calculations are performed for simulating the excavation of a drift following the direction of the major in situ horizontal stress. The evolution of the stress and strain tensors around drifts are calculated by applying an elliptic convergence function on the drift wall. Two failure criteria are then verified for the induced damage. An equivalent strain and an elastic energy based damage criteria are considered. The obtained results show that the employed simplified approach provides rather good results for the extent of the damaged zone for drifts parallel to major horizontal stress. However, post-processing elastic results leads to overestimating the vertical extent of the damage zone and underestimating its lateral extent, where the in situ stress state is quasi-isotropic in a section of drift. Nevertheless, the obtained results show that an energy based damage criterion could be considered as a potential way for reproducing the extent of the damaged zones if a convergence function can be defined for the drift.

Jan 1, 2015

By Robert B. Parsons

"In this period of improved metal prices and reported profits, valuable lessons should be recalled from the 1970s when a similar cycle lured the federal and provincial governments into thinking that they could grab bigger pieces of the pie without harming the minerals industry. It took years for the industry to recover from the damage inflicted by that unprecedented scramble for higher tax revenues. It is hoped that the current policy makers will have learned from the lessons of the seventies, and will realize that mining companies need to keep a reasonable share of profits realized during the good years in order to prepare for the inevitable downturn in the cycle.INTRODUCTION"", «. We have made clear to industry that super profits... will no longer be tolerated "".With that assertion, the Honourable David Barrett , Premier and Minister of Finance of the Province of British Columbia, announced the introduction of a new mining tax regime in his February 17, 1974 bud get papers . British Columbia producers would face a basic royalty and a royalty on so-called ""super profits"", resulting in some instances in tax rates exceeding 100070 of pre-tax profits.The ball started to roll. Mining tax changes knew no political or geo graphical boundary. On April 9, 1974, Ontario's Treasurer John White stated in his budget speech:""Increased demand by major industrialized countries has resulted in sharply higher metals prices and substantial wind fall gains for the mining industry in Ontario. With the prospective demand for minerals likely to sustain current price trends into the future, it is only fair that we secure for the people a higher return from our natural resources""."

Jan 1, 1989

By M. A. Perras, H. A. Kasani, G. Walton

The development of an underground repository for the storage of spent nuclear fuel relies on a multi-barrier system to isolate the used fuel from the environment – ultimately, the biosphere. These barriers include engineered copper and steal canisters, dense bentonite, and the natural rock as well. In order to reduce the potential flow pathway along the excavation induced damage zone, various slots perpendicular to the excavation axis have been proposed. These slots are called cut-off seals and generally are filled with bentonite as it has high swelling potential and very low permeability. Many different geometries have been proposed, but clear guidelines on the selection of the optimum geometry have yet to be developed. In order to assess the optimum geometry, three shapes have been selected for this numerical study, including a trapezoid, a triangle, and a thin rectangular slot. The cut-offs were modelled for a conceptual shaft constructed in the Queenston Formation from Ontario over a stress to strength ratio that has been found at many underground research laboratories. It was found that the excavation of a triangular and thin slot cut-off had the smallest increase in the damage as quantified based on the extensile volumetric strain within the plastic yield zone. Both shapes showed an increase in the damaged zone by 13 cm at a stress to strength ratio of 2.75. The trapezoidal cut-off damage zone increased by 20 cm at the same stress to strength ratio. Further study is required to better define the optimum cut-off shape for wider variety of conditions and other geological formations.

Jan 1, 2020

By L. Tafaghodi, A. Hosseinpour

"Silicon is considered as the most appropriate semiconductor material for manufacturing solar cells because of its natural abundance and being nontoxic. The transferable knowledge and technology from the electronics industry and the long history of silicon-based semiconductors are also assisting the domination of silicon as the most common semiconductor material. Developing an environmentally and economically viable process for producing solar grade silicon has been one of the main challenges in the silicon industry in the past few years. Metallurgical refining processes have received significant attention because of their high productivity and low cost. Slag refining is one of the purification methods which is based on oxidation of the impurity elements, followed by its dissolution into a slag phase. This article presents a review of various slag refining processes that have been employed for purification of silicon and silicon alloys. SiO2, CaO, CaF2, CaCl2, Al2O3, MgO and Na2O are the major components of the slags used for silicon refining. These slags can be classified into three main categories including binary, ternary and quaternary slags.INTRODUCTION Silicon can be categorized into three different grades based on its application or purity: metallurgical grade silicon (MG-Si) with purity of ~98 %, solar grade silicon (SoG-Si) with purity of ~99.99999 % and semiconductor grade silicon (SeG-Si) which has the purity of 99.9999999 % (Johnston & Barati, 2010; Krystad, Tang, & Tranell, 2012; Tang, Øvrelid, Tranell, & Tangstad, 2009). Producing SeG-Si is carried out through an energy-intensive and complicated process named Siemens. This purification process is relatively slow and involves using toxic and corrosive reagents (e.g. Trichlorosilane). At present the majority of SoG-Si is produced via Siemens or Siemens-like processes and there is very limited production via processes dedicated to SoG-Si. Because of the difference in silicon specifications required in microelectronics and photovoltaic industry, and the cost and energy associated with the Siemens process, an interest has emerged to develop technologies dedicated to producing low cost SoG-Si (Istratov et al., 2003; Johnston, Khajavi, Li, Sokhanvaran, & Barati, 2012; Mitrašinovic, D'Souza, & Utigard, 2012; Wu et al., 2012)."

Jan 1, 2017

By Randy Billing, J. Fraser Wilson

"IntroductionThe job of designing and implementing effective environmental management sounds like what one executive, assuming responsibility for a very sick organization with lots of potential described as, ""an insurmountable opportunity"".Effective environmental management is an opportunity, no doubt. Its an unusual, if not unique opportunity. Insurmountable? Maybe not! Indeed, in the authors' experience, the keys to unlocking this opportunity are not in new or complicated technicalities; they are in the existing strengths and successful experience that one has in managing other complex and exacting management issues.To begin, it is necessary to understand what these issues of sustainable development mean to business. What is the nature of this opportunity? What makes it look unsurmountable?New Games: New RulesLawyers have described some of the new rules companies are facing and there is a new game being played; a game characterized by unique challenges.Take two, for example: • The ecological problems to be faced are Mother Nature's business, the political solutions required are our business. This combination of natural problems and political solutions requires the development of new management mechanisms, to bridge the gaps among us, as individuals, as professions, as interest groups and so on; indeed, even as countries;• and gaps there are : about as many gaps as the people involved : many of them with new and changing expectations, often mutually exclusive and not negotiable.The challenge of these relationships and communications among so many different interests is one of the keys to effective environmental management.Like any game, this one has rules and they are new, too. These rules are evident not just in new legislation - tough legislation with draconian penalties; they are also evident in new and exacting business policies, value driven and just as unforgiving of poor performance. Senior management of many companies are speaking about the role of enlightened corporate policies and how important it is for everyone involved that these policies drive and reflect business practices. Absence of day to- day behaviour which evidences the words in action, the policy on the wall of a corporate office or published in an Annual Report is first evidence for the prosecution , not the defence.The challenge of practical policies is another key to effective environmental management.This is a new game, with new rules: the challenge of change."

Jan 1, 1991

By C. E. Lancelle, J. T. Volk, H. F. Wang, D. Fratta

"The Main Injector Neutrino Oscillation Search (MINOS) Near Detector Hall at Fermilab and the Lafarge – Conco Mine are located approximately 100 meters underground in the Galena-Platteville dolomite just below its contact with the overlying Maquoketa shale in Northeastern Illinois, USA. A new cavern was excavated adjacent to the MINOS Near Detector Hall at Fermilab to house the near detector for the Off-axis Neutrino Appearance Experiment (NOvA) program. During this excavation approximately 1150 cubic meters of shale rock were removed. Tiltmeter arrays consisting of a series of hydrostatic leveling sensors (HLS), which are spaced regularly over a total distance of 50-to-100 meters, were used to monitor subsurface deformations. The tiltmeter response in the MINOS Near Detector Hall due to the NOvA cavern excavation is approximately thirteen times the estimated response based on using laboratorydetermined properties. The discrepancy between modeled and measured tilt is likely due to differences in Young’s Modulus in the rock mass versus in a small laboratory sample. Amplitudes of measured solid earth tides differ from the amplitudes of theoretical solid earth tides by up to 40 percent for both arrays. This is likely due to a local heterogeneity or discontinuity.INTRODUCTIONLong baseline tiltmeters have been used to record small earth movements since the early 1900s. One of the first studies using long baseline tiltmeters to measure earth tides was published by Michelson (1914). He used a leveled 152-meter long, 0.15-meter diameter tube half-filled with water connecting two concrete-lined pits. The pipe was trenched 1.75 meters underground in Williams Bay, Wisconsin in a sandy-clay soil. Initially only an east-west line was used, though a north-south line was added after it was seen that viable results were obtained. Measurements were made by hand either hourly or once every two hours depending on the time of day. When compared to 0.7 times the calculated earth tides, the tiltmeter signal matched almost exactly. This excellent result began the use of long baseline tiltmeters to measure small earth movements."

Jan 1, 2015

By V. K. Karra

"A simplistic algorithm jar simulating the rod or ball mill Bond grindability test applied to ores and minerals is presented. A performance comparison between the present algorithm and a previously published algorithm by Kapurot, modified in this work jar a fair evaluation, is also given. A worked example is furnished jar leading the reader through the various calculations.IntroductionThe Bond grindability test is widely used for the prediction of the power requirement of an industrial grinding mill. The procedures for conducting this test in either a ball or a rod mill are available(1). In the case of a ball mill, batch grind abilities have been correlated to Bond grindabilities to help monitor day-today variations in ore grindability for the purpose of plant control( 2,3). Of special interest is the algorithm presented by Kapur(3) for the simulation of the Bond test. In practice, the test lasts from 6 to 14 cycles (4 to 10 hours). With this algorithm, one can predict the Bond grind ability using information available from only the first two cycles.Sometimes the prepared feed for the grindability test contains too much fines compared to the total product desired at the mesh of grind under consideration. In such a case, the operator separates the fines from the test feed and adds to the remaining coarse fraction an equal amount of fresh feed. This combined feed then forms the feed to the first cycle of the test. In the present work, Kapur's algorithm is modified to include this special case. A new and relatively simpler algorithm is also presented. Statistical equations relating work index to pertinent variables are also given."

Jan 1, 1981

By J. G. Whellock, J. W. Matousek

"In spite of their importance to the economics of many metallurgical projects, the values and technical aspects of precious metals losses in smelting operations are relatively undeveloped subjects. This paper attempts to provide a condensed overview of precious metals losses in pyrometallurgy, using some of the limited production and experimental data available. It is intended for three general groups of metallurgists - operators attempting to improve recoveries, cost-accounting engineers making estimates of metal losses in new or modified smelting plants, and research engineers and students.Distribution coefficients of precious metals, the ratios of metal or matte assays to slag assays, are convenient means of comparing smelting processes and the tendencies of the different metals to enter the slag. For silver in lead blast furnaces this ratio is approximately 250;for gold and the platinum group metals in submerged-arc, electric furnaces it is 900. The ratio for gold and PGMs in converters varies with the degree of oxidation of the charge. The over-all cycle-average for industrial installations is tentatively estimated to be 35.IntroductionThe magnitude of precious metal s losses in pyrometallurgical operation s is difficult to assess. The primary producers are generally reluctant to discuss the subject. The by-product producers (the large sulphide smelters o f copper , nickel, and lead) might be more willing to disclose information, but these have precious metals in their feeds in such dilute quantities that accurate accounting is extremely difficult. It is not until numerous processing steps have been taken t hat the precious metals become sufficiently concentrated to permit acceptably accurate sampling and analytical procedures to be followed. Thus, knowledge of the precious metals contents o f the intermediate mattes and slags may simply be unavailable."

Jan 1, 1990

By F. Vagnon, A. M. Ferrero, M. Pirulli, A. Segalini

"The topic of this study is the design of flexible fences to mitigate the risk due to debris flow phenomena by means of theoretical and experimental studies analysed in framework of the Rock Engineering System (RES).The study of the interaction between debris flows and flexible barriers is a major challenge since many different aspects concerning both the slope characteristics and the structure features are involved. Debris flows are often triggered by the mobilization of debris deposits that are generated by rock fall of adjacent rock walls. The rock debris deposits are difficult to be characterized by the physical and mechanical point of view due to their large variability in volume distribution and, moreover, when dealing with high mountains environment, they are also strongly affected by the presence of water at different phases (solid or liquid) depending on the temperature. The debris deposit turns unstable in relation with the geotechnical and environmental features of the areas and the instability evolution in high mountain steep valley is often a debris flow. Debris flow destructive potential is very high and protections are often needed to reduce the debris flow risk.This complexity determines the needs of comprehensive study able to include the global basin dynamic and the environmental conditions. An a-priori analysis of the influence of the different aspects can be useful to focus on the real driving aspects of the problem. Due to the complexity of the system the application of the RES methodology is recommended in order to clearly define the different assumptions needed, their influence on the simulations and a comparison among them.RES allows investigating triggering criteria, flow and depositional processes and interaction of flows with protection fences in a rational way. For this purpose, an interaction matrix is created: it summarizes the key geotechnical parameters that influence debris flows, their interactions and debris/engineering protection opera behaviour. The goal is to quantify the diagonal-off terms to assess the residual risk after barrier construction, using back analysis from real debris flow event and data collection from literature.This methodology is applied to analyze a debris flow event in the Italian Western Alps where numerical analyses are carried on to assess flow characteristics to be used for fence design through the application of an analytical and numerical model developed by the authors (Brighenti et al, 2013). In particular, the velocity and deposition heights have been estimated using the numerical code RASH3D (Pirulli, 2010), which is a single-phase model based on depth-averaged Saint Venant equations. Pathways of different lengths are studied to assess the input data necessary to design the protection barrier and to determine the associated risk. Simulation of the barrier at different places along the valley will also allow to determine optimal barrier location in terms of minimum residual risks by comparing the velocity, the volume and the energy of the debris after the barrier impact.The work will produce a possible design scheme to be adopted in this environment."

Jan 1, 2015

By B. D. Pandey, M. S. Kim, B. S. Kim

The recovery of Sn from used Pb-free solder (Sn, 3~4 % Ag, < 0.9 % Cu, < 1.2 % Pb) has been investigated by electrorefining in sulfuric acid solutions containing small amount of hydrochloric acid. This involved preparation of the anode material by melting and casting the used solder followed by refining. During electrorefining, dendritic tin was deposited on stainless steel cathode. Increasing the amount of hydrochloric acid up to 0.3 mol /L in the electrolyte enhanced the current efficiency to 92.2 % and the enrichment ratio of silver to 94.3 % in the anode slime which was otherwise 84.7% and 81.6 % in absence of HCl, respectively. The electrolyte containing hydrochloric acid has also prevented the precipitation of tin oxide in the bath. In the scale-up experiment using 1.6 kg anodes, 84.3 % current efficiency and close to 100 % Ag enrichment ratio were obtained, while the purity of electro-refined tin was over 99.9 %. The energy consumption of the winning process was found to be 0.151 kWh /kg-Sn which is competitive as compared to commercial tin electrorefining processes.

Jan 1, 2014

By I. Lazaro Roche, J. Brunner, J. Busto, X. Martin, J. B. Decitre, S. Gaffet, F. Hivert

"Muon tomography allows investigating the subsurface. Muons being penetrative, the attenuation of the muon flux depends on the quantity of matter the particles travel through, hence on the rock density and thickness. For the Temporal Tomography of rock Density using Muon Measurements (T2DM2) project, the muon flux measurements are performed in LSBB URL (http://www.lsbb.eu) in order to study the hydrogeological processes in the unsaturated area of Fontaine-de-Vaucluse karst aquifer. The suitability of the muography for this study is here numerically demonstrated. In parallel to these simulations, muon flux measurements are carried out in the LSBB galleries by means of a set of four scintillator tanks and Micromegas detectors are developed. These detectors, here described, are adapted for underground and confined spaces as well as other environments. Their performances are particularly interesting and should contribute to the expansion of muon tomography in new application fields. INTRODUCTIONMuon tomography or muography is a method to image large volumes by measuring the absorption of cosmic ray muons. It uses, in a passive way, a natural radiation source: the muons which are charged particles produced in the atmosphere. Primary cosmic rays interact with atmospheric nuclei and produce a huge number of secondary particles, including muons. Due to their important mass compared to electrons, they are highly penetrating, reaching several hundreds of meters below the surface. Their attenuation depends on the quantity of matter they cross. That's why they are used to investigate the subsurface, muon absorption measurement allowing to estimate the in-situ density of the rock.Georges (Georges, 1955) proposed in 1955 to use the muons in order to study the density variations caused by the overburden over an Australian tunnel. In 1970, Alvarez (Alvarez, 1970) imaged the internal structure of Chephren Pyramid thanks to this method. The muon tomography has been particularly developed for volcanology (Nagamine, 1995; Tanaka, 2007; Lesparre, 2010; Carloganu, 2013) over the last twenty years. Since the beginning of the 2010's, a growing amount of projects that proposed to use the muons in various fields get underway: the CO2 storage (Kudryavtsev, 2012), the exploration of Mars (Kedar, 2013), etc."

Jan 1, 2015

By Ernest A. Hodgson

A SERIOUS hazard which must be faced in some mines, though quite absent in others, is that of rockbursts. Bursts cannot be wholly avoided in such mines, but the hazard would largely disappear if they could be predicted. The problem of prediction resolves itself into that of measuring pressure in the mine and determining when that pressure nears a critical value. The geophysical approach to the problem lies in discovering some physical property of the rock, which varies with pressure, which can be measured for rock in place, and for which the indication of critical conditions is sufficiently definite and open scale. A physical property, suggested first in connection with earthquake pre-diction, is that of sub-audible snapping. It was argued that, as the pressure grows, the rock probably yields microscopically and that minute snapping occurs which is so faint as to be inaudible to the unaided ear. Experience has proved this to be the case. Following other earlier work begun early in 1939, experiments with this method were initiated at Lake Shore Mines in 1941, and equipment was slowly being developed in practice when, fortunately, it was found possible to by-pass this tedious development programme. Experiments with sub-audible snapping in mine rocks had been carried out by Dr. L. A. Obert of the U.S. Bureau of Mines and his associates over a period of about four years. An amplifier and a recorder were developed, each reasonably satisfactory in practice. Lake Shore Mines offers a tempting field for rockburst research. Dr. Obert was invited to test his equipment in this and other mines in Ontario and did so. As a result, he and the administrative personnel of the Bureau became interested in the Lake Shore experiments co the extent of most generously arranging for the manufacture of sets of their own designed equipment for use in this programme. The first three sets of recorders were ordered at once and were delivered in May, 1942. A second group of three sets, incorporating various improvements indicated by experience both in the United States and in Canada, reached Kirkland Lake in April, 1943. The pick-up devices, known as geophones, were made in the electronics laboratory at Lake Shore by Mr. Zack Gibbs, who has had charge of all the instrument development in this re-search.

Jan 1, 1943

By D. S. Harries, R. I. L. Guthrie

"The use and development of scientific disciplines involved in heat transfer technology, related in general to steel masses and in particular to batch annealing, is demonstrated.The measurable benefits of cooperation are tabled; on industry&apos;s side, this includes a 10 to 20 per cent decrease in annealing time, and a corresponding higher productivity potential. The returned benefits to the academic engineer include the development and refinement of new computer algorithms related to heat transfer mechanisms.IntroductionThe object of this discussion is not really to describe an improvement in the batch annealing operation, but to use the project as an example of joint work between industry and the academic field. Both parties have derived a number of substantial benefits. These benefits will be listed, of course, but the batch anneal project will be used just as a typical example of cooperation. Why it happened will be explained, what actually happened will be described and finally some thoughts about areas in the field of heat transfer, where cooperation will continue in the future, will be highlighted. The paper will close with a message.Industry OverviewAt the outset, perhaps it should be understood that, in general, the Research Department at Dofasco believes that the universities and their staff are not destined for the problem-solving role in industry. Its opinion is that the university staff is best suited to the gathering and dissemination of knowledge. There are other more professional problem solvers for industry, including the steel industries&apos; own individual investigation groups. Dofasco, therefore, looks to its academics for consultation. It benefits by bouncing ideas off them, and through rubbing shoulders with them in such a way that their knowledge can be tapped, and thus establish more effective scientific routes. In addition, the younger and brighter engineer s can broaden their scope through the intellectual contact with experts. The university professors can, it is believed, benefit through closer contacts with result-orientated research. They can also develop an appreciation of the fiscal control necessary for industrial investigations, without government subsidies, grants, etc., and with massive overheads."

Jan 1, 1982

By F J. Pearce

The Steel Company of Canada, utilizing the S-L process, has produced partially and highly reduced pellets for use in the blast furnace. Experimental blast furnace tests, using reduced pellet burdens, have been carried out. The changes in production rate, fuel rate and general performance of both the S-L and the blast furnace processes are indicated. Introduction T HE ore burdens for a blast furnace may be improved in two ways: chemically, by concentrating the ore to a high degree of purity; and physically, by agglomerating or closely sizing the ore particles. Today, many b1ast furnaces are charged with closely sized agglomerates, some of which contain upwards of 66 per cent iron. The further improvement of these burdens by chemical concentration may, in many instances, be uneconomic due to the large losses of iron that occur during processing. Assuming that it would be possible to reject all of the gangue minerals, the maximum level of concentration of iron in the hematitic ores would be only about 70 per cent.

Jan 1, 1964

By Corby G. Anderson

"Laboratory testing using industrial electrowinning solutions was performed to determine the best Faradic cell efficiency for copper cathode recovery. The variables tested were solution flow rate, recycle ratio, reagent addition combinations of guar and thiourea, and addition amount of acid mist suppressant CAL FAX DBA-70. The ideal flow rate was determined to be 37.85 litre/min. Additionally, the ideal recycle ratio was determined to be 10:1. The reagent addition scheme from testing which showed the highest efficiency was with 680 g/tonne guar of cathode copper won and with 135 g/tonne thiourea of cathode copper won. These values for reagent addition only reflect the best efficiency and should not be assumed to be the best reagent concentration for copper purity. The amount of foaming agent that showed the best efficiency was the test with 2 ppm of foaming agent. Again this amount of reagent is based on efficiency and should not be taken as the amount of reagent that does the best acid mist suppression. Additional proprietary surface characterization work indicates these additives may have enhanced the cathodic reduction surface morphology of some noble minor impurities. Subsequently, these operating parameters were introduced into the plant operation and proved successful after their implementation.BACKGROUNDCopper electrowinning has become a dominant technology for the production of marketable high grade copper cathode products. The literature is robust with applications, optimizations, additives and developments in this field (e.g., Classens & Harris, 1990; Pfalzgraff, 1999; Tozawa, Su, & Umetsu, 2003; San Martin, Otero, & Cruz, 2005; Houlachi, Edwards, & Robinson, 2007; Romero, Avila, Fester, & Yacher, 2007; Marsden, 2008; Beukes & Badenhorst, 2009; Vainio & Weatherseed 2009; Bender, 2010; Joy, Staley, Moats, Perkins, Uhrie, & Robinson, 2010; Khouraibchia & Moats, 2010; Moats, 2010; Rutledge & Anderson, 2015).Tests of forty hours duration and at room temperature were performed for this project using samples of actual industrial electrowinning solutions. These industrial solutions were comprised of 60 g/L Cu plus 65 g/L Ni, 3 g/L Fe, and 30 g/L free sulfuric acid. Other confidential minor impurities were also present including some solubilized precious metals. The testing apparatus utilizing stainless steel anodes and cathodes is illustrated in Figures 1 and 2."

Jan 1, 2016