Search Documents

By Mory M. Ghomshei

"The cost of deep underground mine cooling depends on a number of geological, environmental and economic factors such as the temperature gradient in the mine, the outside air temperature, and the local price of energy. While geological factors, being static, can be controlled to some extent during the mine design, the environmental and economic factors dynamically change and therefore can only be controlled through a flexible mine ventilation system.With an average temperature gradient of 20–25°C/km, the virgin rock temperature at 2,000 m can reach 45–60°C. Conventional cooling at such depths could lead to exorbitantly high costs. In-mine geothermal heat pumps can considerably reduce the cost of cooling through energy communication with the centralized absorption chillers, which service the mine from the surface.It is shown that in-mine heat pump systems can be a viable option for reducing operating expenses and providing some degree of flexibility to cope with fluctuating energy costs. The price of Natural gas and electrify are the most important variables for optimizing the level of interaction between the surface and inmine cooling systems. Deep mine waters can be used to carry a portion of the mine heat to the surface, where the heat from mine can be used as a supplementary energy source for absorption chillers. As an extra benefit, the heat output of the chillers can be used for district heating and or greenhouse growing.The case of cooling deep levels of deep mines in Sudbury Canada (e.g. Creighton Mine) has been discussed. It is shown that an initial 1MW in-mine geothermal heat pump system can save significantly on the cost of cooling. Such a demonstration project will allow R&D on viability of larger similar systems to be incrementally added in the future.INTRODUCTIONThe amount of heat generated in deep and ultra-deep mines depend primarily on the regional temperature gradient and the thermal conductivity of mine rocks. The conductive heat flow is quantifiable and can be minimized or optimized in the process of mine design. Another important heat source can be related to underground equipment such as diesel machinery which often have low efficiencies (approximately 25–35%). This heat source can be controlled and reduced though improving efficiencies or using electrical equipment, which offer a much better efficiency (approximately 80–90%). Mine waters can also be a significant heat source (convectively bringing large amounts of heat into the mine workings)."

Jan 1, 2019

"RÉSUMÉOn discute les principales sources de dilution au cours d’une exploitation souterraine. Les différentes définitions de la dilution en usage sont analysées. Une nouvelle méthodologie de calcul simplifiée et facile à utiliser dans la pratique minière est présentée. Cette méthodologie permet de remplacer les différentes expressions analytiques en usage par les deux facteurs de dilution seulement : un «facteur de dilution planifiée» lié à la sélectivité d’abattage au niveau de la planification minière et un «facteur de dilution additionnelle » permettant de juger de l’efficacité du contrôle de terrain et de la dilution pendant l’exploitation souterraine. L’application de cette méthodologie donnerait un outil nécessaire aux niveaux de la planification, du suivi des travaux d’exploitation et d’éventuelles études comparatives des coûts entre les différentes situations minières.ABSTRACTThe principal sources of dilution during underground evaluation and mining are discussed, then definitions of ore dilution currently in use are analyzed. These definitions vary depending on the authors. A new ore dilution evaluation methodology is proposed, replacing the ten different analytical expressions by only two: the planned dilution factor related to the stoping selectivity, done at the mine planning level, and the additional dilution factor related to the efficiency of the dilution control measures during stoping operations. The conclusion shows that the use of this methodology would be a definitive asset in planning, in stoping operations follow-up, and in future costs comparison studies between mining operations."

Jan 1, 2001

By Roy T. Bowles

This paper focusses on technological developments which occurred in the village of Deloro, Ontario between 1868 and 1919. These developments illustrate the manner in which improved metallurgical processes linked Ontario mineral resources to industrial expansion. Overview of Deloro The village of Deloro is in Hastings county, about 5 miles from the village of Marmora, the site of the old Marmora iron works and the more recent Marmoraton iron mine. In this area, the Canadian Shield meets the Great Lakes lowlands. The first settlement in the vicinity occurred in the 1820s and was associated with the Marmora iron works. Settlement grew around agriculture. Gold was discovered in Hastings county in 1868. Deloro - the name derives from gold - developed as a concentrated settlement in proximity to several gold mines and the related processing activities. By 1901, substantial smelting works were successfully producing gold and arsenic from local ores. The village was developing as a company town within the framework of benevolent paternalism. For reasons associated with markets and with local ore supplies, the Deloro mills were idle for a period beginning in 1902. Developments in later periods connected Deloro to world events. In 1903, silver was discovered at Cobalt, Ontario. By 1907, M.J. O'Brien, who owned mines at Cobalt, had purchased the Deloro works and was using them to process Cobalt-area ores*.

Jan 1, 1999

By Davis. B. R.

There are a number of hydrogen storage systems proposed for automotive applications. However, all of the current suggestions fall short of the DOE targets for storage density and volumetric density. The DOE has suggested that only through radically new ideas will a practical solution to hydrogen storage for automotive applications be realized. This paper provides some background in chemical hydrogen storage and discusses roadblocks to the implementation of some proposed technologies.

Jan 1, 2005

By J. Basi, D. F. Rucker

"A review of historic operating practices of the heap leach pads at the Los Filos Mine, Mexico, revealed periods of restricted cyanide addition, reduced leach time, and insufficient irrigation flow. These issues all led to the buildup of partially leached recoverable gold inventory within the leach pads. Drawing down this inventory represented an opportunity to bring value forward. This paper outlines the strategic initiatives which were implemented as efforts to accelerate the inventory drawdown, including geophysical mapping and pressure injection.INTRODUCTION Los Filos is a heap-leach operation located in the Guerrero gold belt in southern Mexico. Operational and hydraulic challenges at the Los Filos Mine have led to a buildup of gold in inventory within the leach pads. Operationally, periods of restricted reagent addition, reduced leach time, and insufficient irrigation flow have compounded over the last eight years, and resulted in significant inventory growth. Hydraulically, the leach pad has issues with low permeability and solution channeling due to the fines and clay content of the ore. The leach pad is storing high-grade pregnant leach solution (PLS) as perched aquifers above areas that are compacted and difficult to drain. These operational and hydraulic challenges made it particularly difficult to spatially predict the precise locations of the inventory build-up. Fortunately, the challenges at Los Filos are not unique to the mine, and others have taken steps elsewhere to reduce metal inventory through a program that targets areas for inventory drawdown. For example, Ghorbani et al. (2016) noted that a method of injecting barren reagent solutions, applied directly to specific areas of a leach pad to reduce inventory, was presented by Wan and Brierley (1997) and Wan (1997). Seal (2004; 2007), Seal and Jung (2005), and Seal et al. (2012) have put the injection methodology into practice in Nevada and Colorado gold mines with a technology called Hydro-Jex®. The goal of Hydro-Jex has been to supply reagents at a high pressure over a short duration, followed by periodical low pressure rinse periods to remove leached metal and resupply fresh reagent to the ore."

Jan 1, 2017

By M. W. Grabinsky, J. H. Curran

"Characterizing the spatial distribution of rock stresses is a challenge, especially in the geologically complex environments typically found at most metalliferous mines. Therefore, instead of focusing, specifically, on the task of making stress measurements, the engineer should instead attempt to develop a better understanding of the interaction between stress, mining geometry and rock mass behaviour. This paper demonstrates such an approach using a Canadian Shield hardrock mine case study, in which geomechanical models are used to relate stress, mining geometry, and rock mass properties to observed excavation response, and numerical modelling is used to better quantify this interaction.IntroductionUnderstanding how the mine geometry, field stresses and rock mass interact to produce the observed rock mass response to mining can be a significant challenge. Consider our present ability to quantify the basic geomechanical design input data. Mine geometry is normally quantified in more detail than is required for analysis purposes. Our understanding of rock mass strength and stiffness is far from complete, but established procedures do exist to obtain estimates of these parameters based on index and laboratory testing data and field mapping. Our ability to quantify field stresses is probably the most limited, in part because stress measurements are difficult and expensive to carry out, and in part because the stresses vary to an unknown degree from point to point within the rock mass. The engineer must, therefore, consider whether or not stress measurements are justified and, when they are, where the average stress state needs to be quantified and how many of which type of measurements will be required to determine the average stresses.Such was the case at Ansil mine, a massive sulphide deposit in hard rock located at a depth of more than one kilometre in the northern Québec portion of the Canadian Shield. The Ansil orebody was relatively rich, but small, with the potential for significant stress-related problems. As a result, geomechanical design had to be done carefully from the start – there would be little opportunity to modify the mining strategy once production had begun, and the economic consequences of stope dilution and rock mass instability would be severe. An extensive stress measurement campaign was carried out, but the determined stress magnitudes were unexpectedly low. The designers were, therefore, faced with a dilemma:"

Jan 1, 1997

By Joseph Carlston

With environmental regulations continuing to restrict the discharge of phosphorus from wastewater treatment facilities, traditional methods of phosphorus removal are proving inadequate. To achieve the phosphorus control necessary, a new coagulant used for phosphorus removal, cerium chloride, has been studied in several municipal and industrial wastewater treatment facilities that must meet a phosphorus discharge limit of 0.5 mg/L or lower. These studies demonstrated the high phosphorus removal capabilities of cerium chloride, with the results illustrating the ability for cerium chloride to reduce phosphorus to low concentrations in the effluent using a lower volume of product as compared to traditional coagulants, such as ferric chloride. This reduction is due to the unique ability of cerium chloride to remove phosphorus as cerium phosphate, whereas iron- and aluminum-based coagulants rely on adsorption and co-precipitation.

Jan 1, 2014

By Robert D. Brown

"The Conservative Government 's budget proposals brought forward on December 11, 1979 have been withdrawn, but they are far from dead. On the contrary, a number of those budget proposals, especially the ones which would close loopholes and result in other technical changes being made to the Income Tax Act, should be considered to be alive and well.It is not unreasonable to expect the next government, of whatever political persuasion, to reintroduce many of these technical changes in the next federal budget. For that reason, last December's budget may have offered an interesting preview of what the mining industry and other taxpayers can expect in 1980. It is quite possible that some of these changes may be effective as of the original dates announced in the withdrawn budget proposals.This month, ""Tax Notes"" reviews the main pro visions of Mr. Crosbie's December, 1979 budget, with a primary focus on the changes that would have affected the resource sector.It must be emphasized that all of the budget proposals discussed herein have been withdrawn, that none of them are law and that any actual changes in our tax rules will have to be dealt with by the new Parliament that will be assembled following the February 18 election. December 1979budget withdrawnThe federal budget proposals brought forward by Finance Minister John Crosbie on December II, 1979 were withdrawn as a result of the defeat of the Conservative Government on a motion of non-confidence in the House of Commons on December 13. However, it appears quite possible that at least some of the proposals may be introduced into Parliament at a future date, possibly with retroactive effect.In a press release issued by the Department of Finance, Finance Minister John Crosbie stated that if the Conservative Government is returned to power, it will reintroduce all of the measures contained in his December II budget.Mr. Crosbie stated that all of the income tax measures contained in the budget would be reintroduced, effective on the dates indicated in the Notice of Ways and Means Motion tabled on December II. Some of the more important measures in December II budget, and their effective dates as indicated in the Notice of Ways and Means Motion, are discussed below.The December budget had also introduced or increased excise taxes or duties on gasoline, wines, cosmetics and photofinishing. If the Conservative party is re-elected, these measures will be reintroduced with prospective effect (i.e . effective as of new dates to be announced in the new budget)."

Jan 1, 1980

By Robert F. Shurtz

This paper discusses and compares methods of statistical analysis of the information relating to the evaluation of an asbestos deposit. From a study of 10-ft. lengths of drill core, the separate effects of visual evaluation errors were determined, as well as the deviations between evaluators and the deviations produced by a slight displacement in the center lines of the check drill holes. The importance of careful statistical analysis of such information is stressed.

Jan 1, 1966

By M. O. Pekguleryuz, D. S. Aydin

The high temperature oxidation and ignition resistance of Mg-(0-6) wt% Nd alloys have been investigated via isothermal and continuous heating experiments conducted in air atmosphere. Alloy composition is observed to be effective in low levels (~ 0.5 %) in the ignition temperature (Ti) of the alloys; the Ti of pure Mg increased from 630 °C to 770 °C with 0.5 wt% Nd addition. However, no noteworthy improvement was achieved with further additions up to 6 wt% Nd. The initial microstructure was observed to determine the oxide structure on the surface due to the differing oxidation behavior of the phases (a-Mg + Mg12Nd intermetallics). It has been found that the formation of a Nd-depleted region at the subsurface due to extensive Nd oxidation at the oxide/intermetallic interface lowers the protective ability of the oxide scale.

Jan 1, 2015

By Keith Jones, Largo Albert

"Decelerometer testing of a rigid guide system in a mine shaft pro vides usefuI information to operating and maintenance people. High acceleration/deceleration rates can lead to high maintenance costs to bath conveyances and shaft and can also present an operating risk . Possible disastrous results in the shaft have been avoided by restricting the maximum conveyance speed until the shaft and/ or conveyance problems have been solved.The test instrument is a valuable aid especially during commissioning or updating of a hoisting installation. High acceleration/deceleration rates also lead to reduced hoist rope life. During the past fourteen years, a total of 15,000,000 feet of testing was performed in 74 assorted shaft compartments.Based on this experience, it is possible to establish acceptable conveyance maximum speeds provided that all other conditions in the shaft compartment are normal. The body of the paper will present examples of several tests made under actual operating conditions.IntroductionMore and more mine operators are recognizing the real value in the use of the decelerometer for determining the state of shaft guide alignment in their shaft compartments , not only during the initial mine start-up periods, but also on a regular basis while the mine is in production.Decelerometer testing, is a technique in which an accelerometer , commonly known as a decelerometer, is used for measuring conveyance acceleration/deceleration in a lateral plane. lts purpose is to determine the severity of shock loads produced by misaligned shaft guides. Testing is performed by mounting the instrument on the conveyance and operating the conveyance (empty and loaded) at various speeds up to and including full speed . However, full speed may not be attained due to conditions indicated by the tests. These conditions may present an operating risk to the plant."

Jan 1, 1984

By Erwin L. Zodrow

"IntroductionThrough an extensive coal sampling project in the Sydney coalfield of Nova Scotia during 1981 - 1984 involving a majority of the mineable coals (Zodrow, 1985, Fig. 1), a sizeable inventory on trace, minor and major metals was established. In this paper, results of studying the inventory are summarized, concentrating mainly on the relationship that exists between metal variations and thickness of coal channel samples (i.e. trends) and on explaining the trends in geochemical and sedimentological terms. As an over-all conclusion the Everglades peat of Florida is proposed as a modern-day analogue to Upper Carboniferous peat swamp development that took place in the Sydney Basin.Data InventoryFor this study 17 channel samples were cut , 8 cm to 14 cm channel width and 8 cm to 10 cm depth, from 10 successive coals which in stratigraphically descending order are as follows: Point Aconi (3), overrider Lloyd Cove (2), Lloyd Cove (2), Stubbart (2), Harbour (4), Backpit (I), Phalen (,I), Shoemaker (1) and McAulay (I), where bracketed values signify the number of channel samples cut from a seam (Zodrow, 1985, Fig. I). Each channel sample was subdivided by 15 em incremental length yielding a total sample size of 137 for analysis. By appropriate modern techniques these samples were analyzed to determine concentration levels for 32 chemical elements and ash content, the average results of which are presented in Table 1.Tests were also made for Pd, Pt, Ga, Nb, Cd, Cs, Sm and W but their concentration levels in many instances hovered on the lower detection limits that were used and on this accounts are excluded from discussion. Ashing, when necessary for the determination of concentration levels, was done for 12 hours at a temperature not exceeding 450°C. Concentration levels for the elements are reported in reference to whole-coal or whole-coal equivalents and discussed on this basis. In the course of the analyses, lower detection limits received careful attention."

Jan 1, 1986

By Hani S. Mitri

Overhand cut-and-fill mining of narrow vein orebodies inevitably leads to the creation of horizontal pillars. As the thickness of the overlying crown pillar diminishes, stresses build up in the pillar. More often than not, this situation causes an increased level of seismicity and possible pillar burst. One well-known strategy to reduce the hazard of crown and sill pillar burst in cut-and-fill vein mining is that of destress blasting. The paper first reviews the methods used for the monitoring and assessment of potential pillar burst in narrow vein cut-and-fill mining. The influence of horizontal stress, mine depth and pillar thickness on stress build-up in the crown pillar is examined through a characteristic narrow vein numerical model. The paper then presents, with reference to three mine case studies, the benefits of destress blasting and the factors affecting its success as a ground control technique.

Oct 1, 2001

By J. E. Hawley

Introduction The Siscoe gold mine is the most easterly producer of gold from deposits lying in the belt of Keewatin and Timiskaniing rocks which extends east from Kirkland Lake, Ontario, and on through the Rouyn copper area. Unlike many of the deposits in this belt, those of Siscoe are contained almost entirely in a stock of much-altered granodiorite which intrudes Keewatin lavas. They are situated on an island of about one square mile in area, lying in lake De Montigny, Dubuisson township, 40 miles south of Amos, on the Transcontinental branch of the Canadian National railways, and 52 miles east, and slightly south, of Noranda. Geographically, the deposits are favour-ably situated with respect to transportation facilities, a through water-route being available from Amos, along the Harricana river and its lake expansions. The deposits consist of auriferous quartz-tourmaline veins of the fissure-filled type and are of particular interest because of their geological structure and genesis. Furthermore, deposits of a similar type occur both in the Keewatin and in granodiorite bodies to the east, in Dubuisson, Bourlamaque, Pascalis, and Louvicourt townships, and it is hoped that the following discussion may be of some aid in the exploration work now being carried on throughout this general area.

Jan 1, 1932

By A. J. Goodman

Introduction The position of Turner Valley in the foothills of Alberta, some thirty-five miles southwest of Calgary, is too well known to need further description. This attempt to interpret in detail the nature of the structure, and its relationship to neighbouring structures, together with general observations on the foothills belt, is based on work carried out in the office of the Supervisory Mining Engineer, at Calgary. The object in view was the correlation of the mass of evidence which had accumulated from the detailed examination of drill cuttings, and to discover, if possible, its structural significance. Unfortunately it is not possible to publish most of this detail owing to its confidential nature, and in consequence the reader is asked to accept certain statements, which under other circumstances would not be made without supporting evidence. The main argument for the general structural interpretation rests on evidence which has already been made public, and it is possible to proceed to logical conclusions on the main points. The evolution of ideas concerning the structure of Turner Valley is somewhat difficult to follow, as, compared with all that has been said on the subject, there is not a great deal on record.

Jan 1, 1930

By T. Banerjee, Y. Dumais, R. Lemire

"Agnico Eagle LaRonde produces over 300,000 ounces of gold annually, along with silver, zinc and copper by-products. The LaRonde plant consists of a conventional SAG and Ball mill circuit, followed by flotation. Load management is imperative for maintaining stability in grind size and ensuring consistency of the flotation feed. In flotation, the mass pull profiles of the cells and reagent dosage rates need to be managed to maximize recovery, while maintaining product quality. This is achieved by controlling the air, level and reagent addition set-points across the circuit. However, disturbances such as feed size distribution, ore hardness and mineralogy make it challenging to maintain efficient control using traditional control techniques. LaRonde therefore worked to develop a progressive control strategy, targeting stability and optimization. This started with a year-long instrumentation upgrade campaign, focusing on optimizing the performance and reliability of plant-wide instrumentation. The process was then optimized, leveraging AwaRE advanced controllers running in closed loop with PARC modules embedded within the PLC. The installation of 8 PFC cameras in flotation changed the flotation operation from a level and air control based strategy, to one that controls mass pull. This new control philosophy has allowed the plant to effectively manage mill load, improving grind size and providing increased throughput with better flotation performance.INTRODUCTION Background Since 2015, Agnico Eagle LaRonde has been conducting an optimization campaign to maximise the performance of plant assets leveraging instrumentation and control. The grinding and copper flotation circuits were identified as the areas having the greatest opportunities and value proposition for advanced control. A disciplined approach was followed to design and implement a progressive control solution to achieve operational excellence."

Jan 1, 2018

By R. D. Brown

The Federal Government's White Paper on Tax Reform received further major criticism in the reports of the Committees of the House of Commons and the Senate, which recently completed a lengthy review including public hearings of the government's proposals. These reports both criticized the emphasis placed by the White Paper on its concept of tax equity rather than on a system which would promote economic growth. However, the Finance Committee of the House of Commons was prepared to accept, with modifications, a number of the White Paper's key reform proposals. The Senate Finance Committee was more critical of the basic thrust of the tax reform program and recommended that a modification of the existing tax system would be more appropriate to Canada's needs. Both Committees re-commended a more favourable treatment of mining income than that originally proposed in the White Paper, and to some extent both Committees suggested proposals that were even more favourable to the industry than those set out in Finance Minister Benson's amended proposals made in August of this year. This article out-lines the principal recommendations and comments in the reports of both the House of Commons Committee and the Senate Finance Committee.

Jan 1, 1971

By M. F. Ameur, M. Habak, H. Aouici, M. Kenane

Present study interest by aluminium alloy (Al 7175-T5173) drilled without cooling fluid. The influence of the machining parameters (spindle speed and feed rate) on the holes quality was analyzed. Drilling tools are made of carbide (WC); high speed steel (HSS) and TiN coated carbide (WC-Ti).The Experiment design was reinforced by the application of statistical analysis of variance (ANOVA).The results show that the thrust force is influenced principally by the spindle speed and feed rate. Though, both feed rate and tool materials have statistical significance on the surface roughness. In addition, the objective of correlations between spindle speed and feed rate with the evolution of the machining parameters was established. These correlations were obtained by quadratic regression using the response surface methodology. Finally, useful to select optimum values of drilling parameters, that would minimize thrust force, torque, cutting temperature and surface roughness.

Jan 1, 2015

By Chuanhui Cao, Shimei Liu, Xiaojing Li, Yueyuan Zhou

"Force analysis on weakly-magnetic particles and non-magnetic particles in magnetic field are presented, using a kind of permanent magnetic drum magnetic separator, which is designed with strong specific magnetic force and open magnetic system. Its surface peak intensity reaches to 1.0T, and the distribution density of capture line is 1.25×103/dm2. Qualitative analysis on the particles including its magnetic property, particle size, motion speed, magnetic field intensity, etc. is also presented to calculate the separating parameters for the drum separator. Experiment was conducted for the separation of fine weakly magnetic minerals for example ilmenite. The practicability to separate the minerals using separator designed with open magnetic system has been proved, providing an economic way for efficient separation of micro-fine weakly magnetic minerals and upgrading of non-metallic minerals. INTRODUCTIONMagnetic separation is a mineral processing method based on the differences of magnetic properties between minerals in inhomogeneous magnetic field (Sun, 2007). Currently for separation of micro-disseminated weakly magnetic iron ore, electromagnetic high intensity magnetic separators with closed structure of magnet system are often used. And for the separation of strongly magnetic minerals such as magnetite, low intensity drum magnetic separators with open magnet system are often used. In order to lower the operation costs and improve energy efficiency, it is important to develop efficient high intensity permanent magnetic separator with open magnet system, to some extent replacing high intensity electromagnetic separator.Oberteuffer (1974) discussed the magnetic force and competing forces in magnetic separators which compete with the magnetic forces and act on all of the particles which travel through the separator are those of gravity, hydrodynamic drag, fraction, and inertia in magnetic separation."

Jan 1, 2016

By Constantin D. Pitis

?Demand-side measure" means a rate, measure, action or program undertaken to conserve energy or promote energy efficiency?? (BCUC, 1996) In actual economical environment, business sustainability requires high-efficiency technological processes. That is why the efficiency concept has to be present at all levels of industrial activities. Nowadays, some purchasing decisions are still driven predominately by the purchase price, in spite of the evidence that such price represents up to 5 % to 7 % of the total costs of ownership with full consequences of energy efficiency and the impact on total ownership costs. The paper presents essentials of converter types and basics of the Global Efficiency (GEff) Concept that has been promoted over the last few years in South African industries (Pitis et al., 2006/7). GEff concept is proven as a useful tool used on price-efficiency decisions. Theoretical and technical aspects of this concept were substantiated with case studies. First part presented in this paper will describe how GEff concept was used on price ? efficiency decisions when single input or direct converters and systems (considered as low value equipments) have been replaced. Besides the impact of energy savings and new innovative developments, the paper suggests general other benefits of: ? Technical and economical performance improvements and competitiveness of mining corporations to international standards; ? Defusing incipient energy crisis in the sector; ? Improving environmental conditions; ? Creating new job opportunities in mining sector. Proposed concept in this paper could be further developed as models of improving companies? corporate energy policies.

May 1, 2010