Search Documents

By Davood Moradkhani, Maryam Rasouli

"The present study reports solvent extraction and separation of zinc from concentrated nickel sulfate solution. In our previous study, Zn and Cd in cold filter cake (CFC, 45-55% Zn, 11-16% Cd, and 2.5-4% Ni) were extracted by alkaline leaching followed by electrowinning processes respectively. The strip solution from electrowinning process, was a pregnant liquor solution (PLS) containing 16.8 g/l Ni and 4.2 g/l Zn. In this work, PLS is subjected to the solvent extraction process for separation of traces of Zn from high grade nickel. The zinc free raffinate containing 16.6 g/l Ni sulfate solution will flow to nickel electrowinning plant for cathode production. Di-(2-ethylhexyl) phosphoric acid (D2EHPA) is the organic phase used in this study. The effects of various parameters such as organic phase concentration (10- 40 % v/v), pH (1.5-3), and temperature (25 and 45°) are investigated. Zinc over nickel separation factor increases by increasing pH from1.5 to 3. The results show that 98.7% of Zn was loaded at25°C O/A ratio of 1, pH 3, and 10% vol. D2EHPA. A 10 M NaOH is used for pH control. However, replacement of pH controlling agent with ammonia solution (25%. v/v) results in interesting observations. Ammonia addition, reduces the solubility of Ni2+ cations in solution. Nickel starts to precipitate from raffinate in a crystalline bluish-green form. The obtained crystals are characterized by XRF and identified to be nickel-bearing analog of boussingaultite, a rare sulfate mineral of nickel with chemical formula of Ni (NH4)2(SO4)2.6H2O. The crystallization rate of crystals is studied. It is a slow precipitation process with 75% in 4 days.INTRODUCTION Annually, many hydrometallurgical processes such as electrowinning, solvent extraction and leaching are applied to waste filter cakes in Zanjan, Iran. These additional processes on filter cakes are critical from both environmental and economic points of view. CFC (cold filter cake) is a toxic but valuable filter cake (45-55% Zn, 11-16% Cd, 2.5-4% Ni, and 0.2-1.5% Cu) produced in many zinc production plants. Our research group at Research and Engineering Company for Non-ferrous Metals (ReCo.), developed a series of hydrometallurgical methods for extraction of zinc, cadmium and nickel from CFC (Moradkhani, & Rasouli 2012). The recovery of zinc and cadmium with alkaline leaching and electrowinning was successfully studied. The strip sulfate solution from cadmium electrowinning unit, contains high concentration of nickel with some traces of zinc impurity. This pregnant liquor solution (PLS) was analyzed and reported to contain 16.8 g/l Ni and 4.2 g/l Zn. In this work, PLS is subjected to the solvent extraction process to separate Zn from nickel (Fig. 1). The organic phase stripping solution containing 4.2 g/l zinc and 200 ppm nickel can be circulated and used in the acidic leaching step. This generates nickel solution with high purity suitable for nickel cathode production."

Jan 1, 2017

By T. Crivits

"Freeze lining technologies are used industrially to protect the integrity of furnace walls in pyrometallurgical reactors. This is achieved by solidifying a protective layer of slag on the inner furnace wall. In the current study, laboratory experiments have been undertaken to produce freeze linings in ‘Cu2232 O’-‘FeO’-MgO-SiO slags under controlled conditions using an air-cooled probe technique. Whilst most thermal models of freeze linings have assumed the freeze lining-bath interface to be at the liquidus temperature of the bulk bath and to be planar in geometry, the current research has demonstrated that this is not the case. Experiments undertaken using this high-temperature slag system have shown the interface at steady state conditions to be at subliquidus temperatures. The solid phases present at the interface do not include the primary phase and the interface is non-planar. The study indicates the need for improved understanding of the fundamentals of freeze lining formation, and of the influence of system properties and process parameters"

Jan 1, 2015

By J. E. Nesset, F. Rosenblum, J. A. Finch, R. Payant

ABSTRACT Under certain conditions of moisture and oxygen, sulphides can spontaneously self-heat. We tested a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by the rest potential difference between sulphides and particle size. A series of binary sulphide mixtures was tested. Individual sulphides and mixtures with low rest potential difference did not self-heat, but mixtures of high rest potential difference did. When testing pyrite-sphalerite mixtures, self-heating increased inversely with particle size, with the fineness of the pyrite governing self-heating, indicating the rate-limiting step is the reduction reaction. The results support the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on hydrogen sulphide as an intermediate product is proposed. The understanding gained will be of interest to those involved in storage, shipping, and disposal of sulphides.

Jan 1, 2012

By G. H. Blackwell

Open pit mine management must ensure that sufficient trucks are available and are being used effectively for production, and that operating costs are under continued control and review for improvements. This paper describes methods for estimating truck fleet requirements which have been used effectively at large- and medium-sized open pit mining operations. Applied to commonly available data, multiple regression analyses can indicate when mine plans should be revised toward optimizing the number of trucks required. Prediction of major cost items for budgetary purposes is addressed, along with an example of how readily available production data can be used to reduce costs systematically.

Jan 1, 1999

By P. Kordi, L. Egorova, R. J. Bowell, D. Gurevich, V. Sedov, A. Mikhailov, D. A. Holwell

ABSTRACT Reconnaissance exploration in the Kuene region Namibia has included geological mapping, soil and stream sediment geochemistry, and ground geophysical methods. Copper mineralization occurs within a well-defined belt with north-northwest to south-southeast trend, parallel to the regional strike of the sedimentary rocks. The occurrences vary in size but are generally stratabound. The mineralization is centred on the transition from calcareous shale and interbedded limestone, through carbonate rocks, to quartzite. Geochemical anomalies have been identified correlating to induced polarization (IP) and magnetic anomalies. The anomalies identify one potential metallogenic zone more than 17 km in strike length.

Jan 1, 2012

By Victor Azbe

Azbe System of Controlled Calcination To obtain good and cheap lime there are certain fundamental requirements that need to be satisfied. These are : (1) Proper combustion of fuel and steady supply of heat to the kiln. (2) Proper heat distribution in the kiln. (3) Uniform drawing of lime through the several shaft sections. (4) Complete cooling of the lime and recovery of the heat. (5) Temperature control of the hot zone by economical means. (6) Ample draft to obtain high capacity. (7) Arrangements to facilitate operation. Figure 17 shows diagrammatically one of the smaller kilns, intended for large stone. Such a kiln can be supplied with gas from a centrally located automatic gas producer, or, as shown, from an integral producer located snugly against the kiln. These producers make very good gas and have a gasification capacity of either 10 or 15 tons of coal a day. The producers have water-sealed ash pits, a rather thick fuel bed that is conducive to the making of high-CO gas, and are under forced draft. No steam is used. Clinkering is prevented by admixing some spent gas from the kiln with the air. Coal feeding is from a coal bunker through spouts into the hoppers over the producer. This is done, at proper intervals, by manual operation of slides, but it is planned to install mechanical feeders. Central mechanical gas producers have the advantage of requiring little labour, but the blowing of soot is a problem, as also is the proper distribution of the gas among several kilns. In the case of integral gas producers, soot from the centre burner is blown back into the producer to be burned, and the supply of gas to the kiln is controlled by regulation of air to the producer. In large plants, the mechanical producer may be preferable, but in small ones, the integral producer is cheaper, better, and more reliable. The kiln shown in Figure 17 is suitable for both systems of gas supply. It will be noticed that there are no side gas burners. All gas enters the kiln through the centre burner in a manner that permits any desired amount of gas to be directed to any of the kiln sections by the aid of regulating slides.

Jan 1, 1946

By C. Hunt, J. Vivas, D. M. Allen

"In this paper we present the results of a combined remote sensing - numerical modelling study to improve our understanding of groundwater seepage in open pit and natural rock slopes, and to investigate the interaction between groundwater, in-situ stress conditions and brittle fracture. The location of seepage is a key element in the characterisation of rock slope stability in open pits and natural slopes; definition of the fracture network geometry and its inter-relationship with seepage, however, remains a challenge in engineering practice. Current techniques used to characterize groundwater seepage locations require direct access to the rock slope for a detailed and exhaustive investigation, and can be severely limited due to access and the limited coverage of the survey methods both with respect to the height and length of the sampled rock slope. Herein, we describe remote sensing methods, which allow the collection of structural and seepage information over a wide spatial area. Remote sensing techniques are shown to have the potential to provide additional insights into the orientation and general connectivity of fractures that may play a major role in the general stability of a rock slope. A preliminary methodology for the use of remote sensing in the characterization of seepage zones in a natural slope through the application of ground-based LiDAR and Infrared Thermography (IRT) is presented.One of the most challenging problems in rock slope engineering is the realistic simulation of fluid flow through fractured and deforming rock slopes. Deformation and the development of brittle fractures can cause significant local changes in the permeability and strength of the rock mass, potentially affecting rock slope performance. Understanding fluid flow through fractured and deforming rock slopes, especially in highly-stressed environments is of great importance for slope stability analysis. Changes in the interconnectivity of fractures during slope failure are an important, yet are relatively unstudied in rock slope engineering. We present the results of hydromechanical UDEC-Trigon rock slope models focussing on the potential role of brittle fracture in rock slope failure, its interaction with groundwater pressures, and the influence of the assumed in-situ stress ratio. Damage intensity parameters are used to characterize damage within different regions of a biplanar slope failure."

Jan 1, 2015

By J. Kang

Large-scale land reclamation has been undertaken in Singapore since the 1960s. In the early years, the fill materials excavated from the hills. In recent years, sea sand is the main source of the fill materials. The contractors used to import the sea sand from the neighbouring countries such as Indonesia. However, in early 2000, the sea sand import from Indonesia and Malaysia was banned. Cambodia, Myanmar, and Philippine therefore became the alternative sources for sea sand. Distance between the jobsite and these countries is over 1,200 km, and transporting sea sand from these areas became a critical issue that could affect the contractor?s performance. Figuring out the right combination of transportation means for a longdistance sand transportation would be challenging because of uncertain situations. We developed a stochastic simulation model, using ARENA, to figure out the right quantity of small-size barges, bulk carriers, and loading/unloading equipment, which could help project managers yield the most production for sand transportation. This paper presents how we developed the simulation model, how it was applied to figure out the optimum combination among various size barges, different bulk carriers, and various types of loading/unloading equipment, for the sand transportation project in Singapore.

Aug 1, 2013

By I. Nakatsugawa

Chemical conversion coating is a process to create thin oxide/hydroxide film containing several inorganic/organic compounds by way of chemical deposition reaction. In case of the application to Mg mobile electronic housings, the film should possess a good electric conductivity while keeping adequate corrosion resistance and working as a paint base. The use of toxic/hazardous chemicals is strictly prohibited from the environmental aspects. This paper describes the recent trend of conversion coating used for Mg electronic housings and analyzes critically from the point of surface technology. The importance of cleaning process and understanding of surface microstructure are particularly emphasized with several experimental results.

Jan 1, 2006

By A. Rahimi

Refractory castables based on alumina-silicate aggregates are commonly used in casting wheel components and launders. In this research the recycling process of waste magnesia chrome bricks for production of refractory castable lining for launders and casting wheel ladles at Iranian Sarcheshmeh copper complex (I.S.C.C.) is discussed. The smelting plant of ISCC consumes 4,000 tons refractory materials and produces 2,000 tons waste refractories annually. In order to reduce the environmental pollutions and gain the economical advantages, the recycling of waste refractories proved to be a solution [1]. In ISCC, 800 tons alumina or alumina-silicate refractory castables are used for linings of anode furnace ladles and launders annually [2]. In the present work, the spent bricks from reverberatory, converter and anode furnaces were analyzed in term of microstructural changes from hot zone to the cold end to evaluate the changes in texture and chemical composition. Different formulations based on recycled magnesia chrome aggregates and various particle size distribution and cement content were tested. Economic recycled magnesia chrome refractory mixture was prepared after crushing and sizing the non-deteriorated regions of wasted bricks. After evaluation of physical and mechanical properties of samples, one ton of refractory castable was prepared and successfully installed in the casting wheel ladles.

Jan 1, 2007

By Lloyd Buckingham

Barrick Gold Corporation (Barrick) has undertaken innovative methods of evaluating and improving the performance of grinding mills in several of its operations around the world. The results have been positive with some of the mines showing more than 20% net energy improvement leading to more than 43,000 tonnes per year reduction in CO2 emissions in four of the operations reviewed.

Jan 1, 2012

By J. D. Aitken

"DEFINITION OF THE REGIONTHE REGION considered in this paper is bounded on the south by the 60th parallel, on the north by the Beau-fort Sea and Amundsen Gulf, on the east by Archean rocks or by highly deformed Proterozoic rocks of the Canadian Shield (certain weakly deformed Proterozoic strata being regarded as belonging to the Great Plains), and on the west mainly by the Mackenzie and Richardson Mountains.Only the unmetamorphosed strata of the region are considered; that is, the geology of the crystalline basement is ignored.SIGNIFICANCE OF THE REGIONThe region is significant from three points of view -namely, the economic, the scientific and the social. It constitutes 46 per cent of the area of the Western Canada Sedimentary Basin."

Jan 1, 1970

By W. Beres

Many non-commercial operators are currently faced with the need to operate fleets of legacy gas turbine engines. How long such engines can be kept in service safely, without replacing a significant portion of their aging structural components, has become a growing concern to engine life-cycle managers, due to uncertainties in the remaining lives of critical components of these engines. This paper describes the application of the damage tolerance methodology to predict safe inspection intervals (SII) for critical components of gas turbine engines, using components of a turboprop engine for a transport aircraft as examples. High temperature components of this engine are made of advanced aerospace alloys. The methods of predicting three-dimensional fatigue crack growth at the critical location of turbine discs and spacers using both commercial and in-house developed algorithms are presented. Sensitivity analyses are performed to determine the effect of variations in material parameters on the predicted safe inspection intervals. In addition, spin rig tests performed for both turbine discs and spacers are described. Finally, crack growth rates predicted by numerical analyses are compared to those obtained from spin rig testing and the damage tolerance of the turbine components is assessed.

Jan 1, 2015

By Y. Thibault, G. Deschênes

An open-pit mine, located in Mexico, processes an ore a rate of 4000 tpd, using conventional cyanidation and AYR. A laboratory study was conducted to increase silver extraction and to reduce the concentration of cyanide in leaching. The sample contained 0.41 g/t Au, 125 g/t Ag, 99% gangue minerals, 0.7% pyrite, 0.07% sphalerite, 0.03% chalcocite. Silver was present as acanthite, stromeyerite, silver mercury/halogen, silver with copper in solid solution and jalpaite. The plant conditions (2400 ppm NaCN) produced 90.2% gold extraction (residue at 0.04 g/t Au) and 92.7% silver extraction (leach residue at 9.1 g/t Ag). The CELP (CANMET Enhanced Leaching Process) produced 97.0% silver extraction (residue at 3.8 g/t) and 90.2% gold extraction using 500 ppm NaCN. The incremental gross revenue was estimated at $US7.6 million and the reduction of cyanide costs was $2.9 million per year (79%).

Jan 1, 2011

By P. Marcotte, G. LeBlanc, S. Ouellette, J. Boutin

"To characterize noise and vibration sources of different types of mining equipment used in underground mining, the authors performed a study in eight Quebec mines on 28 pieces of equipment. This paper presents the procedure followed to select the equipment to be evaluated, and the low-cost acquisition system developed to perform multichannel time-domain data acquisition in harsh environments. It also presents the results obtained for the noise level produced by the equipment and for handarm and whole-body vibration exposures.RÉSUMÉ Dans le but de caractériser les sources de bruits et de vibrations de divers équipements miniers utilisés sous terre, les auteurs ont étudié 28 équipements dans huit mines du Québec. L’article présente la procédure suivie pour choisir les équipements à évaluer ainsi qu’un système multicanal à faible coût développé pour acquérir des données dans des environnements difficiles. Il présente aussi les résultats obtenus pour les niveaux de bruit produit par les équipements et pour les expositions main-bras et du corps entier aux vibrations."

Jan 1, 2015

By M. Sengupta, A. A. de Gast

"With rapid deterioration in the urban environment caused by air pollution, the possibility of chemical reaction between dimension stone and the industrial waste gases present in the ambient atmosphere remains. The chemical reaction can cause expensive damage to building stone; it is essential that a stone evaluation for use in construction should assess the possibility of this type of decay. This paper endeavours to develop testing procedures for evaluating stone decay in polluted environments. Such tests can accompany other standard tests used in dimension- stone evaluation."

Jan 1, 1972

By R. L. Stanton

"The present contribution examines, in some detail, what appear to be the three outstanding features of the field occurrence of the conformable ""pyritic"" deposits. These are their association with fragmental volcanic rocks (and derivatives), their occurrence in sediments of near-shore formation, and their highly variable structural associations.In a recent paper it has been suggested that two such ""pyritic"" de-posits in New Brunswick may have originated as marine concentrations of volcanic base metal and sulphur compounds, and that many of their present features are the result of diagenesis, folding, and regional metamorphism. This is now put for-ward as a general explanation for the particular class of deposit considered.Such deposits should, on this hypo-thesis, be regarded quite simply as an integral part of the particular geological environment in which they occur -as a normal, though minor, sedimentarry type developed, char-acteristically, in near-shore and shelf facies of intravolcanic units formed along the margins of eugeosynclines. They should not be considered -as, for example, is required by the re-placement theory -as later features simply superimposed on a geological situation to which they are genetically unrelated. Where they are associated with folds and other structures, this may be attributed, from one in-stance to another, to mechanical migration during folding, weaknesses induced by pre-existing sulphides, and, occasionally, to fortuitousness.In the light of this postulated origin, it is suggested that the first stages in regional prospecting for deposits of this particular class should be broadly palaeogeographical. Later phases of the search should then be directed to the delineation of sedimentary facies and, finally, to the investigation of geological structure."

Jan 1, 1960

By G. J. Birnie

Introduction The preparation of the following paper has been undertaken in the belief that a description of the development methods and equipment used at Lake Shore, at the present time, will prove of general ? interest. Working depths of nearly a mile and a half in shaft sinking and of more than one mile for stoping operations have imposed problems not encountered at shallower horizons. Among the problems contributing to the difficulty of mining at extreme depths might be mentioned: Rock pressures Ventilation Hoisting Shorter work period at the face Geological considerations In the main, the effects of these factors add to the difficulty of mining at depth, but it is not entirely true to say that each must necessarily become more pronounced as mining operations proceed to greater depths. Corrective measures may, in some cases, retard the effect and in others may even relieve some of the difficulty. It is proposed here to discuss these features in the light of the experience at Lake Shore, and to present, in some detail, the current practice in shaft sinking and in driving ore and waste passes, raises, drifts and cross-cuts.

Jan 1, 1950

By Y. Héroux, A. Chagnon, M. M. Savard

"Résumé- Le gîte de Pb-Zn de Gays River s'accompagne d'anomalies des propriétés de la matière organique (MO) et des assemblages de minéraux d'argile (AMA). L'association entre la minéralisation, la distribution de la réflectance de la MO et des AMA suggère que ces traceurs peuvent servir à l'exploration des sulfures de métaux de base dans cette région.A l'emplacement du gîte, la réflectance varie considérablement (0,80% à 1,88%), pouvant même afficher une baisse avec l'enfouissement, ce qui est interprété comme une altération chimique de la MO. Les valeurs les plus élevées s'accompagnent localement de quelques textures en mosaïque et délimitent une anomalie thermique au centre sud de la région. Parmi les minéraux des argiles identifiés, l'illite et la chlorite sont terrigènes alors que la smectite, la kaolinite et la corrensite sont authigènes et, à l'instar de l'altération de la MO, résultent des nouveaux équilibres chimiques créés suite à la précipitation des sulfures.Abstract- The Gays River Pb-Zn ore deposit is associated with anomalies defined from the characters of the organic matter (OM) and from the clay minerals assemblages. The relationships be­ tween these anomalies and the mineralization at the mine suggest that these parameters can be used as new guides for the exploration for base-metal sulfides in this area.The vitrinite reflectance (RJ shows a wide range of values (0.8% to 1.88%) and exhibits an anomalous suppressive effect with depth of burial at the mine site, suggesting a chemical alteration of the OM. The highest R, values are associated with mosaic textures and outline a thermal anomaly at the south-center of the studied area. Among the identified clay minerals, illite and chlorite are terrigenous, whereas smectite, kaolinite and corrensite are authigenous and, like the alteration of the OM, are due to the new chemical equilibria resulting from the precipitation of the sulfides."

Jan 1, 1994

By B. B. Adhikari, S. Alam, Ohto Kawakita, Abe Pangeni

Effective recovery of gold was investigated by using adsorption gels prepared from pure cellulose, cotton and paper by treating with concentrated sulfuric acid. Only gold was adsorbed with extraordinary high loading capacity from varying concentrations of hydrochloric acid separated from other precious metals and base metals. The formation of fine powders of metallic gold was visually observed, which is attributable to the selective reduction of gold (III) ion to metallic gold clue to its high oxidation-reduction potential. Recovery of gold from the leach liquor of hydrochloric acid of circuit boards from spent mobile phones was attempted using pure cellulose gel.

Jan 1, 2011