Search Documents

By Paley N, Cameron A, Townson P

Although blasthole deviation is a problem which can seriously affect blasting operations, there is little practical emphasis on controlling this deviation and no practical emphasis on understanding its practical behaviour. The most common way of dealing with it involves tight control over drill set up and surveying hole paths. The surveying might involve simple collar location and inclination measurement to estimate the hole's actual path. At best, some operations routinely survey hole paths after all holes in a stope have been drilled. In addition, although there is an expectation that holes will deviate, there is no planning for this behaviour in order to reduce its impact on the blast. Design decisions are invariably made with the assumption that holes are straight. If and when surveys reveal problems it is possible only to adjust charging and initiation to 'work around them'. In extreme cases the drill might be recalled to fill in gaps. The lack of planning and the lack of understanding are doubtlessly linked.A model is presented that will predict the expected path of a drill hole. By knowing how a selected few holes deviated it is possible to make a good estimate of the deviation of other holes in the same rock mass. After minimal calibration the model can be used to increase the amount of information for a given amount of surveying or the amount of surveying can be reduced while maintaining the same level of knowledge of blasthole deviation. Equally important is the ability to plan for the deviation in future drilling through altering the initial collar angles or drilling from different locations. It is the authors' hope that planning for hole deviation becomes as much a part of the design process as planning for detonator delay scatter and explosive performance variation.

Jan 1, 1992

By Hood M

Rock cutting excavation technologies and particularly continuous excavation technologies, can offer benefits in the areas of reduced costs, higher revenue and increased safety in a variety of mining situations. Non-explosive rock excavation technologies for example, can deliver significant benefits in the areas of dilution and improved ground support (no overbreak). This paper is an attempt to focus on the development and future of alternative rock breaking technologies and to provide some insights as to why and how we should proceed in this direction. The market size for underground hard rock excavation technologies is examined. A short review of the evolution of various rock excavation technologies in terms of cost and production rate is given and a summary of the state-of-the-art technology is presented. Mechanical excavation technologies (TBM) have very high production rates compared to D&B and the gap is widening, however, they have not been successfully applied to mining applications. Operating costs for mechanical and D&B systems have been dropping over time, however, D&B costs are the lowest. Given the current state of knowledge it appears that with regard to hard rock underground metalliferous mining that R&D efforts should be focussed in the following areas - disc cutter tool development (materials and design; operation; presentation to the rock surface), hybrid cutting systems (consisting of water jets and disc cutters) and development of pressurised hole breakage technologies. It is also possible that two techniques known as the pulsed laser and pulsed water jets may have some potential. The generally agreed specifications for a widely applicable underground hard rock excavating machine are - disc cutter based, a minimum production rate of 100 t/h, be flexible, manoeuvrable and deployable, weight of less than 100 tonnes and be economically competitive with D&B in rocks over 150 MPa UCS. Such a machine would seriously challenge the position of conventional D&B in a wide range applications and provide some of the benefits of mechanisation and automation that the mining industry is pushing so hard for. However, technology developments in the D&B area are not static and hence the target is moving and is increasingly difficult to overtake.

Jan 1, 1995

By Hashimoto H, Arai Y, Sikong L

For utilization of solid carbonaceous materials produced in processes of cracking heavy oil, such as petroleum pitch, as powder fuel, it is necessary to develop a process for fine grinding of these materials. It is known that grinding' additives are effective for fine grinding of cohesive and heat-sensitive materials such as petroleum pitch, therefore in this study, effective methods for fine grinding of petroleum pitch with some grinding additives were investigated. Experiments were carried out by using comminution kinetics based on mass balance. From the results of the investigation by using a batch ball mill, it was found that sodium stearate, calcium stearate and carbon black were effective additives for the improvement of grinding efficiency. Optimum concentration of the grinding additives was also found to give a required particle size of products. Concerning to the action mechanism of these additives, it is considered that the additives which adhired to, or were absorbed on the surface of petroleum pitch particles not only prevented cohesion of the particles but improved dispersion of the particles as well. From the results of the investigation by using a laboratory screen mill which is a representative built-in classifiered impact crusher, carbon black was found to be an effective additive for the improvement of grinding efficiency and mill performance. It is also considered that the improvement of classification efficiency by carbon black affected the mill performance.

Jan 1, 1987

Best practice in environmental performance is a principle now increasingly and rapidly transferred around the globe. This matches both the greater rigour of environmental standards and the growing uniformity and `internationalisation' of standards for environmental management. There is no difference in the application of Normandy's environmental policy anywhere in the world.Normandy Mining is developing an Environmental Management System (EMS) which will satisfy:ò the need for technical excellence and best practice;ò the need to demonstrate `due diligence' in any jurisdiction;ò the need for financial statements and for insurance to reflect real world requirements for management of risk and liability.

Jan 1, 1997

By Little T. N, Bettess D

For many mining operations the challenge of equalling World Best Practices has become the key motivator for increasing mine productivities and for lowering total costs. In most instances this will only be achieved if mines optimise their total system rather than minimising specific costs within unit operations. In the past, drilling and blasting have been viewed as a cost to be minimised rather than operations which should have their impacts fully leveraged. Once a hardrock orebody is defined the activity which has the most substantial impact in determining the efficiency of a mining operation is the blasting. The output from a blast affects every downstream operation; only by understanding the extent and interactions can the mine be optimised. Substantial improvements to hardrock mining, quarrying and excavation operations are achievable. Instead of seeking the regular one to three per cent improvements based on reduction of consumables, mine operators would be well advised to go for much bigger targets of ten to 30 per cent by fully leveraging the drill and blast operations.

Jan 1, 1995

By P R. G Milne

A risk-based approach to optimising pit wall slope angles was trialled in the design of a 60m deep open pit in extremely weathered and distinctly weathered materials in the Kalgoorlie area. The pit used for this approach was Stage 1 of a three-stage open pit project. The Stage 3 pit will require long term stability, as it will contain the portal for a long life underground project. Information from failures induced by steeper wall angles used in the Stage 1 pit would be valuable in predicting and preventing long-term stability issues in Stage 3. In this approach, the pit wall slopes are based not on the normal factors of safety, but on the assessment of the probability of failure and the direct and indirect costs of dealing with the failure when it occurs. In this example, the benefits and risks of adopting steeper wall angles were compared in a series of graphs. These charted the increasing probability of failure and simultaneous decreasing factors of safety with increasing pit wall slope, and the range in the possible volumes of circular failures for increasing wall angles. These were brought together in a graph showing the potential excavation savings (in BCM) and the probable cost of a failure (probability of failure times the probable volume of the failure). The resulting pit design was based on the project Mining EngineerÆs semi-quantitative assessment of where and when a higher risk of failure was acceptable and where it was not acceptable as it may have unduly affected the integrity of haul roads or production. The design incorporated wider than normal berm widths to accommodate anticipated failures and to enable modification of the wall configuration if required. Several re-designs were required during the life of the project in response to aggressively induced failures. It is considered that this risk-based approach provides a practical route to optimal pit design and operation but it requires an experienced, dedicated and efficient mining team for it to be implemented with benefit.

Jan 1, 2003

Exceptionally weak ground, usually associated with faulting, unanticipated groundwater pressures or flows and exceptionally high stress concentrations are some of the hazards which confront the underground excavation engineer. One or more of these hazards can seriously delay or even halt a tunnel or mining project, and methods for predicting these hazards are urgently required, particularly for projects involving high speed drill and blast or tunnelling machine excavations.This paper explores the current availability and the potential for the development of tools and techniques for the prediction of these hazards. It is concluded that systematic and automated geological data collection and interpretation represent the most promising avenue for development. It is suggested that there is room for the use of expert systems in which the computer is used to assemble and organize practical underground excavation experience into an interactive decision making system.

Jan 1, 1985

o Resource production is essential for society. o Demand for resources will increase as population grows.o Resource industries are the main consumer of trained geologists.o The lead time from(1) training to productivity(2) research to resource production is measured in years.o An adequate supply of well trained geologists and successful geological research is an important agent in ensuring cost effective, adequate supply of mineral resources for society. Therefore the main beneficiary of geological education is society itself.o Society is paradoxically apathetic or antagonistic to the resource industry because (1) it represents change(2) lobby groups working for other causes have successfully moulded a bogey man image for the resource industry in the public eye.Professional training and research for resource industries consequently lack popular support. Funding is at an absurdly low level in comparison with the economic importance of resource supply.

Jan 1, 1990

A resume covering currently accepted views on blasting vibration measurement, human response, and criteria for damage is presented as background information for readers who are not conversant with blasting vibrations. This is followed by sections on vibration level estimation and blasting techniques to control vibration. Emphasis is placed on making use of the scatter in the delay intervals of half-second delay detonators, the use of smaller explosive charges for early delay numbers, and the non- use of zero-delay (instantaneous) detonators in cer`a. n cases.

Jan 1, 1976

This paper comprises a discussion of standards for comparing conditions in mines, of methods for measuring the flow of air, of a comparison of fan performances, and the application of these matters to mines in Western Australia.UNDERGROUND CONDITIONSIn approaching the question of mine ventilation one naturally searches for some standard by which to measure the conditions in a mine.There are several clauses in the Mines Regulation Act defining the conditions which are permitted. The quantity of CO2 is limited to 0·25 by volume, but the estimation of CO2 involves a chemical determination and is not suited for general use in a mine.The maximum temperature is fixed at 87 0 F. (dry bulb), and at 80° (wet bulb). The reading of temperature is easily done in the working places, and this is a very valuable and practical test of the conditions in a mine.The wet bulb temperature is probably the most important factor in determining working conditions. It is obvious that human life cannot be sustained for any appreciable period if the wet bulb temperature is above blood heat (about 97°F.). In places where the wet bulb temperature is 90°F. there is danger of heat stroke.In places where the air in a mine is still, the wet bulb temperature rises to a value close to the rock temperature.Adequate ventilation cools the workings by transference of heat from the rock to the air stream, and the temperature...

Jan 1, 1939

The basic principles of mineral valuation were recognised and propounded at the beginning of this century and have remained virtually unchanged since then. Valuation is seen as a two part process commencing with a technical examination of the mineral property followed by a manipulation of the results of the technical examination in order to determine the monetary value of the project. A thorough and competent technical examination was seen then and remains now as the essential but not sufficient foundation for reliable valuation. All authors stressed the need to maintain the integrity of the data base and to ensure adequate coverage of all relevant aspects. The monetary valuation process through most of the first half of this century was mainly based on the Hoskold two rate method, derived from the formulae for valuing annuities but modified to provide explicitly for recovery of capital. Though the basic principles of valuation have not changed significantly, the means of implementing the components of the technical examination, the styles of deposits being evaluated and the mechanisms of monetary valuation have changed dramatically. Despite all the technological improvements, however, mineral

Jan 1, 1995

By A H. Hofstra, G P. Landis, P Emsbo, A G. Hunt

Models of the evolution of the hydrothermal systems that form porphyry Cu (Mo-Au) deposits are compromised because aqueous magma-derived fluids in the ore zones of most deposits have changed from their original magmatic compositions as a result of cooling, depressurising, mineral precipitation, brine-vapour unmixing and fluid-rock reactions. However, in deep quartz-rich, sulfide-poor veins from numerous porphyry type deposits, we have identified parental fluids trapped in inclusions at near magmatic temperatures and pressures above the brine-vapour unmixing solvus. We have analysed these inclusions for bulk salinity, density, solute chemistry, helium isotopic ratios and elemental composition. These parental inclusions contain 35 - 70 volume per cent bubble, are low to moderate salinity, contain up to ten mol per cent CO2, and commonly contain a chalcopyrite daughter crystal. Our results indicate that these Cu-rich fluids transport Cu from a plutonic complex below upward into a hydrothermal system, where decompression, cooling, unmixing and water-rock reaction drive ore-mineral precipitation. Na/Cl ratios greater than one indicate that in addition to chlorine, sulfur and/or carbonate must play a key role in Cu transportation. Helium isotope ratios indicate that between ~15 and 100 per cent of helium in these fluids is mantle-derived. We suggest that in addition to He, volatiles from mafic magmas in the mantle are also likely to supply CO2, Cu and S to the fluids that form porphyry copper deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The key elements required to maintain final wall integrity and hence slope reliability are discussed. Failure modes and mechanisms in highly structured rock slopes are then reviewed. The impact of blast disturbance on rock masses in general is discussed and the relationships between the slope failure mode and blast disturbance is then explored. The question of how designers can incorporate such impacts into the slope design process is then addressed. This necessarily involves rock mass strength consideration and two case studies are used to demonstrate a recent dilemma in this regard. Some progress regarding this dilemma has also been reported for the second case study. The major conclusions are that: Slope reliability can be severely compromised if the slopes are damaged by blasting and this impact is not often incorporated into the slope design process. The location and extent of the blast damage will impact some slope failure geometries and failure mechanisms more than others. The concept of failure mechanism specific vulnerability needs to be further developed. The evidence indicates that this aspect is even more extreme for weak ground conditions. The quantification of the reduction in rock mass strength due to blast damage is not well understood and limitations exist with some recent guidelines. The use of the Hoek-Brown criterion for slopes in blocky rock masses requires considerable judgement. Further applied developments in this regard would be very beneficial to the industry. Some promising methods to incorporate blast damage estimates into the slope design process are emerging. It is good business to minimise final wall blast damage otherwise a whole range of issues relating to reduced slope reliability emerge.

Jan 1, 1999

By M Fimeri, R Williamson

Sample sizing in the iron ore industry requires significant manual effort to collect, transport, and sieve the samples as well as record, process and report the data. Efforts have been made to automate this process, which essentially emulate the manual process, except that a person is replaced by a robot. Even in these cells, the sieving and sizing operation consumes a significant proportion of robot time. The proposed doubling of production from AustraliaÆs iron ore mines over the next five years will place increasing pressure on sample sizing and interest is increasing in alternative automated methods. One such method is the adaptation of computer vision technology which has been successfully introduced into the mining industry in a range of applications including feed size distribution to SAG mills and oversize detection from screening stations. The limitation of this technology is that only the top surface is visible and this is used as an indicator of total size distribution. Obviously in a sample plant, where 100 per cent of the sample must be measured for acceptable quality assurance, this approach is unacceptable. In order to capture 100 per cent of the sample using computer vision technology a monolayer must be formed either by spreading the sample across a moving surface, such as a conveyor or vibrating platform, and passing this under a camera. This will become a æsurgingÆ load which presents specific problems for some types of computer vision systems, namely those relying on a 2D approach. In this paper a 3D computer vision technology will be described which overcomes the problems associated with measuring particle size in a monolayer and experimental results will be presented which demonstrate its effectiveness for lump and fine iron ore sample size measurement.

Jan 1, 2008

Mr. Bradford said: - On assuming this chair, which has been oc- cupied by so many gentlemen of conspicuous ability, my first words must be an expression of the gratitude I feel for the honour you have done me in electing me to be your President for this year. When considering the subject matter of this address to you to- night, quite frankly may it be stated that for a long time I was on the horns of a very great dilemma, for while I could discourse on the modern political trend in relation to our industries at great length, it appeared to me that this was not the place for such a discussion.

Jan 1, 1987

The necessity for agreed project outcomes, which are in accordance with client needs, and the subsequent requirement for a unique approach to managing project implementation is discussed. Reasons for appointing a separate project team to manage a project are established. The selection of a project manager, based on the services they can provide and on their characteristics, skills and management style, is discussed. The consequences of selecting the wrong project manager are explored. A broad overview of the requirements for the project team is provided. Criteria for the selection of team members, and the role played by the project manager in this selection, are discussed. The levers that drive `on-time and on-budget' projects are discussed in terms of the project's vision, goals, controls, and incentives.

Jan 1, 1997

By Hohnen CA, Limerick JM, Hall DRT

An uniquely-designed flash furnace for smelting of nickel concentrate and for the recovering of metal values from the slag generated has been in successful use for nearly six years. Within the last eighteen months the ability of the furnace to treat slag arising from converting operations without significant reduction in capacity has also been successfully demonstrated. Previously, converter slag had been treated separately in an electric furnace. The salient features of smelter developments are outlined and slag chemistry is discussed. The low cost method for the introduction of coal to partially replace light fuel oil is reviewed and total energy requirements evaluated.

Jan 1, 1984

By Shining Z

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The rheological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

The metallurgical testwork program is generally the most important critical path item for the completion of a bankable feasibility study and hence can become the critical parameter for financing of potential mining projects. This paper presents generic detailed testwork programs suitable for bankable feasibility studies for a gold leaching and polymetallic flotation study. The design of the metallurgical testwork program for each of the two differing processes is discussed and the critical factors that effect the selection of the testwork programs are highlighted. The importance of the metallurgical testwork results in predicting the metal recoveries and cash flow prediction for the project is presented. The detail of the testwork programs costing is broken into activity based methods based on the laboratory and management hours/costs, such that generic rule of thumb costing guidelines can be generated. The scheduling, costing and importance of the metallurgical testwork program to process feasibility studies are discussed in this paper.

Jan 1, 2000

By Lightfoot BW, Bultitude-Paull J

The Sirosmelt top submerged lancing system has many applications in the smelting of base metal and complex materials. It has particular advantages for smaller scale smelting and the treatment of recycle materials in smelters where its low capital and operating costs and its operational flexibility are of immediate benefit. The system can be fueled by oil, gas or coal, as well as by mixtures of fuels. For many applications, the use of coal as a fuel has operating cost advantages over oil and gas, but conventional pulverised coal feeding systems entail very large capital expenditure and this militates against the use of coal. The methods available for improving on conventional technology for coal firing of Sirosmelt systems are discussed and operating experience with alternative systems are outlined. The use of coal as a reductant in the Sirosmelt system is also discussed.

Jan 1, 1987