Search Documents

By Davey P. T, Tsambourakis G

Mineralogical analysis of supergene sulphide ore recovered from areas close to the underground workings at the abandoned Mutooroo (South Australia) mine shows that the original sulphide minerals have undergone substantial alteration. The cause of this alteration is believed to be contact with the highly saline, acidic mine water. The copper is now present as a sulphide that can best be described as a copper- and iron-delicient chalcopyrite, CuxFeyS2, where in most cases x < y. The values of x and y vary from point-to-point within each grain.Leach tests under a variety of conditions show that dissolution of the copper from the supergene sulphide ore can be readily achieved, particularly when compared with the behaviour of Mt Isa chalcopyrite concentrate. For the supergene sulphide ore, an increase in the acidity and the iron(lll) concentration of the leachant re ults in an increase in the rate of copper dissolution.The results are briefly discussed in terms of the experimental in-situ leaching operation at Mutooroo, South Australia.

Jan 1, 1986

An improved method of sample recovery for use with rotary percussion drilling has been developed. Cuttings can be recovered continuously from either dry or wet drilling, and the recovery under dry conditions is seldom below 99% of the cuttings brought to the surface by the rig. The system is designed for use with top drive drilling rigs using flush-jointed drill rods. The key feature of the system is a self-aligning mechanical seal around the drill rods. The sealing unit is removably fixed to a collar section of cas ing. the cuttings are recovered in a plastic bag attached to the bottom outlet of a cyclone. A valve at the bottom of the cyclone permits the cuttings representing various depths to I,e recovered separately for examination eind 0(iclysis. [u the Iron Monarch quarry, two percussion holes were drilled to depths if 30 metres and 28 metres using the unproved sample recovery system, and diamond drill holes bored 1 metre from each percussion hole. Samples from each hole were sectionalized over metre intervals and analysed for iron, silica, alumina and loss on

Jan 1, 1976

By P J. Scales, D Boger

Technological advancements in mineral processing have increased the feasibility of refining low-grade ores. Because of this progression and continual depletion of high-grade ore deposits, much larger volumes of waste material are produced. At the same time, increasing environmental legislation and cost competitiveness dictate that these wastes be disposed of in a manner that is both environmentally acceptable and economically viable. To achieve these criteria, many mineral processing industries are dewatering waste streams in order to reduce the volume of tailings and increase water and reagent recovery. The subsequent dry disposal of these highly concentrated mineral tailings requires a thorough understanding of the effects of dewatering on the flow characteristics. Dry disposal represents a paradigm shift in engineering. The tailings are engineered to suit the disposal requirements, as opposed to engineering a facility to accommodate the tailings. It is therefore important to understand how the material properties and operational parameters can be modified to produce the desired tailings flow and deposition characteristics. As concentrated suspensions usually exhibit non-Newtonian behaviour, determination of the disposal plant operating conditions requires a thorough understanding of the rheological characteristics of the material. The implementation and optimisation of dry disposal methods involves three concurrent and interdependent rheological studies to determine:the concentration required to achieve the optimum spreading and drying characteristics of the tailings once deposited; the optimum conditions for pipeline transport; and the feasibility of dewatering the slurry to the required concentration. The paper presents an overview of the issues pertinent to management of the flow properties and processing of dewatered waste streams.

Jan 1, 2002

Mining companies in order to compete and succeed in being viable business propositions must look to the future and select mining methods which guarantee improved efficiency and productivity as well as lower costs.A mining company in adopting a method of mining must now select the equipment most compatible. To some mines compatible equipment may mean the use of drilling jumbos to replace hand held rock drills or the use of load haul dump units to replace scrapers. To other more mechanized mines compatible equipment may mean the use of raise borers and road heading machines. The right decision will be where equipment compliments method in such a way that the working environment is improved, productivity is maximized, cost if reduced and all profit opportunities are optimized. An example of such is where the use of improved mining techniques in underground operations may see cut off grades reduced. By selectively mining these lower grade orebodies, smaller operation's ore reserves improve and the capacity for continued growth is enhanced.

Jan 1, 1990

Iron ore in the Pilbara Region of Western Australia varies in composition giving iron ore a range of densities. An accurate density figure of the material leads to accurate calculations of production throughput. Density studies of two separate iron ore mines were conducted in the Pilbara. Procedures and results are reported here.The Pilbara Region of Western Australia has a number of iron ore operations. Two mines have conducted density studies of their materials. The purpose for the studies was to determine an accurate in situ bulk density that could be applied to volume and tonnage calculations of the operation. It was identified that density was one culprit causing calculation variations. Density is an important figure used to estimate ore reserves, equipment requirements, production rates and indirectly costs and sales revenue. One study was conducted at Rio TintoÆs Robe River Mine based near the town of Pannawonica. Its Mesa J orebody is currently being mined and is a low-grade deposit of goethite and hematite (Burnham, 2003). A separate study was conducted at BHP BillitonÆs Yarrie Mine situated north of Newman and east of Pardoo. Its orebody consists of high grade formed by a supergene enrichment of cherty material and a burial metamorphism to produce hematite (Richardson, 2002). The method used to determine density was by large-scale samples using the pre-mining in situ volume of the material and the weight in tonnes after mining.

Jan 1, 2003

The Government Mining Engineer of South Africa has decided to legislate that Self Contained Self Rescuers (S.C.S.R.) become a mandatory piece of equipment for all those persons proceeding underground. It is envisaged that: * employees in underground coal mines will be fully equipped with S.C.S.R.s during 1988; * those persons employed in gold mines during 1988/89; and * personnel in all other mines by the end of 1990. It is the intention of this paper to discuss the introduction of these auxiliary life support systems, and to give an update on current market developments.

Jan 1, 1988

By Lauha E. A

The Goldstrike Mine is in Eureka County, Nevada, U.S.A., approximately 23 miles northwest of the town of Carlin. The mine is at the north end of the Tuscarora Spur of the Tuscarora Mountains at elevations of 5,300 feet to 5,950 feet. It is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend, a northwest alignment of sediment hosted, disseminated gold deposits. The Carlin Trend includes over 15 major gold deposits with production, reserves and geological resources of approximately 65 million ounces of gold (Figure 1). In the Bluestar/Goldstrike subdistrict, there are seven major deposits; Betze, Lower Post, Post, Genesis, Bluestar, Purple Vein and Deep Star, plus numerous smaller deposits (Figure 2). Production, reserves and resources for the subdistrict are approximately 40 million ounces. Betze and Purple Vein are located on property controlled by Bamck Goldstrike Mines and Bluestar and Genesis on Newmont Gold property. Post, Lower Post, and Deep Star occur both on Barrick and Newmont Property.

Jan 1, 1991

By Rolfe PR, Ellis BA, Clements RJ

Associated Minerals Consolidated Limited (AMC) is constructing a 112,500 tonne/yr synthetic rutile plant at Narngulu, near Geraldton in Western Australia. Design of the plant is based on the technology developed by AMC and utilised in its two existing plants at Capel in Western Australia. Ilmenite Feedstock for the plant will be sourced from AMC's mine at Eneabba and coal obtained from the Collie deposits. The plant is scheduled to come on stream in the second quarter of calendar 1987. The rationale of the decision to construct the Narngulu plant is examined against the background of the world market for high-Ti02 content feedstocks. Also provided is a detailed description of the plant and an examination of the technology used in process Design.

Jan 1, 1986

Portman Mining Pty Ltd very successfully operated the Ferro GullyNorth Mine in the Hamersley Province of Western Australia to satisfy a contract for the delivery of six million tonnes of iron ore in less than two years to the Mount Newman Mining Co Pty Ltd. The high-grade ore extracted from Ferro Gully North Mine was unusual in that, not only was it within the Joffre Member of the Brockman Formation, but it was rich in red ochreous hematite and martite and very low in phosphorus.

Jan 1, 2001

By J Player

Big Bell Mine started experiencing relatively large mining related seismic events, and accompanying rockbursts, from February 1999. Twelve rockbursts damaged access development from February 1999 to June 2000, with severe damage extending for up to 100 m along footwall drives. Five seismic events associated with the rockbursts were recorded by the AGSO, measuring 1.9, 2.2, 1.7, 2.4 and 2.2 on the Richter scale. These events affected 485 and 460 footwall drives in August and November 1999 and 535 footwall drive in June 2000 (drive level nomenclature is equivalent to the depth below surface and RL). After the third event (July 1999) it was apparent that the seismicity was not a once-off phenomenon. This (sudden) onset of seismicity required management to implement a series of precautionary measures:to ensure the safety of the workforce, to maintain continuity of production, and to reduce rockburst damage rehabilitation. The measures included extended re-entry periods and exclusion zones in high-risk areas, improved rockburst resistant support systems in areas prone to damaging seismic activity and improved support systems in areas prone to shakedown damage. A full-scale minewide ISS seismic system was ordered in October 1999 and commissioned in February 2000. A portable eight-channel CSIR-Miningtek system was installed at short notice as an interim measure in August 1999. This CSIR system covered the northern producing stopes, where the majority of the rockbursts had occurred. The objective of the seismic monitoring was to monitor relative activity and to determine trends with regards to time and location. MAP3D numerical modelling was used to investigate the relationship between seismicity and various combinations of stress components to assess the relative seismic risk in both current and proposed working areas. This information is used to determine where and at what stage in the mining cycle the rockburst resistant support is required. Analysis of the seismicity has determined two distinct modes of seismicity û small-scale localised, high frequency events in high stress areas and larger events related to shear along previously intact foliation surfaces. This paper includes a summary of the seismic history, seismic data analysis, support system design, mine design adjustments and management action to minimise the effects of seismic activity at Big Bell Mine.

Jan 1, 2000

By Higuchi K

For the mechanisation or automation of mining, recognition of the shape of mined cavities is basic information. A three dimensional shape measuring system, developed and tested, includes an ultrasonic range finder which is attached to the tip of a serial link manipulator. The range finder can be moved to any position and direction in the operational space of the manipulator. The position of a point on the surface of the object is obtained from the position of the range finder, the direction of the beam of the ultrasonic waves and the measuring distance of the range finder.To avoid collision between the sensor and the object, the manipulator is controlled to trace the surface of the object For the tracing control, another ultrasonic range finder is employed. The test results show that the developed system has high performance.

Jan 1, 1991

The article presents methods of testing and recording of water amount pumped out in surface mining. The authors describe necessary recommendations how to carry out measurements so that one can separate the surface run-off and groundwater inflow from the total inflow. They demonstrate methods of evaluation of these kinds of inflow in open pits when water amount testing is carried out every eight and 24 hours as well as simple methods when only monthly records of water are available. The authors also describe procedures for evaluating the water inflow when an open pit is dewatered gravitationally and measurements in discharge channels are irregularly carried out.

Jan 1, 2003

There are two main areas of application of geology in quarrying: (i) In regional planning for industrial mineral requirements.(ii) In direct quarry management. The regional planning requirement has recently become more evident because of greatly increased land demand conflicts around cities. The direct quarry involvement is a reflection of both the economy and the greatly increased sophistication of the quarry industry. Here, professional planning and development expertise by a geologist is required, to ensure continued supply of raw materials at the best price to the consumer with sufficient profit to the producer. Today, geological insurance safeguards capital investment in plant and assures economical development plans.

Jan 1, 1978

By Weber D, Knox PR

The criteria developed for the Argyle Diamond Mine process plant control system are reviewed. The control system installed is described along with a discussion of the method of implementation adopted. The control system was extensively tested prior to instal- lation at site. This approach led to signi- ficant time savings during plant commissioning and facilitated rapid escalation of plant production. The control system has performed satisfactorily with a high level of operator acceptance and basically satisfies the criteria Developed.

Jan 1, 1986

By Barrett D

The paper discusses the justification for the Open Pit Mining Operation at Central Norseman Gold Corporation Limited's North Royal facility.Open pit mining history is outlined together with production statistics and associated costs. Underground mining practice is discussed together with an outline of the problems with mining in oxidised ground.

Jan 1, 1984

Financial theory often takes some time to penetrate industry and when it does it can result in a paradigm shift in valuations and mental models. The Black Scholes option valuation was first published in 1973, although the authors were only awarded a Nobel Prize in 1997. The valuation of real options has been applied to the oil and gas industry for some time, however it has only recently been more widely applied to the non-oil, mineral resource sector. The use of real option valuation (ROV) for the valuation of marginal and short mine life resource projects is a more useful valuation tool than the conventional DCF, NPV valuation tool. The application of ROV has major implications for corporate strategy. It generally favours equity over debt funding and non-hedging over hedging. A retrospective assessment of the successful development of the Lennard Shelf Operations demonstrates the concepts of implementing real options and the value destruction of limiting operational flexibility through debt and hedging activities.

Jan 1, 2003

Historic mining across the Bendigo goldfield reached an average mining depth of 750 m over an area of about 16 km by 4 km, with two shafts exceeding 1400 m. Mining ceased in the mid 1900s due in part to increased dewatering and ventilation demands. Water extraction technology of the day, combined with multiple mine ownership, did not allow uninterrupted and thus economic mining activity to prosper. Today Bendigo Mining Limited (BML) is targeting gold-bearing reefs beneath the water-filled historic mine workings. To ensure mining activity can proceed without the risk of water inrush, historic workings are being dewatered by submersible pumps in historic shafts and through a series of underground drain holes intersecting old workings. Due to the high heads involved, individual drain hole development requires rigorous safety control implementation and assessment prior to drilling. Water extracted via drain holes is pumped to the surface through a series of pipe lines and rising mains in conjunction with two staged pumping stations. Both stations are equipped with high-speed centrifugal pumps, each capable of pumping 40 L/s at a static head of approximately 300 m. BML, which operates beneath and within a large city, is confronted with unusual environmental and social challenges compared to many within the mining industry. The raw mine water, which contains elevated salt levels, is piped through residential areas and must comply with strict controls to prevent impacts on the surrounding environment. The final delivery point is BMLÆs water treatment plant at the north end of the city. The water treatment plant utilises chemical pretreatment and reverse osmosis. It is able to process 7 ML of mine water per day at full production. The product is approximately 5 ML of reusable irrigation quality water, which is made available to the Bendigo community for public gardens, sporting facilities and rural irrigation. The 2 ML of brine is directed to a purpose-built evaporation pond facility located 7 km north of the water treatment facility.

Jan 1, 2008

By M Miettinen

That microorganisms, both living and dead, and products derived from the organisms, can function as flotation agents and flocculation agents is abundantly clear. They can modify the surfaces of minerals. They can function as flotation collectors and as flotation depressants and activators. In many cases they or their products can function as specific flocculation agents. Problems that must be solved before such microorganisms or products from the organisms can be used in commercial operations include culturing the organisms at a cheap cost and reduction in dosages required for various separations. These tasks are formidable. However, the concept of using such natural materials in place of various chemical reagents that may be toxic is very attractive. An attempt is made to show some of the promise of microorganisms in mineral bioprocessing and to consider the problems that must be overcome before commercial application of the technology is realised.

Jan 1, 2005

By Pollard D, Meadows N

The presence of impurities which are electropositive to zinc in acid zinc electrolyte causes changes to deposit morphology and reduced current efficiency. Glue may be added to control some impurity effects, but assaying for animal glue concentration is difficult and seldom done. Measurement of the activation overpotential for zinc deposition by cyclic voltammetry is used in some plants to monitor electrolyte quality and control glue additions.The deposit morphology and current efficiency of zinc deposition from commercial electrolyte were investigated for various glue additions in the presence of increased levels of antimony. Cyclic voltammetry was investigated as a method of optimising glue additions in the presence of antimony.Scanning electron rnicroscopy showed deposits characteristic of the impurity element present and the glue addition rate. Cyclic voltarnmetry measurements showed some correlation between current efficiency and activation polarisation potential. The importance of using tankhouse electrolytes where results are to be related to tankhouse operation was noted.

Jan 1, 1988

By T Ross, S Cameron

The requirement to use explosives in ground temperatures exceeding 50¦C is becoming more common as mines work to maximise the recovery of their resources. Orica Explosives was requested to assist in the development and implementation of æhot blastingÆ safe working procedures at Liddell Coal Open Cut in the Hunter Valley. The mine operator, Hunter Valley Earthmoving (HVE), had to contend not only with elevated temperatures in their overburden resulting from burning coal beneath, but also old underground workings which tended to exacerbate the problem. The paper discusses the following issues:the consultative process that was used to develop the procedures employed to ensure the process could be carried out safely; the technical issues surrounding blasting in hot ground, including temperature monitoring, product selection, application and design to ensure safety and performance were maintained; the need for confidence and trust in the team that was working together in a potentially hazardous environment, the emotive issues that were encountered and how they were addressed; the value of a regular review process combined with open and honest communication to ensure the procedures represented best practice and that all stakeholders understood the process; and the value delivered to Liddell Coal when sterilised areas of coal became accessible with little disruption to the mining process. The paper also discusses the challenges that were encountered in the Reservoir Block where proximity to major power lines and rail infrastructure meant that hot blasting procedures had to also consider vibration limits and the need for Energy Australia to disconnect the power.

Jan 1, 2001