Search Documents

By Ooms M, Scott OJ

This paper is concerned with the design and operation of storage and discharge facilit- ies for bulk solids handling. It presents an overview of the basic design philisophy emphas- ising the influence of bulk solid flow propert- ies and bin geometry on the flow patterns developed and how these, in turn, affect the reclaim efficiency and the bin structural in- tegrity and wear characteristics of both bins and chutes. The salient aspects of feeder design and operation will be discussed and the need to consider feeders as integral parts of the bin discharge system will be stressed.

Jan 1, 1978

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

The value of water is defined by its marginal utility. Challenges arise where the marginal utility is difficult to estimate. Therefore, when two or more interested parties wish to access water and they cannot use commensurate units for marginal utility; other means of value comparison must be sought. It is asserted here that sustainability principles can be used to guide this valuation if this is supported by a transparent decision framework. This paper proposes that the ICMM sustainable development principles provide appropriate guidance. In addition, a generic framework for decision making is suggested as a complement. Indicators of water management are recognised widely as an integral part of the accountability of minerals companies towards meeting sustainability goals. Less widely recognised are the ways in which sustainability principles can be used to guide decisions on water management which demonstrate growing awareness of its value. This paper illustrates the use of this logic in water issues associated with global sustainability challenges. It then goes on to demonstrate, using examples, that these links exist at all levels of the minerals industry and that indicators of this type are potentially as powerful as those currently being used. The reason for this is that the path from cause to effect is transparent and direct.

Jan 1, 2006

THOSE who have had occ.asion to sample a mine not infrequently find that it is impossible to take their sample cuts at regular distances apart, owing to the ground being close timbered, a stope having been taken out, or some other cause. When such is the case a tedious calculation becomes necessary in order to obtain an accurate result. A conscientious man will make the tedious calculation, but one who is inclined to be lazy, or who does not recognize the importance of accuracy, or has not the time, may be satisfied with either the arithmetical or weighted arithmetical mean result.There are two main systems of taking samples when the cuts are taken-(l) at equal distances, (2) at unequal distances. When the samples are out at equal distances apart there are three methods of computing the assay value :-1 (a) By Arithmetical Mean. The sum of the values and sum of the widths are each divided by the total number of samples, in order to obtain the value and width respectively, no allowance being made for the relative widths arid values. The result isabsolutely inaccurate, and should never be used under any circumstances.1 (b) By Geometrical Mean. The assay widths ie, feet %, feet oz, inch dwt, &c, are added together and the sum of these is divided by the sum of the widths.

Jan 1, 1911

Structure is the most important control on the location of hematite deposits in the Hamersley Province in the Pilbara region of Western Australia. Unravelling the structural history of mineralised areas, however, is complex because the Province underwent three orogenic events, and three regional extension events followed the main episodes of compression. Steeply E to ENE dipping normal faults immediately predated deposition of the Beasley Quartzite of the lower Wyloo Group after the Ophthalmian Orogeny. Steeply NE and SW-S dipping normal faults predated deposition of the McGrath formation of the middle Wyloo Group, following the Panhandle Orogeny. The resulting interpreted rift was subsequently reactivated and tilted during the Capricorn Orogeny. Late NE trending normal faults are confined to the eastern half of the Province. High-grade hematite deposits occur in rocks that range from intensely folded (Mt Whaleback, Giles Mini) to rocks with less, or only little deformation (Paraburdoo, Channar), suggesting that folding had at best limited influence on ore genesis. In contrast, extensional normal faults are always associated with high-grade hematite deposits, and in particular faults that link the underlying dolomites of the Wittenoom Formation with the overlying iron formation, thus providing a pathway for mineralising alkaline fluids.

Jan 1, 2005

By Tucker A. J

An overburden blast utilising horizontal blast holes was successfully attempted at the Ulan Coal Mines during December 1991. The blast reduced operational problems and costs and improved dragline productivity in an area of that contains poorly consolidated sands and clays overlying very hard Permian strata.The fan shaped shot consisted of seven 250 mm diameter holes between 80 and 95 metres long drilled into the highwall face. The holes were loaded with ICI Powergel Gold 25606 bulk Emulsion explosive. The design powder factor was 0.15 kg/bcm for the total shot of 180 000 bcros and 0.44 kg/bcm for the competent Permian strata into which the holes were drilled. Fragmentation from the horizontal blast was comparable to areas conventual blasted. Following the success of this shot further shots are planned for this area.

Jan 1, 1992

By R Balusu, P Humphries

In combination with detailed field studies and goaf gas characterisation, computational fluid dynamics (CFD) models have been used to develop optimum and effective strategies for inertisation during longwall sealing operations to achieve goaf inertisation within a few hours of panel seal-off operation. This study has combined detailed analysis of the performance of various inertisation field trials together with CFD modelling results of different inertisation operations in order to develop the optimum inertisation strategies. A number of parametric studies were conducted on the base case CFD models that had been calibrated and validated based on the information obtained from previous inertisation studies and goaf gas monitoring. These studies included changes in inert gas injection locations, inert gas flow rates, seam gradients, and different inertisation strategies to investigate their effect on goaf inertisation. Studies indicate that the strategy of inert gas injection through the MG seal was not as effective as the alternative strategy of inert gas injection at 200 m behind the face. Innovative inertisation strategies have been developed and subsequently implemented at an underground coal mine in Australia. Further investigations have been carried out in the development and demonstration of proactive inertisation strategies with the objective to suppress the occurrence of spontaneous heatings in active longwall faces, in particular under unexpected scenarios such as during slow retreat/face stoppage due to difficult geological conditions. Initial trials at two Australian longwall panels have demonstrated the great potential of this practice to contain the onset of heatings in the goaf.

Jan 1, 2005

By I Levy

At our Monkland Mine at Gympie, we operate a deep, narrow vein gold mine using hand held equipment, rail mounted haulage and narrow shafts. This is in many respects the old-fashioned way and is well suited most of the orebody geometry exposed to-date. We have also commenced some long hole stoping and we use alimaks for some jobs. The heart of our particular mining style is the employment and retention of experienced miners with remuneration based on productivity. We do our planning/monitoring/supervision down to the level of daily individual productivity. In focussing on cycles per se, we have chosen not to talk about drill and blast cycles or cycles for mine development, stope preparation or drawdown and haulage. Instead we have stepped right back from the operation as presently run and have adopted a very broad view of the mining cycle. We will in this presentation intertwine the ebb and flow of, exploration, project sponsorship, development, production and cash returns to owners. The time line considered spans both history and predicted future.

Jan 1, 1998

Kamhalda is located within the Yilgarn Craton of Western Australia, specifically in the Norseman - Wiluna greenstone belt. Numerous nickel sulphide deposits have been mined at Kambalda with I I mines currently operating. For several years, a program of in-mine geophysics has been operating at Kambalda, with downhole electromagnetics (UHEM) one of the key techniques used. Three case studies illustrating the uses of UHEM in mines are presented here. In the first example, the Helmut South deposit was discovered as the result of an extensional exploration program. The first drill hole in the program intersected ore width and grade mineralisation at around 760 in depth. Two subsequent holes intersected subgrade mineralisation. DHEM surveys were completed in each of these three holes, with anomalies recorded indicating that a large conductor was located directly south of the first hole. The next hole intersected this target, for an intersection of 21.6 in at 3.5 per cent Ni. DHEM continued to play a role as the exploration program proceeded, providing drill hole targeting based on anomalous responses recorded in each drill hole. In the second example from Carnilya Hill, old drill holes were surveyed with DHEM in order to search a large section of prospective contact for massive ore pods. An off-hole anomaly was detected and subsequent mining discovered a small but high-grade pod of ore which was extracted for a considerable profit. Carnilya Hill has limited reserves and discoveries such as this, assist in keeping the mine operating. In the third example from Victor, a program of drilling intersected thin ore profiles in an interpreted flanking position. Without massive ore close by, these intersections probably do not constitute economic mineralisation. DHEM surveys of three holes did not detect any conductors. The area is now regarded as sterilised of significant massive ore and exploration efforts and dollars can be focused in other areas. These three examples demonstrate the type of successes that can he achieved through the use of DHEM.

Jan 1, 1997

Present value maximisation studies are a useful aid in enhancing the economic performance of open pit mining operations. Maximising present value helps to reduce the risk of financial failure. Maximisation of present value also means that the capital invested is being used most efficiently. A characteristic step in determining the present value of an open pit mining operation is to set out the sequence in which increments of material (ore of various grades and waste rock) are mined. Traditionally, present value maximisation has been performed by selecting a cut-off grade for each increment so as to maximise the present value of the total operation, by an iterative process using computers. Kenneth F Lane has developed a method and applied it to many mining operations. An alternative method for determining the maximum present value of an open pit mining operation is given. In this method the maximum present value is determined by working backwards from the end of the operation life, progressively asking the question of each increment `what cut-off grade maximises the the present value at the start of mining of that increment?' The method allows calculations to be performed by a `spreadsheet' package. Present value determinations are characteristically performed under constant conditions (eg prices, costs) throughout the operation life. Unfortunately real life circumstances are rarely constant, with the costs of mining inputs rising at variable rates. The prices received for mineral products have been shown to broadly trend downwards with time in real terms. Treatment of such changes in the determination of the maximum present value of an operation is discussed.

Jan 1, 1994

The first continuous pressure disk filter took up industrial-scale operation in Germany in 1976. This paper comments on major components of pressure filter facilities from the point of view of industrial-plant suppliers. For lack of time aspects of economy have not been commented upon. The paper elucidates a number of process-engineering inter-relations. It outlines important development trends from the angle of a machine-building company.

Jan 1, 1989

By Kajioka H, Nakamura Y

Na2CO3 is a powerful flux for both dephosphorization and desulphurization in oxidizing atmospheres. In order to study refining with Na2CO3 and the nature of the Na2CO3 slag itself, hot metal (4Kg) was melted in Al203 crucibles in a high frequency induction furnace and oxidised with oxygen under Na2CO3 slag. The behaviour of Na2CO3 at high temperature was observed by thermobalance. It was found that dephosphorization ceases in a few minutes and [,P] after refining is easily lowered to less than 0.010%. [%P] after refining is affected by [Si], [P] of hot metal, the refining temperature and the consumption of Na2CO3. Desulphurization also ceases in a few minutes but it shows curious behaviour, increase of [S], decrease of (S) and increase in sulphur lost, during the latter half of run. [%S] after refining is also affected by [P] of hot metal, the refining temperature and the consumption of Na2C03o

Jan 1, 1980

By Gardavsky V, Gabell AR, Green AA

The I,)hyllosilicate mineral chlorite is a common constituent of altered rocks associated with volcanogenic massive sulphide deposits, and literature studies indicate that, in general, this mineral is progressively enriched in magnesium relative to iron as an orebody is approached. Studies have shown that there is a direct correlation between the Mg/Mg + Fe ratio of chlorite and its absorption spectra in the 2.7 to 3.0 um range. However, this region, which contains the fundamental 0-H stretch absorption features, is affected by intense atmospheric absorption, and therefore cannot be used for remote sensing. At shorter wavelengths (0.4 - 2.5um), there are windows where the atmosphere is sufficiently transparent and vibrational absorption bands still occur, although they are clue to overtones and combinations, and accord- ingly are much weaker than the fundamental features. Shifts to longer wavelengths with increasing iron content can still be observed in this region of the spectrum and, with better spectral resolution and sensitivity, it may be possible to monitor subtle variations in chlorite chemist by remote sensing techniques.

Jan 1, 1987

By Glenn R. J

Treatment processes are outlined for the recovery of rutile and zircon from the heavy mineral-bearing sands on the east coast of Australia. With the exhaustion of the higher grade deposits and the imposition of more rigid specifications for the finished products, strict metallurgical control has become necessary.A description is given of the methods used by The Titanium Alloy Manufacturing Co. Pty. Limited to control the operation of suction dredging, of wet concentration using fans and spirals, and of dry separation using high tension and electromagnetic processes. By applying these methods a plant designed for an output of 15,000 tons of rutile per year has been tuned to produce over 20,000 tons of rutile and a corresponding amount of zircon.Details are given of (a) the method of drilling to determine the extent and grade of the ore bodies, (b) a simple electrically-timed pneumatic automatic sampler, and (c) the methods developed for the physical estimation of quartz, rutile, zircon, ilmenite and "others" in the products of plant operation.The method used for calculating the metallurgical balance and the forms used for the reporting of production results are presented.Examples are given which show the value of this detailed production and metallurgical control of plant operation.INTRODUCTIONThe organization which is now known as "The Titanium Alloy Manufacturing Co. Pty. Limited" (T.A.M.Co.)-a subsidiary of National Lead Company-commenced operating at Yamba, N.S.W., in 1935. A mixed natural concentrate was at first simply dried and bagged and later was upgraded by the removal of silica and the lighter heavy minerals on shaking tables and, after air-drying, was bagged for export. At that time zircon was the most wanted constituent.

Jan 1, 1960

By Wilson AC

Permian coal from Western Australia's only producing coalfield at Collie is the dominant fuel used in generating electricity for the State's interconnected grid. Collie coal is sub-bituminous, non-coking and has a low ash, medium volatiles and high moisture content. The seams were laid down in a fluvial basin which extended beyond the Collie Basin and included the Wilga and Boyup Brook Basins at least. Adjacent parts of the southwest Yilgarn Block are prospective for Collie-type basins. In the past few years significant deposits have been delineated within the Perth Basin, specifically on the Vasse Shelf and in the Hill River area. In the former area high quality steaming coals are correlated with the lowest coal bearing member at Collie. The seams are amenable to underground mining and because of their high quality, the coal may have export potential. Sub-bituminous coal deposits of Jurassic age are present in the Hill River area. Exploration has down-graded the prospectivity of the Carnarvon and Canning Basins for sub-bituminous near-surface coal deposits. Tertiary lignite deposits are present in palaeo-drainage systems in the southern part of the State and their potential for development is being evaluated.

Jan 1, 1986

This paper addresses; land use, rehabilitation and the State/Federal regulatory process, in light of Australia signing various international conventions and agreements in the area of environmental protection. The conventions on biological diversity, climate change and the implications of the Rio and Agenda 21 declarations are examined. The implementation of these initiatives through the Inter-Governmental Agreement on the Environment, and through legistlative mechanisms at Federal and State level is explored.Particular attention is given to the biodiversity strategy in context of the need to integrate economic aspirations and environmental concerns as a basis for sustsainable development. The paper concludes with a brief comparison of the major approval processes in each State, relating to mining environmental issues.

Jan 1, 1992

The Olympic Dam mining operation is some 520 kilometres NNW of Adelaide on the Roxby Downs Pastoral lease. The deposit containing copper, uranium, gold and silver was discovered in 1975 by Western Mining Corporation (WMC). A joint venture was formed in mid-1979 between WMC (51 per cent) and British Petroleum (BP, 49 per cent) for the development and exploitation of the deposit. WMC assumed 100 per cent ownership after acquiring BP's share in early-1993. Ore is won from a highly mechanised underground mining operation and processed to refined products. Current annual output from the mining of 3.0 Mt of ore is approximately 83 500 t of refined copper, 1400 t of uranium oxide, 750 kg of gold and 12 000 kg of silver. Conventional long hole, open stoping techniques are used to extract the production ore. Since stope production began in April 1988, full surveys and appraisals of stopes have been carried out to evaluate the integrity of the design and blasting techniques. This evaluation included the determination of the degree of dilution or non break that had occurred. Performance information also made it possible to re-design any adjacent stopes to retrieve remaining ore and conversely, avoid the chances of targeting backfilled material in the future. Performing stope surveys proved not only to be a time-consuming process but one fraught with access and line-of-sight problems. Occasionally it was not possible to obtain any stope survey data, and as was often the case with the mine pass system, rarely. In 1992 the sudden failure of the pillar between the fine ore and mullock passes and the subsequent delays to production, emphasised the need to effectively monitor pass wear. Initial information regarding the development of the Cavity Measurement System (CMS) prototype (Figure 1) indicated that it had the potential to solve these problems by the introduction of a remote scanning device into a cavity. Following a great deal of investigation, Olympic Dam Operations purchased the first CMS in Australia. This paper discusses its application for all underground void surveys and the procedures developed to manage both field and office requirements.

Jan 1, 1995

By A D. Ferreira, A E. C, A D. Padovezi

The increasing market requirements regarding the quality of products, the enhanced predictability from detailed mine planning, the need for process consolidation and upgrading require continuous investigation on the characteristics of different ore types to be concentrated. This paper addresses the mineralogical and technological characterisation of several itabirite iron ore types and the influence of the composition and mineralogical associations on desliming and flotation. Pellet feed quality and the influence on the major performance indicators, such as weight recovery of slimes, selectivity index, metallurgical recovery, flotation kinetics of iron minerals and gangue is also emphasised. The investigation resulted in a classification of iron ores according to their mineralogical composition, morphology of the crystals, and/or texture and microstructure of mineral particles with respect to desliming and flotation performances.

Jan 1, 2005

By Fernando N, Guang LX

Brown coal in Victoria in spite of its substantial reserves is not utilized greatly because of its high moisture content(-65% w/w). Transportation and handling costs of raw brown coal, on an available energy basis are so expensive that 93% of production is burnt for electricity generation on or adjacent to the coal deposit in Victoria. With direct firing of moist brown coal in power stations, approximately 20% of the gross calorific value of the fuse is used to evaporate the water contained in the coal. This energy is lost as vapour with the flue gas which is vented to the atmosphere. Also there is a 25% increase in flue gas volume and the size and cost of most of the units through which it passes must be appropriately larger. Since there are large quantities of water present the flame temperature is significantly reduced. For zero excess air and no air pre-heating the theoretical flame temperatures are: 609'o wow moisture 1450¦C 40% ª ª ª 1790¦C ZOO ª ª ª 1990¦C As a result of this there is a reduction in radiant heat transfer leading to a requirement for a two fold increase in radiant tube area. A boiler of much greater size and cost is thus required to house the additional tubes. Figure 1 illustrates the relative sizes of a boiler fired with 60% moisture brown coal with a boiler or similar output fed with a British bituminous coal, 14% moisture.

Jan 1, 1989

By Giedl JG

Technical applications of computers within the coal industry are expanding rapidly with an increase in the number of users and user locations. Collinsville Coal Company Pty Ltd is an example of a remote and growing user company which has a Telecom link to MIM's ICL mainframe computer in Brisbane. The Planning Department is one of the technical user departments at Collinsville, with a variety of VDU, plotting and screen graphics hardware supported by the MIM Computing network. Current applications involve the storage, retrieval and manipulation of borehole information, plan and map production, volume calculations from survey data and mine ventilation modelling for underground Operations.

Jan 1, 1983