Search Documents

By M Scoble

This paper is based upon the experiences of collaborating academics in two mining schools and their personal view of attempts to integrate the principles of sustainable development into mining education and research. In this quest, the concept of sustainable mining practices is proposed, not only relating to environmental, social and economic performance but also stressing mine safety and efficiency. These practices need to support strategies that enable flexibility and resilience within mine operations to counter recessionary cycles. Also, these counter-cyclical strategies are now imperative for sustaining mining education and research itself. There is a critical interdependence between these two different perspectives on æsustainabilityÆ. The paper concludes by demonstrating models of strategies that promote inter-disciplinarity, collaboration and networking for sustaining mining schools.

Jan 1, 2009

By Lewis RW, Tullemans FJ, Gallo JB

Gold mineralization at Kidston occurs in a semicontinuous zone near the margin of a large, late Palaeozoic breccia pipe. The pipe is ovoid in plan, funnel-shaped in cross section and straddles a contact between Proterozoic metamorphic and granitoid rocks which are intruded by a swarm of late Palaeozoic acid dykes. Rock fragments within the breccia pipe reflect the enclosing country rocks and mix in various proportions to form gradational lithological domains. Most of the gold is free and is located in the breccia matrix and in a set of inwardly dipping sheeted quartz veins which kink around the pipe margin. Sulphide minerals, dominantly pyrite, occur as disseminations in the breccia matrix and as aggregates in the cores of quartz veins. Hydrothermal altLration is pervasive within the breccia and is most intense in areas with the highest percentage of acid dyke fragments. Sericite and carbonate are the main alteration minerals. An empirically developed genetic theory for the formation of the breccia pipe and attendant mineralization involves magmatic and post-magmatic processes associated with the intrusion of a granitoid body to a shallow level in the crust. Economic evaluation of the deposit relied heavily on the results of diamond drilling. Both polygonal and geostatistical reserves were calculated and found to be in close agreement. Geostatistical reserves are considered to more closely reflect the tonnes and grade achievable during mining. Daily geological mine routine is strongly biased towards grade control allied with the practical aspects of open-pit mining. Tonnage/ grade correlations between ore blocks geostat- istically generated from exploration diamond core results and ore blocks generated from high

Jan 1, 1986

In Australia 'there are hidden deposits of gold, copper, tin, lead and zinc which can be found by drilling at reasonable expense in view of the imp9rtance of the objectives. Exploration of the prospects in mind would mean about a million feet of drilling. The purpose of this paper is to outline, in a technical way, some of the geological thinking that has been given to this matter. To do this, it is necessary to unify the wider ranging thoughts into some sort of coherent perspective and also into some sort of logical sequence. This will be done by treating first the geological subject material which is in fact, at the foundation of the exploratory scheme. With this base, the argument will be continued through a sequence of prospect thinking and brought to a conclusion in regard to the practical employment of geology in the drilling planning. In this knitting together of ideas, the discussion will be given substance by welding into the argument the reasoning that has been applied to the Cobar prospect. The New Occidental Gold-Mines are operating three mines at Cobar, and the writer is indebted to the Company for allowing the reference to be made. It is intended, as opportunity permits, to furnish further examples in later publications.FOUNDATION OF EXPLORATIONThe deposits under consideration are derived from igneous rocks, chiefly granite or porphyry. In and following the emplacement of the intrusives, the rocks have been...

Jan 1, 1946

By P Lamberg, M Lyyr, S Heimala, J Liipo

Since the introduction of froth flotation for industrial practice, the process has long been developed and improved by making cultivated guesses or by using trial and error methods to a varying degree. Fresh possibilities have emerged after development of new surface sensitive analysing methods and in situ electrochemical methods. Having had the possibility to combine different findings between science and everyday plant practice, Outokumpu has been able to develop a catch-all procedure to manage a flotation process taking into account the specific requirements set by different minerals in a slurry. A number of these procedures are available and offered globally to clients as part of a Plant Audit service. The Outokumpu Plant Process Audit (Process ef-X) concept comprises of mineralogical determinations from process samples and plant data analysis together with electrochemical process measurements using mineral electrodes. Automatic control loop analysis can also be included. The objective is to combine the results for a basis of flotation process improvement. Since this methodology has earlier been an in-house practice, it follows that the results are also reflected in the development and design of the OutokumpuÆs processing equipment. An increasing number of ores have a very intimate fine-grained texture and it may be physically impossible to combine high grade with acceptable recovery by a flotation process alone. For such cases, combinations of different hydrometallurgical û mineral separation û pyrometallurgical processes are available. Mineral specific information and chemical expertise of flotation technology can be utilised in development of other processes, as well.

Jan 1, 2005

By E R. Ramanaidou

The presence of clays in channel iron deposits (CID) within the Pilbara region of Western Australia causes problems in the classification and subsequent processing of the iron ore. In particular, the presence of clay adversely affects the processing and ore metallurgical properties by increasing the amount of Si and Al. Iron ore companies are seeking new methods to quickly and objectively detect the type and amount of clay in these deposits. Traditional methods of clay quantification such as X-ray diffraction (XRD) and thermal analysis are time consuming and expensive. Reliance on bulk chemical techniques (eg X-ray fluorescence, (XRF)) to derive normative mineral abundances can give misleading results. For example, the replacement of Fe by Al in the structure of the iron oxide minerals, goethite and haematite, which dominate in CIDs, can be significant. Silicon can also occur in association with these Fe minerals. If not accounted for, chemical techniques may overestimate the normative abundance of clays. In comparison, reflectance spectroscopy in the visible-to-near infrared (VNIR) and short wave infrared (SWIR) wavelength range (eg 400 - 2500 nm) and Fourier transform infrared (FTIR) (6000 - 900 cm-1) analysis are non-destructive techniques that can provide rapid and objective mineralogical information. Both techniques are particularly suited to Al-, Fe- and Mg-OH bearing minerals such as clays. Kaolinite and, to a lesser extent, montmorillonite are the most common clay contaminants that occur in the Pilbara CIDs. Previous applications of VNIR-SWIR spectroscopy have demonstrated the potential of these methods in quantifying the clay mineralogy of CID ore. In this study, variations in the depth of diagnostic spectral adsorption features in the SWIR wavelength range of kaolinite and montmorillonite in standardised mixtures, with known proportions of clay, were well correlated to the abundance of kaolinite and montmorillonite, and to the clay alumina content (ie per cent Al2O3 û clay).

Jan 1, 2007

By M S. Powell, M P. Bueno

The commonly used SAB, SABC and run-of-mine (ROM) ball mill circuits can achieve high throughputs with good operating stability. However, these circuits consume a substantial amount of grinding media, which can have a substantial impact on the OPEX and the æcarbon footprintÆ, specifically when viewed as an æembodiedÆ energy input. On the other hand, fully autogenous (AG) circuits can operate at much lower operating costs, but with limited throughput. The control of AG mills, fed by ores with hard and soft components, can also be challenging, due to the sensitivity of the mill to the ratio of hard to soft components.In this paper, a multi-component modelling approach was used to demonstrate that the harder component should be used as grinding media, and its use should be kept to a minimum to avoid reduction in the mill throughput. There is an optimal blend of hard to soft, and any optimal blending condition is both ore-dependent and mill-specific. Establishing this blend is challenging, and consequently discourages the use of autogenous mills. The new modelling approach addresses this challenge by providing a quantitative prediction of the influence of blending soft and hard components in a mill. This prediction can then be used to establish the required blend for maintaining a stable and efficient operation in autogenous grinding mode.CITATION:Bueno, M P and Powell, M S, 2012. How to use hard ore components as grinding media, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

The re-development of the Mount Charlotte gold mine in Kalgoorlie was carried out piece- meal as funds became available. Optimisation of productivity to offset the high risk which is a function of an indefinite gold price, has been the principal objective of the management.

Jan 1, 1980

By Bevilacqua P, Preti U

The basic separation phenomena taking place in film concentration processes are studied through a kinetic-probabilistic approach. This approach is based on the fact that the particle velocity in the film separation phenomena is a random variable and may be defined by frequency distributions and probability laws. The approach requires: 1. development of probabilistic models for describing the behaviour of particles having different specific gravity and size along selected trajectories in the separating devices; 2. setting up an experimental procedure for determining the relevant frequency distribution curves at the exit of the separators for the particles mentioned above; 3. estimation of model parameters and model validation. In the paper, the model equations are given for the mass distribution of particles on the surface of separators, the mass distribution at the exits of shaking tables and the residence time distribution in channel type devices. The relation between residence time distribution and particle velocity distribution is derived. The test procedure has been defined and results are reported for the exit or residence time distribution in channels. A comparison between experimental and calculated frequency distributions is reported.

Jan 1, 1993

A low grade, refractory ore gold mine with high striping ratio such as at Macraes is always challenged in ways to improve margins. Common practice approaches used at OceanaGold Ltd Macraes are to maximise grade delivery, optimise recovery and reduce unit costs, as well as take any opportunities to incorporate new technologies and implement enhanced commercial strategies.   The Business Improvement (BI) programme was implemented across the Macraes operations in late 2003 and is being rolled-out to all other parts of the business. The core focus of BI at OGL is to: +        increase revenue, +        reduce cost, and +        improve processes.   A dedicated BI team comprising of a manager, team leaders and business analysts were engaged to identify and manage a series of opportunities to reduce operating expenses, optimise capital outlays and generate extra revenue. The Business Improvement Programme, though in its formative phase, has begun a cultural change within the organisation. Many people are starting to challenge the way they do things and are looking for ways to continually improve business performance.   The BI team encompasses individuals from different departments who can offer the diverse skill set necessary to produce intended results. The current team is made up of a BI manager, BI Team Leaders in Mining and Processing and analysts from Mining, Processing, Commercial and Plant Maintenance workgroups. A team member has recently been formally trained as a Six Sigma Black Belt. ] The BIÆs team role is to assist in the establishment of project management processes for each improvement idea. In addition the team will assist in tracking implementation, identifying and unblocking restrictions and limitations as well as setting up metrics to quantify the level of benefit returned and sustained.   From a more strategic point of view, the BI team is advancing the Business Improvement capability of the company by developing long term Communication and Training strategies. These strategies will set the direction of BI initiatives in the years to come to: +        educate the OGL workforce in basic BI techniques, +        assist the OGL workforce in applying basic BI techniques, +        communication the direction of BI in OGL, and +        close the information feedback loop to facilitate transparent communication between the OGL workforce and the BI team.

Jan 1, 2004

By Hedge AS

Mt Whaleback is one of the largest open-cut iron ore mines in the world. Haulage cost is the single largest component of operating costs at the mine. Past studies towards alternatives to truck haulage have recognised the potential viability of an in-pit crushing and conveying system, dependent on the proportion of uphill haulage. After seventeen years of mining Mt Whaleback still contains more than 1,000 million tonnes of ore, needing 1,800 million tonnes of waste removal to extract it. What was once a quarry has now turned into a large open pit. The increasing proportion of uphill haulage, the need to replace ageing 120 ton and 200 ton trucks and the necessity of achieving and maintaining a higher stripping ratio prompted, in 1984, the initiation of a new feasibility study into the viability of alternative material handling systems. A semi-mobile in-pit crushing and conveying system was found to be most suited to Mt Whaleback conditions. The East Pit was selected as the best location based on the analysis of haulage profiles measured on long term incremental mine plans. A capacity of 22 million tonnes per year was considered achievable by the proven technology currently available. A detailed estimation of capital and operating costs of two systems - one with trucks only and another with trucks, crusher and conveyor - for the removal of 22 million tonnes per year of waste rock, showed substantial cost savings achievable by the proposed system. An economic evaluation of the two systems established the advantages of constructing the in-pit crushing and conveying system. This is now under construction and will be commissioned in early 1987. Experience gained in constructing and operating this installation is expected to influence decisions on similar installations in future.

Jan 1, 1986

By C Zhang, I Canbulat, S Saydam, H Yu, H Chen

Natural rocks are frequently exposed to groundwater and complex geological conditions. Environments with water presence are more susceptible to chemical corrosion, which notably affects rock’s micro properties. Generally, the pH of acid mine drainage in hard rock mines can be low to 5, and the pH of quarrying waste deposits can be below 3. With the expanding scope of mining engineering in aquifers and salty areas, chemical corrosion can also caused by different types and concentrations of anions. The anions can significantly affect rock’s mechanical properties. Therefore, it is critical to emphasise the impact of anion and acid on the mechanical and micro characteristics of rock. This paper commences with an introduction to representative corrosive environments. Then the UCS tests are conducted on granite samples corroded by chloride ions and sulfate ions. Anion has negative effects on the strength of granite. The reason is that certain minerals can react and be dissolved by anions and hydrogen ions, such as Al2O3. Furthermore, the scanning electron microscope (SEM) shows that the roughness of the fracture surface increases with the anion concentration. The effect of acid is notably more pronounced than anion on the micro properties of granite. The initiated fissures and pores also increase with the concentration of SO42- and Cl- ions, which is the micro explanation for the impact of anion on rock strength and stability. Subsequently, the permeability of the granite specimens is tested. The reason that granite performs insensitivity to acid and anion is attributed to its low permeability and high content of inactive oxides, such as quartz. To summarise, anionic and acidic conditions can slightly deteriorate the mechanical and micro properties of granite. While SO42- demonstrates a higher level of corrosiveness on granite than Cl-.

Sep 1, 2024

By Andrews JRG

Chrysotile asbestos is a valuable resource. Used as a reinforcement in asbestos cement, products are obtained which are cheap, are not attacked by vermin, do not rot or support growth of fungi and are unaffected by water or humid conditions. Such products are of great value in the developing countries where inexpensive and durable building materials and pressure pipe are very important to development, housing and water supplies. Concern over the adverse effects of inhaling asbestos has led to the introduction of increasingly stringent controls world wide on the quantities of airborne asbestos per- missible in the occupational situation. Wet processing has the potential for virtually eliminating the environmental concerns with asbestos dust both in fibre production and in the materials handling section of the manufac- ture of asbestos cement products. In addition, high efficiencies associated with wet process- ing mean that better yields are obtained and that the tailings which are dumped have a lower residual asbestos content. Since early 1977, ICI Australia and Woodsreef Mines have been engaged in a programme of research to develop and evaluate a wet mill- ingprocess to produce, from ore and existing tailings, high grade fibre suitable for use in asbestos cement products. The process has been developed through microscopic studies, labora- tory bench scale experiments, work in a small scale semi-continuous plant and product evalua- tion on experimental size Hatschek asbestos cement machines. A prototype mill with a normal feed rate of 1z tonnes per hour and capable of producing pipe grade asbestos from Woodsreef ore has been constructed and was operational from January, 1982 to July, 1983. A range of asbestos cement products have been made successfully on full scale Hatschek machines using fibre from ore and tailings milled in the prototype mill. Economic evaluations indicate that a wet process mill would be cheaper to build, operate and maintain than an equivalent dry process plant. A commercial plant has been designed 1. Manager New Process Development, Woodsreef Mines Limited, Barraba, Australia. 2. Senior Lecturer, Department of Chemical Engineering, Monash University, Vic, Australia. formerly Senior Research Officer, Research Department, ICI Australia Limited

Jan 1, 1986

By Stein A

The general mechanism of recrystallisation for cold worked metal is well established, and need be only briefly summarised with a few references to recent articles which clarify minor points. The types of extension, whether by stretching, drawing, hammering, rolling, etc., do not alter the general principles (1), although quantitative results may differ somewhat, particularly with regard to differences between the surface and interior of samples.These principles can be summarised as follows: The first stage in annealing is a recovery (sometimes known as relaxation) of physical properties such as hardness, elongation, etc., without any appearance of recrystallisation; the second stage involves a further alteration in physical properties, accompanying the formation of new recrystallised grains which replace the original structure; a possible third stage involves an increase in the grain size of the completely recrystallised structure by absorption of smaller grains by larger ones. These three stages will be referred to as recovery, recrystallisation, and grain growth. Depending on conditions, the three stages may be clearly marked or may occur more or less simultaneously.For a given annealing temperature, cold deformations below a certain amount fail to give recrystallisation, and the final structure consists of the original grains which have recovered and possibly become more equiaxed. When a certain deformation, critical for that annealing temperature, is given, recrystallisation can occur, and will give the maximum recrystallised grain size.Increasing deformations beyond this give progressively smaller grain sizes.For each material there is a minimum recrystallisation temperature, below which recrystallisation will not occur whatever the deformation or time of annealing. For a given deformation there is a temperature, critical for that deformation, below which recrystallisation will not occur, and above which it will take place with increasing rapidity.

Jan 1, 1947

By S A. Prevec

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Traditional models employed to genetically link associated chromite and platinum-group elements have favoured crustal contamination as the primary process for inducing sulfide and oxide saturation. The association of chromite ores with crustal contamination is well established in the literature. However, in the 1970s (cf Irvine, 1973, 1975), Irvine demonstrated that crustal contamination was in fact problematic as a tool for inducing chromite precipitation in mafic to ultramafic magmas. His results are re-examined here, along with some attempts to reconcile them with the effects of adding Fe to the models. It is concluded that crustal contamination is indeed problematic based on phase relationships alone. However, the role of fluids as a compensating agent is evaluated, which may explain why crustal contamination may indeed facilitate oxide and sulfide precipitation.CITATION:Prevec, S A, 2015. Chromite and platinum-group elements coprecipitation by crustal contamination or magma mixing revisited – genetic and exploration implications, in Proceedings PACRIM 2015 Congress, pp 311–316 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Baafi EY

Open cut mining in Australia is facing the greatest challenge in its history in attempting to compete not only with other operations internationally, but also with underground operations domestically. Most flat dip and shallow depth surface-mineable coal reserves have been depleted during the last two decades and new open cut operations must extract deeper coal deposits. As open cut coal mines move into deeper areas and the stripping ratios increase, the relative cost of overburden removal also increases. It therefore becomes even more important to design the mine around the optimum overburden removal scheme. The deeper mines are usually multi-seam operations with a more complex geology and with more geotechnical and hydrological problems. Deeper mines are subjected to greater problems requiring more detailed mine planning and design, such as selection of the optimum mining method and pit layout. In planning and design of such operations, the number of alternative methods which need to be considered is consequently greater.Dragline productivity and its stripping capabilities are directly affected by the selection of digging method, strip layout and pit geometry. Every mine has a unique combination of geological conditions. The operating methods that work well at one mine may not necessarily work at another site. Selection of an optimal stripping method, strip layout and pit geometry for a given dragline must be considered with respect to the geological conditions of the mine. With increasing geological complexity of Australian strip mines, it is becoming more important to use sophisticated techniques such as computerised mine planning methods to assist in optimising dragline operations.

Jan 1, 1998

By Mason D. O, Tuckwell K. D

Whole rock geodhemical analyses from samples of Potosi gneiss within the Willyama Supergroup have been utilised to identify geochemical trends towards Pb/Zn ore positions. Although the analyses come from disparate sources they have been incorporated in the data base only if locational, sampling, analytical, lithological and stratigraphic descriptors were reliable. These data have been statistically analysed using programmes of the GASP software package. A discriminant function has been derived which permits Potosi gneiss associated with the Pb/Zn lode horizons in the Broken Hill domain to be distinguished from Potosi gneiss in a similar stratigraphic position in the Maybell Domain. In the "near ore" position the Potosi gneiss has significantly lower mean Na2O and significantly higher mean MnO. Also mean Rb, CaO and K20 are higher and mean Sr lower. This discriminant function serves to identify areas prospective for Pb/Zn mineralisation. A second discriminant function based on MnO, Si02 and K20/Na20 gives a semi- quantitative indication of proximity to ore.

Jan 1, 1983

The major slime forming minerals in coal seams are generally montmorillonite, illite and kaolinite, and due to the consistant trend to full seam mechanisation in New South Wales and Queensland these minerals remain in the feed to a coal preparation plant. After coming into contact with water their size degradation is very rapid, and therefore they mostly report to the fine coal cleaning section of the plant. Froth flotation, being the most effective method of beneficiating fine coal, is widely practised in these two major coal producing states of Australia. Plant experience and laboratory tests suggest that the presence of these slimes in the flotation circuit depresses the flotation of fine coal. Although the deleterious effects of slimes on the flotation behaviour of minerals is well known, the mode of their adsorption at the mineral surface has been a subject of controversy for some time. In this paper, on the basis of the surface properties of slime forming minerals and coal, a model has been put forward to explain the adsorption of slimes at the coal surface. The degree of slime coating has been examined by scanning electron microscopy. Laboratory tests have revealed that with the appropriate use of polyvalent phosphate electrolytes these slimes can be liberated from the coal surface. Just attrition and desliming are not enough to ensure complete liberation of slimes. Coal, after treatment with these electrolytes and then deslimed, floats readily with a common frother, such as MIBC. Modifications in the conventional flotation circuits have been suggested to ensure an efficient flotation of fine coal.

Jan 1, 1978

The world is getting flatter through internet, mobile phone technology, relatively low cost travel, massive outsourcing of manufacturing to China and the transfer of company backroom operations to India. In the iron and steel industry, however, things will remain relatively the same with slow gradual improvements in technology; only the geographic location of plants may change over time. Or will it? The blast furnace smelting process has remained largely unchanged since 1828 when James Neilson came up with the idea of preheated air being delivered to the tuyeres. Likewise, oxygen steelmaking that takes molten iron from such blast furnaces has remained conceptually unchanged since Sir Henry Bessemer invented an air-based system in 1856. These two processes are the core of integrated steel mills that we know today. Typically such mills consist of coke ovens, sinter plant, blast furnace, oxygen steelmaking, continuous caster, rolling mills and metal coating lines. In the intervening 150 years the only real disruptive technology to the integrated steel mill has been the minimill. Based on the use of the electric arc furnace (EAF), in conjunction with a continuous caster and rolling mill, the term minimill is used because steel products are produced at down to one-tenth the scale required for economic operation of an integrated mill, with the EAF producing molten steel using largely scrap steel as its feed, as against transforming coal to coke (coke ovens), iron ore, coke and limestone into molten iron (blast furnace) and molten iron to steel (oxygen steelmaking). There are, however, a number of technologies in development that may cause a paradigm shift in the way steel products are produced and perhaps push the evolution of the minimill as a disruptive technology. Two examples are direct iron smelting, where iron is produced in a matter of seconds by injection of ironmaking feed materials into a molten bath, and thin strip casting, where molten steel is cast into 2 mm strip or less, in similar time. Both have Australian connections. A leading iron smelting technology is the HIsmelt« process, which has its first commercial application at Kwinana, Western Australia, where a joint venture of international parties, consisting of Rio Tinto and the Nucor, Mitsubishi and Shougang corporations, are in the stage of ramping up commercial production. The leading strip casting technology is the Castrip« process that arose from development work done by then BHP Steel, with IHI of Japan, at Port Kembla, New South Wales in the 1990s. Nucor followed this work up, building the first commercial plant for the technology at its Crawfordsville site in Indiana in 2001 and has recently announced an intention to build a second plant in the USA. While both technologies are only into the early stages of commercialisation they are likely to change the face of iron and steelmaking as we know it over the next 20 years. This paper elaborates on the technology of the two processes, why they could change the face of the iron and steel industry forever, what might drive the rapid change and what the changes may look like.

Jan 1, 2006

By Y Tsukurimichi, D Asahina, T Endo, T Takemura

Scientific knowledge of Mars’ surface morphology and internal geological structure has been accumulated through satellite imagery and numerical topographic data using remote sensing technology, as well as seismic surveys by the on-site lander. Recent studies show that Marsquakes could be caused by the release of strain energy generated by the contraction of Mars. In particular, Marsquakes occur around the graben where many faults are existed and formed regularly spaced patterns. This implies that Marsquakes occur when the stress field of the Martian crust is an extension condition, and normal faults appear on the surface. We focus on the linear relationship between the fault spacing and the thickness of the mechanical layer as an approach to studying the internal structure from satellite images. Mechanical layer is a layer that composes of the same mechanical properties and is mainly bounded by lithology (Narr, 1991; Gross, 1993). The linear relationship between the thickness of the mechanical layer and the joint spacing has been studied and its slope is called the Fracture-Spacing Index (FSI) (Narr and Suppe, 1991). Soliva, Benedicto and Maerten (2006) showed that the stress drop zone (stress shadow) due to the fault activities affects the fault spacing. Figure 1 shows the approach used to estimate the thickness of the mechanical layer from the fault spacing on Mars. This paper aims to better understand the internal mechanical structure of Mars estimated by the geometrical pattern of faults on the Martian surface. We report the initial studies of this work. The lab-scale physical experiments and numerical experiments were presented to demonstrate the relationship between the thickness of the mechanical layer and the geometric pattern of fractures

Nov 29, 2022

Full aerodynamic design development of the proposed fans for the enlarged primary ventilation system at Mount Isa Mines Limited was initiated before tender specifications were prepared. Theoretical and analytical design studies were made of many possibilities to determine the optimum proposal. Major considerations were efficiency, simplicity, standardization, and mechanical feasibility. Model testing and experimental work covered blading design, inlet shape, diffuser and tail fairing dimensions, instrumentation requirements, ancl noise studies.Theoretical and predicted performance estimates were prepared for the three 20 ft diameter vertically mounted axial flow fans.

Jan 1, 1967