Search Documents

A series of physical tests have been conducted to determine the actual performance of bunton to shaft side wall connections typically used in new shaft construction in South Africa. The test set-up is described, together with the applied loading, which incorporates a cyclical load component and a quasi-static load component, in an attempt to simulate actual conditions in the shaft. The test results are given and it is shown that generally the performance is adequate, provided double-slotted holes are not used. Generally the fatigue performance is found to be good, with the only exception being cases where the bottom of the bunton is lower than the seating level for the bunton to side wall connection. Arising from the tests, typical design values of connection stiffness, strength and fatigue life are proposed and a design procedure including these three key aspects of connections is described.

Jan 1, 2005

The process of establishing the design criteria is the key step in commencing a new project.. The method for establishing design criteria and translating them to a workable plant design is described. INTRODUCTION The use of activated charcoal to recover gold from alkaline cyanide leach liquors is the most rapidly expanding technology in hydrometallurgy today. The process, known as carbon-in-pulp (CIP), has replaced countercurrent decantation as the method for recovering gold by cyanidation. Carbon-in-pulp entails mixing activated charcoal with a ground ore-water slurry containing gold cyanide, allowing the charcoal to adsorb the gold, and then mechanically removing the gold loaded charcoal from the pulp. The pulp is sent to tailing disposal and the loaded charcoal is sent for gold bullion production. Activated charcoal's affinity for gold has been docu- mented for over one hundred years. In the first cyanide plants, one of the preferred methods of stealing gold was to place a piece

Jan 1, 1982

Acid rock drainage (ARD) derived from sulphide oxidation and the associated metal leaching is the most significant environmental issue facing the mining industry today. Under given hydrological and biogeochemical conditions, the local geology and mineralogy largely control the formation of ARD. The involvement of a geologist is therefore essential in minesite ARD assessment and prevention. The relevant tasks that a mine geologist may undertake at three major phases of a mining project are briefly described. Additional knowledge that a mine geologist should acquire in order to achieve proficiency in ARD assessment is also suggested.

Jan 1, 1993

By J Jeffrey, G W. Wilson, L Gilbert, C

Prior to the commencement of mining, the acid rock drainage (ARD) potential of the waste rock to be produced by an open cut mining operation is assessed by a variety of techniques carried out on drill-hole samples. These include, among others, acid base accounting (ABA), net acid generation (NAG) testing, and kinetic testing. Based on the results obtained, a strategy for the identification, separation and selective placement of waste rock having different potentials to form ARD is developed. During the course of mining, the waste rock classification scheme will be re-assessed periodically to confirm that it is appropriate. This re-evaluation may result in a change in classification scheme, and waste rock dump samples may be obtained for ARD assay purposes to confirm the appropriateness of the revised scheme. The paper describes the evolution over time of the scheme used to classify waste rock at a major open pit gold operation in New South Wales, Australia, including the development of a hydrological model. To confirm the appropriateness of the revised scheme, ARD assay testing was carried out on drill-hole samples collected from dumps having different ARD potential designations, including Non-Acid Forming (NAF), Potentially Acid Forming (PAF), and Low Grade Ore stockpiles. The results of the ARD assay testing and water quality monitoring confirmed the appropriateness of the ARD potential designations and the revised classification scheme, which has been adopted.

Jan 1, 2003

Sluice-boxes are by far the most widely used concentrating devices by small-scale operators in PNG who work alluvial gold deposits. The sluice-box designs and their operating conditions used are known to vary widely. The selection of sluice-box configuration and the operating parameters such as the water flow rate is purely based on past experience. Some use small flowrates to increase the fine gold recovery at the expense of efficient separations and capacity while others use high flow rates resulting in increased fine gold losses but with high throughput rates. Recent work has revealed that the combination of riffle height, their spacing and wash water flow rate are the most important parameters that determine the success or failure of such operations. This combination has been shown to depend on the in situ gold and gangue size distributions of the deposit being processed. This paper describes a design procedure which uses a non-linear optimisation method to determine the optimal combination of the above parameters to maximise the metallurgical efficiency of such operations.

Jan 1, 1993

By D Purdy, K Wilkinson, P Blake, M Fitzell, J McLellan, L Feltrin, O Dixon

The northern Drummond and Bowen basins region represents one of AustraliaÆs most prospective areas for epithermal vein and stockwork style gold deposits, with both low and high sulfidation epithermal mineralisation known in the region. 3D-GIS reconstructions, numerical and probabilistic modelling (UDEC, FLAC 3D and WofE) are used here to develop a better understanding of the controls operating on the mineral systems of the region and are aimed at enhancing predictive capabilities. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Ennis P. C

The Mt Keith ultramafic intrusive extends for about 200 kilometres from Agnew in the south to Wiluna in the north. It forms the host for a number of nickel sulphide orebodies including Mt Keith and Honeymoon Well. Long fibre minerals are associated with the orebodies. The presence of these minerals impacts on the issue of tailings disposal from several standpoints, particularly the slurry beaching properties and dust generation from dry beaches. Central thickened discharge (CTD) is an innovative method of tailings disposal that involves stacking tailings in a low conical hill instead of storing them in cells. In appropriate circumstances this leads to savings in capital costs and operating expenditure. The method was introduced to Australia in 1981, and is currently employed at four operating mines, Elura and Peak Gold, both at Cobar in NSW, McArthur River in the Northern Territory, and Union Reefs near Pine Creek, also in the Northern Territory. It is the proposed method for Century Zinc and Ernest Henry, both in Queensland. The paper describes laboratory test work and design parameters for the application of the method to tailings disposal at Honeymoon Well and compares them with comparable data for other CTD systems. Of particular relevance for design purposes are beach slope, density, and water recovery. Wind tunnel tests were conducted on the Honeymoon Well tailings samples to investigate dust generation from the dry beach surface and it was concluded that dust generation from an undisturbed beach would not occur because of crusting.

Jan 1, 1996

By P J. Harris, D J. Bradshaw

Surface oxidation of sulfide minerals, such as that found in the regions of a sulfide ore body near the water table, can have a significant impact upon flotation. This theme has been explored for Merensky ore type sulfides where an ore containing pyrrhotite, pentlandite and chalcopyrite was thermally oxidised and the role of potential remedies investigated. Back-scattered scanning electron microscope images are presented showing the oxidation layer which formed in the mineral surfaces. These oxidation layers were depleted in both sulfur and iron with incorporated oxygen. Flotation recovery rapidly decreased with increasing oxidation, particularly after 27 days and reached a plateau after 50 days. Up to 27 days, this effect could be partially overcome with higher collector additions. Oxidation had more impact upon the finer size fractions, particularly for pyrrhotite. For more heavily surface oxidised samples, ultrasonic treatment prior to collector conditioning was found to improve flotation recoveries. This treatment had the greatest effect upon chalcopyrite particles. Sulfidisation was successful in restoring the flotation recovery of the heavily oxidised sulfide minerals. Longer sulfidisation conditioning times were not conducive to good flotation recoveries of both oxidised pyrrhotite and pentlandite due to oxidation of the freshly formed sulfide surfaces. For maximum flotation recoveries of oxidised pyrrhotite, pentlandite and chalcopyrite, different sulfidisation conditions are indicated. It appears likely that in a mineral processing operation treating oxidised Merensky type ores, two stages of sulfidisation employing different conditions would be required.

Jan 1, 2005

By Johnson N. W, Manlapig E. V, Alexander D. J, Franzidis J. P

The importance of the froth region on flotation performance is often emphasised in the literature. It is well-known that decreasing froth depth or increasing air flowrate results in increasing cell recovery at the cost of lower concentrate gra

Jan 1, 1997

By T Clemens, D Trumm

Adopting environmentally acceptable practices in New Zealand is a crucial requirement for mineral wealth development. Recent planned expansions in the coal industry have increasingly placed mining in the media spotlight. A lack of appropriate national environmental guidelines has resulted in inconsistent responses and assessments of current and prospective mine sites. Such inconsistencies have lead to delays in decisions on developing economic mineral deposits that may have only minor short-term impacts, and have also allowed unacceptable environmental management practices to continue elsewhere.   A research collaboration between CRL Energy, Landcare Research, University of Canterbury and University of Otago aims to provide regulator groups and the mining industry with a unified approach to the requirements of the Resource Management Act 1991, which is the legislation that predominantly drives the nationÆs environmental policies and guidelines. The tangible outcome of this research programme will be guidelines for an integrated decision-making framework based upon robust multidisciplinary science. The result of this unified process will facilitate the development of viable mineral deposits and prevent excessive environmental impacts.   The framework will be derived from a synthesis of four objectives. Objective 1 identifies potential water quality impact. This objective is based on a targeted geochemical study of the lithology and waterways of the West Coast and Southland. Objective 2 categorises the degree of impacts on the ecology of receiving aquatic ecosystems and determines the processes that drive aquatic ecosystem recovery. Objective 3 identifies best strategies to sufficiently manage impacted ecosystems, and to prevent future unacceptable impacts. Objective 4 combines the findings of Objectives 1 - 3 into a standard decision-making framework. The development of this framework development will include wide consultation with representatives of the mining industry and regulator groups. It is anticipated that this multidisciplinary approach will provide a robust and coherent, standardised system that will assist in achieving industry and environmental targets.

Jan 1, 2004

By Hossaini SMF

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Ramamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris: 611=1+B(63)O.825 acm 6cm where a1= axial compressive stress at failure, MPa; a3 = confining pressure, MPa; acm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (aim ) -0.185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By J Gutzmer

The Kalahari Manganese Deposit in South Africa accounts for 80 per cent of the worldÆs land-based mineable Mn reserves. Although the ores are primarily mined for export, South Africa is the worldÆs third largest producer of ferromanganese and ferrosilicomanganese alloy, both of which are derived from the smelting of these ores. Mineralogical analysis has traditionally been forsaken for bulk chemical assaying in quality control of smelter feeds, principally because quantitative data could not be easily produced. Yet, mineralogy plays a vital role in determining smelting behaviour, which in turn has economic implications when aspects such as energy and reductant consumption are considered. Smelting is an endothermic process, and the amount of energy input required is dependent on the minerals present in the ore, as well as their relative proportions. Further, knowing the bulk Mn oxidation state in the ores allows for calculation of the amount of oxygen that must be driven off to produce alloy, and hence the amount of reductant required. Additionally, certain minerals can be correlated with potentially deleterious elements, so that ore mineralogy can indicate penalty element distribution. Mineral abundance analysis was conducted on ores from the Kalahari Manganese Deposit using quantitative X-ray powder diffraction. Rietveld refinement using a fundamental parameters approach was applied to micronised ore samples. The mineral percentages obtained were validated using mineral chemical data together with bulk major element data derived from ICP-OES. Bulk oxidation state partitioning was then carried out knowing the Mn valence in the minerals. The results show potential for implementation of the proposed method on a smelting plant, where ore blending could be then implemented to achieve consistent feed compositions to smelters. Selective mining could also be undertaken to obtain desirable ore compositions for domestic or international markets.

Jan 1, 2008

By Buisman C. J N, Koch R. O

Soil and groundwater beneath the Budelco zinc production plant at Budel-Dorplein (The Netherlands) are contaminated with metals and sulphate. To avoid contamination of nearby drinking water aquifers in the very distant future, a geohydrological containment system (GCS) and a microbial treatment plant for extracted contaminated groundwater have been developed. As a first step in the design of the system groundwater data from over 150 wells and geological profiles were used to model geohydrological conditions beneath the site. Several configurations of water-extraction wells were deduced from the model. Data gathered during additional fieldwork were then used to improve the model. Finally results that were calculated for the various configurations were used to select an optimal groundwater containment system. Currently some 5000 m3/day groundwater are extracted from a combination of 12 shallow and deep wells. Heavy metals and sulphate have to be removed from the extracted water before it can be discharged into the river system or used as process water. Several water treatment methods have been studied and pilot-tested at the site. The preferred and selected process is based on the activity of sulphate reducing bacteria (SRB) and combines sulphate removal and heavy metal removal in one single step. The anaerobic bacteria reduce the sulphate to sulphide resulting in the precipitation of metal sulphides. A pilot plant gave promising results and a commercial-scale plant has been designed. The proposed design has been tested in a demonstration plant which included all main process units. Test results for all process units are presented. The collected information was then used to optimise the design of the commercial-scale plant. Special attention was paid to automation and safety items. Construction of the plant was finished in May 1992. Start-up, commissioning and operational experience are reported. The concentrations of metals and sulphate in the effluent of the SRB water treatment plant are well within the limits set by the authorities for discharge to public waters.

Jan 1, 1993

Mining is an intensive resource development industry, where operations are often of relatively short duration and can result in dramatic impacts on the natural environment during the operational period and for many years post mining. An integral component of all mining operations is water û through exploration, resource definition, mine development and operation, rehabilitation and the long-term post-mining land use. Water is a basic requirement in the provision of worker amenities, in drilling, as a means of dust suppression, as a medium for washing or processing the mine product, and as an aid in establishing vegetation on post-mining landforms. Water also plays an important role in mobilising environmental contaminants and is the primary medium for the transport of contaminants off the mine or processing site into the wider environment. It is for this second reason that the mining industry considers water management as a key component of mine management. Cost-effective water management relies on planning that incorporates a total mine system approach commencing prior to exploration and continuing through to rehabilitation and decommissioning. One of the primary considerations that will provide confidence to both government and community at the time of mine closure and lease relinquishment, will be the evidence that any water originating from, or passing through, the mine site is of a quality that will not have any negative impact on the surrounding environs into the future. The role of vegetation in stabilising disturbances to a landscape is well known, as is the recognition of vegetation being a fundamental component of the water cycle through the physiological processes resulting in the transfer of water back to the atmosphere through transpiration. In terms of water management at a mine site, the two crucial issues are the æquantityÆ and æqualityÆ of water that enters a receiving æoff-leaseÆ catchment. In terms of tolerances of the receiving environment, the total load of potential contaminants becomes critical, a reduction in which can be achieved through reduced volumes of water discharged, reduced chemical and physical concentrations of contaminants in that water, and ideally, both. This paper examines the potential role of vegetation in reducing the quantity of water released from a site, and secondly considers vegetation in the role of influencing the quality of that water.

Jan 1, 2003

By Wiltshire PG

The process uses sodium hydroxide and sodium nitrate reagents as in conventional Harris refining plants, selectively removing the arsenic to the caustic phase at an operating temperature of 420-450¦C. A novel feature of the process concept is continuous treatment of loaded caustic slag for recovery of arsenic as a sandy crystal product suitable for further processing to arsenic trioxide. A large pilot plant was constructed and operated over a period of 3 years to develop materials handling techniques and equipment components and to prove the concept. Stable operations were achieved at equivalent capacities of 200 tonne/yr arsenic removal. The process is being considered in plans for expansion of bullion softening capacity at Port Pirie.

Jan 1, 1984

By D S. Scovira

The effect of blast vibration on highwall stability is a common concern for many open pit mines. Vibration in such a case is a typical near-field blast vibration situation. Vibration modelling in the near-field of a blast requires consideration of both the amplitude and frequency attenuation of waveforms with distance. Most existing blast vibration models are designed for far-field vibration and do not simulate the frequency attenuation and its effect on waveform shape. With the advent of electronic detonators it is desirable to quantify the effects of blast delay on the amplitude as well as the frequency of blast vibrations. A suitable modelling tool is proposed here. At present, a blast vibration model with double attenuations(amplitude and frequency) has been developed at Orica. The present model simulates the amplitude and frequency attenuations separately using different transfer functions. The amplitude attenuation is modelled according to the non-linear relation between the peak particle velocity (PPV) and the charge weight scaled distance established from the signature hole vibration. The frequency attenuation is modelled with the signal broadening based on KjartanssonÆs transfer function û a linear model for attenuation of waves. The model is capable of taking multiple sets of signature waveforms as input to improve the modelling accuracy of the wave propagation in the geology at a site. The screening effect of the earlier firing holes in the path of a later firing hole is taken into account on not only the amplitude, but also frequency attenuation. The present blast vibration model is suitable for modelling both near-field and far-field blast vibrations. It yields reasonable agreement with measured field data for the near-field vibration examples discussed.

Jan 1, 2007

This paper describes the technique developed by the Australian Coal Industry Research Laboratories (ACIRL) for the treatment of bore core samples to obtain data for coal preparation studies of the target reserves. The particle size distribution within the sample has a significant influence on the relationship between the yield and ash per cent of the floats coal at any ash level. The size analysis within the reconstituted feed from a coal preparation plant is determined by the size analysis of the feed coal, physical degradation of material in the process, and the breakdown of associated shales in water. The extent of material breakdown was studied in the ACIRL coal preparation pilot plants. The method of bore core evaluation includes simulation of this breakdown in a sample selectively crushed to conform with predicted or known run-of-mine size distribution. Modifications have also been made to the laboratory methods for froth flotation to approximate more closely with industrial practice.

Jan 1, 1977

By J Champa

The mining industry internationally seems on the verge of a major underground support revolution as suppliers, mines, consultants and researchers develop, test and use thin support (structural) membranes (or superskins as they are commonly called) mainly as a replacement for screen/wire mesh. Thick membrane support in the form of shotcrete (sprayed concrete) has been used since the 1950s in underground mines. Shotcrete, in mines, is generally applied at a thickness between 25 and 100 mm depending on the need. Thin membranes are however applied at a typical thickness between 2 and 6 mm. Certain thin membranes have been available for several years (Tannant et al, 1999), but the intense interest in such supports has only grown in the last few years. The interest lies mainly in the potential to safely reduce the mining cycle time and hence improve productivity. There is however considerable confusion concerning such supports, and this paper attempts to clarify certain aspects and dispel certain misconceptions and myths about thin support membranes.

Jan 1, 2000

For several years, the Geology Department of the University of Canterbury has hosted a series of postgraduate projects in the field of coal studies, supported principally by the Ministry of Energy and to a lesser extent by private companies. These projects have involved mainly West Coast Coalfields, and my own studies have focussed on inorganic geochemical aspects of West Coast coals. Because of the large number of potentially important analyte elements in coal, and the wide diversity of coals occurring in the West Coast region, this project has required a substantial amount of work to be spent on sample collection, sample preparation, development of analytical methods, and actual analysis. Considerable problems must be faced at the sampling stage: Can sufficient information be obtained from whole-seam composites, or should seams be sampled in plies. Ply analysis is preferable, but results of proximate analyses are usually available for composites only. Where multi-seam drillhole samples become available (eg Greymouth Coalfield, where some holes yielded more than six sampled seams), the ply option involves a dramatic increase in the number of samples. I have attempted to strike a workable compromise between geographical coverage of coalfields, and detailed sampling of individual seams at each locality. In many cases, sample material has been used jointly with Jane Newman who has carried out petrographic studies.

Jan 1, 1985

An approximate rapid design system for tunnel liners and underground structures is presented which permits the effects of structure geometry and stiffness, rock quality in terms of its deformation modulus, and the applied system loading to be entered as data to produce direct designs conforming to stress limitations, optimum reinforcement requirements and restraints on section dimensions. An 'equivalent column' concept is introduced for modelling the rock mass in contact with the structure. Only the rock treatment is given in detail but the results of sensitivity analyses, with reference to rock quality, for a typical liner design are given and these results related to a number of empirical design approaches.

Jan 1, 1976