Search Documents

By R W. Wilson, A R. Branch, T S. Pooe

The original bulk air cooling system at this particular mine made use of two water chilling refrigeration machines to produce peak cooling of approximately 12 MWR with a downcast air temperature of about 7°C; however, as the shaft is not used for transporting personnel, the opportunity existed to supply more cooling to the mine by lowering the downcast air temperature. An ice storage facility has been constructed and provides a range of opportunities in operating the system: colder air temperature sent to the shaft, enabled by using near-zero degree water produced by melting ice to cool the air; electricity time-of-use management, by shifting electricity usage out of peak tariff periods; and increased peak cooling capacity, by melting ice while chilling water. Ice is created in the storage facility at night while the ambient air temperature is low and then melted to produce cold water when required by the cooling process. An ice dam was constructed and serpentine stainless steel coils installed where the ice is produced; one of the refrigeration machines was converted to chill a glycol solution to subzero temperatures to create the ice on the coils; a plate heat exchanger was installed to allow the glycol chiller to act as a water chiller as well; and a third spray stage was added to the bulk air cooler to utilise the near-zero water. This paper describes the thermodynamic design, construction and performance assessment of the new system, which is unique, novel and represents the state-of-the-art of this type of cooling system and energy management.CITATION:Branch, A R, Wilson, R W and Pooe, T S, 2015. Novel use of ice thermal storage for energy management on a mine refrigeration plant, in Proceedings The Australian Mine Ventilation Conference, pp 185–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Thomas L. J

A series of tests on rock stress measurement devices used with the overcoring method indicated that improvements could be made in their construction. A prototype inclusion cell was developed with strain gauge rosettes bonded to a 0.05 mm thickness stainless steel sheet which was formed into a cylinder around two end pieces. The finished diameter was slightly larger than previous cells so that the thinner plate and the reduced annulus of Araldite cement in the installation borehole gave a better response in the laboratory than the other cells tested, especially in simulated bedded rock. It was less affected by inhomogeneity and temperature changes. Its high sensitivity should make it suitable for both absolute stress measurement and field monitoring. A table of comparative readings is given for the new cell and for four other devices used in simulated in-situ rock conditions.

Jan 1, 1992

In the future to excavate sufficient coal for power generation, two dredgers would be required to dig overburden or interseam 70010 of the time and three dredgers 40010 of the time. One overburden system was not adequate for this requirement, making coal production reliability vulnerable. TS5 spreader is the new machine element of this system. The selection of the best type of machine configuration to suit the application was then subject to an internal SECV VE Study, a registration of interest and a tender for two machine alternatives. This paper outlines the reasons why SECV planned the Secondary Overburden System and how the Krupp machine met these requirements. It also identifies the main design features of the machine and its constructability which will allow the machine to be operational by the end of May, 1990.

Jan 1, 1989

The series of events leading to the adoption of more complex flotation circuits for coal have been reviewed. In essence, it has been concluded that ac- ceptable overall flotation recovery will only be obtained when efficient distri- bution of collector over all the component feed size fractions is ensured. The achievement of this goal is most likely to be obtained by feed classification and separate flotation of appropriate size fractions. The adoption of such a phil- osophy, however, imposes a number of process problems of both a chemical and an engineering nature. Some of these problems have been identified and possible solutions discussed. A case is emerging for the development of a new generation of flotation cells designed specifically for the flotation of classified coal and for the development of a series of novel re- agents which have the propensity to float middling particles.

Jan 1, 1984

By Sorokin M. L, Komkov A. A

Flash smelting of nickel sulphide concentrate has been practiced at WMC's Kalgoorlie Nickel Smelter for 20 years. The mineralogy of the concentrate from the original mines was particularly suited to this process. However, taking a strategic view, potential new processing routes should be fully evaluated as possible replacements for the current technology. The Vanyukov process has been under development in Russia for the past 40 years and has been successfully applied on a large scale to the smelting of copper concentrates, at two locations - Norilsk and Balkhash. The potential for the application of the Vanyukov process to the smelting of nickel concentrates offers a number of processing advantages, including smaller reactor and decreased dependence on fuel oil. This paper reports on preliminary investigations into the application of the Vanyukov process to the smelting of nickel concentrates. At this stage the investigations are limited to semi-quantitative comparisons and modelling studies.

Jan 1, 1992

The role of the mine geologist in a business perspective is self-evident to some, but to others it may be a new concept. All mine geologists need to know exactly how they add value to the business if they are to be successful. Alternatively, if they do not add value, then they will become redundant. This paper seeks to understand some of the contributing problems that hinder the mine geologist from operating in a business perspective. In doing so, a new context (for some) is proposed to aid the mine geologist and the operation gain greater value from geology. The proposal suggests how to ensure that the activities of our geologists are intrinsically linked to the business process that we are involved in. The mine geologist can and must play a pivotal role in the success of an operation. To do this, they must understand some principles of business such as:process, customer/supplier relationships, and organisational structure. Our geologists must know the business objectives, understand the product that the customer needs and use their geological skills to deliver the product safely, on time and to specification. As geologists, we can be instrumental in ensuring that the operational environment is structured in such a way that maximum value is realised, not only from the mine geologists but the entire site team. In doing so, mine geologists will realise their full potential in delivering the outcomes the business demand, and therefore be recognised as strong contributors to business success.

Jan 1, 2000

By Gottlieb P, Sutherland DN

The paper describes a method of making quantitative mineralogical measurements on many of the major lead/zinc orebodies in Australia. The work was done using QEM*SEM. It was found that a relationship betwen phase-specific surface area and particle size, when plotted in a suitable way, gave a straight line with slope related to the grain size of the mineral in question. The method provides an excellent way of differen- tiating between minerals in existing orebodies and, consequently, an easy way to establish a comparison between a new prospect or orezone and current operations.

Jan 1, 1988

By Miskelly N

In Australia and New Zealand, the 'Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves', which was released by industry in 1989, is operating successfully in a co-operative approach between industry and regulatory authorities. Similar codes or guidelines exist or are under development in the United States of America, Canada, the United Kingdom and South Africa, although the regulatory backing given to the Australasian Code is unique. International standard definitions for Mineral Resources and Reserves, and for categories of Resources and Reserves, have been under development by the Council of Mining and Metallurgical Institutions since 1994 and have already stimulated considerable convergence of definitions and reporting standards in participating countries. It is hoped that agreement on this international standard for public reporting by mining companies will be reached within the next two years, and it is expected that adoption of the standard will result in a higher and more uniform quality of reporting worldwide, with a consequently greater interest on the part of the general public and financiers in investing in the mining industry.

Jan 1, 1997

By Kellerwessel H, Oberheuser

Since its invention by Professor Klaus Schonert of the University of Clausthal, Germany, high pressure rolls comminution has attained near total acceptance as the preferred method of size reduction in the cement industry. Over 300 units have been manufactured worldwide. At locations where the system has been installed, considerable energy savings have been realised. These energy savings are generally in the range of 20 to 30 per cent compared to conventional ball mill circuits. However up to 50 per cent power saving has been achieved at some installations. This technology, with the exception of the diamond industry, has up to now had only limited success in ore processing. This has mainly been attributable to the abrasiveness of ores encountered in this industry leading to high wear rates. These high wear rates have given rise to an unacceptably short life time of the wear surface of the rolls, requiring regular replacement. A new wear surface has been developed which has shown to give a ten-fold increase in service life over conventional surfaces. This, together with developments made in machine design now give the units the ability to attain the high availabilities demanded by the mining industry, and therefore to allow this industry to achieve the considerable operating cost savings offered by the high pressure rolls.

Jan 1, 1992

By L C. Thompson

BioLix is the term for a new class of biologically-derived lixiviants for precious metals (gold and silver) recovery. BioLix can be used as an alternative to cyanide on virgin and spent ores. The BioLix process is based on inducing microbial enzymatic reactions that generate organo-lixiviant chemicals. The bioprocess involves a two-stage culture strategy. First, specialty microorganisms are cultured to generate a high biomass. Then, a food-grade quality amendment is introduced that forces the microorganisms to produce the organo-lixiviant. The second-stage culture is applied to the ore where the microbial/lixiviant system acts on mineral surfaces to extract precious metals. The process operates at ambient temperatures and near neutral pH. This paper will examine the BioLix process through an extensive laboratory development and demonstration project. Laboratory development consisted of identifying and isolating specialty microorganisms and inducing agents for the production of the organo-lixiviant solutions. A demonstration was performed on low-grade and high-grade oxidised ore from the Buffalo Valley mine in Nevada, USA. Results indicate that the BioLix process was comparable to cyanide in terms of gold recovery and operated at near neutral pH and ambient temperatures. Applications for the BioLix process will be discussed including spent-ore re-leaching, cyanide replacement for virgin ore, and in situ mining.

Jan 1, 2004

The first geological maps of parts of Australia were produced in the 1830s and 1840s, many being for purely practical purposes, such as indicating the occurrence of coal, iron and other essential materials. Mineral location maps were also first made about the same time.More systematic geological mapping commenced in the 1850s when large parts of New South Wales and Victoria were studied in government-sponsored surveys by geologists such as Samuel Stutchbury, Alfred Selwyn and Reverend William B. Clarke. Their work coincided with the opening up of most of the major goldfields of eastern Australia, which led to the establishment of Departments of Mines in the separate Colonies (later States within the Commonwealth of Australia).A few companies employed consultant geologists at this time, and the mapping by Frederick Odernheimer is particularly notable. Geological study of Australian ore-deposits and mineralisedareas was influenced by the continental European geological ideas of men such as Odernheimer as well as by those from England. Both geological and mineral maps were a feature of Colonialdisplays presented at major international exhibitions during the second half of the nineteenth century. The maps accompanied rock and mineral collections which showed the known and potential mineral wealth of the Colonies. Such displays raised interest in the potential for development amongst government officials, entrepreneurs and investors in Australia and abroad.By the 1880s most of the Colonies had produced basic geological maps, and several maps of the whole continent had been published. Although systematic mapping of the continent become a reality only in the 1950s, the nineteenth century geological and mineral mapping formed the basis for the development of the major coal, artesian water, and metalliferous mining regions of Australia.

Jan 1, 1990

As economic, technological, regulatory and other forces continue to present the global mining industry with new opportunities and challenges, agile mining equipment manufacturers are stepping up their efforts to anticipate and meet the evolving needs of surface and underground mining operations. Operational excellence û the pursuit of efficient, lowest-possible-cost production û is a prime objective for all mines. As mineral commodity markets experience cyclical price highs and lows, mine operators, increasingly, look to their equipment suppliers for equipment and support that can help reduce multiple tangible and intangible operating costs. This paper explores how two mining equipment manufacturers û P&H Mining Equipment, a supplier of surface mining equipment and Joy Mining Machinery, a supplier of machinery for underground mining û are responding to the mining industryÆs aggressive pursuit of obtaining reduced operating cost with innovative products and support programs.

Jan 1, 2000

Mineral sands are being used as the source material for new "high-tech" engineering materials. One such material, Magnesia Partially Stabilized Zirconia (PSZ) has been developed and patented world-wide by CSIRO. Derived from zircon sands, the material is currently produced by Nilcra Ceramics in Australia and is exported world-wide.The properties of the material are contrary to those generally accepted for ceramics and are far more akin to those of steel. The material resists not only abrasive wear, impact and thermal shock, but does so under corrosive conditions that frequently cause early failure of metal and cemented carbide.While the consumption of mineral sands for the production of PSZ is not going to significantly increase the demand in the short term, the material itself may well assist the productivity and processing problems within the industry.

Jan 1, 1986

The weathering of different types of base metal deposits in the semi-arid environment of the Lachlan Fold Belt of western New South Wales affects the geochemistry of outcropping ironstones (gossans) and derived soils. W eathering of the pyrite- and pyrrhotite-rich mineralisation at the Elura Zn-Pb-Ag deposit leads to highly acidic conditions and strong depletion of Cd and Zn throughout the profile. There are local attainments of high concentrations of Ag, As, Ba, Cu, Hg, Pb, Sb and Sn in the profile and As, Ba, Pb and Sb are still highly anomalous in surficial material (ironstone and soil). However, at Parkers Hill, in the Mineral Hill Field, the primary Zn-Pb mineralisation is pyrite-poor and so weathering is not as acidic as at Elura. Thus, although Ag, As, Cd, Cu, Sb and Zn may be concentrated at various levels in the Parkers Hill weathering profile, Cu and Zn (as well as As, Pb and Sb) are retained in surficial ironstones in essentially the same abundances as in primary mineralisation. Thus, variations in the suite of geochemical indicators present in ironstones and residual soils are likely to reflect differences in the original mineralogy and the degree of acidity produced during the weathering of base metal mineralisation. Hence, an understanding of weathering processes is necessary to fully interpret exploration geochemical data.

Jan 1, 2004

By S Chaudari, T Ren, T Harvey

Management of respirable dust on longwall face remains a challenging issue for mine operators, particularly for the new generation of thick seam longwalls. A fundamental understanding of the airflow behaviour around the shearer is critical for dealing with the dust control issue on longwall faces. Computational fluid dynamics (CFD) modelling techniques have been used in this study to conduct a detailed investigation of the air and respirable dust flow patterns around the longwall shearer. Three CFD models have been developed to represent different longwall cutting heights. The results of these modelling studies tallied well with field measured airflow data from different mines. The validated thick seam longwall face model was then used for detailed parametric studies to simulate the effect of various parameters and dust control concepts. The dust control options investigated include various spray configurations, shearer clearer, modified cutting sequences and shearer scrubbers of various capacities to minimise the respirable dust migration towards the walkway area of the longwall face. This paper presents a summary of the results of these CFD modelling investigations.

Jan 1, 2005

By H G. Poulos

Prediction of ground deformation caused by soft ground tunnelling is an important problem facing design engineers. The ground deformations are caused by the closure of the gap formed around the tunnel due to the tunnelling procedure and soil intrusion via the tunnel face into the tunnel. There are three different approaches that are commonly used in practice to estimate the ground deformations due to tunnelling, namely, empirical methods, analytical methods and finite element methods. One of the important issues of tunnelling in urban areas is the assessment of the likely impact on adjacent pile foundations of ground movements arising from tunnel construction. The main objectives of this paper are two-fold: first, to assess the available methods to estimate the tunnelling-induced ground deformations, and second, to examine the effect of such ground deformations on adjacent piles. Analytical solutions to predict the tunnelling-induced ground deformation developed by the authors are used in this study. These estimated ground deformations are imposed on the pile in simplified boundary element analyses to compute pile responses. The influence of various factors such as tunnel geometry, ground loss ratio, pile diameter and ratio of pile length to tunnel depth are examined in this study.

Jan 1, 1999

Stereological transformation relies on knowledge of the textural characteristic that governs the relationship between the one-, two- and three-dimensional liberation spectrum. Transformation functions can be built from fractionation of real mineralogical particles. Alternatively, transformation functions can be built from simulated textures, geometrical textures or artificial textures. These transformation functions can be useful when the texture of an ore has not yet been characterised for the preliminary assessment of liberation. Recently, Lin et al (1995) developed a methodology for generating such an artificial texture. The artificial texture can be used to produce broken particles of known volumetric composition. Data from image analysis on several artificially generated samples is readily available, and can be used to build the associated stereological transformation function. In this work, the methodology for calculating the transformation function from LinÆs artificial texture is presented. The new texture is implemented for stereological transformation applications.

Jan 1, 2008

By Riley S

Many regulatory bodies have, or are considering, guidelines that require rehabilitated mine spoils to be erosionally stable (satisfying quantitative limits) over specified design lifetimes. One of the problems facing the industry is that many of the computer models used for erosion assessment were developed for agricultural applications and are unable to predict the change in the shape of engineered landforms over extended periods of time. In particular, they cannot predict where valleys and gullies will develop in the landforms and how big or deep they will be. Furthermore, many existing models require considerable skill to use. A computer model (SIBERIA) developed by the first author, able to model this valley and gully development over long design lifetimes, and which is directly based on digital terrain maps is discussed here. Proposed rehabilitation strategies for waste rock dumps at Ranger Uranium Mine as assessed with SIBERIA are discussed. New features of SIBERIA of interest to the mining industry include the spatial distribution of erosion, deposition and gully development, and various measures of the quantitative risk of failure. A collaborative project with the Queensland Coal Association, involving the first author, aims to deliver these capabilities to the coal industry in a user-friendly package. The objective is the cost-effective rehabilitation of strip mines. Some preliminary results from this project are presented.

Jan 1, 1994

By A J. Morrison, M Yahyaei, J S. Siong, J Wang, K Runge

The flotation cells used to upgrade ultrafine metallurgical coal (-250 µm) are usually poorly controlled leading to unnecessary loss of combustibles from the flotation system. This is mainly because coal flotation cells are typically controlled for process stability rather than optimisation of flotation performance. This is especially true for a flotation device commonly used in coal applications in Australia – the Jameson Cell. This then provides an opportunity to improve the flotation performance by shifting from a stabilising control strategy to a proactive optimising control strategy. For an optimising control strategy, the control system will require a means of relating and then measuring in real-time, the effect of changing operating conditions on the coal flotation performance. Hence, the major aim of this work is to propose a possible model-informed process control strategy that could be used for real-time performance optimisation. In this study, industrial site work was conducted on an industrial-scaled Jameson Cell at a Coal Handling and Preparation Plant (CHPP) in Central Queensland, Australia where superficial gas velocity was controlled to six different levels. At the same time, other process variables such as froth depth and flotation feed properties were measured. The empirical models developed from this study suggested that combustible recovery is a function of superficial gas velocity, froth depth, feed solid content and feed ash content and that a peak in combustible recovery existed as a function of superficial gas velocity. This led to the development of a model-informed control strategy that aimed to maximise the combustible recovery by determining and then operating the cell at the superficial gas velocity at which the peak occurs. This peak superficial gas velocity was found to be only a function of feed solid content. Based on these findings it would seem possible to operate a Jameson cell at peak performance by online measurement of feed solid content, prediction of the optimum superficial gas velocity and stabilising control to maintain operation at that superficial gas velocity set point. The development of this modelinformed control strategy can serve as a basis for the development of a more sophisticated modelpredictive control (MPC) system. However, more work will need to be done to improve the predictivity of the combustible recovery model by measuring and modelling performance over a wider range of operating conditions.

Aug 24, 2022

Over the last five years Du Pont (Australia) Ltd has developed a commercial range of new generation emulsion based explosives concurrently with the development of new explosives-placement systems. The paper outlines Du Pont's emulsion technology and history of product development from the initial emulsions (Tovex E & EL) to emulsion/ANFO blends (Tovex BE) through to the most recent development of Du Pont's SOL emulsion component. The paper also outlines the development of materials handling systems on site to load waterproof bulk explosives from the original pumper trucks through to the multipurpose agitator bowl blending and pumping units at the heart of Du Pont's SOL emulsion system currently available within Australia. The last section deals with some of the more important features of enhanced agitator bowl truck designs and outlines examples of the complete SOL emulsion system and methods of operations currently practiced at specific mines within the Bowen Basin coalfields.

Jan 1, 1986